Effect Of Peening Research Articles

Competitive effect of residual stress and surface roughness on the fatigue life of shot peened S42200 steel at room and elevated temperature

The effect of shot peening (SP) on the fatigue life of S42200 steel at room and elevated temperature is investigated. The fatigue test is carried out on a high temperature rotating bending tester. Surface integrity characterization is used to study the effect of SP on surface properties. Furthermore, Finite Element Method (FEM) combined with a fatigue damage model, namely Zheng Equation, is proposed to predict the fatigue life. The results show that SP effectively improves the fatigue life of S42200 steel under all temperatures. However, at lower temperature, higher strength SP leads to higher fatigue resistance, while at higher temperature, lower strength SP leads to higher fatigue resistance. This can be explained by the competitive effect of surface roughness and compressive residual stress (CRS) relaxation on the local stress concentration. This research can be a good guide to the application of SP at different temperatures.

Analysis of the effects of isothermal aging and Laser Shock Peening on the flow properties, fatigue crack growth, and fracture toughness of Inconel 718

Laser Shock Peening (LSP) is a surface treatment that improves the fatigue life and fatigue strength of components by inducing a shallow layer that is characterized by compressive residual stress and plastic deformation. This study investigates the use of LSP on Inconel 718 (IN718) on the fatigue crack growth (FCG) and fracture toughness (FT) of as-received (AR), solution-treated (SOL), and samples aged for 0.5, 4, and 100 h. Experimental results on aged samples established that the hardness of samples 0.5 and 4 h increased due to the precipitation of γ′ and γ″ phases while in the 100 h sample the hardness decreases due to the presence of coarser γ″ phase and intergranular δ-phase. These microstructural features impacted the plastic flow behavior of the different samples which was adequately described using a two-fitting approach to the Voce equation. While thermal aging accelerated the FCG of aged samples, the plastic flow and residual stress induced by the LSP significantly reduces the effect of thermal aging, by reducing the FCG rate and increasing the FT of the IN718 aged samples. Finally, results from EBSD analysis showed that the LSP-induced plastic strain depends on the microstructural transformations that occurred during the aging treatment.

Effect of Laser Shock Peening on the Stress Corrosion Cracking of 304L Stainless Steel

Storage canisters used in nuclear power plants operating in seaside areas—where the salt content in the atmosphere is high—may be susceptible to chloride-induced stress corrosion cracking (CISCC). Chloride-induced stress corrosion cracking is one of the ways in which dry storage canisters made of stainless steel can degrade. Stress corrosion cracking depends on the microstructure and residual stress, and it is therefore very important to improve the surface properties of materials. Laser shock peening both greatly deforms the material surface and refines grains, and it generates compressive residual stress in the deep part from the surface of the material. This study focused on the effect of laser shock peening on the stress corrosion cracking of 304L stainless steel. The laser shock peening was found to induce compressive residual stress from the surface to a 1 mm depth, and the SCC properties were evaluated by a U-bend test. The results showed that the SCC resistance of laser-peened 304L stainless steel in a chloride environment was enhanced, and that it was closely related to grain size, the pitting potential of the cross section, and residual stress.

Investigating the effect of laser shock peening on the wear behaviour of selective laser melted 316L stainless steel

Selective Laser Melting (SLM) is an emerging additive manufacturing technology that produces metallic parts with high customization. The applications of stainless steel 316L have been restricted owing to their poor tribological performance, especially in the as-printed condition. In this study, SLM-made SS 316L is subjected to laser shock peening (LSP), one of the surface modification techniques, to improve its characteristic microstructure, mechanical and wear behaviour. X-ray diffraction and residual stress analysis show that the laser shock peening promotes micro-level grain refinement and compressive residual stresses in the severely deformed layer, resulting in increased micro-hardness up to 22%. Pin on disk wear test is carried out, and the optimum condition is determined using the Taguchi method for the polished as-printed specimen. The wear rate of polished as-printed and laser shock peened specimens at optimized conditions were 2.4156 × 10−3 mm3 m−1 and 1.7871 × 10−3 mm3 m−1, respectively. The laser shock peened specimen showed higher wear resistance with a 26% reduction in wear rate compared to the polished as-printed specimens.

