Efficient Oxygen Reduction Reaction Research Articles

Anodic degradation of salicylic acid and simultaneous bio-electricity recovery in microbial fuel cell using waste-banana-peels derived biochar-supported MIL-53(Fe)-metal-organic framework as cathode catalyst

This research was aimed to synthesize waste banana peel biochar (BC) supported MIL-53(Fe) metal–organic framework (MOF) (MIL-53(Fe)/BC) as an efficient cathode catalyst for application in a microbial fuel cell (MFC) for the treatment of salicylic acid (SA)-laden wastewater. This investigation marks the first application of such a catalyst in a MFC for SA degradation. The results revealed an increment in power density of MFC-MIL-53(Fe)/BC by 2.34-folds (142.2 ± 1.5 mW/m2) as compared to MFC-MIL-53(Fe) (60.6 ± 1.8 mW/m2). Removal of chemical oxygen demand in MFC-MIL-53(Fe)/BC (93.8 ± 2.2 %) was found to be comparable to MFC-Pt/C (94.6 ± 1.5 %). The MFC-MIL-53(Fe)/BC demonstrated a 91.5 ± 2.0 % biodegradation of SA. The power recovery per unit cost by MFC-MIL-53(Fe)/BC was found to be 380.21 mW/US$, which is significantly higher than MFC-Pt/C (6.08 mW/US$), indicating that MIL-53(Fe)/BC could be an affordable replacement to pricey Pt as cathode catalyst for efficient oxygen reduction reaction.

Facile and fast fabrication of CuCo alloy and N-codoped hierarchical porous carbon catalyst for efficient oxygen reduction reaction in microbial fuel cells

Designing a low-cost, high-performance oxygen reduction reaction (ORR) catalyst to replace the precious metal catalyst remains a huge challenge for microbial fuel cells (MFCs). Herein, a facile and rapid approach to fabricate highly active N-doped hierarchical porous carbon (NHPC) supported bimetal CuCo/NHPC composites with densely accessible active sites is developed by pyrolysis of Cu-doped ZIF-67 (CuCo-ZIF) precursor. In which, CuCo-ZIF precursor is synthesized through a one-pot hydrothermal method. Results showed that in addition to create additional Cu-Nx sites and increase N content, the Cu doping induces a hierarchical porous structure CuCo/NHPC composite with pores centered around 2.4, 4.2 nm and 10–60 nm, which can significantly accelerate the mass/electron transfer and improve efficient utilization of the active sites. The resulting CuCo/NHPC composite provides abundant active sites, high content of pyridinic-N and graphitic-N, which significantly boosts ORR performances. The CuCo/NHPC-T with pyrolysis temperature of 800 °C achieves remarkable ORR activity with low charge transfer resistances, high half-wave potential. The MFC assembled with CuCo/NHPC-800 (774.2 mW·m−2 and 0.713 V) significantly outperforms MFC assembled with Co-NC-800 (541.9 mW·m−2 and 0.583 V) in terms of maximum power density and open-circuit voltage. Moreover, the output voltage of MFC assembled with CuCo/NHPC-800 exhibited no significant downward trend within 30 days, which was better than that of Pt/C catalyst. This work provides a feasible time-saving route to develop promising nitrogen-enriched mesoporous carbon bimetallic ORR catalysts.

P-block germanenes as a promising electrocatalysts for the oxygen reduction reaction.

The oxygen reduction reaction (ORR), a pivotal process in hydrogen fuel cells crucial for enhancing fuel cell performance through suitable catalysts, remains a challenging aspect of development. This study explores the catalytic potential of germanene on Al (111), taking advantage of the successful preparation of stable reconstructed germanene layers on Al (111) and the excellent catalytic performance exhibited by germanium-based nanomaterials. Through first-principles calculations, we demonstrate that the O2molecule can be effectively activated on both freestanding and supported germanene nanosheets, featuring kinetic barriers of 0.40 and 0.04eV, respectively. The presence of the Al substrate not only significantly enhances the stability of the reconstructed germanene but also preserves its exceptional ORR catalytic performance. These theoretical findings offer crucial insights into the substrate-mediated modulation of germanene stability and catalytic efficiency, paving the way for the design of stable and efficient ORR catalysts for future applications.

