Electrocatalytic Oxygen Reduction Reaction Research Articles

Fe-N co-doped carbon nanofibers with Fe3C decoration for water activation induced oxygen reduction reaction

ABSTRACT Proton activity at the electrified interface is central to the kinetics of proton-coupled electron transfer (PCET) reactions in electrocatalytic oxygen reduction reaction (ORR). Here, we construct an efficient Fe3C water activation site in Fe-N co-doped carbon nanofibers (Fe3C-Fe1/CNT) using an electrospinning-pyrolysis-etching strategy to improve interfacial hydrogen bonding interactions with oxygen intermediates during ORR. In situ Fourier transform infrared spectroscopy and density functional theory studies identified delocalized electrons as key to water activation kinetics. Specifically, the strong electronic perturbation of the Fe–N4 sites by Fe3C disrupts the symmetric electron density distribution, allowing more free electrons to activate the dissociation of interfacial water, thereby promoting hydrogen bond formation. This process ultimately controls the PCET kinetics for enhanced ORR. The Fe3C-Fe1/CNT catalyst demonstrates a half-wave potential of 0.83 V in acidic media and 0.91 V in alkaline media, along with strong performance in H2-O2 fuel cells and Al-air batteries.

Influence of Nitrogen Position on the Electrocatalytic Performance of B,N-Codoped Carbon Quantum Dots for the Oxygen Reduction Reaction

Nanocomposites containing B,N-codoped carbon quantum dots (CQDs) and an anion exchange ionomer based on poly(2,6-dimethylpolyphenyleneoxide) with trimethylammonium groups on long side chains (PPO-LC) were studied as catalytic electrodes for the oxygen reduction reaction (ORR). The objective was to reveal the impact of graphitic vs pyridinic/pyrrolic nitrogen on the ORR electrocatalysis. The CQDs were prepared by hydrothermal synthesis and analyzed by X-ray photoelectron spectroscpy to ascertain the B and N content and their position. The electrodes were prepared by drop-casting an ink of CQDs and PPO-LC on acid-treated carbon paper support. Characterizations of the electrodes included water contact angle, capacitance measurements, Fourier transform infrared spectra as well as scanning electron microscopy and optical microscopy. The onset and half-wave potentials, limiting current densities, Koutecky-Levich and Tafel plots revealed that the sample with only pyridinic/pyrrolic nitrogen showed the lowest electrocatalytic performance, underlining the importance of graphitic nitrogen for good ORR activity. Four-electron reduction was observed for the samples containing graphitic nitrogen. The onset potential (0.92 V/RHE) was among the best in the literature for carbonaceous materials. Finally, durability tests were performed indicating a good long-time stability of the electrodes; the electrode degradation was analyzed by impedance spectroscopy.

Magnetic Order Transition of a Two-Dimensional Square-Lattice Electrocatalyst Assembled by Fe-N4 Units: Crucial Role on Oxygen Reduction.

Herein, we theoretically investigate the effect of magnetic orders on electrocatalytic oxygen reduction reaction (ORR) properties on the Fe-N4 site-embedded two-dimensional (2D) covalent organic framework (Fe-N4@COF-C3N2) under realistic environments. The Fe-N4@COF-C3N2 shows a 2D square-lattice (sql) topology with three magnetic order states: one ferromagnetic state (FM) and two antiferromagnetic states (AFM1 and AFM2). Specially, the electrocatalyst in the AFM2 state shows a remarkable onset potential of 0.80 V/reversible hydrogen electrode (RHE) at pH 1, superior to the existing most excellent noble-metal catalysts. Thermodynamically, the onset potential for the 4e- ORR is 0.64 V/RHE at pH 1, with a magnetic state transition process of FM → AFM1 → FM → FM → FM, while at pH 13, the onset potential for the 4e- ORR is 0.54 V/RHE, with the magnetic transition process of FM → FM → AFM1 → FM → FM. Generally, this finding will provide new avenues to rationally design the Fe-N4 electrocatalyst.

