Electrical Resistivity Measurements Research Articles

Saturated fatty acids differently affect mitochondrial function and the intestinal epithelial barrier depending on their chain length in the in vitro model of IPEC-J2 enterocytes.

Introduction: Maintenance of the intestinal barrier mainly relies on the mitochondrial function of intestinal epithelial cells that provide ATP through oxidative phosphorylation (OXPHOS). Dietary fatty acid overload might induce mitochondrial dysfunction of enterocytes and may increase intestinal permeability as indicated by previous in vitro studies with palmitic acid (C16:0). Yet the impact of other dietary saturated fatty acids remains poorly described. Methods: To address this question, the in vitro model of porcine enterocytes IPEC-J2 was treated for 3days with 250µM of lauric (C12:0), myristic (C14:0), palmitic (C16:0) or stearic (C18:0) acids. Results and discussion: Measurement of the transepithelial electrical resistance, reflecting tight junction integrity, revealed that only C16:0 and C18:0 increased epithelial permeability, without modifying the expression of genes encoding tight junction proteins. Bioenergetic measurements indicated that C16:0 and C18:0 were barely β-oxidized by IPEC-J2. However, they rather induced significant OXPHOS uncoupling and reduced ATP production compared to C12:0 and C14:0. These bioenergetic alterations were associated with elevated mitochondrial reactive oxygen species production and mitochondrial fission. Although C12:0 and C14:0 treatment induced significant lipid storage and enhanced fusion of the mitochondrial network, it only mildly decreased ATP production without altering epithelial barrier. These results point out that the longer chain fatty acids C16:0 and C18:0 increased intestinal permeability, contrary to C12:0 and C14:0. In addition, C16:0 and C18:0 induced an important energy deprivation, notably via increased proton leaks, mitochondrial remodeling, and elevated ROS production in enterocytes compared to C12:0 and C14:0.

Superconductivity of a new Ru-based alloy Ru3Sb1.75Sn5.25

We report the synthesis and superconductivity of a new Ru-based alloy Ru3Sb1.75Sn5.25. The single crystal and polycrystal samples were synthesized by the Sn-flux method and solid state reaction, respectively. The Ru3Sb1.75Sn5.25 crystals were characterized by powder X-ray diffraction, electrical resistivity, magnetic susceptibility, and specific heat measurements. We find Ru3Sb1.75Sn5.25 crystallize in the Ir3Ge7-type structure and exhibits superconductivity with onset transition temperature Tc = 4.2 K. Density functional theory calculation on Ru3Sb1.75Sn5.25 unveils multiple peaks of density of states around the Fermi level, which may explain the emergence of superconductivity. Our study provides an example compound to explore the fascinating interplay of superconductivity, electronic band structure and paramagnetism in Ru-based superconductors.

Densification and Surface Carbon Transformation of Diamond Powders under High Pressure and High Temperature.

A new type of poly-diamond plate without a catalyst was produced via the high-pressure high-temperature (HPHT) compression of diamond powders. The densification of diamond powders and sp3 to sp2 carbon on the surface under HPHT compression was investigated through the characterization of the microstructure, Raman spectroscopy analysis and electrical resistance measurement. The densification and sp3-sp2 transformation on the surface are mainly affected by the pressure, temperature and particle size. The quantitative analysis of the diamond sp3 and sp2 carbon amount was performed through the peak fitting of Raman spectra. It was found that finer diamond particles under a higher temperature and a lower pressure tend to produce more sp2 carbon; otherwise, they produce less. In addition, it is interesting to note that the local residual stresses measured using Raman spectra increase with the diamond particle size. The suspected reason is that the increased particle size reduces the number of contact points, resulting in a higher localized pressure at each contact point. The hypothesis was supported by finite element calculation. This study provides detailed and quantitative data about the densification of diamond powders and sp3 to sp2 transformation on the surface under HPHT treatment, which is valuable for the sintering of polycrystalline diamonds (PCDs) and the HPHT treatment of diamonds.

