Test Duration Research Articles

The Audible Contrast Threshold (ACT) test: A clinical spectro-temporal modulation detection test

Over the last decade, multiple studies have shown that hearing-impaired listeners’ speech-in-noise reception ability, measured with audibility compensation, is closely associated with performance in spectro-temporal modulation (STM) detection tests. STM tests thus have the potential to provide highly relevant beyond-the-audiogram information in the clinic, but the available STM tests have not been optimized for clinical use in terms of test duration, required equipment, and procedural standardization. The present study introduces a quick-and-simple clinically viable STM test, named the Audible Contrast Threshold (ACT™) test. First, an experimenter-controlled STM measurement paradigm was developed, in which the patient is presented bilaterally with a continuous audibility-corrected noise via headphones and asked to press a pushbutton whenever they hear an STM target sound in the noise. The patient's threshold is established using a Hughson-Westlake tracking procedure with a three-out-of-five criterion and then refined by post-processing the collected data using a logistic function. Different stimulation paradigms were tested in 28 hearing-impaired participants and compared to data previously measured in the same participants with an established STM test paradigm. The best stimulation paradigm showed excellent test-retest reliability and good agreement with the established laboratory version. Second, the best stimulation paradigm with 1-second noise “waves” (windowed noise) was chosen, further optimized with respect to step size and logistic-function fitting, and tested in a population of 25 young normal-hearing participants using various types of transducers to obtain normative data. Based on these normative data, the “normalized Contrast Level” (in dB nCL) scale was defined, where 0 ± 4 dB nCL corresponds to normal performance and elevated dB nCL values indicate the degree of audible contrast loss. Overall, the results of the present study suggest that the ACT test may be considered a reliable, quick-and-simple (and thus clinically viable) test of STM sensitivity. The ACT can be measured directly after the audiogram using the same set up, adding only a few minutes to the process.

Evaluation and Development of Analytical Procedures to Assess Buffering Capacity of Carbonate Ruminant Feed Buffers.

The inclusion of rumen buffers in ruminant feeds has gained widespread adoption for the prevention of rumen acidosis, thereby avoiding the negative production and health consequences of low rumen pH and resulting in improved feed efficiency. Benchmarking and quality controlling the performance of rumen buffer materials is of significant interest to feed mills and end-user producers. The aim of this study was to evaluate, develop and optimise a laboratory protocol to consistently and robustly evaluate rumen buffering materials in order to predict their in vivo efficacy. Three different methods were evaluated for determining the buffering potential of carbonate buffer materials: (a) 2 and 8 h static pH, (b) 8 h fixed HCl acid load addition and (c) 3 h acidotic diet simulation using acetic acid. Buffer material, threshold pH, test duration and interactions between all three variables were significant (p < 0.001) in evaluating the performance of the buffer materials. The acidotic diet simulation was found to provide a different ranking of materials to the 8 h fixed HCl acid load methodology. The results highlight the importance of method selection and test parameters for accurately evaluating the potential efficacy of rumen buffer materials.

Exploring Low Temperature Proton Exchange Membrane Water Electrolysis Anode Catalyst Degradation Under Cathode Backpressure Conditions