Linker Mediated Electronic-State Manipulation of Conjugated Organic Polymers Enabling Highly Efficient Oxygen Reduction.

Conjugated polymers with tailorable composition and microarchitecture are propitious for modulating catalytic properties and deciphering inherent structure-performance relationships. Herein, we report a facile linker engineering strategy to manipulate the electronic states of metallophthalocyanine conjugated polymers and uncover the vital role of organic linkers in facilitating electrocatalytic oxygen reduction reaction (ORR). Specifically, a set of cobalt phthalocyanine conjugated polymers (CoPc-CPs) wrapped onto carbon nanotubes (denoted CNTs@CoPc-CPs) are judiciously crafted via in situ assembling square-planar cobalt tetraaminophthalocyanine (CoPc(NH2)4) with different linear aromatic dialdehyde-based organic linkers in the presence of CNTs. Intriguingly, upon varying the electronic characteristic of organic linkers from terephthalaldehyde (TA) to 2,5-thiophenedicarboxaldehyde (TDA) and then to thieno/thiophene-2,5-dicarboxaldehyde (bTDA), their corresponding CNTs@CoPc-CPs exhibit gradually improved electrocatalytic ORR performance. More importantly, theoretical calculations reveal that the charge transfer from CoPc units to electron-withdrawing linkers (i.e., TDA and bTDA) drives the delocalization of Co d-orbital electrons, thereby downshifting the Co d-band energy level. Accordingly, the active Co centers with more positive valence state exhibit optimized binding energy toward ORR-relevant intermediates and thus a balanced adsorption/desorption pathway that endows significant enhancement in electrocatalytic ORR. This work demonstrates a molecular-level engineering route for rationally designing efficient polymer catalysts and gaining insightful understanding of electrocatalytic mechanisms.

Linker Mediated Electronic‐State Manipulation of Conjugated Organic Polymers Enabling Highly Efficient Oxygen Reduction

AbstractConjugated polymers with tailorable composition and microarchitecture are propitious for modulating catalytic properties and deciphering inherent structure‐performance relationships. Herein, we report a facile linker engineering strategy to manipulate the electronic states of metallophthalocyanine conjugated polymers and uncover the vital role of organic linkers in facilitating electrocatalytic oxygen reduction reaction (ORR). Specifically, a set of cobalt phthalocyanine conjugated polymers (CoPc‐CPs) wrapped onto carbon nanotubes (denoted CNTs@CoPc‐CPs) are judiciously crafted via in situ assembling square‐planar cobalt tetraaminophthalocyanine (CoPc(NH2)4) with different linear aromatic dialdehyde‐based organic linkers in the presence of CNTs. Intriguingly, upon varying the electronic characteristic of organic linkers from terephthalaldehyde (TA) to 2,5‐thiophenedicarboxaldehyde (TDA) and then to thieno/thiophene‐2,5‐dicarboxaldehyde (bTDA), their corresponding CNTs@CoPc‐CPs exhibit gradually improved electrocatalytic ORR performance. More importantly, theoretical calculations reveal that the charge transfer from CoPc units to electron‐withdrawing linkers (i.e., TDA and bTDA) drives the delocalization of Co d‐orbital electrons, thereby downshifting the Co d‐band energy level. Accordingly, the active Co centers with more positive valence state exhibit optimized binding energy toward ORR‐relevant intermediates and thus a balanced adsorption/desorption pathway that endows significant enhancement in electrocatalytic ORR. This work demonstrates a molecular‐level engineering route for rationally designing efficient polymer catalysts and gaining insightful understanding of electrocatalytic mechanisms.

Exploring Advanced Oxygen Reduction Reaction Electrocatalysts: The Potential of Metal-Free and Non-Pyrolyzed Covalent Organic Frameworks.