Suppression of spiking defects in deep penetration electron beam welded ETP copper

The electron beam is an appropriate tool to weld pure copper due to its high absorptivity on the copper surface, a high power density and inert vacuum environment. However, deep penetration electron beam welding of pure copper often produces the spiking defect. In this work bead on plate electron beam welding was done on Cu-ETP. A critical welding speed was determined for the distinction between a conduction-determined (at lower welding speed) and a non-conduction-determined welding speed range (at higher welding speed). The influence of high preheating temperatures was shown. The welds were investigated by light optical microscopy, electron backscatter diffraction measurements, ultrasonic testing, in situ thermal imaging, electrical resistance measurements and tensile tests. It was shown that in the conduction-determined welding speed regime without preheating, full and partial penetration welds exhibited root porosity. This effect was related to the overheating of the weld pool in combination with the phenomena causing spiking. Low defect root formation was achieved by using welding speeds greater than the critical value or by applying high preheating temperatures. The joints reached up to 98% of the international annealed copper standard in terms of specific electrical conductivity. Rupture took place within the joints during tensile tests. The joints exhibited up to 77% of the ultimate tensile strength of the base metal. Welds carried out with preheating exceeded the base metal regarding the fracture strain.

P037 Modelling gut complexity and disease: development of a next-generation adult stem cell based tubular gut-on-a-chip model

Abstract Background Developing effective therapies for Inflammatory Bowel Disease (IBD) necessitates advanced in vitro models that faithfully replicate the intricacies of the gut. The current challenge is to create models that encompass the 3D morphology, heterogeneity, and boundary characteristics of intestinal tissue while also being amenable to high-throughput screening. Microfluidic techniques are emerging as vital tools to introduce physiologically relevant cues into conventional cell cultures. Methods We present an innovative in vitro model employing human adult stem cell-derived colon organoids cultivated as perfused epithelial tubules within the MIMETAS OrganoPlate®. This microfluidic platform facilitates the simultaneous culture of up to 64 independent gut tubules on an extracellular matrix, offering continuous media perfusion without artificial membrane interference. The barrier function of the epithelial tubules is assessed in real-time through transepithelial electrical resistance (TEER) measurements. Immunostaining and 3D reconstruction of confocal images evaluate the expression of relevant epithelial markers. Results The tubular epithelial model of the intestinal tract demonstrated rapid cell polarization, expression of cell-specific markers, tight junction formation, and the presence of functional transporters. TEER measurements indicated functional and reproducible barrier integrity across tubules generated from different organoid donors for at least 10 days. Incorporation of additional cell types, such as patient-derived immune cells and endothelium, marks a groundbreaking advancement in understanding disease pathogenesis. The plug-and-play modularity of these models allows for flexibility in incorporating specific cell types based on the biological pathway of interest. Conclusion Our next-generation gut-on-a-chip model faithfully mimics the IBD phenotype and facilitates screening for potential drug targets. Combining adult human stem cell-derived intestinal organoids with microfluidic technology provides a robust platform to study physiology and disease mechanisms in patient-specific gut models. The inclusion of IBD patient-derived cells promises further refinement, enabling a more profound exploration of disease phenotypes and treatment responsiveness. Moreover, organoids, as one of the most physiologically relevant cell sources, authentically represent patient biology, enhancing the translational potential of our findings.

P1238 Exploring the Role of Klebsiella variicola and Klebsiella pneumoniae in Pediatric Ulcerative Colitis Pathogenesis

Abstract Background Recent studies indicated that Klebsiella (K) pneumoniae (isolated from the stool of IBD patients) and K. variicola (isolated from the mesenteric tissue of Crohn disease patients) have the potential to induce inflammation in epithelial and preadipocyte cells, exacerbating colitis in murine models. We isolated these strains from pediatric ulcerative colitis (UC) patients' appendix (relevant to UC pathogenesis given the protective effects of appendectomy) and other non-inflamed colon sections. We hypothesized that these isolates are invasive and induce inflammation in UC. These strains have not been previously studied in UC. Methods K. variicola and K. pneumoniae were isolated from two pediatric UC patients' appendices and other non-inflamed colon sections and identified using 16S DNA Sanger sequencing. Virulence of the two strains was determined by infecting Caco2 cell lines and performing adhesion and invasion assays, quantifying biofilm formation, and assessing barrier functions using transepithelial electrical resistance (TEER) measurement. Importantly, we monitored the production of pro-inflammatory (e.g., IL-8, TNF-α) and anti-inflammatory (IL-10) cytokines using reverse transcriptase quantitative polymerase chain reaction (RT-qPCR). Results K. variicola and K. pneumoniae exhibited high levels of biofilm formation compared to adherent-invasive Escherichia coli (AIEC), which are commonly isolated from IBD patients. Furthermore, the Klebsiella strains adhered to epithelial cells within 2-3 hours post infection. TEER experiments showed compromised barrier integrity after 6 hours and overnight infection. Except for K. pneumoniae isolated from the ascending colon, the tested strains exhibited a significant increase in IL-8 expression. Similarly, K. variicola from the peri-appendicular region demonstrated elevated TNF-α gene expression. Conclusion K. variicola and K. pneumoniae isolated from UC patients have the potential to form biofilms, disrupt barrier integrity, and trigger inflammatory responses. These findings unravel a potential role for pathogenic Klebsiella strains in driving UC pathogenesis. Importantly, these data shed light on the role of appendix-associated bacteria in the development of UC. Future work includes using comparative genomics to map the virulence determinants of these bacteria.

