Duty Ratio Research Articles

Preparation, structural and functional characterization of corn peptide-chelated calcium microcapsules using synchronous dual frequency ultrasound

The utilization of peptide-chelated calcium is low due to the influence of factors such as solubility, heat and digestive environmental conditions; therefore, it is crucial to protect, prolong and stabilize this nutrient in order to enhance its efficacy. This study was conducted to prepare corn peptide-chelated calcium microcapsules using β-cyclodextrin (β-CD) as the wall material through an improved ultrasonic-assisted method. The structure, solubility, thermal stability, and in vitro gastrointestinal digestion of these microcapsules were thoroughly investigated and analyzed. The microcapsules were prepared using the following recommended conditions: a chelate concentration of 5 mg/mL, a mass ratio of chelate to β-CD of 1:8 g/g, and a synchronous dual-frequency ultrasound (20/28 kHz) at a power of 75 W, a duty ratio of 20/5 s/s, and a time of 20 min. These specific parameters were carefully selected to ensure the optimal fabrication of the microcapsules. The results showed that the utilization of dual-frequency ultrasound resulted in a significant increase in both the encapsulation rate and yield, which were enhanced by 15.84 % and 15.68 %, respectively, reaching impressive values of 79.17 % and 90.60 %. Moreover, the results of the structure index analysis provided further confirmation that ultrasonic treatment had a significant impact on the structure of the microcapsules, leading to a noticeable reduction in particle size and transformation into nanoparticles. Furthermore, the microcapsules demonstrated excellent solubility within a wide pH range of 2 to 10, with solubility ranging from 93.54 % to 88.68 %. Additionally, these microcapsules exhibited remarkable thermal stability, retaining a minimum of 84.8 % of their stability when exposed to temperatures ranging from 40 to 80 °C. Moreover, during gastric and intestinal digestion, these microcapsules exhibited a high slow-release rate of 44.66 % and 51.6 %, indicating their ability to gradually release calcium contents. The inclusion of dual-frequency ultrasound in the preparation of high calcium microcapsules yielded promising outcomes. Overall, our work presents a novel method for synthesizing corn peptide-chelated calcium microcapsules with desirable properties such as good solubility, excellent thermal stability, and a significant slow-release effect. These microcapsules have the potential to serve as fortified high calcium supplements.

Micro-ECDM Performances Analysis Using Fuzzy Logic and ANFIS During Micro-Channel Fabrication on Silica Glass

Higher accuracy and meticulousness are highly demandable in modern industrial field during micro-machining performances by electrochemical discharge machining (ECDM) process. The paper deals with the experimental fuzzy logic control (FLC) analysis as well as artificial neural network (ANN) and adaptive neuro-fuzzy inference system (ANFIS) analysis during micro-channel fabrication on silica glass. A comparative analysis of FLC, ANN as well as ANFIS has been performed and experimental error prediction has been propounded to estimate minimum error possibilities such as mean absolute error (MAE), root mean square error (RMSE) and regression value (R). Computational time training dataset, minimum sample size and prediction time are also illustrated in this paper. In this paper, ANN, FLC and ANFIS models are analyzed for tool wear rate (TWR) and heat-affected zone (HAZ). 3D Rule Viewer and regression analysis as well as validation of test results and characteristics graph between performances with number of epochs of ANN model also are included in this paper for TWR and HAZ. Influence of process parameters like voltage, duty ratio, pulse frequency and electrolyte concentration on Surface Viewer of TWR and HAZ is also illustrated. It is found that ANFIS has great effectiveness of prediction of error during micro-ECDM process.

Advancing Renewable Energy: An Experimental Study of a Switched-Inductor, Switched-Capacitor Luo Boost Converter for Low-Voltage Applications