Oxygen reduction reaction (ORR) electrocatalysis is an area of increasing interest for the in-situ production of H2O2 or the development of energy-related devices such as hydrogen fuel cells. Although pyrolyzed catalysts still offer the best performances to date with reference to the organic-based catalysts, metal-free and non-pyrolyzed covalent organic frameworks (COFs) stands out as promising alternatives candidates due to their favourable characteristics such as crystallinity, porosity, and organic composition, allowing the study of structural-property relationships. Herein, we present the design principles and recent advances in COFs-based ORR electrocatalysts, demonstrating how composition influences the activity and electronic pathway of the oxygen reduction process.

Highly Dispersed Mn-Doped Ceria Supported on N-Doped Carbon Nanotubes for Enhanced Oxygen Reduction Reaction.

The weak adsorption of oxygen on transition metal oxide catalysts limits the improvement of their electrocatalytic oxygen reduction reaction (ORR) performance. Herein, a dopamine-assisted method is developed to prepare Mn-doped ceria supported on nitrogen-doped carbon nanotubes (Mn-Ce-NCNTs). The morphology, dispersion of Mn-doped ceria, composition, and oxygen vacancies of the as-prepared catalysts were analyzed using various technologies. The results show that Mn-doped ceria was formed and highly dispersed on NCNTs, on which oxygen vacancies are abundant. The as-prepared Mn-Ce-NCNTs exhibit a high ORR performance, on which the average electron transfer number is 3.86 and the current density is 24.4% higher than that of commercial 20 wt % Pt/C. The peak power density of Mn-Ce-NCNTs is 68.1 mW cm-2 at the current density of 138.9 mA cm-2 for a Zn-air battery, which is close to that of 20 wt % Pt/C (69.4 mW cm-2 at 106.1 mA cm-2). Density functional theory (DFT) calculations show that the oxygen vacancy formation energies of Mn-doped CeO2(111) and pure CeO2(111) are -0.55 and 2.14 eV, respectively. Meanwhile, compared with undoped CeO2(111) (-0.02 eV), Mn-doped CeO2(111) easily adsorbs oxygen with the oxygen adsorption energy of only -0.68 eV. This work provides insights into the synergetic effect of Mn-doped ceria for facilitating oxygen adsorption and enhancing ORR performance.

A Quick Joule‐Heating Coupled with Solid‐Phase Synthesis for Carbon‐Supported Pd–Se Nanoparticles Toward High‐Efficiency Electrocatalysis

AbstractWith respect to the potential of palladium (Pd)‐based nanomaterials in catalyzing typical electrochemical reactions, herein, a strategy that couples the quick Joule‐heating with a solid phase synthesis for producing carbon‐supported Pd–Se nanoparticles with welcome features is reported, e.g., fine sizes, clean surfaces, and controlled crystal phases toward electrocatalysis of oxygen reduction reaction (ORR) and ethanol oxidation reaction (EOR) in an alkaline medium. Principally, the introduction of Se into Pd alters its electronic properties and weakens the adsorption of key reaction intermediates on the Pd–Se nanoparticles during the ORR and EOR process, thus endowing them with better electrocatalysis for the same electrochemical reactions. Impressively, the carbon‐supported Pd–Se nanoparticles exhibit phase‐dependent electrocatalysis toward ORR and EOR. In particular, the cubic Pd17Se15 nanoparticles supported on carbon substrate show mass activity of 0.206 A mgPd−1 and specific activity of 0.546 mA cm−2 at 0.9 V for ORR in 0.1 m KOH electrolyte, while the orthorhombic PdSe2 nanoparticles show a mass activity of 3.79 A mgPd−1 for EOR, higher than that of their cubic counterpart and commercial Pd/C catalyst. The universality of this synthetic strategy in manufacturing carbon‐supported noble metal chalcogenide nanoparticles and highlighting its potential in designing highly efficient electrocatalysts are emphasized.