P1208 MH002, an optimized live biotherapeutic product, for the treatment of inflammatory bowel diseases, has mode-of-actions linked to restoration of intestinal dysbiosis, mucosal integrity, and immune homeostasis

Abstract Background MH002 is a live biotherapeutic product consisting of 6 well-characterized commensal strains, that is in clinical development for the treatment of Ulcerative Colitis (UC) and acute Pouchitis. Both are multifactorial disorders which occur through a combination of dysregulated host inflammatory mechanisms and interactions with gut microbiota. Methods Faecal slurries of 6 UC patients with active disease were prepared to inoculate a standardized in vitro gut model (SHIME®) which mimics the colon microbiome of patients. A total of 24 simulators were run for 8d, with a single dose administration of MH002 (human equivalent dose [HED] ~1) or vehicle on Day0. Butyrate production in the simulators was quantified daily and host response effects were assessed in in vitro cell-based assays using samples from Day1. Caco-2 cells were co-cultured with human peripheral blood mononuclear cells and treated for 48h with Day1 samples, followed by transepithelial electrical resistance (TEER) and cytokine measurements. Wound healing was assessed by imaging of monolayers of T84 cells, scratched and treated with Day1 samples. Furthermore, the effects of MH002 (daily, 24d, HED ~30) on disease activity index (DAI; body weight [BW], stool consistency, occult blood), local inflammation, and mucosal damage were evaluated in acute dextran sulfate sodium (DSS) induced colitis, when administered to C57BL/6 mice (15/group) as from 14d prior to DSS intake, and compared to 5-aminosalicylate (5-ASA; daily, 24d, 150mg/kg) and vehicle. Animals were euthanized in the acute (Day7; 10/group) and recovery phase (Day11; 5/group). Results In vitro administration of MH002 to patient-derived colonic microbiomes restored within 1d butyrate production and increased efficiency to improve epithelial barrier integrity, modulate T-cell-mediated immune responses, and promote mucosal wound healing in in vitro cell cultures (Table 1). DSS intake induced a significant decrease in relative BW and an increase in DAI. A significant recovery (BW, DAI, stool consistency) was observed at Day11 for MH002 and 5-ASA. Moreover, at Day11, macroscopic inflammation (colon weight/length ratio) and histologic scores were lower with MH002 and 5-ASA as compared to vehicle (Figure 1). Conclusion By restoring intestinal dysbiosis and epithelial integrity, and attenuating local inflammation, MH002 treatment should lead to lower disease activity and, ultimately, to clinical remission without immune suppression. Indeed, study MH002-UC-201 in mild-to-moderate UC was completed with favourable treatment effects (endoscopic improvement, faecal calprotectin normalization, improved stool consistency) and no safety concerns (Abstract Vermeire et al.; EudraCT 2020-004355-33).