Enhanced cooling rates in laser directed energy deposition with interlayer peening

PurposeThis study aims to investigate the effect of mechanical peening on the cooling rate of a subsequently deposited layer in a hybrid additive manufacturing (AM) process.Design/methodology/approachIn this experimental study, 20 layers of 316 L stainless steel are built via directed energy deposition, with the tenth layer being subject to various peening processes (shot peening, hammer peening and laser shock peening). The microstructure of the eleventh layer of all the samples is then characterized to estimate the cooling rate.FindingsThe measurements indicate that the application of interlayer peening causes a reduction in primary cellular arm spacing and an increase in micro segregation as compared to a sample prepared without interlayer peening. Both factors indicate an increase in the cooling rate brought about by the interlayer peening.Practical implicationsThis work provides insight into process design for hybrid AM processes as cooling rates are known to influence mechanical properties in laser-based AM.Originality/valueTo the best of the authors’ knowledge, this work is the first of its kind to evaluate the effects of interlayer peening on a subsequently deposited layer in a hybrid AM process.

Effect of shot peening on electrophoretic deposition of bioactive glass coating on AISI 316L stainless steel

Bioactive glass coating of SiO2–CaO–P2O5 was synthesized and deposited on shot peened stainless steel AISI 316L substrates through electrophoretic deposition. Shot peening is known to enhance the fatigue properties of the substrate material; however, the present study aims to investigate how this prior shot peening can affect on the electrophoretic coating properties and performance. Shot peening was carried using two different sets of parameters as conventional shot peening (Almen intensity: 15A and coverage:100%), and severe shot peening (Almen intensity: 7C and coverage:1500%). The coated samples were studied regarding deposition thickness, microstructure, macrotexture and surface roughness, as well as wettability with contact angle tests. Corrosion behavior was also investigated using potentiodynamic polarization and electrochemical impedance spectroscopy in simulated body fluid solutions at 37 °C. The results confirmed that the coating thickness decreased from 55.3 μm for CNP to 27 μm and 9.5 μm for CCSP and CSSP respectively. Shot peening applied before electrophoretic deposition modulated the wettability and corrosion resistance of the coated samples through variation of roughness and the extent of grain refinement. As well as, the water contact angle of CSSP sample was equal to 15.64° which is much lower than CNP (55.3°). Also, the amount of coated samples’ corrosion rate changed by this order CCSP (1.91 × 10−2)>CNP (1.31 × 10−2)>CSSP (1.07 × 10−2). The high surface energy on shot peened samples caused the smaller BG grain size deposited on surfaces. The amount of BG grain size of each sample is as follow CNP 2.12 ± 1.6 μm, CCSP 1.34 ± 0.8 μm and CSSP 0.81 ± 0.3 μm.

Effect of Ultrasonic Shot Peening and Laser Shock Peening on the Microstructure and Microhardness of IN738LC Alloys.

IN738LC is a conventional-cast Ni-based superalloy intended for power generation and aerospace applications. Typically, ultrasonic shot peening (USP) and laser shock peening (LSP) are utilized to enhance cracking, creep, and fatigue resistance. In this study, the optimal process parameters for USP and LSP were established by observing the microstructure and measuring the microhardness of the near-surface region of IN738LC alloys. The LSP impact region (modification depth) was approximately 2500 μm, which was much higher than the USP impact depth of 600 μm. The observation of the microstructural modification and resulting strengthening mechanism revealed that the build-up of dislocations upon peening with plastic deformation was crucial for alloy strengthening in both methods. In contrast, significant strengthening via γ' shearing was observed only in the USP-treated alloys.