Hydrogen is expected to play an important role in the decarbonization of the future energy landscape by integrating renewable, nuclear, and fossil fuels and using excess power from the grid to produce H2 that can then be stored and used for a variety of applications ranging from ammonia and steel production, stationary power, buildings, and transportation.1 In order to achieve low-cost hydrogen production that is competitive with steam methane reformation (SMR), it is necessary to decrease the capital cost and this can be done by leveraging variable renewable energy (VRE) as an electricity feedstock for LTE.2 However, cost, and durability are still current challenges in state-of-the art water electrolysis systems. More research is needed to better understand the effects of dynamic operation on electrolyzer degradation. Understanding the degradation mechanisms governing intermittent electrolysis operation can enable future improvements related to component design and system operation.In recent years, electrolyzer anode degradation has been investigated during continual intermittent operation at the single cell level. Square-wave potential cycling demonstrated higher anode degradation compared to the triangle-wave cycling over the same 525 hour test (21.9 d).3 Electrolyzers operating at differential pressures and producing electrochemically compressed hydrogen could decrease the hydrogen production cost by eliminating the need for equipment related to mechanical compression.4 This work investigates the dynamics of low-temperature proton exchange membrane (PEM) electrolyzers, with a specific focus on anode catalyst layer degradation from redox transition when subjected to hydrogen crossover from cathode backpressure conditions. While cathode backpressure and operation requirements are well understood from an industry perspective, its impact on degradation mechanisms and loss rates has been relatively underexplored when low-temperature electrolysis is focused on cost reduction and variable load.In this study, hydrogen cross-over rates were varied by cathode backpressure conditions (ambient to 30 Bar) and were compared to elucidate the impact hydrogen has on anode catalyst layer degradation. The durability test duration varied from 168 – 500+ hrs. Hydrogen cross-over rates were found to correlate to cell potential during operational shutdowns and loss rates during load cycling. Electrochemical impedance spectroscopy further demonstrates higher degrees of kinetic loss and the immergence of additional loss mechanisms. The findings presented in this research contribute to the fundamental understanding of low-temperature PEM electrolysis dynamics under cathode backpressure conditions. The implications of this research offer practical insights for the design and operation of efficient and durable electrolysis systems crucial for the advancement of sustainable hydrogen production technologies.(1) H2@Scale. Hydrogen and Fuel Cell Technologies Office. https://www.energy.gov/eere/fuelcells/h2scale.(2) Mark, R.; Jadun, P.; Gilroy, N.; Connelly, E.; Boardman, R.; Simon, A. J.; Elgowainy, A.; Zuboy, J. The Technical and Economic Potential of the H2@Scale Concept within the United States; NREL/TP-6A20-77610; National Renewable Energy Laboratory: Golden, CO, 2020.(3) Alia, S. M.; Reeves, K. S.; Yu, H.; Park, J.; Kariuki, N.; Kropf, A. J.; Myers, D. J.; Cullen, D. A. Electrolyzer Performance Loss from Accelerated Stress Tests and Corresponding Changes to Catalyst Layers and Interfaces. Journal of The Electrochemical Society 2022, 169 (5), 054517. https://doi.org/10.1149/1945-7111/ac697e.(4) Ragnhild Hancke, Thomas Holm, and Øystein Ulleberg, “The Case for High-Pressure PEM Water Electrolysis,” Energy Conversion and Management 261 (2022): 115642, https://doi.org/10.1016/j.enconman.2022.115642. Figure 1

Face validity and washback effects of the shortened PTE Academic: insights from teachers in Mainland China

Pearson Test of English Academic (PTE Academic), a high-stakes English language proficiency test, underwent substantial revisions in 2021. The test duration was reduced from 3 h to 2 h by reducing specific task numbers and sections. This study investigates the impact of these changes on teachers’ perceptions and teaching practices, areas previously underexplored in language assessment literature. It focuses on the implications of the test’s modifications, examining the face validity and washback effects through the lens of teachers in mainland China. Semi-structured interviews with four experienced PTE Academic test trainers, who were familiar with both the original and revised test formats, reveals that the revised PTE Academic is perceived to maintain strong face validity, particularly noted in its academic authenticity, balanced skill structure, and perceived result accuracy. Additionally, most teachers perceived an increase in test difficulty. A mixed washback effect was observed: while improvements in students’ language competence—a positive outcome—were noted, teachers also reported a continued reliance on teaching test-oriented strategies for higher-scoring tasks, indicating negative washback. This study highlights the significant implications of reducing PTE Academic’s duration and offers targeted recommendations for its future improvement. These suggestions aim to enhance students’ academic language skills, thereby better aligning PTE Academic with the practical language abilities required in university settings.

Relationship between minerals, vitamins and sports ability of dance athletes

Vitamins and minerals are essential for regulating metabolism. According to the nature of sports, athletes can take multi vitamin and mineral supplements to enhance some important metabolic processes and improve sports performance. The purpose of this study is to explore the effects of minerals and vitamins on the sports ability of dance athletes. In this study, 100 professional dancers were randomly divided into the experimental group and the control group by the control variable method. The sports diet and water of the experimental group were supplemented with certain vitamins and minerals. After that, the athletes were trained and tested, including 12 min running, strength test and dance training duration test. The results showed that the 12 min running distance of the experimental group was 420 m more than that of the control group, the balance time was 16 min longer, and the strength was increased by 25 N. In the overall energy comparison, the energy and endurance of the experimental group was two hours more than that of the control group. The conclusion is that minerals and vitamins play a role in promoting and subsidizing the physical fitness of athletes, which are more prominent in endurance and strength. This study provides a certain value for the effect of nutrients on athletes’ ability.