Extrinsic n-type semiconductor transition in ZrSe2 with the metallic character through hafnium substitution

Two-dimensional (2D) layered materials exhibit versatile electronic properties in their different phases. The intrinsic electronic properties of these materials can be modulated through doping or intercalation. In this study, we investigated the electronic properties of Hf-doped ZrSe2 single crystals using angle-resolved photoemission spectroscopy (ARPES) combined with first-principles density functional theory (DFT) calculations. It is observed that the valence band maxima of ZrSe2, located below the Fermi level, undergo a significant change with the introduction of Hf substitution. Hf can introduce extra charges into the conduction band, rather than making a mixed structure of HfSe2 and ZrSe2 band structure, which can cross the Fermi level. Compared to the semiconducting band structure of ZrSe2, we observed that the conduction band crosses the Fermi level at the high symmetry M point in Hf-doped ZrSe2. This suggests an increase of electron-type carriers around the Fermi level, resulting in an extrinsic charge carrier density in the conduction band, which can form a metallic behaviour. It can be noticed that the Hf cations can create disorder in the form of excess atoms of Zr, which yields more carriers in the conduction band in the shape of “smeared bands”. The tails of the “smeared band” occupied the d-orbitals extended into the Fermi level and left the d-band below. Similarly, the electrical resistance measurements further confirm the metallic-like character of Hf-doped ZrSe2 compared to the semiconductor ZrSe2, indicating increased carriers. This metallic-like behavior is suggested to be predisposed by the extrinsic electrons induced by the substitutional disorder. This study further demonstrates the possibility of band gap engineering through heavy metal doping in 2D materials.

Optical transmission and photoconductivity of chemical bath-deposited CdS thin films for optoelectronic applications

This paper presents a comprehensive study of the optical transmission, photoconductivity, and morphology of CdS thin films deposited via the chemical bath deposition (CBD) method. The films deposited for 60 min exhibit an optical energy band gap value of 2.42 eV and the highest optical transmission of 75 % in the wavelength range of 500–900 nm. For these films, the transmission electron microscopy imaging shows a distribution of particle sizes around 10 nm. The wavelength dependence of the photoconductivity, extracted from photo resistivity data, shows that the maximum photoconductivity occurs at 492 nm wavelength. This corresponds to an electrical energy band gap of 2.52 eV, which is greater than the optically measured energy gap of 2.42 eV. Based on these results, the electron-hole pair binding energy for CdS films is estimated as 100 meV. According to the electrical resistivity vs. temperature measurements, the activation energy is 1.26 eV which agrees with the electrical energy band gap of 2.52 eV. CdS films annealed under nitrogen gas at 200 °C for one hour exhibited an energy gap of 2.32 eV. These films displayed a conductivity of 60 × 10−4 Scm−1, a carrier concentration of 6.38 × 1014 cm−3, and a mobility of 7.46 cm2 V−1 s−1. These impressive characteristics suggest the suitability of CBD-grown CdS films annealed at 200 °C in nitrogen gas, to be used as the window material in CdS/CdTe thin film solar cells and other optoelectronic applications.

Electrical resistivity, seismic velocity, and porosity of crustal rocks from the Oman ophiolite under brine-saturated ocean floor conditions

In order to examine the effects of crack properties on electrical resistivity and seismic velocity, we conducted simultaneous measurements of electrical resistivity, seismic velocity and porosity at brine-saturated hydrostatic pressures using mafic crustal rocks from the Oman ophiolite. The resistivity and velocity of the samples increase systematically with increasing confining pressure owing to the closure of cracks, as monitored by changes in porosity. Apparent formation factors of each sample are related to the porosity, but nonlinear relationships on logarithmic plots indicate that Archie's law cannot explain these experimental data. We evaluated the effect of crack porosity and aspect ratio for the measured velocity based on the effective medium theory, and the electrical resistivity was inferred from the crack porosity and connectivity according to the percolation model. The experimental velocity and resistivity results are consistent with the model calculations in terms of crack density, aspect ratio and connectivity. We applied a combined velocity-resistivity model to the geophysical logging and borehole data for the oceanic crust in Hole 504B. Our inversion results indicate that the seismic layer 2/3 transition is primarily caused by an alteration front controlled by interconnected cracks and fluid flow in the oceanic crust.

HIV-1 gp120 amplifies astrocyte elevated gene-1 activity to compromise the integrity of the outer blood-retinal barrier.