Photovoltaic (PV), battery, and fuel cell (FC) technologies are emerging forms of renewable energy gaining popularity. However, one of the key limitations is their production of direct current (DC) voltage, which hinders the connectivity and integration with the electrical grid. To address this issue, various DC/DC boost converters have been introduced. This study presents an innovative Luo converter with a switched-inductor–capacitor (SLC) cell at the input and a switched-capacitor (SC) cell at the output. The SLC cell not only increases the input voltage, but also enhances the source’s lifespan and reliability. The SC cell further amplifies the voltage, especially for high-gain applications. The proposed converter simplifies control processes by using a single power switch, significantly boosting the input voltage by 21 times with a duty ratio of 0.8. This surpasses the gains achieved by conventional boost converters by over fourfold and Luo converters by sevenfold. The second challenge when a converter is connected to these voltage sources is the potential reduction in the lifespan of the sources and the overall system due to large input current ripples. The proposed converter addresses this issue by incorporating a switched-capacitor cell on the input side. This cell charges the inductors in parallel and discharges them in series, reducing the magnitude of the input current. Another advantage of the proposed converter is its simplicity, as it employs only one power switch, minimizing the complexity of the controller system. Additionally, the distribution of the output voltage passing through the diodes between the switch and output capacitor helps mitigate voltage stress for all semiconductor devices and capacitors. The study includes thorough mathematical analyses, simulations, and laboratory tests to validate the research’s theoretical foundations.

Loop gain response to increased cerebral blood flow at high altitude.

To compare loop gain (LG) before and during pharmacological increases in cerebral blood flow (CBF) at high altitude (HA). Loop gain (LG) describes stability of a negative-feedback control system; defining the magnitude of response to a disturbance, such as hyperpnea to an apnea in periodic breathing (PB). "Controller-gain" sensitivity from afferent peripheral (PCR) and central-chemoreceptors (CCR) plays a key role in perpetuating PB. Changes in CBF may have a critical role via effects on central chemo-sensitivity during sleep. Polysomnography (PSG) was performed on volunteers after administration of I.V. Acetazolamide (ACZ-10mg/kg) + Dobutamine (DOB-2-5 μg/kg/min) to increase CBF (via Duplex-ultrasound). Central sleep apnea (CSA) was measured from NREM sleep. The duty ratio (DR) was calculated as ventilatory duration (s) divided by cycle duration (s) (hyperpnea/hyperpnea + apnea), LG = 2π/(2πDR-sin2πDR). A total of 11 volunteers were studied. Compared to placebo-control, ACZ/DOB showed a significant increase in the DR (0.79 ± 0.21 vs 0.52 ± 0.03, P = 0.002) and reduction in LG (1.90 ± 0.23 vs 1.29 ± 0.35, P = 0.0004). ACZ/DOB increased cardiac output (CO) (8.19 ± 2.06 vs 6.58 ± 1.56L/min, P = 0.02) and CBF (718 ± 120 vs 526 ± 110ml/min, P < 0.001). There was no significant change in arterial blood gases, minute ventilation (VE), or hypoxic ventilatory response (HVR). However, there was a reduction of hypercapnic ventilatory response (HCVR) by 29% (5.9 ± 2.7 vs 4.2 ± 2.8 L/min, P = 0.1). Pharmacological elevation in CBF significantly reduced LG and severity of CSA. We speculate the effect was on HCVR "controller gain," rather than "plant gain," because PaCO2 and VE were unchanged. An effect via reduced circulation time is unlikely, as the respiratory-cycle length did not change.

Design and analysis of an improved voltage‐lift‐based extended quadratic gain boost converter with reduced voltage stress across components

SummaryIncreasing the voltage gain of traditional boost converter topologies necessitates an unsustainable increase in the operating duty ratio. Because of their inherent architecture, these topologies are incapable of shielding their individual components from the detrimental effects of extreme duty cycle operation, resulting in increased power loss and inefficient performance. With the objective of attaining a higher voltage gain at a lower duty cycle, this research presents a new quadratic type boost converter derived from an improved voltage‐lift (IVL) cell and the conventional boost converter (CBC). By including an IVL cell in CBC, the voltage conversion ratio is quadratic in nature, and the steady‐state performances are improved over those of CBC. This proposed architecture includes a few new parts, such as capacitors, diodes, and an inductor but no controllable switches, thus the close loop control stays the same. During the entire range of the duty cycle, the proposed boost topology outperforms the conventional quadratic boost converter (CQBC) in terms of dc voltage gain. In addition, the voltage stresses on devices (such as switch and diodes) and intermediate capacitors are reduced compared with CQBC. In steady‐state conditions, the voltage gain and design expressions of the storage elements are determined using time‐domain analysis. The suggested extended quadratic gain boost converter (EQGBC) stands out because of its multiple benefits over existing step‐up converter topologies. The suggested EQGBC has been tested by simulation and hardware implementation to ensure its key performance features. A laboratory‐scaled prototype is developed, which has the capability of boosting the low input voltage of 12 V to a higher value of 48 V at a switching frequency of 100 kHz. The experimental outputs are in close accord with the simulation findings and mathematical analysis.