Study of the Suitability of Corncob Biochar as Electrocatalyst for Zn–Air Batteries

There has been a recent increasing interest in Zn–air batteries as an alternative to Li-ion batteries. Zn–air batteries possess some significant advantages; however, there are still problems to solve, especially related to the tuning of the properties of the air–cathode which should carry an inexpensive but efficient bifunctional oxygen reduction (ORR) and oxygen evolution (OER) reaction electrocatalyst. Biochar can be an alternative, since it is a material of low cost, it exhibits electric conductivity, and it can be used as support for transition metal ions. Although there is a significant number of publications on biochars, there is a lack of data about biochar from raw biomass rich in hemicellulose, and biochar with a small number of heteroatoms, in order to report the pristine activity of the carbon phase. In this work, activated biochar has been made by using corncobs. The biomass was first dried and minced into small pieces and pyrolyzed. Then, it was mixed with KOH and pyrolyzed for a second time. The final product was characterized by various techniques and its electroactivity as a cathode was determined. Physicochemical characterization revealed that the biochar had a hierarchical pore structure, moderate surface area of 92 m2 g−1, carbon phase with a relatively low sp2/sp3 ratio close to one, and a limited amount of N and S, but a high number of oxygen groups. The graphitization was not complete while the biochar had an ordered structure and contained significant O species. This biochar was used as an electrocatalyst for ORR and OER in Zn–air batteries where it demonstrated a satisfactory performance. More specifically, it reached an open-circuit voltage of about 1.4 V, which was stable over a period of several hours, with a short-circuit current density of 142 mA cm−2 and a maximum power density of 55 mW cm−2. Charge–discharge cycling of the battery was achieved between 1.2 and 2.1 V for a constant current of 10 mA. These data show that corncob biochar demonstrated good performance as an electrocatalyst in Zn–air batteries, despite its low specific surface and low sp2/sp3 ratio, owing to its rich oxygen sites, thus showing that electrocatalysis is a complex phenomenon and can be served by biochars of various origins.

Enhanced catalytic performance of M-doped SnS2 (M: Ni, Cu, Fe, and Co) and graphene nanocomposite for oxygen reduction reaction in alkaline media

In this study, the electrocatalytic behavior of tin sulfide doped with various metallic elements (copper, cobalt, nickel, and iron) for the oxygen reduction reaction was investigated. Our findings reveal cobalt as the most effective dopant in enhancing ORR efficiency. The graphene nanosheets were introduced to form a G/Co-SnS2 nanocomposite, which significantly improved ORR performance, surpassing Pt/C in current density. Our findings underscore the positive impact of chemical doping and the synergistic effect of SnS2 with graphene nanosheets, improving the onset potential and facilitating the ORR. Through comprehensive characterization including XRD, XPS, FESEM, and BET analysis, the structural and surface properties of the materials were evaluated. Employing the Rotating Disk Electrode technique, we observed that G/Co-SnS2 exhibited a superior onset potential of 0.88 V vs. RHE and high current density of 6.12 mA cm−2, indicating enhanced ORR facilitation. Furthermore, Electrochemical Impedance Spectroscopy revealed lower resistance in the G/Co-SnS2 nanocomposite compared to other samples, highlighting its enhanced durability. Additionally, G/Co-SnS2 nanocomposite demonstrated significantly enhanced durability in comparison to the costly Pt/C catalyst, further underscoring its potential as a robust alternative for catalyzing the oxygen reduction reaction. These comprehensive characterizations provide insights into the enhanced electrocatalytic performance observed. Overall, this study highlights the promising potential of Co-doped SnS2 in combination with graphene nanosheets for efficient oxygen reduction reactions, opening avenues for advanced electrocatalytic materials in energy applications.

Nitrogen-bridged Cu-Zn dual-atom cooperative interface sites for efficient oxygen reduction reaction in Zn-air battery

Developing nonprecious catalysts with excellent behaviors for oxygen reduction reaction (ORR) has assumed considerable importance, but remains an arduous issue. Herein, we demonstrate a Kirkendall effect-pyrolysis (KEP) strategy to construct N-bridged Cu-Zn dual-atom supported on hollow N-doped carbon (Cu-Zn DA/HNC) for ORR. The hollow structure of N-doped carbon facilitates mass transfer and exposes more actives. What’s more, the shared N atom between Cu and Zn atoms is beneficial to enhance their synergetic effect, creating an appropriately enhanced O* binding. The resulting Cu-Zn DA/HNC displays excellent ORR activity in an alkaline electrolyte, following a nearly four-electron pathway of ORR. Even employing Cu-Zn DA/HNC as the cathode in ZABs, Cu-Zn DA/HNC presents a long cycling life up to 910 h and robust low-temperature adaptability. The facile and straightforward fabrication plus the outstanding ORR performance of Cu-Zn DA/HNC endows its great potential as a significant candidate in practical applications of ZAB.