This study aims to investigate the functions and mechanistic pathways of Astrocyte Elevated Gene-1 (AEG-1) in the disruption of the blood-retinal barrier (BRB) caused by the HIV-1 envelope glycoprotein gp120. We utilized ARPE-19 cells challenged with gp120 as our model system. Several analytical techniques were employed to decipher the intricate interactions at play. These included PCR, Western blot, and immunofluorescence assays for the molecular characterization, and transendothelial electrical resistance (TEER) measurements to evaluate barrier integrity. We observed that AEG-1 expression was elevated, whereas the expression levels of tight junction proteins ZO-1, Occludin, and Claudin5 were downregulated in gp120-challenged cells. TEER measurements corroborated these findings, indicating barrier dysfunction. Additional mechanistic studies revealed that the activation of NFκB and MMP2/9 pathways mediated the AEG-1-induced barrier destabilization. Through the use of lentiviral vectors, we engineered cell lines with modulated AEG-1 expression levels. Silencing AEG-1 alleviated gp120-induced downregulation of tight junction proteins and barrier impairment while concurrently inhibiting the NFκB and MMP2/9 pathways. Conversely, overexpression of AEG-1 exacerbated these pathological changes, further compromising the integrity of the BRB. Gp120 upregulates the expression of AEG-1 and activates the NFκB and MMP2/9 pathways. This in turn leads to the downregulation of tight junction proteins, resulting in the disruption of barrier function.

High-pressure phase diagram of Bi-Ga: Polymorphism, anomalous melting curves and liquid miscibility gap

The high-pressure states of the elements can significantly impact the phase diagrams of their alloys due to polymorphism in the solid state and anomalies and slope changes in the melting curve. Here, we investigate the effect of these characteristics on a model system, the Bi-Ga system, by constructing a thermodynamic model of the high-pressure phase diagram and validating the proposed transitions by electrical resistance measurements in a ‘Paris-Edinburgh’ press. We achieve conclusive agreement between our calculated phase diagram up to 6 GPa and the measured transitions. At higher pressures, the liquid miscibility gap in this system disappears, and the phase diagram changes from a monotectic to a eutectic type at a pressure of 8 GPa. We also measured the monotectic temperature and the liquidus of Bi-rich alloy that presents anomalous behavior as a function of pressure. The present contribution demonstrates the crucial contribution of the high-pressure behavior of the elements in characterizing the challenging and complex behavior of alloys under pressure.

Absence of superconductivity in I4/mmm-FeH5: experimental evidence.

The experimentally discovered FeH5 exhibits a structure built of atomic hydrogen that only has bonding between hydrogen and iron atoms [C. M. Pepin, G. Geneste, A. Dewaele, M. Mezouar and P. Loubeyre, Science, 2017, 357, 382]. However, its superconductivity has remained unsolved since its discovery. In this work, we have synthesized I4/mmm-FeH5 at 139 GPa combined with laser-heating conditions. The electrical resistance measurements at ultrahigh pressures indicate that no evidence of superconducting transition of FeH5 is observed in the temperature range of 1.5 K to 270 K. These results indicate that I4/mmm-FeH5 does not exhibit superconductivity within the experimental temperature range, and the introduction of iron atoms is not beneficial to the formation of the superconducting phase.

Exploring the degradation of silver nanowire networks under thermal stress by coupling in situ X-ray diffraction and electrical resistance measurements.

The thermal instability of silver nanowires (AgNWs) leads to a significant increase of the electrical resistance of AgNW networks. A better understanding of the relationship between the structural and electrical properties of AgNW networks is primordial for their efficient integration as transparent electrodes (TEs) for next-generation flexible optoelectronics. Herein, we investigate the in situ evolution of the main crystallographic parameters (i.e. integrated intensity, interplanar spacing and peak broadening) of two Ag-specific Bragg peaks, (111) and (200), during a thermal ramp up to 400 °C through in situ X-ray diffraction (XRD) measurements, coupled with in situ electrical resistance measurements on the same AgNW network. First, we assign the (111) and (200) peaks of χ-scans to each five crystallites within AgNWs using a rotation matrix model. Then, we show that the thermal transition of bare AgNW networks occurs within a temperature range of about 25 °C for the electrical properties, while the structural transition spans over 200 °C. The effect of a protective tin oxide coating (SnO2) on AgNW networks is also investigated through this original in situ coupling approach. For SnO2-coated AgNW networks, the key XRD signatures from AgNWs remain constant, since the SnO2 coating prevents Ag atomic surface diffusion, and thus morphological instability (i.e. spheroidization). Moreover, the SnO2 coating does not affect the strain of both (111) and (200) planes. The thermal expansion for bare and SnO2-coated AgNW networks appears very similar to the thermal expansion of bulk Ag. Our findings provide insights into the underlying failure mechanisms of AgNW networks subjected to thermal stress, helping researchers to develop more robust and durable TEs based on metallic nanowire networks.

