Measurements Of Electrical Properties Research Articles

Electric Response of a Negative Dielectric Anisotropy Nematic Liquid Crystal Doped with Ionic Dopant

The electrical properties measurements have been performed in a homogeneous alignment parallelepiped cell containing 4-methoxy benzylidene- 4-butylaniline (MBBA) liquid crystal doped with 0.02%wt tetrabutylammonium bromide (TBAB). The measurement of the complex permittivity was conducted in the nematic phase, covering a frequency range of 42 Hz to 5 MHz. A new relaxation mode was observed in the low-frequency region, which was not present in pure MBBA. The obtained dielectric dispersion could be fitted using the double Cole–Cole formula to determine the relaxation frequencies. The steady-state current exhibited a nonlinear dependence on the applied voltage, and hysteresis was observed in the transient current-voltage characteristic curve.

Alkaline-Responsive, Self-Healable, and Conductive Copolymer Composites with Enhanced Mechanical Properties Tailored for Wearable Tech.

Despite significant advancements, current self-healing materials often suffer from a compromise between mechanical robustness and functional performance, particularly in terms of conductivity and responsiveness to environmental stimuli. Addressing this issue, the research introduces a self-healable and conductive copolymer, poly(ionic liquid-co-acrylic acid) (PIL-co-PAA), synthesized through free radical polymerization, and further optimized by incorporating thermoplastic polyurethane (TPU). This combination leverages the unique properties of each component, especially ion-dipole interactions and hydrogen bonds, resulting in a material that exhibits exceptional self-healing abilities and demonstrates enhanced mechanical properties and electrical conductivity. Moreover, the PIL-co-PAA/TPU films showcase alkaline-responsive behavior, a feature that broadens their applicability in dynamic environments. Through systematic characterization, including thermogravimetric analysis, tensile testing, and electrical properties measurements, the mechanisms behind the improved performance and functionality of these films are elucidated. The conductivities and ultimate tensile strength (σuts) of the PIL-co-PAA/TPU films regain 80% under 8h healing process. To extend the applications for wearable devices, the self-healing properties of commercial cotton fabrics coated with the self-healable PIL-co-PAA are also investigated, demonstrating both self-healing and electrical properties. This study advances the understanding of self-healable conductive polymers and opens new avenues for their application in wearable technology.

Graphene-Doped Piezoelectric Transducers by Kriging Optimal Model for Detecting Various Types of Laryngeal Movements.

This study fabricated piezoelectric fibers of polyvinylidene fluoride (PVDF) with graphene using near-field electrospinning (NFES) technology. A uniform experimental design table U*774 was applied, considering weight percentage (1-13 wt%), the distance between needle and disk collector (2.1-3.9 mm), and applied voltage (14.5-17.5 kV). We optimized the parameters using electrical property measurements and the Kriging response surface method. Adding 13 wt% graphene significantly improved electrical conductivity, increasing from 17.7 µS/cm for pure PVDF to 187.5 µS/cm. The fiber diameter decreased from 21.4 µm in PVDF/1% graphene to 9.1 µm in PVDF/13% graphene. Adding 5 wt% graphene increased the β-phase content by 6.9%, reaching 65.4% compared to pure PVDF fibers. Material characteristics were investigated using scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction analysis (XRD), contact angle measurements, and tensile testing. Optimal parameters included 3.47 wt% graphene, yielding 15.82 mV voltage at 5 Hz and 5 N force (2.04 times pure PVDF). Force testing showed a sensitivity (S) of 7.67 log(mV/N). Fibers were attached to electrodes for piezoelectric sensor applications. The results affirmed enhanced electrical conductivity, piezoelectric performance, and mechanical strength. The optimized piezoelectric sensor could be applied to measure physiological signals, such as attaching it to the throat under different conditions to measure the output voltage. The force-to-voltage conversion facilitated subsequent analysis.