Inhibiting Demetalation of Fe─N─C via Mn Sites for Efficient Oxygen Reduction Reaction in Zinc-Air Batteries.

Demetalation caused by the electrochemical dissolution of metallic Fe atoms is a major challenge for the practical application of Fe─N─C catalysts. Herein, an efficient single metallic Mn active site is constructed to improve the strength of the Fe─N bond, inhibiting the demetalation effect of Fe─N─C. Mn acts as an electron donor inducing more delocalized electrons to reduce the oxidation state of Fe by increasing the electron density, thereby enhancing the Fe─N bond and inhibiting the electrochemical dissolution of Fe. The oxygen reduction reaction pathway for the dissociation of Fe─Mn dual sites can overcome the high energy barriers to direct O─O bond dissociation and modulate the electronic states of Fe─N4 sites. The resulting FeMn─N─C exhibits excellent ORR activity with a high half-wave potential of 0.92V in alkaline electrolytes. FeMn─N─C as a cathode catalyst for Zn-air batteries has a cycle stability of 700h at 25°C and a long cycle stability of more than 210h under extremely cold conditions at -40°C. These findings contribute to the development of efficient and stable metal-nitrogen-carbon catalysts for various energy devices.

Construction of Conjugated Organic Polymers for Efficient Photocatalytic Hydrogen Peroxide Generation with Adequate Utilization of Water Oxidation.

The visible-light-driven photocatalytic production of hydrogen peroxide (H2O2) is currently an emerging approach for transforming solar energy into chemical energy. In general, the photocatalytic process for producing H2O2 includes two pathways: the water oxidation reaction (WOR) and the oxygen reduction reaction (ORR). However, the utilization efficiency of ORR surpasses that of WOR, leading to a discrepancy with the low oxygen levels in natural water and thereby impeding their practical application. Herein, we report a novel donor-bridge-acceptor (D-B-A) organic polymer conjugated by the Sonogashira-Hagihara coupling reaction with tetraphenylethene (TPE) units as the electron donors, acetylene (A) as the connectors and pyrene (P) moieties as the electron acceptors. Notably, the resulting TPE-A-P exhibits a remarkable solar-to-chemical conversion of 1.65% and a high BET-specific surface area (1132 m2·g-1). Furthermore, even under anaerobic conditions, it demonstrates an impressive H2O2 photosynthetic efficiency of 1770 μmol g-1 h-1, exceeding the vast majority of previously reported photosynthetic systems of H2O2. The outstanding performance is attributed to the effective separation of electrons and holes, along with the presence of sufficient reaction sites facilitated by the incorporation of alkynyl electronic bridges. This protocol presents a successful method for generating H2O2 via a water oxidation reaction, signifying a significant advancement towards practical applications in the natural environment.

Heteroatom Sulfur-Modified ZIF-8 Derived Zn, N Co-Doped Carbon Nanocages as Highly Efficient ORR Catalysts for Zn-Air Batteries

Carbon-based electrocatalysts derived from zeolitic imidazolate framework-8 (ZIF-8) have garnered significant attention, owing to their structural advantages, high surface area, and tunable active sites. Herein, we report the synthesis of heteroatom sulfur (S) modified ZIF-8 derived carbon nanocages (ZnS@N/S-C) for oxygen electrocatalysis through self-assembly and two-step pyrolysis. The resultant ZnS@N/S-C exhibits catalytic activity towards oxygen reduction reaction (ORR) with high half-wave potential (0.86 V) and stability (91.4%), separately, which is comparable to or superior to Pt/C. Furthermore, the application of ZnS@N/S-C as a cathode for Zn-air batteries (ZABs) demonstrates performance metrics such as an open-circuit voltage of 1.407 V, a power density of 114.4 mW cm−2, and a specific capacity of 764.6 mAh gZn −1, etc surpassing Pt/C. The performance of ZnS@N/S-C can be attributed to the fact that the introduction of S significantly increases the specific surface area, pore volume, and defect extent of the catalyst, while optimizing the electronic structure and generating ZnS active nanocrystals. This work employs a simple sulfurization strategy to enhance the ORR activity of ZIF-8-derived Zn-based catalysts with fully filled 3d orbitals, providing guidance for the development of such materials.

