Effect Of Particle Size Research Articles

Studies the Effect of Particle Size, Binder Ratio and Pressure on Compaction Energy of Water Hyacinth Briquettes

Studies the Effect of Particle Size, Binder Ratio and Pressure on Compaction Energy of Water Hyacinth Briquettes

Fast Pyrolysis of Municipal Green Waste in an Auger Reactor: Effects of Residence Time and Particle Size on the Yield and Characteristics of Produced Oil

The development of renewable sources for energy production has assumed a vital role in recent years, particularly with regard to the preservation of energy supplies and the environment. In this regard, municipal green waste (MGW) can be a potential renewable energy source if it is integrated with emerging technology, like pyrolysis. Therefore, this study aimed at investigating the effect of residence time and particle size on the yield and composition of oil derived from MGW using fast pyrolysis in an auger reactor. The residence time and particle size were varied from 1 min to 4 min and 1 mm to 10 mm, respectively, while keeping the temperature constant at 500 °C. At a residence time of 3 min, a 2 mm particle size provided the highest bio-oil yield (39.86%). At this experimental setting, biochar yield of 27.16% and syngas yield of 32.98% were obtained. The characterization of produced bio-oil revealed that a total of nine functional groups were present in the bio-oil. The phenols were highest in amount, followed by aromatics and ketones. The increase in residence time decreased the amount of acidic compounds present in the bio-oil. The water content was decreased by ~11% and the calorific value was increased by ~6% with the increase in particle size from 1 mm to 10 mm. Other properties, such as viscosity, density, cetane number, and flash point, did not change significantly with the change in experimental conditions. With a calorific value of 25+ MJ/kg, although the bio-oil produced from MGW can be used for heating (such as in boilers and furnaces), the use of MGW bio-oil in engines requires appropriate upgrading through procedures like hydrodeoxygenation, catalytic cracking, esterification, etc.

Effects of particle size and particle concentration of poly (ethylene‐co‐methacrylic acid) on properties of epoxy resin

AbstractSelf‐healing polymers have been developed to improve durability and reduce costs associated with maintenance during service. The addition of thermoplastics to thermosets to produce mendable polymers appears as a promising self‐healing technique. In this study, poly (ethylene‐co‐methacrylic acid) (EMAA) was added to epoxy resin and the effects of EMAA addition on epoxy properties were evaluated. Specimens with two different contents of thermoplastic and particles sizes were manufactured. A two‐level full factorial experimental design was used to evaluate the effect of particle size and particle content on properties of epoxy modified with addition of EMAA. Tensile tests and dynamic mechanical analysis (DMA) were used and the evaluated responses were tensile strength, modulus of elasticity, and glass transition temperature (Tg). X‐ray computed tomography (XCT) was used to investigate particle size and concentration after manufacturing. It was found that the particle concentration has greater effects on stress–strain behavior of epoxy while Tg was not significantly affected by neither of the analyzed entrance variables.

Agricultural waste-based modified biochars differentially affected the soil properties, growth, and nutrient accumulation by maize (Zea mays L.) plants

Biochar (BC) is an organic compound formed by the pyrolysis of organic wastes. Application of BCs as soil amendments has many benefits including carbon sequestration, enhanced soil fertility and sustainable agriculture production. In the present study, we acidified the different BCs prepared from rice straw, rice husk, wheat straw, cotton stalk, poultry manure, sugarcane press mud and vegetable waste; following which, we applied them in a series of pot experiments. Comparisons were made between acidified and non- acidified BCs for their effects on seed germination, soil properties (EC, pH) nutrient contents (P, K, Na) and organic matter. The treatments comprised of a control, and all above-described BCs (acidified as well as non-acidified) applied to soil at the rate of 1% (w/w). The maize crop was selected as a test crop. The results showed that acidified poultry manure BC significantly improved germination percentage, shoot length, and biomass of maize seedlings as compared to other BCs and their respective control plants. However, acidified BCs caused a significant decrease in nutrient contents (P, K, Na) of soil,maize seedlings, and the soil organic matter contents as compared to non- acidified BCs. But when compared with control treatments, all BCs treatments (acidified and non-acidified) delivered higher levels of nutrients and organic matter contents. It was concluded that none of the BCs (acidified and non-acidified) had caused negative effect on soil conditions and growth of maize. In addition, the acidification of BC prior to its application to alkaline soils might had altered soil chemistry and delivered better maize growth. Moving forward, more research is needed to understand the long-term effects of modified BCs on nutrient dynamics in different soils. In addition, the possible effects of BC application timings, application rates, particle size, and crop species have to be evaluated systemtically.