Thermochromic properties and surface chemical states of reactive magnetron sputtered vanadium oxide thin films at various deposition pressures

Vanadium oxide thin films were prepared using reactive magnetron sputtering method, varying the deposition pressures from 4 to 10 mTorr while maintaining the other sputtering parameters constant. Our investigations revealed sensitive dependence of deposition pressure, chemical states of the V and O atoms, crystal phases, and thermochromic (TC) optical modulation. Specifically, the film deposited at 8 mTorr displayed distinct TC characteristics with a prevalent monoclinic m-VO2 phase according to X-ray diffraction (XRD), supported by X-ray photoelectron spectroscopy (XPS). Optical transmittance modulation and electrical property measurements revealed a metal–insulator transition (MIT), confirming the intimate connection between TC characteristics and presence of the m-VO2 phase. Films deposited at pressures lower or higher than 8 mTorr exhibited typical semiconductor behavior without TC characteristics, further supported by in situ XRD, where (110) plane shifted to lower angle upon heating above τC. Chemical state analysis by XPS revealed a clear correlation between V−O peaks and the presence of a VO2 phase, with the film deposited at 8 mTorr displaying relatively large peak fitted area indicative of the VO2 phase. These findings highlight the critical and sensitive dependence of the deposition conditions in tailoring the properties of vanadium oxide thin films and provide valuable insights for potential applications in chromogenic films.

Data ‐Driven Long‐Term Energy Efficiency Prediction of Dielectric Elastomer Artificial Muscles

AbstractThe widespread adoption of dielectric elastomer actuators (DEAs) as compliant artificial muscle is on the horizon after a wide range of prototype demonstrations. The next step is to accelerate the material optimization for specific design requirements. This work proposes a data‐driven framework to predict long‐term DEA energy consumption and efficiency using measurements of initial electrical properties. DEA datasets are generated from 242 pre‐stretched single‐layer actuators and 53 multi‐layer bending actuators actuated for 30–180min. Devices are made with different elastomer and electrode materials, and tested with a novel instrument that can measure multiple aspects of DEA actuation. First, experiments are conducted to develop an empirical understanding of the electro‐mechanical energy conversion mechanism and the impact of material choices during DEA actuation. Second, data‐driven models are applied to the datasets to predict energy consumption and efficiency. Third, the potential generalization of this approach is investigated by using transfer learning strategies to predict energy efficiency at 100 min with as little as 1 min of input data. Moreover, it is found that linear regression can extend the prediction up to 180 min. Additionally, transfer learning is applied to predict energy‐related properties of multi‐layer DEAs using a small dataset. The proposed data‐driven framework can evolve into an intelligent system for accelerating new material discovery by predicting performance and providing device optimization strategies.

Direct Visualization of Defect-Controlled Diffusion in van der Waals Gaps.

Diffusion processes govern fundamental phenomena such as phase transformations, doping, and intercalation in van der Waals (vdW) bonded materials. Here, the diffusion dynamics of W atoms by visualizing the motion of individual atoms at three different vdW interfaces: hexagonal boron nitride (BN)/vacuum, BN/BN, and BN/WSe2, by recording scanning transmission electron microscopy movies is quantified. Supported by density functional theory (DFT) calculations, it is inferred that in all cases diffusion is governed by intermittent trapping at electron beam-generated defect sites. This leads to diffusion properties that depend strongly on the number of defects. These results suggest that diffusion and intercalation processes in vdW materials are highly tunable and sensitive to crystal quality. The demonstration of imaging, with high spatial and temporal resolution, of layers and individual atoms inside vdW heterostructures offers possibilities for direct visualization of diffusion and atomic interactions, as well as for experiments exploring atomic structures, their in situ modification, and electrical property measurements of active devices combined with atomic resolutionimaging.