Fullerene-metalloporphyrin co-crystal as efficient oxygen reduction reaction electrocatalyst precursor for Zn-air batteries

Fullerene-metalloporphyrin co-crystal as efficient oxygen reduction reaction electrocatalyst precursor for Zn-air batteries

N-P covalent bond regulation of mesoporous carbon-based catalyst for lowered oxygen reduction overpotential and enhanced zinc-air battery performance

Developing sustainable metal-free carbon-based electrocatalysts is essential for the deployment of metal-air batteries such as zinc-air batteries (ZABs), among which doping of heteroatoms has attracted tremendous interest over the past decade. However, the effect of the heteroatom covalent bonds in carbon matrix on catalysis was neglected in most studies. Here, an efficient metal-free oxygen reduction reaction (ORR) catalyst is demonstrated by the N-P bonds anchored carbon (termed N,P-C-1000). The N,P-C-1000 catalyst exhibits superior specific surface area of 1362 m2 g−1 and ORR activity with a half-wave potential of 0.83 V, close to that of 20 wt% Pt/C. Theoretical computations reveal that the p-band center for C-2p orbit in N,P-C-1000 has higher interaction strength with the intermediates, thus reducing the overall reaction energy barrier. The N,P-C-1000 assembled primary ZAB can attain a large peak power density of 121.9 mW cm−2 and a steady discharge platform of ∼1.20 V throughout 120 h. Besides, when served as the cathodic catalyst in a solid-state ZAB, the battery shows flexibility, conspicuous open circuit potential (1.423 V), and high peak power density (85.8 mW cm−2). Our findings offer a strategy to tune the intrinsic structure of carbon-based catalysts for improved electrocatalytic performance and shed light on future catalysts design for energy storage technologies beyond batteries.

Elaborate construction of honeycomb-like porous carbon with embedment of N-doped carbon nanotubes as efficient electrocatalyst for zinc-air battery

Devising the synthesis strategy and uncovering the evolution mechanism of carbon-based materials are critical to the development of efficient oxygen reduction reaction (ORR) electrocatalysts for renewable energy storage systems. This study reports a hierarchical ORR electrocatalyst, Co@N-CNTs/3DHC, which features ultrafine cobalt nanoparticles embedded in nitrogen-doped carbon nanotubes (Co@N-CNTs) and Co@N-CNTs firmly anchored in the nano-chambers of a three-dimensional honeycomb-like porous carbon (3DHC). The synthesis strategy of Co@N-CNTs/3DHC involves the initial construction of a precursor, followed by controllable pyrolysis step. Based on detailed analysis of both evolved gases and carbonized products of precursors, the evolution mechanism of Co@N-CNTs/3DHC is specifically proposed. Prompted by the electron reconfiguration, extensive reaction interface and fast mass-transfer pathway, the as-synthesized hierarchical Co@N-CNTs/3DHC displays superior ORR activity in alkaline media (0.88 V of half-wave potential) compared to commercial Pt/C. Impressively, zinc-air battery equipped with Co@N-CNTs/3DHC cathode presents outstanding discharge voltage and exceptional stability. This work highlights a unique perspective on the synthesis strategy and growth mechanism of Co@N-CNTs@3DHC toward creation of hierarchical 3D carbon-based composite for advanced electrochemical energy devices.

Core-shell Co-NC@NC nanomaterial for efficient oxygen reduction reaction

Transition metal and nitrogen doped carbons (M-N-C) catalysts present significant potential as substitutes for platinum-carbon (Pt/C) in catalyzing oxygen reduction reaction (ORR). Hence, we employ an epitaxial growth strategy to prepare Zn/Co-ZIF@ZIF-8 crystals with core-shell structure. Subsequent pyrolysis and acid etching produce highly porous cobalt-doped nitrogen materials for ORR investigation. The resulting Co-NC@NC catalyst demonstrates a graded porous structure alongside remarkable conductivity, possessing a specific surface area measuring 623 m2 g−1. It showcases heightened ORR activity with a half-wave potential (E1/2) of 0.886 V, superior kinetic performance (illustrated by an extremely low Tafel slope measuring 45.98 mV/dec), and strengthened stability (with mere 25 mV day after 40,000 cycles) when contrast with Pt/C catalysts in 0.1 M KOH. Additionally, it exhibits notable activity and stability in acidic environments. These remarkable attributes are attributable to the graded structure, which facilitates rapid mass transfer, a high electrochemically active area that exposes highly dispersed active sites, and a conductive carbon skeleton network that promotes electron transfer.