Effects of particle size on toxicity, bioaccumulation, and translocation of zinc oxide nanoparticles to bok choy (Brassica chinensis L.) in garden soil

The indiscriminate use of zinc oxide nanoparticles (ZnO NPs) in daily life can lead to their release into soil environment. These ZnO NPs can be taken up by crops and translocated to their edible part, potentially causing risks to the ecosystem and human health. In this study, we conducted pot experiments to determine phytotoxicity, bioaccumulation and translocation depending on the size (10 – 30 nm, 80 – 200 nm and 300 nm diameter) and concentration (0, 100, 500 and 1000 mg Zn/kg) of ZnO NPs and Zn ion (Zn2+) in bok choy, a leafy green vegetable crop. After 14 days of exposure, our results showed that large-sized ZnO NPs (i.e., 300 nm) at the highest concentration exhibited greater phytotoxicity, including obstruction of leaf and root weight (42.5 % and 33.8 %, respectively) and reduction of chlorophyll a and b content (50.2 % and 85.2 %, respectively), as well as changes in the activities of oxidative stress responses compared to those of small-sized ZnO NPs, although their translocation ability was relatively lower than that of smaller ones. The translocation factor (TF) values decreased as the size of ZnO NPs increased, with TF values of 0.68 for 10 – 30 nm, 0.55 for 80 – 200 nm, and 0.27 for 300 nm ZnO NPs, all at the highest exposure concentration. Both the results of micro X-ray fluorescence (μ-XRF) spectrometer and bio-transmission electron microscopy (bio-TEM) showed that the Zn elements were mainly localized at the edges of leaves exposed to small-sized ZnO NPs. However, the Zn elements upon exposure to large-sized ZnO NP were primarily observed in the primary veins of leaves in the μ-XRF data, indicating a limitation in their ability to translocate from roots to leaves. This study not only advances our comprehension of the environmental impact of nanotechnology but also holds considerable implications for the future of sustainable agriculture and food safety.

Investigation into the ignition sensitivity and detonation kinetics of Al/RDX energetic dust

Given the prevalence of Al/RDX energetic dust in industrial production, this study investigates their ignition safety and explosion hazards using Hartmann tubes and 20 L spherical explosion containers. The minimum ignition energy (MIE) increases from 20 mJ to 55 mJ as RDX content increases, indicating that adding RDX enlarges the effective particle size of the dust, thereby reducing its ignition sensitivity. A logistic regression model was used to develop a fitting equation for ignition probability, correlating dust concentration and ignition energy. The flame propagation velocity and explosion pressure of the energetic dust initially increase and then decrease with increasing RDX content. Optimal combustion characteristics were observed at 20 % RDX, with the maximum flame propagation velocity of 101 m s−1. However, the peak flame temperature decreases with increasing RDX content. The maximum explosion pressure and maximum explosion index at 1.77 MPa and 186.99 MPa m s−1 respectively, at 40 % RDX content. These findings highlight that 20 % RDX content yields the best combustion characteristics, while 40 % RDX content offers the maximum explosive potential, providing valuable insights for enhancing safety measures in industrial applications involving energetic dusts.

The role of chlorine promoters in mediating particle size effects in silver-catalyzed ethylene epoxidation

Measured chlorine coverages over Ag/α-Al2O3 catalysts with varying Ag weight loadings (1.3–35 wt%) and different Ag particle size distributions when parsed in terms of Cl coverages over particles of varying size constituted in the distribution reveal that Ag particles of size below ∼30 nm are covered in more than 1 monolayer (ML) of chlorine in presence of 3.5 ppm C2H5Cl. These assessments of Cl coverages were made possible by correlating the cumulative Cl coverage to the lognormal surface area distribution of 22 Ag/α-Al2O3 samples using a single exponential decay function. Fully chlorided small Ag particles exhibit low rates of epoxidation and only large Ag particles which exhibit sub-monolayer Cl coverages catalyze ethylene epoxidation with high ethylene oxide (EO) rates and selectivity. The Ag particle size dependence of Cl coverages plausibly explains why ≥ 100 nm Ag particles are typical in promoted Ag/α-Al2O3 ethylene epoxidation catalysts.