Monitoring Intestinal Organoid-Derived Monolayer Barrier Functions with Electric Cell-Substrate Impedance Sensing (ECIS).

The measurement of transepithelial electrical resistance across confluent cell monolayer systems is the most commonly used technique to study intestinal barrier development and integrity. Electric cell substrate impedance sensing (ECIS) is a real-time, label-free, impedance-based method used to study various cell behaviors such as cell growth, viability, migration, and barrier function in vitro. So far, the ECIS technology has exclusively been performed on cell lines. Organoids, however, are cultured from tissue-specific stem cells, which better recapitulate cell functions and the heterogeneity of the parent tissue than cell lines and are therefore more physiologically relevant for research and modeling of human diseases. In this protocol paper, we demonstrate that ECIS technology can be successfully applied on 2D monolayers generated from patient-derived intestinal organoids. Key features • We present a protocol that allows the assessment of various cell functions, such as proliferation and barrier formation, with ECIS on organoid-derived monolayers. • The protocol facilitates intestinal barrier research on patient tissue-derived organoids, providing a valuable tool for disease modeling.

Charge carrier transport in PbS films doped with iodine.

The results of the measurements of electrical and Hall resistivities on polycrystalline PbS films doped with iodine obtained through hydrochemical deposition are presented. The analysis of the temperature dependence of resistivity points out the crossover from the hopping mechanism due to thermal delocalization in the impurity band to the variable range hopping mechanism. The increase in the iodine content in the films leads to an increase in the impurity ionization energy. It has been established that the temperature dependence of resistivity over a wide temperature range obeys the inverse Arrhenius law, which is characteristic of disordered polycrystalline films with different sizes and orientations of crystallites relative to the substrate, as confirmed by AFM topography, Raman spectra and X-ray diffraction measurements. We found that the type of charge carrier changes from electrons to holes with an increase in the iodine content. Additionally, for a wide range of iodine doping, the concentration of charge carriers is low, indicating the possible occurrence of a self-compensation mechanism due to the formation of impurity defects.

Colon-available mango (poly)phenols exhibit mitigating effects on the intestinal barrier function in human intestinal cell monolayers under inflammatory conditions.

This study investigated the impact of in vivo available colon-mango (poly)phenols on stress-induced impairment of intestinal barrier function. Caco-2/HT29-MTX cells were incubated with six extracts of ileal fluid collected pre- and 4-8 h post-mango consumption before being subjected to inflammatory stress. (Poly)phenols in ileal fluids were analysed by UHPLC-HR-MS. Epithelial barrier function was monitored by measurement of trans-epithelial electrical resistance (TEER) and the production of selected inflammatory markers (interleukin-8 (IL-8) and nitric oxide (NO)) and the major mucin of the mucosal layer (MUC2). Post-mango intake ileal fluids contained principally benzoic acids, hydroxybenzenes and galloyl derivatives. There was a high interindividual variability in the levels of these compounds, which was reflected by the degree of variability in the protective effects of individual ileal extracts on inflammatory changes in the treated cell cultures. The 24 h treatment with non-cytotoxic doses of extracts of 4-8 h post-mango intake ileal fluid significantly reduced the TEER decrease in monolayers treated with the inflammatory cytomix. This effect was not associated with changes in IL-8 expression and secretion or claudine-7 expression. The mango derived-ileal fluid extract (IFE) also mitigated cytomix-dependent nitrite secretion, as a proxy of NO production, and the MUC2 reduction observed upon the inflammatory challenge. These insights shed light on the potential protective effect of mango (poly)phenols on the intestinal barrier exposed to inflammatory conditions.