ZIF-8 derived iron-, sulphur-, and nitrogen-doped catalysts for anion-exchange membrane fuel cell application

This study presents the preparation of tridoped Fe, N, S carbon-based catalysts using ZIF-8 as the main carbon source and iron(II)acetate, 1,10-phenanthroline, ammonia gas and thiourea as precursors for Fe, N and S elements. Thiourea was mixed via planetary ball-milling with a Fe–N–C catalyst prepared by inert gas pyrolysis, and different pyrolysis conditions were applied thereafter. The main goal of the work is to synthesise active non-precious metal electrocatalysts for oxygen reduction reaction (ORR). High electrocatalytic ORR activity in alkaline media was observed for the two materials obtained after thiourea addition and subsequent pyrolysis. Physico-chemical characterisation revealed successful S- and N-doping for all three catalysts with enhanced porosity for the two materials that were subjected to additional pyrolysis after the thiourea addition. The sulphur doping was highest for the FeNSC3 material that was subjected to a second pyrolysis in N2 and a third pyrolysis in NH3, compared to the FeNSC2 material that was subjected to a single pyrolysis in NH3 flow after thiourea addition. The ORR activity of FeNSC2 with half-wave potential of 0.88 V was slightly higher than that of FeNSC3, and the former was selected for evaluation as a cathode catalyst in an anion-exchange membrane fuel cell.

Sulfur poisoned PtNi/C catalysts toward two-electron oxygen reduction reaction for acidic electrosynthesis of hydrogen peroxide

Selective electrocatalysis of two-electron oxygen reduction reaction (2e– ORR) has been recognized as a sustainable and on-site process for hydrogen peroxide (H2O2) production. Great progress has been achieved for 2e– ORR in alkaline media. However, it is challenged by insufficient activity and selectivity of the catalysts in acidic electrolytes. Herein, we report sulfur-poisoned PtNi/C catalysts (PtNiSx/C) that could regulate ORR from the 4e– to 2e– pathway. The identified PtNiS0.6/C offers high activity in terms of onset potential of ∼0.69 V (vs. RHE) and ∼80 % selectivity. The mass activity is also comparable and outperforms representative Pt-based precious and transition-metal-based catalysts. In addition, it is interestingly found that the Faradaic efficiency further increased to 95 % during the long-term electrolysis test due to Ni atom surface migration. The electrochemical production of the H2O2 system was applied to the electro-Fenton process, which has realized the effective degradation of organic pollutants. This work offers a strategy by sulfur poisoning PtNi/C catalyst to realize Pt-based 2e– ORR active catalysts to electrolysis of H2O2 in acidic media.

Pore size modulation of cobalt-corrole-based porous organic polymers for boosted electrocatalytic oxygen reduction reaction

The highly active and selective oxygen reduction reaction (ORR) is vital to promote the performance of advanced energy conversion systems, such as fuel cells and other electrochemical devices. Porous framework materials have the capability to combine the catalytic performance of catalytic active units with their porous characteristics, making them promising oxygen reduction catalysts. However, due to the difficulty in designing and synthesizing catalytic active units, the pore size modulation of framework materials is primarily achieved by altering the linkers. We herein report the design and synthesis of three cobalt-corrole-based porous organic polymers (Co-POP-1, Co-POP-2 and Co-POP-3) with different pore sizes, which were obtained by extending 5,15-meso substituents of Co corroles. Compared to Co-POP-1 and Co-POP-2, Co-POP-3 has the largest pore size. Benefiting from the enhanced mass transfer and the highly exposed active sites, Co-POP-3 displayed remarkably boosted activity for the selective four-electron/four-proton (4e−/4 H+) ORR with a half-wave potential of E1/2 = 0.89 V versus reversible hydrogen electrode (RHE) in 0.1 M KOH solutions. This work not only presents a cobalt-corrole-based porous organic polymer catalyst with high ORR activity and selectivity but also provides a new strategy to moderate the pore size of porous framework materials.

Synthesis of PtNi Nanoparticles to Accelerate the Oxygen Reduction Reaction.