EFFECTS OF SHOT PENNING ON MECHANICAL PROPERTIES, MICROSTRUCTURAL EVOLUTION AND RESIDUAL STRESS OF SUBMERGED FRICTION STIR-WELDED AA6061-T6 ALLOY

The purpose of this work is to study the effect of shot peening on the mechanical characteristics of welded plates which were performed by Submerged Friction Stir Welding (SFSW) on AA6061-T6 alloy. SFSW was carried out under three cooling mediums like water, brine solution, and coolant oil at the rotational speed of 1200[Formula: see text]rpm and welding speed of 45[Formula: see text]mm/min, respectively. The welded samples from each cooling medium were subjected to a shot peening process. A tensile test was carried out on weld peened and welds unpeened joints. The hardness of the various zones of HAZ, TMAZ, and NZ was also investigated. Optical and scanning electron microscopy was used to examine the microstructures of peened and unpeened joints formed by coolant samples. Shot peening has the potential to enhance the compressive residual stress of friction stir welded joints. According to these findings, shot peening had a greater impact on the mechanical properties of welded samples than unpeened samples, including tensile strength, percentage of elongation, and hardness. The grain size was a little bit smaller than the FSW sample because the surface of the welded samples was subjected to more strain during shot peening.

Effect of Water Jet Cavitation Peening on Short-Period Oxidation Behavior of Alloy 600 in PWR Primary Water

Water jet cavitation peening (WJCP) was used to strengthen the surface of nickel-based alloy 600. Residual stress, hardness, surface roughness, microstructure, and short-period oxidation behavior in untreated (UT) and WJCP-treated alloy 600 were characterized. A continuous oxide film was formed on the WJCP-treated surface after a short period of exposure, while it was discontinuous in the UT specimen. The change in oxidation behavior was attributed to the ultrafine grain and dislocation structure resulting from the WJCP treatment.

Effect of laser shock peening on the tensile behavior and notch sensitivity of Ni-based single-crystal superalloy

Effect of laser shock peening on the tensile behavior and notch sensitivity of Ni-based single-crystal superalloy

Effects of Micro-Shot Peening on the Fatigue Strength of Anodized 7075-T6 Alloy.

Micro-shot peening under two Almen intensities was performed to increase the fatigue endurance limit of anodized AA 7075 alloy in T6 condition. Compressive residual stress (CRS) and a nano-grained structure were present in the outermost as-peened layer. Microcracks in the anodized layer obviously abbreviated the fatigue strength/life of the substrate. The endurance limit of the anodized AA 7075 was lowered to less than 200 MPa. By contrast, micro-shot peening increased the endurance limit of the anodized AA 7075 to above that of the substrate (about 300 MPa). Without anodization, the fatigue strength of the high peened (HP) specimen fluctuated; this was the result of high surface roughness of the specimen, as compared to that of the low peened (LP) one. Pickling before anodizing was found to erode the outermost peened layer, which caused a decrease in the positive effect of peening. After anodization, the HP sample had a greater fatigue strength/endurance limit than that of the LP one. The fracture appearance of an anodized fatigued sample showed an observable ring of brittle fracture. Fatigue cracks present in the brittle coating propagated directly into the substrate, significantly damaging the fatigue performance of the anodized sample. The CRS and the nano-grained structure beneath the anodized layer accounted for a noticeable increase in resistance to fatigue failure of the anodized micro-shot peened specimen.

Effect of abrasive water jet peening on NaCl-induced hot corrosion behavior of Ti–6Al–4V

Hot corrosion studies were performed on pristine and abrasive water jet peened (AWJP) Ti–6Al–4V surfaces. Oxide scales form on the peened and pristine surfaces when coated with NaCl and exposed to 600 °C for 100 h. Despite similar oxide compositions on both surfaces, the thickness and roughness of the oxide scale on the AWJ peened surface is lower. The hot corrosion rate of the pristine surface is 2.5 times higher than that on the AWJ peened surface. Enhanced hot corrosion resistance of the latter is attributed to compressive residual stresses on the surface that retards diffusion of chloride in the material.