Fault-tolerant single-input dual-output converter with preserved output under fault operation

DC-DC converters have played an important role in the auxiliary power supply to electric vehicles, DC micro-grids, and portable electronic applications. To reduce the number of components and to improve the power density, multiport DC-DC converters have been recently proposed. Many multi-output converters are designed based on specific operational constraints on duty ratio or inductor currents. Further, simultaneous control of outputs is critical and involves cross-regulation issues. This paper proposes a single-input dual-output (SIDO) DC-DC converter with fault-tolerant circuit configuration to circumvent these challenges. The designed converter is helpful for the simultaneous control of loads by cross-regulation issues and has simple control without any control constraints on duty ratio or inductor currents. The topology proposed in this paper, can most significantly tolerate the failure during open-circuit for single and multiple switches and gives the preserved output voltage under fault case. The effectiveness and feasibility of the proposed configuration is validated using MATLAB/Simulink.

Laminar-type gratings overcoated with carbon-based materials to enhance analytical sensitivity of flat-field emission spectrograph in the VUV region.

Laminar-type spherical diffraction gratings overcoated with carbon-based materials were designed, fabricated, and evaluated for the purpose of enhancing the analytical sensitivity of the flat-field spectrograph in a vacuum ultraviolet region of 35-110 eV. As the design benchmark for numerical calculations, diffraction efficiency (DE) and spectral flux, which are defined by the product of the DE and numerical aperture and correlate with the analytical sensitivity of the spectrograph, were used. To simplify the feasibility study on the overcoating effects, we assumed a laminar-type grating having a grating constant of 1/1000 mm and coated with a Au layer of 30.0 nm thickness and an incidence angle of 84.0°. The optimized groove depth and duty ratio were 30.0 nm and 0.3, respectively. In addition, the optimum thicknesses of the overcoating layer were 44, 46, 24, and 30 nm for B4C, C, diamond-like-carbon, and SiC, respectively. Based on these results, we have fabricated a varied-line-spacing holographic grating overcoated with B4C with a thickness of 47 nm. For the experimental evaluation, we used the light source of Mg-L and Al-L emissions excited by the electron beam generated from an electron microscope, an objective flat-field spectrograph, and a CCD imaging detector. The experimental results showed that the spectrograph employing a new grating overcoated with the B4C layer indicated almost the same spectral resolution and 2.9-4.2 times higher analytical sensitivity compared with those obtained with a previously designed Au-coated grating having a grating constant of 1/1200 mm and used at an incidence of 86.0°.

Nitrogen-containing diamond-like carbon deposited on glass substrate via filtered cathodic vacuum arc with high-frequency pulsed DC substrate bias

This research investigates the properties of nitrogen-containing diamond-like carbon (N-DLC) coatings deposited on glass substrate using a high-frequency pulsed-DC substrate bias. The study involved comprehensive investigations to understand how variations in carbon bonding affect the properties of N-DLC coatings. By adjusting the voltage, frequency and duty ratio of the pulsed bias, it was possible to deposit an optical coating with a transmittance of up to 52 % at range of 800–2500 nm while effectively preventing the peeling of the DLC coating on the glass. With increasing the clustered graphite structure in the DLC coating, the sheet resistance was lowered from 2370 kΩ/□ to 36 kΩ/□, and the electrical properties were also improved. The findings provide valuable insights for optimizing N-DLC coatings for non-conductors, e.g., glass, rubber, polymer, and engineering ceramic.

THD analysis and small AC signal analysis of trans-Z-source and quasi-Z-source inverter for linear and non-linear load

The paper primarily focuses on the ongoing research related to Z source inverter technologies (ZSITs) used in the transportation industry, particularly for electric vehicles (EVs) and hybrid electrical vehicles (HEVs). It analyzes various topologies of ZSITs based on their mode of operation, capacitor voltage stress during active states and non-active state operations, DC link voltage before inverter module and line to line output voltage across the load. The paper compares the conventional trans-z source and two port quasi-Z source inverter model networks for multiple parameters and derives mathematical equations for both linear and non-linear loads. Practical and theoretical calculations match when using a modulation index of M=0.85 and a duty ratio of 1.414. The result obtained in this paper indicates that the proposed solution is better in terms of reduction in total total harmonics distortions (THD) percentage of 18.14% during the transition condition. All the analysis has been carried out with MATLAB based Simulink model.