We report the synthesis of core-shell Ni-Pt nanoparticles (NPs) with varying degrees of crystallographic facets and surface layers rich in Pt via a seed-mediated thermolytic approach. Mixtures of different surfactants used during synthesis resulted in preferential surface passivation, which in turn dictated the size, chemical composition, and geometric evolution of these PtNi NPs. Electrochemical investigations of these pristine core-shell Ni-Pt structures in the oxygen reduction reaction (ORR) show that their catalytic functionalities outperform the commercial Pt/C reference catalyst. The enhanced electrocatalytic ORR performances of these Pt-based PtNi NPs are correlated with the weakened oxygen binding strength or surface-adsorbed hydroxyl (OH) species on active Pt surface sites induced by the downshift of the d-band center as a result of compressive strain effects. Our studies offer a robust synthetic approach for the development of core-shell nanostructures for enhanced ORR catalysis.

In-Situ Nanoarchitectonics of Fe/Co LDH over Cobalt-Enriched N-Doped Carbon Cookies as Facile Oxygen Redox Electrocatalysts for High-Rate Rechargeable Zinc-Air Batteries.

The reality of long-term rechargeable and high-performance zinc-air batteries relies majorly on cost-effective and eminent bifunctional electrocatalysts, which can perform both the oxygen reduction reaction (ORR) and the oxygen evolution reaction (OER). Herein, we demonstrate a new approach for the synthesis of in-situ-grown layered double hydroxide of iron and cobalt over a cobalt nanoparticle-enriched nitrogen-doped carbon frame (CoL 2:1) by a simple coprecipitation reaction with facile scale-up and explore its electrocatalytic ORR and OER activity for an electrically rechargeable zinc-air battery. Consequently, the developed composite displays excellent ORR and OER activity with an ORR half-wave potential of 0.84 V, a limiting current density of 5.85 mA/cm2, and an OER overpotential of 320 mV with exceptional stability. The outstanding bifunctionality index of the catalyst (ΔE = 0.72 V) inspired us to utilize it as a cathode catalyst in an in-house developed prototype zinc-air battery. The battery could easily supply a specific capacity of 804 mAh/g with a maximum peak power density of 161 mW/cm2. The battery exhibits an attractive charge-discharge profile with a lesser voltage gap of 0.76 V at 10 mA/cm2 with durability for a period of 200 h and a voltage efficiency of 97%, which surpassed the corresponding Pt/C + RuO2-based zinc-air battery. Further, a maximum load of 50 mA/cm2 could easily be sustained during cycling, revealing its outstanding stability. A series-connected two CoL 2:1-based zinc-air batteries effortlessly enlighten a pinwheel fan and LED panel simultaneously, revealing its practicality. The high electrical conductivity and greater specific surface area of Co/N-C and its robust attachment with Fe/Co LDH preserves both active sites, thereby resulting in exceptional performance. Our method is capable of being flexible enough to create various bifunctional Co/N-C-based composite electrodes, opening up a feasible pathway to rechargeable zinc-air batteries with maximum energy density.

Tuning Electrocatalytic Oxygen Reduction Reaction with Dynamic Control of Electrochemical Interfaces.

Herein, we report the tuning of the activity and selectivity of the oxygen reduction reaction (ORR) through the dynamic regulation of the electrochemical interfaces to surpass the performance of conventional electrocatalysis. This is achieved by applying an oscillating potential between the ORR operating potential and anion adsorbing potential on a gold electrode. Oscillating potential enhances the selectivity for H2O2 by up to 1.35 times compared to the static potential, as confirmed by rotating ring-disk electrode and fluorescence assay measurements. We showed that the enhanced selectivity depends on dynamic adsorption and desorption of anions, and the enhancement occurs in the millisecond time scale or shorter. The transient selectivity to H2O2 can reach ∼97% within the first 5 ms after potential switching. Our results suggest that the dynamic interface can create a transient but unique microenvironment for new reactivity that cannot be reproduced under static conditions, which offers a new dimension in controlling electrocatalysis.