Effect of Laser Shock Peening without Coating on Grain Size and Residual Stress Distribution in a Microalloyed Steel Grade

This study aimed to identify the optimal combination of wavelength and laser pulse density to achieve the optimal pulse pressure that can induce the maximum compressive residual stress at the subsurface of microalloyed steel. For this, laser shock peening without coating (LSPwC) was performed on microalloyed steel samples at the fundamental wavelength (1064 nm) with pulse densities of 3, 6, 9, and 12 GW/cm2 and at the second harmonic wavelength (532 nm) with pulse densities of 3, 6, and 9 GW/cm2. The residual stress distributions were studied to a depth of 500 µm in the laser-treated samples. Tensile residual stress was observed at the surface of laser-peened specimens in both wavelength conditions (1064 and 532 nm). The significant impartment of compressive residual stress across the depth was achieved at the fundamental wavelength (1064 nm). The maximum compressive residual stress was attained with a laser pulse density of 9 GW/cm2 in the 1064nm wavelength condition. The optical micrographic analysis in the subsurface regions of the LSPwC specimen at 1064 nm and 9 GW/cm2 shows evidence of a high degree of plastic deformation. Electron backscatter diffraction (EBSD) analysis shows that there is grain refinement due to plastic deformations in samples subjected to the fundamental wavelength. Microhardness distribution analysis across the subsurface region shows work-hardening effects in the laser-processed samples in the 1064 nm condition. This study also shows that there is an indication of a thermal softening effect in the samples treated with the 532 nm wavelength, and it is correlated with lower compressive residual stress across the depth.

Effects of Ultrasonic Shot Peening on the Corrosion Resistance and Antibacterial Properties of Al0.3Cu0.5CoCrFeNi High-Entropy Alloys

Cu-bearing high-entropy alloys (HEAs) have been proposed for use as structural materials in the marine environment due to their superior mechanical and antimicrobial properties. However, the Al, Cu-enriched precipitations in HEAs damage their corrosion resistance. In this study, we used ultrasonic shot peening (USSP) technology to solve this problem. USSP caused severe plastic deformation of the Al0.3Cu0.5CoCrFeNi HEA surface and dispersed the long-strip Al, Cu-enriched phases into scattered dots, which reduced the galvanic corrosion of the HEA and enhanced passive film formation. The Al, Cu-enriched scattered precipitations also increased the number of Cu2+ ion dissolution sites, leading to the improvement of the alloy’s antibacterial properties.

The Effect of Laser Shock Peening on Back Stress of Additively Manufactured Stainless Steel Parts

Abstract This work studies the use of laser shock peening (LSP) to improve back stress in additively manufactured (AM) 316L parts. Unusual hardening behavior in AM metal due to tortuous microstructure and strong texture poses additional design challenges. Anisotropic mechanical behavior complicates application for mechanical design because 3D printed parts will behave differently than traditionally manufactured parts under the same loading conditions. The prevalence of back-stress hardening or the Bauschinger effect causes reduced fatigue life under random loading and dissipates beneficial compressive residual stresses that prevent crack propagation. LSP is known to improve fatigue life by inducing compressive residual stress and has been applied with promising results to AM metal parts. It is here demonstrated that LSP may also be used as a tool for mitigating tensile back-stress hardening in AM parts, thereby reducing anisotropic hardening behavior and improving design use. It is also shown that the method of application of LSP to additively manufactured parts is key for achieving effective back-stress reduction. Back stress is extracted from additively manufactured dog bone samples built in both XY and XZ directions using hysteresis tensile. Both LSPed and as-built conditions are tested and compared, showing that LSPed samples exhibit a significant reduction to back stress when the laser processing is applied to the sample along the build direction. Electron backscatter diffraction (EBSD) performed under these conditions elucidates how grain morphologies and texture contribute to the observed improvement. Crystal plasticity finite element (CPFE) modeling develops insights as to the mechanisms by which this reduction is achieved in comparison with EBSD results. In particular, the difference in plastic behavior across build orientations of identified crystal planes and grain families are shown to impact the degree of LSP-induced back-stress reduction that is sustained through tensile loading.