Cobalt/nitrogen doped hollow carbon sphere-bamboo like carbon nanotube for highly efficient oxygen reduction reaction

The exploration of non-Pt catalysts with high electrocatalytic activity and durability is especially important for cathodic oxygen reduction reaction (ORR) in fuel cell. Here, cobalt and nitrogen doped hollow carbon sphere-bamboo like carbon nanotube (Co/NHCS-BCNT) is prepared by using SiO2 sphere as sacrificial template. Co nanoparticles are confined in the cavity and top end of the in-situ formed BCNT, which can not only avoid the agglomeration of Co nanoparticles but also inhibit corrosion in caustic electrolyte. The synergistic effect between NHCS and well-dispersed Co particles makes Co/NHCS-BCNT have superior catalytic activity toward ORR. The electrochemical surface area (ECSA) of Co/NHCS-BCNT is 222 cm2, which is higher than those of NHCS (164 cm2) and HCS (135 cm2). The onset potential and half-wave potential of Co/NHCS-BCNT are 0.941 V and 0.814 V, respectively, which are close to commercial Pt/C (0.949 V, 0.807 V). The Tafel slope of Co/NHCS-BCNT (63.8 mV dec-1) is lower than that of Pt/C (71.7 mV dec-1). In addition, Co/NHCS-BCNT shows excellent durability and fuel selectivity.

Tailoring Zirconia Supported Intermetallic Platinum Alloy via Reactive Metal-Support Interactions for High-Performing Fuel Cells.

Developing efficient and anti-corrosive oxygen reduction reaction (ORR) catalysts is of great importance for the applications of proton exchange membrane fuel cells (PEMFCs). Herein, we report a novel approach to prepare metal oxides supported intermetallic Pt alloy nanoparticles (NPs) via the reactive metal-support interaction (RMSI) as ORR catalysts, using Ni-doped cubic ZrO2 (Ni/ZrO2) supported L10-PtNi NPs as a proof of concept. Benefiting from the Ni migration during RMSI, the oxygen vacancy concentrations in the support are increased, leading to an electron enrichment of Pt. The optimal L10-PtNi-Ni/ZrO2-RMSI catalyst achieves remarkably low mass activity (MA) loss (17.8 %) after 400,000 accelerated durability test cycles in a half-cell and exceptional PEMFC performance (MA=0.76 A mgPt -1 at 0.9 V, peak power density=1.52/0.92 W cm-2 in H2-O2/-air, and 18.4 % MA decay after 30,000 cycles), representing the best reported Pt-based ORR catalysts without carbon supports. Density functional theory (DFT) calculations reveal that L10-PtNi-Ni/ZrO2-RMSI requires a lower energetic barrier for ORR than L10-PtNi-Ni/ZrO2 (direct loading), which is ascribed to a decreased Bader charge transfer between Pt and *OH, and the improved stability of L10-PtNi-Ni/ZrO2-RMSI compared to L10-PtNi-C can be contributed to the increased adhesion energy and Ni vacancy formation energy within the PtNi alloy.

Regulating the surface Pt coordination environment in the PtN overlayers on PtCuN hollow nanospheres for efficient oxygen reduction reaction

Engineering the surface Pt coordination environment is a promising strategy for promoting the kinetically sluggish oxygen reduction reaction (ORR) on Pt-based catalysts. In this study, we achieve the compressive strain effect and electronic effect by Cu and N co-doping to synthesize the PtCuN hollow nanospheres with PtN overlayers (PtCuN@PtN HNSs) using a facile solvothermal synthesis. Electrochemical investigations show that the constructed disordered Pt–N coordination structures effectively facilitate the ORR and stabilize Pt atoms in the compressed lattice, whereas an excessive N-doping can lead to the formation of a structurally unstable Pt nitride phase. Theoretical analyses confirm that the oxygen reduction kinetics on the compressed PtN overlayers are regulated by a synergistic effect resulting from N-doping and lattice compression, circumventing the traditional linear scaling relationships (LSR). The optimized PtCuN@PtN HNSs, with the composition of PtCu0.29N1.1, demonstrate an area-specific activity of 1.98 mA cm–2 and a mass-specific activity of 1.81 A mgPt–1.

Main Group SnN4O Single Sites with Optimized Charge Distribution for Boosting the Oxygen Reduction Reaction.