Microstereolithography-fabricated microneedles for fluid sampling of histamine-contaminated tuna

A custom-designed microneedle sampling system was prepared using dynamic mask microstereolithography; this sampling system was used for determination of histamine content in fresh, histamine-spiked, and spoiled tuna flesh. Lateral flow (test strip) assays were successfully utilized in the microneedle sampling system to assess histamine content. Good agreement was noted between data obtained from the microneedle sampling system and a commercially available histamine detection kit. A discrepancy was noted in the results from the microneedle sampling system and the commercially available histamine detection kit at low (negative) levels of histamine. There was an improvement in the agreement between the microneedle sampling system and the commercially available histamine detection kit at higher histamine levels. The results, which showed an improvement in the test duration and the amount of reagent needed for histamine detection, indicate the promise of printed microneedle sampling systems for histamine detection in seafood samples and other types of food testing.

Glaucoma Home Self-Testing Using VR Visual Fields and Rebound Tonometry Versus In-Clinic Perimetry and Goldmann Applanation Tonometry: A Pilot Study.

This pilot study aimed to assess the feasibility, accuracy, and repeatability of unsupervised, at-home, multi-day glaucoma testing using the Olleyes VisuALL Virtual Reality Platform (VRP) and the iCare HOME handheld self-tonometer. Participants were trained to use two U.S. Food and Drug Administration-registered or approved devices before conducting self-tests at home over 3 consecutive days. The iCare HOME intraocular pressure (IOP) measurements were collected four times daily per eye, and VRP visual field tests were performed once daily. The results were compared with one in-clinic Humphrey Field Analyzer (HFA) visual field test performed on the day of device training, iCare HOME measurements by the trainer, and the last five Goldmann applanation tonometer (GAT) results. Of 15 enrolled participants, nine of them (60%) completed the study. The six excluded participants could not self-measure using iCare HOME. There was significant correlation between the average mean deviation (MD) values of the at-home VRP tests and in-clinic HFA test (r2 = 0.8793, P < 0.001). Additionally, the average of the sensitivities in five of six Garway-Heath sectors were significantly correlated. VRP test duration was also shorter than in-clinic HFA testing (P < 0.001). Finally, at-home tonometry yielded statistically similar values compared to trainer-obtained iCare HOME values. The mean and range of at-home tonometry were also statistically similar to those for in-clinic GAT, but at-home tonometry demonstrated higher maximum IOP values (P = 0.0429). Unsupervised, at-home, multi-day glaucoma testing using two devices resulted in the capture of higher maximum IOPs than in the clinic and good MD correlation of VRP with HFA. However, 40% of participants could not self-measure IOP using iCare HOME. The study findings suggest that at-home remote glaucoma monitoring correlates with in-office testing and could provide additional information for glaucoma management, although patients had more difficulty with the iCare HOME than the VRP.

Relationship between NT-proBNP, echocardiographic abnormalities and functional status in patients with subclinical siabetic cardiomyopathy