Roles of Oxygen-Containing Functional Groups in Carbon for Electrocatalytic Two-Electron Oxygen Reduction Reaction.

Recent years have witnessed great research interests in developing high-performance electrocatalysts for the two-electron (2e-) oxygen reduction reaction (ORR) that enables the sustainable and flexible synthesis of H2O2. Carbon-based electrocatalysts exhibit attractive catalytic performance for the 2e- ORR, where oxygen-containing functional groups (OFGs) play a decisive role. However, current understanding is far from adequate, and the contribution of OFGs to the catalytic performance remains controversial. Therefore, a critical overview on OFGs in carbon-based electrocatalysts toward the 2e- ORR is highly desirable. Herein, we go over the methods for constructing OFGs in carbon including chemical oxidation, electrochemical oxidation, and precursor inheritance. Then we review the roles of OFGs in activating carbon toward the 2e- ORR, focusing on the intrinsic activity of different OFGs and the interplay between OFGs and metal species or defects. At last, we discuss the reasons for inconsistencies among different studies, and personal perspectives on the future development in this field are provided. The results provide insights into the origin of high catalytic activity and selectivity of carbon-based electrocatalysts toward the 2e- ORR and would provide theoretical foundations for the future development in this field.

Advanced Hollow Cubic FeCo-N-C Cathode Electrocatalyst for Ultrahigh-Power Aluminum-Air Battery.

The exploration of electrocatalysts toward oxygen reduction reaction (ORR) is pivotal in the development of diverse batteries and fuel cells that rely on ORR. Here, a FeCo-N-C electrocatalyst (FeCo-HNC) featuring with atomically dispersed dual metal sites (Fe-Co) and hollow cubic structure is reported, which exhibits high activity for electrocatalysis of ORR in alkaline electrolyte, as evidenced by a half-wave potential of 0.907V, outperforming that of the commercial Pt/C catalyst. The practicality of such FeCo-HNC catalyst is demonstrated by integrating it as the cathode catalyst into an alkaline aluminum-air battery (AAB) paring with an aluminum plate serving as the anode. This AAB demonstrates an unprecedented power density of 804mWcm-2 in ambient air and an impressive 1200mWcm-2 in an oxygen-rich environment. These results not only establish a new benchmark but also set a groundbreaking record for the highest power density among all AABs reported to date. Moreover, they stand shoulder to shoulder with state-of-the-art H2-O2 fuel cells. This AAB exhibits robust stability with continuous operation for an impressive 200 h. This groundbreaking achievement underscores the immense potential and forward strides that the present work brings to the field.

Ceria-modified palladium-based catalysts as high-performance electrocatalysts for oxygen reduction and formic acid oxidation

Recently, a primary challenge hindering the commercialization of direct fuel cells is the development of robust nonplatinum electrocatalysts to improve the performance of the oxygen reduction reaction (ORR) and formic acid oxidation reaction (FAOR). In this paper, polyol reduction and high temperature calcination carbonization were used to improve the conductivity of the catalyst by the modification of rare earth Ce. Pd has similar properties to Pt, with one-fifth of the properties of Pt, and the rare earth elements have low electronegativity, making it easy to supply electrons and fill Pd's antibonding orbitals. Rare Earth elements effectively enhance ORR activity by making palladium more metallic. The high-activity, low-cost and high-stability electrocatalytic ORR and FAOR catalysts PdxCe/C were designed. After a series of testing methods, the physical properties and electrochemical properties were characterized, and the optimum structure and composition were selected. The stability of the catalyst with the optimal structure and composition was assessed, and it was applied to various composite batteries to verify its capability in practical application.

Boron in the Second Coordination Sphere of Fe Single Atom Boosts the Oxygen Reduction Reaction.