Model Predictive Control With Duty Ratio Modulation for Open-Winding PMSM Drives With Common DC Bus

Model Predictive Control With Duty Ratio Modulation for Open-Winding PMSM Drives With Common DC Bus

Adjustable High-Power Light Emitting Diode Driving Circuit and Its Lighting Application in Sports Venues

High-power LED not only has the characteristics of energy saving, environmental protection, long service life, and high reliability, but also has the advantages of high light efficiency and large conduction current. According to the characteristics of high-power LED, an adjustable high-power LED driving circuit is designed in this study. The chip adopts the Boost circuit structure driven by constant current, and the output current on a single channel is converted into voltage by using the sampling resistor on the LED path and fed back to the circuit. After passing a mirror current independent of temperature through a resistor, the reference voltage source is obtained by voltage division. When designing the LDO circuit of voltage regulator, modules such as front-end voltage conversion circuit and input under voltage protection circuit are added. When designing the soft start circuit, the output voltage of the soft start replaces the output of the error amplifier and is connected to one end of the PWM comparator. In the design of dimming circuit, PWM dimming technology is adopted, and the DIM pin is connected to low level when there is no PWM signal. In the experiment, the lowest level of soft start is 0.78 V, the highest bit is 1.35 V, and the period is 374.6 us. When VIN = 8 V, the output voltage can be adjusted to 40 V in one period based on soft start, which meets the starting requirements of the driving circuit. When the DIM pin is connected with a PWM dimming signal with a duty ratio of 90% and a frequency of 10 kHz, the output current of the LED light is in a relatively stable state. Applying the designed LED driving circuit to the lighting of sports venues can meet the requirements of daily events and training, and has advantages in energy saving and environmental protection.

Switched-Capacitor-Based Hybrid Clamped Converter for Wide Power Factor Applications

The clamped multilevel converter generally adopts the zero-sequence voltage injection method to realize the voltage balancing of the DC link capacitors. However, the relationship between the reference modulation voltage and the duty ratio of phase neutral point current is often a triangle or trapezoidal function. When the power factor is low, the required optimal zero-sequence voltage will be out of bounds, which will lead the capacitor voltage ripples to become larger or even divergent. Therefore, a novel switched-capacitor-based hybrid clamped(SCB-HC) converter is proposed in this article. The new redundant switching states are obtained by introducing the boost characteristics of the switched-capacitor(SC) circuit. And a hybrid phase-shifted pulse width modulation(PS-PWM) is developed to extend its functional relationship. This ensures the peak current that flow out of the neutral points is fewer, then the capacitor voltage drift is reduced significantly. Moreover, the proposed hybrid PS-PWM method not only ensures that SC circuit switches series and parallel patter once during a carrier period, but also achieves the voltage balancing of SC and DC link midpoint capacitor naturally under ideal conditions. On top of that, the capacitor voltage balancing method is designed to ensure independent and decoupled control of all capacitor voltages. Simulations and experiments show that the proposed topology, modulation method and voltage control method are practical and feasible for wide power factor applications.

Optimal Duty Ratio Assisted PFM Control for VHF Isolated Class E DC-DC Converter

Optimal Duty Ratio Assisted PFM Control for VHF Isolated Class E DC-DC Converter

The dynamics of actin protrusions can be controlled by tip-localized myosin motors

Class III myosins localize to inner ear hair cell stereocilia and are thought to be crucial for stereocilia length regulation. Mutations within the motor domain of MYO3A that disrupt its intrinsic motor properties have been associated with non-syndromic hearing loss, suggesting that the motor properties of MYO3A are critical for its function within stereocilia. In this study, we investigated the impact of a MYO3A hearing loss mutation, H442N, using both in vitro motor assays and cell biological studies. Our results demonstrate the mutation causes a dramatic increase in intrinsic motor properties, actin-activated ATPase and in vitro actin gliding velocity, as well as an increase in actin protrusion extension velocity. We propose that both “gain of function” and “loss of function” mutations in MYO3A can impair stereocilia length regulation, which is crucial for stereocilia formation during development and normal hearing. Furthermore, we generated chimeric MYO3A constructs that replace the MYO3A motor and neck domain with the motor and neck domain of other myosins. We found that duty ratio, fraction of ATPase cycle myosin is strongly bound to actin, is a critical motor property that dictates the ability to tip localize within filopodia. In addition, in vitro actin gliding velocities correlated extremely well with filopodial extension velocities over a wide range of gliding and extension velocities. Taken together, our data suggests a model in which tip-localized myosin motors exert force that slides the membrane tip-ward, which can combat membrane tension and enhance the actin polymerization rate that ultimately drives protrusion elongation.