IntroductionPersons with diabetes are at risk for developing a cardiomyopathy through several pathophysiological mechanisms independent of traditional risk factors for heart failure. Among those with diabetic cardiomyopathy (DbCM), the relationship between natriuretic peptides, cardiac structural abnormalities and functional capacity is largely unknown.MethodsIn this prespecified subgroup analysis of the Aldose Reductase Inhibition for Stabilization of Exercise Capacity in Heart Failure (ARISE-HF) trial, 685 participants with asymptomatic DbCM underwent baseline echocardiography data, laboratory investigations, and functional assessments. Participants were stratified by N-terminal pro-B type natriuretic peptide (NT-proBNP) quartiles, and correlation with echocardiographic and functional parameters were assessed using Spearman correlation test.ResultsThe median NT-proBNP was 71 (Q1, Q3: 33, 135) ng/L. No association was observed between NT-proBNP concentrations and echocardiographic parameters of either diastolic or systolic dysfunction including global longitudinal strain, left ventricular ejection fraction, left ventricular mass index, left atrial volume index, E/E’, or right ventricular systolic pressure. In contrast, NT-proBNP was significantly correlated with overall Kansas City Cardiomyopathy Questionnaire score (rho = − 0.10; p = 0.007), the Physical Activity Scale in the Elderly (rho = − 0.12; p = 0.004), duration of cardiopulmonary exercise testing (rho = − 0.28; p < 0.001), peak VO2 (rho = − 0.26; p < 0.001), and ratio of minute ventilation/carbon dioxide production (rho = 0.12; p = 0.002). After adjustment for known confounders, the correlation with Physical Activity Scale in the Elderly and overall Kansas City Cardiomyopathy Questionnaire score was no longer significant.ConclusionAmong patients with subclinical DbCM, elevated NT-proBNP concentrations are associated with worse health status, lower activity levels, and reduced functional capacity, but not with cardiac structural abnormalities. These findings suggest that regardless of cardiac structural abnormalities, biomarker concentrations reflect important deterioration in functional capacity in affected individuals.Trial registrationARISE-HF, NCT 04083339 Date Registered August 23, 2019.Graphical abstractAbnormal ECHO defined as Myocardial Global Longitudinal Strain < − 16 or left ventricular mass index > 95 for females or > 115 for males or E/e’ >13 or left atrial volume index > 34. †Normal ECHO is defined as the absence of these abnormalities. Low NT-proBNP is defined as < 71 ng/L while high NT-proBNP is defined as ≥ 71 ng/L.

Comparative Analysis of 24-2C, 24-2, and 10-2 Visual Field Tests for Detecting Mild-Stage Glaucoma With Central Visual field Defects

This study sought to identify the most effective testing program for detecting visual-field defects in mild-stage glaucoma with central visual-field defects. A multicenter, retrospective diagnostic testing evaluation. The study involved 93 eyes (83 patients) with mild-stage glaucoma (median mean deviation [interquartile range]: -1.79 [2.16] dB) with central visual-field defects and 69 eyes (63 patients; median mean deviation, -1.38 [2.31] dB) with mild-stage glaucoma without central visual-field defects, from Jikei University School of Medicine and Tajimi Iwase Eye Clinic. Patients underwent 10-2 Swedish Interactive Thresholding Algorithm (SITA) Standard, 24-2 SITA Standard, and 24-2C SITA Faster tests. Central visual-field defects were defined using 10-2 SITA Standard and optical coherence tomography (OCT). A detection power of 4 points in the 24-2 that coincided with 10-2 (Center4), 12 points that lie within 10° (24-2-12), and 22 points that lie within 10° of 24-2C (24-2C-22) were analyzed using receiver operating characteristic (ROC) curves based on logistic regression analysis, using total deviation (TD) and pattern deviation (PD) probability plots. Area under the receiver operating characteristic curve (AUC) of the Center4, 24-2-12, and 24-2C-22 tests. In the upper-central visual field, AUCs of the TD plot were 0.50 (0.40-0.58) for the Center4, 0.75 (0.67-0.83) for 24-2-12, and 0.85 (0.78-0.91) for 24-2C-22, with 24-2C-22 AUC significantly exceeding 24-2-12 AUC. For the PD plot, AUCs were 0.53 (0.44-0.63), 0.81 (0.74-0.89), and 0.84 (0.77-0.90), respectively. In the lower-central visual field, using a total plot, AUCs were 0.27 (0.18-0.36), 0.57 (0.47-0.69), and 0.57 (0.46-0.68) for the Center4, 24-2-12, and 24-2C-22, respectively. Using the PD plot in the upper field, AUCs were 0.27 (0.19-0.36), 0.64 (0.53-0.75), and 0.81 (0.72-0.90), respectively, with the AUC of the 24-2C-22 significantly exceeding that of 24-2-12. The 24-2C test was significantly faster than both the 24-2 and 10-2 tests, reducing testing duration by 46% and 52%, respectively. The 24-2C SITA Faster test is highly effective and efficient for detecting mild-stage glaucoma with central visual-field defects. This, and its reduced duration, makes it a valuable tool in clinical settings.