Measurement of through-thickness electrical properties of carbon fiber reinforced thermoplastics using transmission method based on electromagnetic induction testing

In this study, we proposed an electromagnetic induction testing method for measuring the electrical properties of carbon fiber reinforced thermoplastics (CFRTPs) along the through-thickness direction. The effectiveness of the transmission method, wherein the coil is placed opposite to the object to be measured, was demonstrated through finite element analysis and experimental measurements. The simulation results indicated that the output voltage of an interlaminar non-electrically conductive specimen exceeded that of an interlaminar conductive specimen due to the electromagnetic shielding effect. In the experiments, the impedance along the through-thickness direction depended on the lamination configuration and the presence of the PA-6 layer. Our findings indicate that the proposed method can be used to measure the changes in the electrical properties of CFRTP along the through-thickness direction.

Interface Structures on Mechanically Polished Surface of Spinel Ferrite and Its Effect on the Magnetic Domains.

Soft magnetic spinel ferrites are indispensable parts in devices such as transformers and inductors. Mechanical surface processing is a necessary step to realize certain shapes and surface roughness in producing the ferrite but also has a negative effect on the magnetic properties of the ferrite. In the past few years, a new surface layer was always believed to form during the mechanical surface processing, but the change of atomic structure on the surface and its effect on the magnetic structure remain unclear. Herein, an interface structure consisting of a rock-salt sublayer, distorted NiFe2O4 sublayer, and pristine NiFe2O4 was found to form on mechanically polished single-crystal NiFe2O4 ferrite. Such an interface structure is produced by phase transformation and lattice distortion induced by the mechanical processing. The magnetic domain observation and electrical property measurement also indicate that the magnetic and electrical anisotropy are both enhanced by the interface structure. This work provides deep insight into the surface structure evolution of spinel ferrite by mechanical processing.

Oxygen diffusion coefficients in ferroelectric hafnium zirconium oxide thin films

Oxygen diffusion coefficients in the metastable ferroelectric phase of polycrystalline hafnium zirconium oxide (HZO) thin films have been quantified using 18O tracers and time-of-flight secondary ion mass spectrometry. 11.5 nm thick HZO films containing 16O were deposited by plasma-enhanced atomic layer deposition followed by post-metallization annealing to crystallize into the ferroelectric phase. A 1.2 nm thick HZO layer containing 18O was then deposited using thermal atomic layer deposition with H218O as a reactant. Thermal anneals were conducted at 300, 350, and 400 °C and the ferroelectric phase confirmed after the anneals by x-ray diffraction, infrared spectroscopy, and electrical property measurements. 18O depth profiles were measured and fit with a thin film diffusion equation to determine the oxygen diffusion coefficients. Oxygen diffusion coefficients ranged from approximately 2 × 10−18 cm2/s at 300 °C to 5 × 10−17 cm2/s at 400 °C with an activation energy of 1.02 ± 0.24 eV.

Measurement of Extracellular Electrical Properties with Tracer-Based MRI

Measurement of Extracellular Electrical Properties with Tracer-Based MRI

Investigation of Nondestructive and Noncontact Electrical Characterization of GaN Thin Film on ScAlMgO4 Substrate Using Terahertz Time‐Domain Spectroscopic Ellipsometry with Characteristic Impedance Analytical Model

Semiconductor evaluation methods frequently require sample processing and carry the risk of defects and property changes. Therefore, nondestructive and noncontact electrical property measurement techniques are necessary. Terahertz time‐domain spectroscopic ellipsometry (THz‐TDSE) can simultaneously estimate the electrical properties and film thickness of a sample. However, whether this method can simultaneously determine electrical properties and film thickness for semiconductor thin films of 1 μm or less remains unclear. This study uses THz‐TDSE to evaluate the electrical properties and film thickness of a GaN thin film (≈0.8 μm thick) on a ScAlMgO4 substrate. Using the conventional analysis based on Fresnel's formula (FR model), which is used in the field of optics, uniquely determining the electrical properties and film thickness is not possible owing to multiple optimal solutions. Therefore, a model combining the characteristic impedance model used in the radio‐wave region with the FR model is employed in the analysis. The obtained values of electrical properties of the GaN thin film evaluated using THz‐TDSE are consistent with those using Hall effect measurement. Moreover, the film thickness is consistent with that measured from the cross‐sectional transmission electron microscopy observation.