Experimental study of solid particles in thermal energy storage systems for shell and tube heat exchanger: Effect of particle size and flow direction

The solid particle thermal energy storage method offers cost-effective, simple, and high-temperature suitable solutions. It effectively resolves chemical compatibility and thermal stress issues in shell-and-tube heat exchangers. This work studies the quartz sands' particle sizes and flow direction's impact on heat exchanger performance. The results show that heat conduction and natural convection heat transfer mechanisms exist on the particle side. Flow direction minimally affects charge/discharge time and stored energy but significantly impacts delivered/recovered energy and exergy and energy and exergy efficiencies. Optimal performance is achieved when HTO enters from the top during charging and from the bottom during discharging, creating a transparent thermal gradient of “Top Temperature High, Bottom Temperature Low”. This distribution minimizes natural convection losses, resulting in a 15–17 % increase in energy efficiency and an 11–13 % increase in exergy efficiency compared to reverse flow. Smaller particles show slightly faster temperature rise due to lower energy storage density. Large and medium particles perform well, achieving energy efficiencies of 81.5 % and 81.0 % and exergy efficiencies of 62.1 % and 61.8 %, respectively. Small particles have an energy efficiency of 79.0 % and an exergy efficiency of 60.4 %, possibly due to higher porosity and increased heat losses.

Effect of particle size on the rheology, baking characteristics, and microstructure of fava bean-fortified bread

Effects of substituting fava beans flour of three particle sizes (0.14 mm, 0.5 mm, and 1.0 mm) at 10, 20, 30 and 40% to wheat flour were determined on the rheological properties, baking characteristics, and microstructure of bread. Rheological properties of the dough produced from the flour blends showed that the 10, 20, and 30% substitution levels yielded considerably good viscoelastic properties and were used for the test baking. The baking characteristics, such as loaf volume, C-Cell analysis, and scorings, were evaluated to understand the implications of blend levels on the quality characteristics of the bread. The fava bean flour substitution level had more impact on the quality characteristics of bread than the particle size. Also, microstructural analyses using X-ray microcomputed tomography showed that increasing the concentration of fava bean flour had a significant effect (p < 0.05) on the bread's microstructure. For all the quality characteristics examined, samples with 10% substitution levels, regardless of particle size, produced loaves closest to the bread made with wheat flour alone. The findings of this study contribute valuable knowledge to optimizing fava bean-fortified bread formulations, allowing for a good understanding of the trade-offs between particle size, substitution levels, and the final product quality.

Optimization of natural dye extraction from the root of Rumex abyssinicus plant using response surface methodology

In this study, Rumex abyssinicus (R. abyssinicus) roots were used for dye extraction via Soxhlet extraction. The effects of particle size, solid-to-liquid ratio and extraction time on dye yield were examined. The optimization of dye extraction wascarried out using response surface methodology coupled with the Box–Behnken approach. A maximum dye yield of 53 % was attained at an optimumparticle size of 0.355 mm, a solid-to-liquid ratio of 0.075 g/mL and an extraction time of 5 h. Functional group analysis using FTIR and a UV–vis spectrophotometer was performed to determine the characteristics of the extracted dye. The FTIR analysis results showed the presence of various functional groups in the extracted dye. Additionally, UV–vis spectrophotometer confirmed that the maximum absorbance peakwas detected at 281 nm, with an absorbance of 0.908. Overall, the results show that R. abyssinicus root is a potential source ofdye that has applications in various industries.