Development of high hard TiB–TiB2 coatings on Ti implants for bio-tribological applications; applying Box-Behnken design and actual wear analyzing in simulated body fluids

This research focuses on the enhancement of the tribological behavior of commercial pure titanium (Cp-Ti) in a simulated body fluid (SBF) via surface reinforcement by titanium borides. The protective boride coatings were formed through the pack cementation process at two different temperatures (950 and 1050 °C) to create diverse hard compositions of TiB and TiB–TiB2 in the coating, with hardness of 1032 and 1291 Hv, respectively. The roughness and wettability of top surfaces were evaluated before the tribology studies due to their impacts on the tribology behavior. Box-Behnken design (BBD) was applied to investigate the effects of the wear parameters in dry and SBF environments. The duration of the wear tests was 53, 35, and 26 min for low, medium, and high speed. It was found that the abrasion wear type was dominant at the beginning of sliding, and then changed to the plastic deformation in the dry conditions, while there is no sign of the abrasion and adhesion wear features at the surface of the reinforced samples abraded in the SBF solution. Results confirmed a high coincidence between BBD predictions and actual findings. The released debris from the coatings was also investigated to find origins. Results showed that majority of the debris in the SBF solution belonged to the calcium phosphate particles demonstrating the bioactivity of the TiB–TiB2 coatings. According to findings, hard TiB–TiB2 coatings could significantly improve the tribological behavior of the Ti implants, which could in turn result in expanding the biological application of Cp-Ti.

Persistent methicillin-resistant Staphylococcus aureus (MRSA) nares test positivity during initial days of systemic antistaphylococcal antimicrobial therapy

The typical duration of positive nucleic acid tests for methicillin-resistant Staphylococcus aureus (MRSA) in the nares of patients receiving systemic anti-MRSA antimicrobials is unknown. In this study, hospitalized adult patients with an initial positive MRSA nares nucleic acid test prescribed systemic anti-MRSA antimicrobials had follow-up testing done 48 to 96hours later. A positive follow-up test was detected in 100/113 (88.5%), indicating that MRSA nares DNA tests still have utility for screening after patients have initiated anti-MRSA therapy.

Machine Learning Allowed Interpreting Toxicity of a Fe-Doped CuO NM Library Large Data Set─An Environmental In Vivo Case Study.

The wide variation of nanomaterial (NM) characters (size, shape, and properties) and the related impacts on living organisms make it virtually impossible to assess their safety; the need for modeling has been urged for long. We here investigate the custom-designed 1-10% Fe-doped CuO NM library. Effects were assessed using the soil ecotoxicology model Enchytraeus crypticus (Oligochaeta) in the standard 21 days plus its extension (49 days). Results showed that 10%Fe-CuO was the most toxic (21 days reproduction EC50 = 650 mg NM/kg soil) and Fe3O4 NM was the least toxic (no effects up to 3200 mg NM/kg soil). All other NMs caused similar effects to E. crypticus (21 days reproduction EC50 ranging from 875 to 1923 mg NM/kg soil, with overlapping confidence intervals). Aiming to identify the key NM characteristics responsible for the toxicity, machine learning (ML) modeling was used to analyze the large data set [9 NMs, 68 descriptors, 6 concentrations, 2 exposure times (21 and 49 days), 2 endpoints (survival and reproduction)]. ML allowed us to separate experimental related parameters (e.g., zeta potential) from particle-specific descriptors (e.g., force vectors) for the best identification of important descriptors. We observed that concentration-dependent descriptors (environmental parameters, e.g., zeta potential) were the most important under standard test duration (21 day) but not for longer exposure (closer representation of real-world conditions). In the longer exposure (49 days), the particle-specific descriptors were more important than the concentration-dependent parameters. The longer-term exposure showed that the steepness of the concentration-response decreased with an increased Fe content in the NMs. Longer-term exposure should be a requirement in the hazard assessment of NMs in addition to the standard in OECD guidelines for chemicals. The progress toward ML analysis is desirable given its need for such large data sets and significant power to link NM descriptors to effects in animals. This is beyond the current univariate and concentration-response modeling analysis.