Influence of design and annealing parameters on measurements of AC properties of NiFe-SiO2 multilayer structures

In this article, due to the exceptionally interesting electrical and magnetic properties of nanocomposites, which include ferromagnetic materials in a dielectric matrix, multilayer NiFe-SiO2 nanocomposites were obtained. The entire sequence of technological processes using magnetron sputtering equipment in the presence of argon was presented, the aim of which was to create structures with different numbers and thicknesses of layers, as well as in two measurement configurations. Measurements of AC electrical properties were carried out in a variable temperature range, i.e. from room temperature to 373 K, using the 4-point method. The obtained measurement results were compared in terms of design parameters, such as thickness and number of layers, as well as technological parameters, such as heating duration. Structural analysis was performed using scanning electron microscopy (SEM) to investigate the effect of oxidation on the multilayer structures and to confirm the granular structure of the nanocomposite. Additionally, the chemical composition of the obtained multilayers was examined using Energy-dispersive X-ray spectroscopy (EDX). Resistive parameters were tested in the range of magnetic field induction from 0 T to 0.3 T. Based on the conductivity relationships, it was proven that a hopping mechanism of current conduction occurs in the tested samples. Using the frequency dependencies of the phase shift angle, it is possible to adjust the equivalent RC electronic circuit, thereby determining the potential application of the tested materials.

The ferroelectric and piezoelectric properties of (Hf1−x Ce x )O2 films on indium tin oxide/Pt/TiO x /SiO2/(100)Si substrates obtained using a no-heating radio-frequency magnetron sputtering deposition method

The effect of composition and film thickness on the ferroelectric and piezoelectric properties of (Hf1−x Ce x )O2 films deposited without substrate heating was investigated. (Hf1−x Ce x )O2 films with various x values (x = 0.07–0.27) and thickness (150–880 nm) were deposited via RF magnetron sputtering on indium tin oxide (ITO)/Pt/TiO x /SiO2/(100)Si substrates. The crystalline phases of the films were observed by X-ray diffraction. The measurements of electrical properties revealed ferroelectric phases in the x range of 0.11–0.21. The film with x = 0.16 exhibited the maximum remanent polarization (Pr) of 15 μC cm−2, as well as the highest effective piezoelectric coefficient. In addition, the ferroelectric and structural properties remained almost unchanged with increasing film thickness. Therefore, the no-heating deposition of ferroelectric (Hf1−x Ce x )O2 films and their phase stability with respect to thickness were demonstrated in this study. This work provides a pathway for the deposition of ferroelectric (Hf1−x Ce x )O2 films on flexible, wearable sensors.

Fabrication of Gadolinium Oxide-doped Fe2O3-LaFeO3-La2O3 Thick Films by Screen Printing Technique and Their Electrical Properties for Ethanol Gas Sensors

Recently, there have been many researchers who discussed screen printing techniques (SPT) as a good approach to fabricate the thick films for gas sensor applications. In this work, the SPTs were conducted to fabricate the thick films based on gadolinium oxide-doped Fe2O3-LaFeO3-La2O3 that were applied as ethanol gas sensors. The crystal and morphological structures were investigated using x-ray diffraction and scanning electron microscopy, respectively. It shows that there are three phases of the crystal structure of gadolinium oxide-doped Fe2O3-LaFeO3-La2O3 i.e., rhombohedral, orthorhombic, and hexagonal. The morphological structure shows an average particle size of about 0.61 μm. Furthermore, the electrical properties measurements were explored to ensure the performance of thick films in detecting the ethanol gases. Th measurements were conducted in the range of temperature of about 310 ∘C to 325 ∘C and in the various ethanol gas containing, it is 0 ppm, 100 ppm, 200 ppm, and 300 ppm. This result showed that the highest response of thick films in the existence of ethanol gases (300 ppm) is 427 with an optimum temperature of 319 ∘C. It is also confirmed that SPT has an excellent approach in thick film fabrication to produce gas sensor devices with good performance.
 Keywords: fabrication, gadolinium oxide, doped, thick films, screen printing, electrical properties, ethanol, sensors