Evolving Particles in the 2022 Hunga Tonga—Hunga Ha'apai Volcano Eruption Plume

AbstractThe Multi‐angle Imaging SpectroRadiometer (MISR) aboard NASA's Terra satellite observed the Hunga Tonga—Hunga Ha'apai (HTHH) 15 January eruption plume on eight occasions between 15 and 23 January 2022. From the MISR multi‐angle, multi‐spectral imagery we retrieve aerosol plume height geometrically, along with plume‐level motion vectors, and derive radiometrically constraints on particle effective size, shape, and light‐absorption properties. Parts of two downwind aerosol layers were observed in different places and times, one concentrated in the upper troposphere (11–18 km ASL), and a mid‐stratosphere layer ∼23–30+ km ASL. After the initial day (1/15), the retrievals identified only spherical, non‐light‐absorbing particles, typical of volcanic sulfate/water particles. The near‐tropopause plume particles show constant, medium‐small (several tenths of a micron) effective size over 4 days. The mid‐stratosphere particles were consistently smaller, but retrieved effective particle size increased between 1/17 and 1/23, though they might have decreased slightly on 1/22. As a vast amount of water was also injected into the stratosphere by this eruption, models predicted relatively rapid sulfate particle growth from the modest amounts of SO2 gas injected by the eruption to high altitudes along with the water (Zhu et al., 2022, https://doi.org/10.5194/acp‐22‐10267‐2022). MISR observations up to 10 days after the eruption are consistent with these model predictions. The possible decrease in stratospheric particle size after initial growth was likely caused by evaporation, as the plume mixed with drier, ambient air. Particles in the lower‐elevation plume observed on 1/15 were larger than all the downwind aerosols and contained significant non‐spherical (likely ash) particles.

Effect of Particle Size and Application Pressure in Air-Borne Particle Abrasion on the Adhesion of Polyetheretherketone.

This study aims to investigate the effect of different particle sizes and pressures on the shear bond strength (SBS) and the roughness (Ra) of polyetheretherketone. A total of 117 polyetheretherketone specimens were fabricated and divided into a control (CN: no air-particle abrasion) and eight pre-treatment groups (air-abraded with 50- or 110-μm Al2O3 particles at 1(A), 1.5(B), 2(C), and 2.5(D) bar). The adhesive, Visio.link was used. Thermal aging was performed. Surface properties, SBS and failure mode were assessed. Data was analyzed by linear regression, Pearson correlation and Dunnett's T3 test for pairwise comparisons (p⟨0.05). The highest and lowest Ra were found in the 110D and CN groups respectively, and the highest SBS results were obtained from the 50B group. Pressure and particle size showed significant difference on the investigated properties (p⟨0.001). Only adhesive failure was observed in the CN, and resin cohesive failure was observed in addition to adhesive failure in the overall study groups. The air-borne particle abrasion procedures and the adhesive material combination are critical to the strength of the polyetheretherketone bond. The combination of visio.link with the pre-treatment option of 50-μm Al₂O₃ particles applied at 1.5-bar pressure delivered the most favorable results.

Effect of diamond particle size on thermal conductivity and thermal stability of Zr-diamond/Cu composite

The diamond particle size plays a critical role in regulating the thermal conductivity of diamond/Cu composite. However, the dependence of diamond particle size on thermal conductivity is generally interfered with interface carbides, and the effect of diamond particle size on the thermal stability of diamond/Cu composite has not been addressed. In this study, we fixed the thickness of the ZrC interlayer between Cu and diamond at around 60 nm and varied diamond particle size from 54 to 272 μm to investigate the relationship between diamond particle size and composite thermal conductivity. The thermal conductivity of the Zr-diamond/Cu composite increases with increasing diamond size. A high thermal conductivity of 820 W/mK is obtained with a diamond particle size of 272 μm. The thermal conductivities of all composites are decreased after 100 thermal cycles, and the diamond/Cu composite with large diamond particle size shows better thermal stability during thermal cycling. The findings emphasize the importance of tailoring diamond particle size to attain high thermal conductivity in the diamond/Cu composites and provide useful guidelines for their thermal management applications.