Design of non‐isolated DC‐DC converter using renewable energy source for two‐stage centralized grid connected inverters

SummaryRecent research has focused on high‐power two‐stage photovoltaic (PV) systems, particularly with the introduction of wideband gap silicon carbide (SiC) devices. A massive inductor or interleaved boost converter is utilized in a standard two‐stage system, requiring a significantly larger number of components and subsequently impacting power density. As a result, the purpose of this research is to provide a topology for a high‐power non‐isolated switched capacitor network‐integrated boost converter (SCNIBC). This architecture employs two of every switch/diode/inductor and capacitor. The suggested architecture has a triple voltage boost at 50% duty ratio, excellent efficiency, and very low inrush current. A suitable analysis is performed to determine the voltage gain, component selection, and power loss analysis. Reliability analysis is studied as per the IEC 61709‐2017 standards. A fair comparison with existing state‐of‐the‐art high‐power PV system topologies is offered. Eventually, the steady‐state experimental findings for a 2.5 kW load are confirmed. The results are also validated for a step adjustment in input voltage from 80 V to 96 V. Lastly, the grid connected operation of converter is studied with a H‐bridge inverter under unity, lagging and leading power factors.

Bioinspired Double-Broadband Switchable Microwave Absorbing Grid Structures with Inflatable Kresling Origami Actuators.

Tunable radar stealth structures are critical components for future military equipment because of their potential to further enhance the design space and performance. Some previous investigations have utilized simple origami structures as the basic adjusting components but failed to achieve the desired broadband microwave absorbing characteristic. Herein, a novel double-broadband switchable microwave absorbing grid structure has been developed with the actuators of inflatable Kresling origami structures. Geometric constraints are derived to endow a bistable feature with this origami configuration, and the stable states are switched by adjusting the internal pressure. An ultra-broadband microwave absorbing structure is proposed with a couple of complementary microwave stealth bands, and optimized by a particle swarm optimization algorithm. The superior electromagnetic performance results from the mode switch activating different absorbing components at corresponding frequencies. A digital adjusting strategy is applied, which effectively achieves a continuously adjusting effect. Further investigations showthat the proposed structure possesses superior robustness. In addition, minimal interactions are found between adjacent grid units, and the electromagnetic performance is mainly related to the duty ratio of the units in different states. They have enhanced the microwave absorbing performance of grid structures through a tunable design, a provided a feasible paradigm for other tunable absorbers.

Einsatz von Shutter-Brillen im Tennis – Einfluss von (Bild-)Frequenz und Dunkelphasenanteil auf die Zielschlagpräzision

Purpose. The use of shutter glasses for perception training in sports requires knowledge of adequate load dosage. The study analyses the influence of (image-)frequency or “duty ratio” (dark phase percentage) on target stroke accuracy in tennis. Material and Methods. With a total number of 22 tennis players (18m, 4f, mean age = 23.6, SD = ± 2.7 years) the target hit precision was conducted. The tennis players had to return the balls played to them by a ball machine using the forehand volley and to make direct hits to a bull’s eye (high scores = high target hit precision). The results with different (randomised) conditions (strobe rates level II = 5.3 Hz, level V = 2.3 Hz, lev- el VIII = 1.0 Hz; dark phase level II = 88 ms, level V = 341 ms, level VIII = 909 ms) of currently used shutter glasses (Nike Vapor Strobe) and without occlusion have been compared. Keywords intermittent vision, stroboscopic visual training, shutter lens glasses, sports vision training, tennis

Maximum Power Point Tracking with Incremental Conductance and Fuzzy Logic Controller in Solar Energy Systems