Design of Electrical Sheet Resistance of Thin Film Measurement System Based on GM Cryocooler in Cryogenic Temperature

The determination of the dependencies of the electrical resistivity of the thin film to temperature is of great importance both for understanding the conduction mechanism and for numerous technical applications of these films. In this work, to characterize, the electrical properties of thin films, a GM cryocooler-based automatic board temperature range electrical properties measurement system has been constructed. The system can measure multiple samples simultaneously. The cooling process was simulated using the time-discrete differencing to validate the optimized device design parameters and minimize heat losses. Furthermore, the temperature-dependent sheet resistance results were compared with the results from the physical property measurement system.

An Inductive Method for Comprehensive Estimation of Temperature-Dependent Electrical and Thermal Properties of Conductive Ferromagnetic Materials

Reliable information about the properties of the processed materials has a significant impact on the effects of their processing. In induction heating processes, this also applies to information about the influence of temperature T on these properties. These are both thermal and electro-magnetic properties. Based on previous studies, a comprehensive experimental method is presented for estimating the temperature characteristics of thermal diffusivity, volumetric heat capacity and resistivity on one measurement station, with particular attention to ferromagnetic materials. The estimation process is carried out on an induction heating stand using forcing signals from an inverter generator. In a computer-controlled cycle that changes the base temperature level, basic measurements of thermal and electrical properties are carried out on a material sample in the form of a cylindrical disk. They are the results of the analysis of the temperature and electromagnetic responses of a material sample to short- and long-term step pulses of a sinusoidal excitation signal with a frequency of approximately 40 kHz. The presented estimation method can be treated as a final method or a preliminary procedure for radically narrowing the variability in decision variables inthe optimization process of simultaneous determination of the sought material characteristics.

Effect of co‐substitution on complex thermoelectric compounds: The Zintl phase Ba1‐xSrxZn2‐yCuySb2 system

AbstractThree co‐substituted quaternary and quinary Zintl phases belonging to the Ba1‐xSrxZn2‐yCuySb2 (x = 0, 0.09; 0.24 ≤ y ≤ 0.42) system were prepared by the molten Pb metal‐flux method. Co‐substitution using the cationic Sr and anionic Cu for Ba and Zn was initially applied to lower the thermal conductivities and to improve the electric conductivities of these title compounds simultaneously. The homogeneities of single‐phase products were verified by powder x‐ray diffraction analysis, and the BaCu2S2‐type orthorhombic crystal structures with the Ba/Sr and the Zn/Cu mixed‐sites were refined by single crystal x‐ray diffraction analysis. Structural selectivity for the observed BaCu2S2‐type phase was rationalized by the radius ratio of cationic and anionic elements, where r+/r− > 1. DFT calculations using the three structural models revealed that the Sr and Cu substitutions can increase the structural stability and the hole carrier concentration. A series of temperature‐dependent electrical transport property measurements for BaZn1.76Cu0.24Sb2 and Ba0.91Sr0.09Zn1.70Cu0.30Sb2 successfully proved that the co‐substitution using Sr and Cu enhanced electrical conductivities, but reduced the Seebeck coefficients resulting in the slight change in power factor.