Effect of particle size and concentration of Al2O3 on the corrosion behavior of silane-Al2O3/MWCNT double-layer coating: towards protecting the AZ91 magnesium alloy

Effect of particle size and concentration of Al2O3 on the corrosion behavior of silane-Al2O3/MWCNT double-layer coating: towards protecting the AZ91 magnesium alloy

Organic Waste for Bioelectricity Generation in Microbial Fuel Cells: Effects of Feed Physicochemical Characteristics

Food waste (FW), piggery waste (PW), and activated sludge (AS) were investigated as potential organic feeds for bioelectricity generation in laboratory-scale microbial fuel cells (MFCs). The MFCs fed by FW gained the highest maximum power density at 7.25 W/m3, followed by those fed by PW at 3.86 W/m3 and AS at 1.54 W/m3. The tCOD removal in the FW-, PW-, and AS-MFCs reached 76.9%, 63.9%, and 55.22%, respectively, within a 30-day retention time. Food waste, which resulted in the highest power density and tCOD removal, was selected for a series of following tests to investigate the effects of some physicochemical properties of organic feed on the performance of MFCs. The effect of feed particle size was tested with three controlled size ranges (i.e., 3, 1, and &lt;1 mm) in MFCs. A smaller feed particle size provided a higher power density of 7.25 W/m3 and a tCOD removal of 76.9% compared to the MFCs fed with organic waste with a larger particle size. An increment in feed moisture from 70% to 90% improved the maximum power density from 7.2 to 8.5 W/m3, with a 17.5% enhancement, and improved the tCOD removal from 75.8% to 83.3%, with a 10.0% enhancement. A moderate C/N ratio of approximately 30/1 maximized the power density and COD removal (7.25 W/m3 and 81.73%) in the MFCs compared to C/N ratios of 20/1 (4.0 W/m3 and 64.14%) and 45/1 (4.38 W/m3 and 71.34%).

Effect of limestone particle size and microbial phytase on phosphorus and calcium digestion kinetics along the gastrointestinal tract in laying hens

ABSTRACT 1. This study assessed the effect of limestone particle size and microbial phytase incorporation on the fate of phosphorus (P) and calcium (Ca) along the gastrointestinal tract in 72 laying hens. 2. Four experimental diets were formulated according to a 2 × 2 factorial arrangement to evaluate the effect of two coarse limestone (CL) inclusion. This included a mix (MIX) of 75% CL (2 − 4 mm) and 25% fine particles (FL, <0.5 mm) or 100% FL, in two different basal diets formulated without (MIX0 and FL0) or with 300 FTU of microbial phytase/kg (MIX300 and FL300). 3. Contents of the crop, gizzard, duodenum, jejunum and ileum were collected to determine the mean retention time (MRT) of dry matter (DM), the recovery rate of Ca and P in each segment of the gastrointestinal tract and the apparent fractional digestibility coefficient (AD) of Ca and P in each intestinal segment. 4. In hens fed FL, microbial phytase decreased the MRT of DM along the intestine (p < 0.05). In the crop and the gizzard, Ca recovery increased with MIX incorporation to a greater extent in hens fed without microbial phytase (p < 0.05). The mixed particle size incorporation decreased absorption kinetics of Ca in hens fed microbial phytase. The AD of P and the absorption kinetics of P were significantly decreased in hens receiving FL300, probably due to complex formation between Ca and phytic acid. 5. This study showed that coarse limestone particles incorporation improved mineral utilisation along the digestive tract.

Ultra‐Small Au Nanoclusters with Tailored Photoluminescence Properties using Modified Thiol Ligands: A Computational and Experimental Demonstration

AbstractAu nanoclusters with tailored photoluminescence can be obtained through controlled nanoparticle ligand interface chemistry. The present work reports molecular gold nanoclusters with tuneable photoluminescence emission from 600 to 700 nm using N,N′,N″‐trialkyl (11‐mercaptoundecyl)ammonium chloride ligands as capping‐agents. The tunability within red spectral region is regulated through specific interface chemistry between gold nanoclusters of molecular range and functional groups of the quaternary ammonium head over N,N′,N″‐trialkyl(11‐mercaptoundecyl)ammonium chloride. Combined understanding obtained from the spectroscopy, microscopy, and density functional theory studies demonstrate that the functional group specific electronic interactions at the interfaces steer the emission characteristics of “molecular” Au nanoparticles. The study clearly identifies that bulkier functional groups, i.e., triethyl, tripropyl, tributyl, and dimethyl benzene over N+ (of thiol ligand) through their steric effects minimize the particle size giving rise to tunable photoluminescence emission in red spectral region. However, the red shift seen in the emission Au nanoclusters with N‐(11‐mercaptoundecyl)‐N,N′‐dimethylbenzenammonium chloride ligand in contradiction to particle size effect is computationally proved to be due to the delocalization of electron density from benzene aromatic ring to N+ of ammonium head leading to a reduction in the HOMO‐LUMO energy gap.