Study of the metallome and transcriptome of a degenerating cellular model of the retinal pigment epithelium

Aims/Purpose: To study the changes on the metallome and transcriptome of a cellular model of the retinal pigment epithelium (RPE) during its in vitro degeneration after 4 months in culture.Methods: Primary cultures of human fetal RPE cells were established in P12 transwell inserts and cultured for 4 months. Cell pigmentation and barrier function was followed up using optical microscopy and measurement of the transepithelial electrical resistance (TEER). Samples were collected at 21, 91 and 133 days in culture and analysed for gene expression, metal homeostasis of Ca, Na, P, Mg and P, and extracellular deposit formation through RNA sequencing (RNA‐Seq), elemental mass spectrometry (ICP‐MS) and immunocytochemistry assays, respectively.Results: RPE cells formed a differentiated monolayer at 21 days in culture, expressing specific genes and proteins of RPE and giving increasing TEER values. However, after 133 days in culture, loss of tight junction proteins (i.e. CLDN19 and BEST1) and electrical resistance was seen, together with loss of pigmentation and increase of apolipoprotein E deposition in the extracellular space. Gene expression analysis showed an enrichment on apoptotic processes, biomolecule phosphorylation, and signs of epithelial‐to‐mesenchymal transition (EMT). Degeneration of RPE cells concurred with an increase of Na and P content in the cytosol and decrease of Mg, while a decrease of Mg, P and Cu was determined in the insoluble fraction of cells. Time‐dependent changes of metals were accompanied with the alteration of metal transporters and antioxidant enzymes using metals as cofactors.Conclusions: Degeneration of RPE cells in culture was characterized by depigmentation of cells, improper barrier function, downregulation of antioxidant protection, loss of epithelial phenotype, and changes on the levels of Na, P, Mg and Cu, as well as of the expression of their homeostatic proteins.

A novel “microbiota-host interaction model” to study the real-time effects of fermentation of non-digestible carbohydrate (NDCs) on gut barrier function

In this study, an in vitro co-culture model using an electric cell-substrate impedance sensing system (ECIS) for testing the impact of real-time fermentation of non-digestible carbohydrates (NDCs) by the intestinal microbiota on gut barrier function was established. We applied Lactobacillus plantarum WCFS1 as a model intestinal bacterium and alginate-pectin as immobilization polymers as well as a source of NDCs to determine the impact of pectin fermentation on the barrier function of T84 gut epithelial cells. In the first design, L. plantarum WCFS1 was encapsulated in an alginate capsule followed by embedding in an agar layer to mimic a firm mucus layer that might be present in the colon. In this experimental design, the presence of the agar layer interfered with the transepithelial electrical resistance (TEER) measurement of T84 cells. Subsequently, we removed the agar layer and used encapsulated bacteria in an alginate gel and found that the TEER measurement was adequate. The encapsulation of the L. plantarum WCFS1 does avoid direct contact with cells. Also, the encapsulation system allows higher amounts of packing densities of L. plantarum WCFS1 in a limited space which can limit the oxygen concentration within the capsule and therefore create anaerobic conditions. To test this design, T84 cells were co-incubated with L. plantarum alginate-capsules supplemented with graded loads of fermentable pectin (0, 4, and 8 mg/ml per capsule) to investigate the effect of pectin fermentation on gut barrier function. We observed that as the pectin content in the L. plantarum capsules increased, pectin showed a gradually stronger protective effect on the TEER of the gut epithelium. This could partly be explained by enhanced SCFA production as both lactate and acetate were enhanced in L. plantarum containing alginate capsules with 8 mg/ml pectin. Overall, this newly designed in vitro co-culture model allows for studying the impact of bacteria-derived fermentation products but also for studying the direct effects of NDCs on gut barrier function in a relatively high-throughput way.

Innovative electrode and chip designs for transendothelial electrical resistance measurements in organs-on-chips.

Many different epithelial and endothelial barriers in the human body ensure the proper functioning of our organs by controlling which substances can pass from one side to another. In recent years, organs-on-chips (OoC) have become a popular tool to study such barriers in vitro. To assess the proper functioning of these barriers, we can measure the transendothelial electrical resistance (TEER) which indicates how easily ions can cross the cell layer when a current is applied between electrodes on either side. TEER measurements are a convenient method to quantify the barrier properties since it is a non-invasive and label-free technique. Direct integration of electrodes for TEER measurements into OoC allows for continuous monitoring of the barrier, and fixed integration of the electrodes improves the reproducibility of the measurements. In this review, we will give an overview of different electrode and channel designs that have been used to measure the TEER in OoC. After giving some insight into why biological barriers are an important field of study, we will explain the theory and practice behind measuring the TEER in in vitro systems. Next, this review gives an overview of the state of the art in the field of integrated electrodes for TEER measurements in OoC, with a special focus on alternative chip and electrode designs. Finally, we outline some of the remaining challenges and provide some suggestions on how to overcome these challenges.