Investigation of high-performance alkali-activated slag concrete-filled steel tubular members under lateral impact

This paper studied the behaviour of High-performance Alkali-activated slag Concrete-Filled Steel Tubular members under transverse impact along with axial compression. Combining alkali-activated slag concrete with concrete-filled steel tubes provides a novel composite material incorporating the benefits of alkali-activated slag concrete and steel tubes. Alkali-activated slag concrete, known for its environmentally beneficial traits compared to traditional concrete, improves sustainability, while concrete-filled steel tube increases structural stability. Seven specimens composed of one hollow tube and six high-performance alkali-activated slag concrete-filled steel tubular specimens were tested using a drop hammer test setup to enhance our understanding of the structural performance of high-performance alkali-activated slag concrete-filled steel tubular members. A finite element analysis model was then established to broadly compare the impact resistance of circular high-performance alkali-activated slag concrete-filled steel tubular members. The mid-span displacement and impact test durations of specimens subjected to lateral impact and axial compression were assessed using a high-speed video camera called Phantom V411. This analysis includes the examination of maximum impact load, impact plateau value, maximum displacement, residual displacement, indentation, impact duration and strain responses, and an investigation into the failure modes of the specimens. The obtained results closely align with the experimental outcomes, indicating the effectiveness of the FEA model in predicting the behaviour of circular high-performance alkali-activated slag concrete-filled steel tubular members.

Uncertainty of the initial phase estimation of a sinewave in the presence of phase noise, additive noise or jitter

This paper presents the derivation of a simple analytical expression for the precision of the initial phase estimates obtained through a least-squares procedure. That expression depends on number of samples, phase noise standard deviation and additive noise standard deviation. This study is applicable to the estimates obtained through the sine fitting algorithm with known frequency and to the Discrete Fourier Transform algorithm. The analytical expression supplied was verified using a Monte Carlo simulation with numerically created data. The non-ideal phenomena treated in this work is the presence of jitter in the sampling instant, phase noise in the oscillator and additive noise in the system both of which must be normally distributed with a known value of standard deviation. It is useful information for an engineer in order to choose the proper number of samples to acquire to achieve a desired level of precision on the estimates made and thus carry out an efficient data acquisition with no unnecessary samples thus optimizing the test duration.

The effects of baicalin in depression: preclinical evidence construction based on meta-analysis.

Depression manifests as a mental disorder characterized by a low mood, suicidal tendencies, disturbances in sleep-wake cycles, psychomotor agitation, and pronounced feelings of hopelessness and anhedonia. Baicalin, a natural flavonoid compound, shows significant promise in alleviating depressive symptoms in animals. This study aims to assess the impact of baicalin on experimental models of depression. A systematic search of electronic databases was conducted using the search terms "baicalin" AND "depression" OR "depressed" OR "anti-depression". Preclinical animal models representing experimental depression were included in the analysis. The risk of bias in the included studies was evaluated using the CAMARADES tools. Baicalin significantly increased sucrose preference test (SPT) [SMD= 21.31, 95%CI (16.32, 26.31), P < 0.00001]. mThe tail suspension test (TST) duration significantly decreased in the baicalin group compared to the model group [SMD = -39.3, 95%CI (-49.71, -28.89), P < 0.0001]. Furthermore, baicalin reduced immobility time in rats subjected to the forced swim test (FST) [SMD = -39.73, 95%CI (-48.77, -30.69) P < 0.0001]. Compared to the model group, baicalin treatment also significantly increased the frequency of crossings in the open field test (OFT) [SMD = 32.44, 95%CI (17.74, 47.13), P < 0.00001]. Baicalin significantly improves the manifestations of depressive symptoms. The effect of baicalin against depression is exerted through its anti-inflammatory actions, inhibition of oxidative stress, regulation of the HPA axis, and restoration of neuroplasticity. Future studies will be needed to further explore how these promising preclinical findings can be translated into clinical treatment for depression. https://www.crd.york.ac.uk/PROSPERO/, identifier CRD42023472181.

MATB for assessing different mental workload levels.