Effect of particle size and application rate of steel (Linz-Donawitz, LD) slag on heavy metal built-up in soil and their transfer dynamics in spinach (Spinacia oleracea L.)

Linz-Donawitz (LD) slag is a solid industrial waste generated during the production of steel. In general, the amount of LD slag produced varies from 300 to 400 kg ton-1 of steel. Presently only 25 % of the steel slag, which is also rich in various macro and micro-nutrients, is being reused in India compared to 70–100 % in other countries. The present study deals with the possibility of utilizing LD slagas a nutrient rich low-cost soil conditioner in agriculture. An experiment was thus conducted to determine the effect of LD slag application at rates 0.25, 0.50 and 1 t ha-1 in two particle sizes i.e., <50 and <100 microns (µ) on spinach (Spinacia oleracea L.). Physico-chemical, biological characteristics and heavy metals in soil and latter’s transfer from soil to the foliage was also determined. The results showed that an application of LD slag @1 tha-1 and 100 µ particle size significantly improved the soil microbial count and activity of enzymes such as dehydrogenase and phosphatase while at a smaller particle size of LD slag (50 µ) @ 1 tha-1, a significant increase in the foliage yield of spinach was observed. The risk due to heavy metals present in the steel slag as evidence by indicator of heavy metal content in plants i.e. transfer factor (TF), hazard quotient (HQ) and hazard index (HI) was within the permissible range. However long-term effect of steel slag application on ecotoxicity and phytotoxicity levels must be deciphered. In conclusion the application of LD slag in spinach does not negatively impact the soil health and in fact causes an increase in the economic yield of spinach.

Effect of particle size on optical and electrical properties of thin films – a simulation approach

This paper presents a simulated investigation of the relationship between surface roughness and particle size as well as the resulting impact of the both on the thin film’s physical and optical properties. Non-porous thin films are created through computer simulation for a range of particle sizes following the random deposition with a surface relaxation approach. For the deposited thin films different fundamental parameters like transmittance, reflectance, absorption coefficients, frequency dependent dielectric constants, loss angle, refractive indices, optical band gap have all been calculated and in this process of calculation the fundamental values of two different materials; zinc oxide (ZnO and cadmium selenide (CdSe) are taken. It has been seen that when the particle sizes are comparable the calculated values of optical band gap of both ZnO and CdSe matches well with the experimental values of the same reported by others. This is probably the first effort to develop a direct relation between the particle size with different fundamental optical properties of different materials through simple simulation which agrees well with the experimental result. This would definitely help the experimental researchers in the field of material science to design their experiments as per the desired requirements.

Effects of different solid particle sizes on oat protein isolate and pectin particle-stabilized Pickering emulsions and their use as delivery systems

Oat protein isolate (OPI)/high methoxyl pectin (HMP) complexes (OPP) were prepared to stabilized Pickering emulsions and applied as nutraceutical delivery systems. The different mass ratios and pH changed the interactions between OPI and HMP that caused the different size of OPP. Specifically, smaller particle size of OPP (125.7–297.6 nm) were formed when hydrophobic interactions along with electrostatic forces predominant in OPP (OPI:HMP = 3:1, pH 4, 5). Among these particles, OPP-2 could stabilize Pickering emulsion efficiently through formation of dense interfacial film, which exhibited the highest apparent viscosity and the smallest average droplet size (23.39 μm). Moreover, OPP-2 stabilized Pickering emulsions with superior stability not only exhibited higher encapsulation efficiency of 85.63%, but also could control curcumin release in simulated gastrointestinal fluids to improve curcumin's bioaccessibility. These results verified the possibility of OPP to be a Pickering emulsions stabilizer, and also identified its potential to be a stable delivery system for bioactive compounds.