Transition metal single-atom catalysts (SACs) have been regarded as possible alternatives to platinum-based materials due to their satisfactory performance of the oxygen reduction reaction (ORR). By contrast, main-group metal elements are rarely studied due to their unfavorable surface and electronic states. Herein, a main-group Sn-based SAC with penta-coordinated and asymmetric first-shell ligands is reported as an efficient and robust ORR catalyst. The introduction of the vertical oxygen atom breaks the symmetric charge balance, modulating the binding strength to oxygen intermediates and decreasing the energy barrier for the ORR process. As expected, the prepared Sn SAC exhibits outstanding ORR activity with a high half-wave potential of 0.912 V (vs RHE) and an excellent mass activity of 13.1 A mgSn-1 at 0.850 V (vs RHE), which surpasses that of commercial Pt/C and most reported transition-metal-based SACs. Additionally, the reported Sn SAC shows excellent ORR stability due to the strong interaction between Sn sites and the carbon support with oxygen atom as the bridge. The excellent ORR performance of Sn SAC was also proven by both liquid- and solid-state zinc-air battery (ZAB) measurements, indicating its great potential in practical applications.

Thermodynamics of Proton-Coupled Electron Transfer at Tricopper μ-Oxo/Hydroxo/Aqua Complexes.

Multicopper oxidases (MCOs) utilize a tricopper active site to reduce dioxygen to water through 4H+ 4e- proton-coupled electron transfer (PCET). Understanding the thermodynamics of PCET at a tricopper cluster is essential for elucidating how MCOs harness the oxidative power of O2 while mitigating oxidative damage. In this study, we determined the O-H bond dissociation free energies (BDFEs) and pKa values of a series of tricopper hydroxo and tricopper aqua complexes as synthetic models of the tricopper site in MCOs. Tricopper intermediates on the path of alternating electron and proton transfer (ET-PT-ET-PT-ET) have modest BDFE(O-H) values in the range of 53.0-57.1 kcal/mol. In contrast, those not on the path of ET-PT-ET-PT-ET display much higher (78.1 kcal/mol) or lower (44.7 kcal/mol) BDFE(O-H) values. Additionally, the pKa of bridging OH and OH2 motifs increase by 8-16 pKa units per oxidation state. The same oxidation state changes have a lesser impact on the pKa of N-H motif in the secondary coordination sphere, with an increase of ca. 5 pKa units per oxidation state. The steeper pKa increase of the tricopper center promotes proton transfer from the secondary coordination sphere. Overall, our study shed light on the PCET pathway least prone to decomposition, elucidating why tricopper centers are an optimal choice for promoting efficient oxygen reduction reaction.

Coordination-environment regulation of atomic Co-Mn dual-sites for efficient oxygen reduction reaction

Coordination-environment regulation of atomic Co-Mn dual-sites for efficient oxygen reduction reaction

Electronic Structure Engineering of Pt-Ni Alloy NPs by Coupling of Gold Single Atoms on N-Doped Carbon for Highly Efficient Oxygen Reduction Reaction and Hydrogen Evolution Reaction.

Improving the catalytic activity and durability of platinum-based alloy catalysts remains a formidable challenge in the context of renewable energy electrolysis applications. Herein, a facile and rapid photochemical deposition strategy for the synthesis of gold single atoms (Au SAs) anchored on N-doped carbon is presented. These Au SAs serve as a charge redistribution support for Pt-Ni alloy nanoparticles (PtNiNPs/AuSA-NDC), creating an extended electron-donating interface with Pt-Ni alloy sites. Consequently, the PtNiNPs/AuSA-NDC hybrid catalyst manifests exceptional catalytic performance and durability in both the oxygen reduction reaction (ORR) and hydrogen evolution reaction (HER) under acidic conditions. Specifically, in ORR, it exhibits a half-wave potential (0.92V vs RHE), with a mass activity 20.4 times superior to Pt/C at 0.9V. In HER, PtNiNPs/AuSA-NDC demonstrates a notably reduced overpotential of 19.1mV vs RHE at 10mAcm-2 and a mass activity 38 times higher than Pt/C (at 0.25mV). Furthermore, this hybrid catalyst displays outstanding durability, with only an 8.0mV decay observed for ORR and a 6.9mV decay for HER after 10000 cycles. Theoretical calculations provide insight into the mechanism, demonstrating that isolated Au sites effectively modulate the electronic structure of Pt-Ni alloy sites, facilitating intermediate adsorption and enhancing reaction kinetics.