Metal single atoms coordinated with four nitrogen atoms (M1N4) are regarded as tremendously promising catalysts for the electrocatalytic oxygen reduction reaction (ORR). Nevertheless, the strong bond intensity between the metal center and the O atom in oxygen-containing intermediates significantly limits the ORR activity of M1N4. Herein, the catalytically active B atom is successfully introduced into the second coordination sphere of the Fe single atom (Fe1N4-B-C) to realize the alternative binding of B and O atoms and thus facilitate the ORR activity. Compared with the pristine Fe1N4 catalyst, the synthesized Fe1N4-B-C catalyst exhibits improved ORR catalytic capability with a half-wave potential (E1/2) of 0.80 V and a kinetic current density (JK) of 5.32 mA cm-2 in acid electrolyte. Moreover, in an alkaline electrolyte, the Fe1N4-B-C catalyst displays remarkable ORR activity with E1/2 of 0.87 V and JK of 8.94 mA cm-2 at 0.85 V, outperforming commercial Pt/C. Notably, the mechanistic study has revealed that the active center is the B atom in the second coordination shell of the Fe1N4-B-C catalyst, which avoids the direct bonding of Fe-O. The B center has a moderate binding force to the ORR intermediate, which flattens the ORR energy diagram and thereby improves the ORR performance. Therefore, this study offers a novel strategy for tailoring catalytic performance by tuning the active center of single-atom catalyst.

High-entropy engineering with regulated defect structure and electron interaction tuning active sites for trifunctional electrocatalysis

High-entropy alloy nanoparticles (HEANs) possessing regulated defect structure and electron interaction exhibit a guideline for constructing multifunctional catalysts. However, the microstructure-activity relationship between active sites of HEANs for multifunctional electrocatalysts is rarely reported. In this work, HEANs distributed on multi-walled carbon nanotubes (HEAN/CNT) are prepared by Joule heating as an example to explain the mechanism of trifunctional electrocatalysis for oxygen reduction, oxygen evolution, and hydrogen evolution reaction. HEAN/CNT excels with unmatched stability, maintaining a 0.8V voltage window for 220 h in zinc-air batteries. Even after 20 h of water electrolysis, its performance remains undiminished, highlighting exceptional endurance and reliability. Moreover, the intrinsic characteristics of the defect structure and electron interaction for HEAN/CNT are investigated in detail. The electrocatalytic mechanism of trifunctional electrocatalysis of HEAN/CNT under different conditions is identified by in situ monitoring and theoretical calculation. Meanwhile, the electron interaction and adaptive regulation of active sites in the trifunctional electrocatalysis of HEANs were further verified by density functional theory. These findings could provide unique ideas for designing inexpensive multifunctional high-entropy electrocatalysts.

Hybrid high-performance oxygen reduction reaction Fe–N–C electrocatalyst for anion exchange membrane fuel cells

Atomically dispersed active sites and hierarchical porosity in Fe–N–C catalyst materials are essential for efficient oxygen reduction reaction (ORR) electrocatalysis and effective mass transport, respectively. However, the majority of these catalysts fail to deliver outstanding electrocatalytic activity and stumble when used as cathode materials in fuel cells. Herein, we developed a catalyst with partially transformed metallic Fe into Fe-Nx sites embedded in the carbonaceous matrix, and its excellent electrocatalytic performance is attributed to the hybrid nanoparticles and built-in Fe-Nx site structures. The optimized Fe@Fe–N–C catalyst was tested for ORR performance both ex-situ using the rotating (ring)-disk electrode technique and in an anion exchange membrane fuel cell (AEMFC). The Fe@Fe–N–C electrocatalyst exhibited remarkably enhanced ORR activity in alkaline media with a half-wave potential of 0.822 V vs. reversible hydrogen electrode (RHE) and showed the maximum power density (Pmax) of 242 mW cm−2 in an AEMFC test, surpassing the peak power density obtained from the Pt/C cathode catalyst (Pmax = 220 mW cm−2) under H2–O2 conditions. Therefore, the study provides a promising prospect for designing improved, cost-effective, and noble metal-free electrocatalysts for achieving high performance in AEMFCs.