Effect of Laser Peening on the Corrosion Properties of 304L Stainless Steel.

Dry canisters used in nuclear power plants can be subject to localized corrosion, including stress corrosion cracking. External and residual tensile stress can facilitate the occurrence of stress corrosion cracking. Residual stress can arise from welding and plastic deformation. Mitigation methods of residual stress depend upon the energy used and include laser peening, ultrasonic peening, ultrasonic nanocrystal surface modification, shot peening, or water jet peening. Among these, laser peening technology irradiates a continuous laser beam on the surface of metals and alloys at short intervals to add compressive residual stress as a shock wave is caused. This research studied the effect of laser peening with/without a thin aluminum layer on the corrosion properties of welded 304L stainless steel. The intergranular corrosion rate of the laser-peened specimen was a little faster than the rate of the non-peened specimen. However, laser peening enhanced the polarization properties of the cross-section of 304L stainless steel, while the properties of the surface were reduced by laser peening. This behavior was discussed on the basis of the microstructure and residual stress.

Additively Manufactured 316L Stainless Steel Subjected to a Duplex Peening-PVD Coating Treatment.

This research studies the individual and combined effects of mechanical shot peening and the deposition of TiAlCuN coating on additively manufactured 316L stainless steel. Shot peening has been found to induce a 40% increase in surface hardness, while the combined effect of shot peening and the coating produced an approximately three-fold increase in surface hardness when compared to the as-printed coupons. Shot peening reduced the surface roughness of printed metal coupons by 50%, showing that shot peening can also serve to improve the surface finish of as-printed 316L stainless steel components. The peening process was found to induce a compressive residual stress of 589 MPa, with a maximum affected depth of approximately 200 μm. Scratch testing of the printed and coated specimens showed complete delamination failure at a normal load of 14 N, when compared to hybrid treated samples which failed at 10 N. On the other hand, from the corrosion tests, it was found that the hybrid treated samples provided the optimal results as opposed to the other variables.

Effect of ultrasonic shot peening on electrodeposited Ni and Cu coatings on Cu substrate

In this study, the effect of ultrasonic shot peening (USSP) on bilayered Ni and Cu coatings on Cu substrate was studied. On the Cu substrate, Ni and Cu coatings were sequentially electrodeposited followed by ultrasonic shot peening with a varying shot diameter and peening time. Apart from phase analysis and microscopy study of the coatings (before and after peening), hardness, compressive residual stress, wear, and corrosion resistances are also examined. Improvement of surface-mechanical properties and electrochemical properties were observed in specific peening conditions. There was also a noticeable improvement in residual compressive stress as an effect of peening.

What can micromechanics tell us about the surface integrity of shot-peened materials?

Standard techniques for assessing shot peening include XRD and EBSD for measuring residual stresses and severe deformation beneath the surface; however, these techniques do not consider the localised micromechanical behaviour. Here, single-grain micropillar compression tests in a Ni-base superalloy reveal that the micromechanical effect of shot peening could be insignificant due to the machining-induced pre-strained condition of the surface. Further, it is shown that shot-peening-induced strengthened layer can extend much less (∼50%) than the depth at which compressive stresses are still present. This work highlights the need for employing micromechanics as a complementary shot peening assessment technique for machined components.

Effect of Laser Peening on Fatigue Properties of Butt-Welded Joints with Angular Distortion

Effect of Laser Peening on Fatigue Properties of Butt-Welded Joints with Angular Distortion