Energy benefits both individuals and nations. Humanity's reliance on fossil fuels an inability to respond increases depletion. Energy supplies are rapidly decreasing. Electricity use causes the energy crisis. Sustainable energy largely meets the energy demand of the growing population. In addition, it benefits the environment by reducing carbon emissions. This situation sustainable energy sources have supplemented traditional energy sources and promoted sustainable energy use. Solar, wind, and fuel cell energy are given example of sustainable energy. Power generating facilities are employed nowadays because of their extended lifespan, inexpensive maintenance, no hazardous waste, and independence from dwindling energy sources. Solar power generation depends on environmental circumstances, hence MPP generation must be observed. MPPT follow solar panel highest MPP. This study involves a system is comprised by a DC-DC boost converter, PV panel, and a ohmic load. The duty ratio is generated by the IC and FLC MPPT algorithms, and the PWM signal is generated by comparing it with the triangle wave. This generated signal is applied to the DC-DC boost converter. The aim of this research is to investigate the effectiveness, variability, and duration required to attain the MPP of the implemented MPPT methods. The system has been developed within the MATLAB/Simulink framework. Based on the findings of the simulation, it has been determined that the FLC MPPT algorithm achieves the MPP at a faster rate compared to the IC MPPT algorithm. Consequently, the level of fluctuation is minimum and the efficiency is high.

Study on the Influence of Coil Arrangement on the Output Characteristics of Electromagnetic Galloping Energy Harvester.

The arrangement of the induction coil influences the electromagnetic damping force and output characteristics of electromagnetic energy harvesters. Based on the aforementioned information, this paper presents a proposal for a multiple off-center coil electromagnetic galloping energy harvester (MEGEH). This study establishes both a theoretical model and a physical model to research the influence of the position and quantity of the induction coils on the output characteristics of an energy harvester. Additionally, it conducts wind tunnel tests and analyzes the obtained results. With the increase in the number of induction coils, there is a significant improvement in the duty cycle and output power of the MEGEH, resulting in an amplified energy conversion efficiency. At a wind speed of 9 m/s, the duty ratios of a single set of coils (SC), two sets of coils (TC), and multiple sets of coils (MC) are 30%, 51%, and 100%, respectively. The total output powers are 0.4 mW, 0.62 mW, and 0.72 mW. However, the rate of output growth has decreased from 55% to 16%. The position of the coils affects the initial electromagnetic damping of the energy harvester. Changing the position can reduce the initial electromagnetic damping, thereby decreasing the critical wind speed. The critical wind speed of the MEGEH decreases as the induction coil is positioned further away from the vibration center. When the distance is sufficiently large, the electromagnetic damping force becomes negligible. When the induction coil is positioned centrally, the MEGEH demonstrates its maximum critical wind speed, which has been measured at 4.01 m/s. When the initial distance between the induction coil and the vibrating component is increased to 10 mm, the critical wind speed reaches its minimum value of 2.23 m/s. Therefore, it is necessary to optimize the arrangement of the coils. The coils of the MEGEH should be arranged with the MC and a 10 mm offset from the center.

Transparent ultrawideband polarization-insensitive absorber with optimal thickness based on a grid ITO structure

With the large-scale commercialization of broadband wireless communication technologies, interference between spatial electromagnetic waves (EMWs) is becoming increasingly serious. As devices for solving electromagnetic interference (EMI) problems, microwave absorbers (MAs) have become increasingly mature with the rapid development of artificial electromagnetic structures. However, current MAs still face challenges in terms of wideband absorption, wide-angle absorption, thickness, etc., which limits their application scenarios. Therefore, this paper proposes a transparent ultrawideband polarization-insensitive absorber based on a grid indium tin oxide (ITO) structure. This design adopts a multilayer structure with a total thickness of 3.525 mm (0.114λ L ), close to the predicted minimum thickness, to expand the bandwidth. The grid-patterned ITO film resonant structure and ITO film ground plane are designed to further improve optical transmittance by increasing duty ratios. Simulation results demonstrate over 90% absorption from 9.7 GHz to 69.2 GHz, with a fractional bandwidth (FBW) of 150.8%. The absorber has good incident angle stability and polarization insensitivity. When the incident angle varies within 0-60°, the proposed absorber maintains an absorption close to 80% over an ultrawideband range, and the absorption remains nearly constant when the polarization angle changes from 0° to 90°. The fabricated sample shows a visible light transmittance of approximately 73.2%, and shows an absorption performance consistent with simulations in the 6-38 GHz frequency range, validating the effectiveness of the proposed design. Due to its transparent, ultrawideband absorption, wide incident angle stability and polarization insensitivity properties, this proposed absorber has important guiding significance for applications in high-frequency transparent electronics, radars, communications systems and other devices working in the microwave frequency band.