ZnSb Films on Flexible Substrates: Stability, Optical Bandgap, Electrical Properties, and Indium Doping

AbstractUndoped and In‐doped ZnSb thin films are deposited on rigid glass and flexible polyimide (Kapton) by physical vapor deposition. Detailed structural and chemical characterization is performed along with measurement of electrical and optical properties. These properties are very similar for films on glass and Kapton. Flexible ZnSb films show remarkable stability of electrical and optical properties, which are unchanged after 104 cycles of linear bending with surface strain 0.18%. Only severe flexing after this treatment (torsional bending with surface strain 1.7%) causes progressive degradation of conductivity over tens to hundreds of cycles. The ZnSb optical direct gap is determined to be 0.89 ± 0.05 eV. The optical direct gap of β Zn4Sb3 was 1.07 ± 0.05 eV. Other absorption features in the films, including smaller indirect gaps, are discussed.

Infrared Signatures for Phase Identification in Hafnium Oxide Thin Films.

Phase identification in HfO2-based thin films is a prerequisite to understanding the mechanisms stabilizing the ferroelectric phase in these materials, which hold great promise in next-generation nonvolatile memory and computing technology. While grazing-incidence X-ray diffraction is commonly employed for this purpose, it has difficulty unambiguously differentiating between the ferroelectric phase and other metastable phases that may exist due to similarities in the d-spacings, their low intensities, and the overlapping of reflections. Infrared signatures provide an alternative route. However, their use in phase identification remains limited because phase control has overwhelmingly been accomplished via substituents, thereby convoluting infrared signatures between the substituents and the phase changes that they induce. Herein, we report the infrared optical responses of three undoped hafnium oxide films where annealing conditions have been used to create films consisting primarily of the ferroelectric polar orthorhombic Pca21, antipolar orthorhombic Pbca, and monoclinic P21/c phases, as was confirmed via transmission electron microscopy (TEM), UV-visible optical properties, and electrical property measurements. Vibrational signatures acquired from synchrotron nano-Fourier transform infrared spectroscopy (nano-FTIR) are shown to be capable of differentiating between the phases in a nondestructive, rapid, and nanoscale manner. The utility of nano-FTIR is illustrated for a film exhibiting an antiferroelectric polarization response. In this sample, it is proven that this behavior results from the Pbca phase rather than the often-cited tetragonal phase. By demonstrating that IR spectroscopy can unambiguously distinguish phases in this material, this work establishes a tool needed to isolate the factors dictating the ferroelectric phase stability in HfO2-based materials.

Unveiling the effect of Gd3+ doping on enriching the structural, magnetic, optical, and dielectric properties of biocompatible hematite nanoparticles

This work is an attempt to obtain gadolinium-doped hematite GdxFe2−xO3 (x = 0, 0.05, and 0.1) using the hydrothermal method followed by heat treatment. The work also studies the impact of gadolinium doping on the magnetic, electrical, and optical properties of hematite. X-ray diffraction (XRD) analysis, energy-dispersive X-ray spectroscopy (EDAX) and photoelectron spectroscopy (XPS) showed that the obtained phase for all samples was pure hematite with no evidence of secondary phases, indicating a high solubility limit of gadolinium ions in hematite lattice. The morphology and size distribution of the particles were investigated using high-resolution transmission electron microscopy (HRTEM) and scanning electron microscopy (SEM). It was found that the lattice parameters increased with increasing gadolinium concentration. Magnetization was not enhanced whereas, the coercivity decreased considerably. From UV–Vis diffuse reflection spectroscopy (DRS) measurements, the band gap energies of pure and doped α-Fe2O3 decreased from 2.01 to 1.94 eV respectively. Moreover, measurements of electrical properties showed that the dielectric permittivity decreased while the resistivity increased with increasing the gadolinium content. In addition, sulforhodamine B (SRB) test against oral epithelial cell lines showed low cytotoxicity of the particles. Finally, gadolinium doped hematite is introduced as a novel, environmentally benign material for potential applications in various fields including photocatalysis for water treatment, biosensor and as an antibacterial agent.