Multi-Attribute Task Battery (MATB) is a computerized flight simulator for aviation-related tasks, suitable for non-pilots and available in many versions, including open source. MATB requires the individual or simultaneous execution of 4 sub-tasks: system monitoring (SYSMON), tracking (TRACK), communications (COMM), and resource management (RESMAN). Fully customizable, the design of test duration, number of sub-tasks used, event rates, response times and overlap, create different levels of mental load. MATB can be combined with an additional auditory attention (Oddball) task, or with physiological constraints (i.e., sleep loss, exercise, hypoxia). We aimed to assess the main characteristics of MATB design for assessing the response to different workload levels. We identified and reviewed 19 articles for which the effects of low and high workload were analyzed. Although MATB has shown promise in detecting performance degradation due to increase workload, studies have yielded conflicting or unclear results regarding MATB configurations. Increased event rates, number of sub-tasks (multitasking), and overlap are associated with increased perceived workload score (ex. NASA-TLX), decreased performance (especially tracking), and neurophysiological responses, while no effect of time-on-task is observed. The median duration used for the test is 20min (range 12-60) with a level duration of 10min (range 4-15). To assess mental workload, the median number of stimuli is respectively 3 events/min (range 0.6-17.2) for low, and 23.5 events/min (range 9-65) for high workload level. In this review, we give some recommendations for standardization of MATB design, configuration, description and training, in order to improve reproducibility and comparison between studies, a challenge for the future researches, as human-machine interaction and digital influx increase for pilots. We also open the discussion on the possible use of MATB in the context of aeronautical/operational constraints in order to assess the effects combined with changes in mental workload levels. Thus, with appropriate levels of difficulty, MATB can be used as a suitable simulation tool to study the effects of changes on the mental workload of aircraft pilots, during different operational and physiological constraints.

Exploring and field-demonstrating geofence-based occupancy-centric control in residential buildings

Several studies have highlighted the thermal comfort challenges associated with occupancy-centric control (OCC) when occupants first arrive, despite OCC demonstrating energy savings potential in buildings. To address this challenge, a geofence-based OCC (Geo-OCC), where the virtual boundary of the occupant’s physical location is infused into the smart thermostat, is explored to pre-condition buildings, aiming to alleviate thermal discomfort. This research adopted an apples-to-apples field testing approach to quantify how Geo-OCC impacts the thermal comfort and energy consumption of the heating, ventilation, and air-conditioning (HVAC) system in two 1,200 ft2 lab homes located in Texas, USA. These two homes were designed and built as identically as they could be. Two side-by-side experimental scenarios were designed to compare different control strategies through integrations with smart thermostats. In scenario 1, Geo-OCC was implemented in the east home, while a baseline case without OCC (Non-OCC) was executed in the west home. In scenario 2, Geo-OCC was employed in the east home, and a traditional OCC based on occupancy presence sensors (Sensed-OCC) was implemented in the west home, demonstrating Geo-OCC’s ability to alleviate thermal discomfort. The field-testing results of scenario 1 suggested that Geo-OCC achieved a 46.41 % reduction in heating energy consumption compared to Non-OCC over the testing duration of 25 days, resulting in a maximum unmet degree (UD) of 3.83 °C in a 5-minute sampling frequency, in contrast to a maximum UD of 0.83 °C in Non-OCC mode. The results from the field testing in scenario 2 indicated that Geo-OCC reduced the maximum UD to 1.94 °C in a 5-minute sampling frequency, compared to 2.28 °C in Sensed-OCC, without an increase in heating energy consumption. The results of the scenario 1 experiment suggested the OCC decreased the HVAC energy consumption while having a slightly adverse effect on thermal comfort during occupied periods, especially upon the first arrival of occupants. The field testing of scenario 2 exhibited the capability of Geo-OCC to enhance thermal comfort with minor effects on the HVAC energy consumption. In addition, Geo-OCC displayed the potential to reduce the peak demand increase caused by traditional Sensed-OCC.

Reference Database for a Novel Binocular Visual Function Perimeter: A Randomized Clinical Trial

PurposeTo construct a comprehensive reference database for a novel binocular automated perimeter. DesignA four-site prospective randomized clinical trial. Subjects and controls356 healthy subjects without ocular conditions that might affect visual function were categorized into 7 age groups. MethodsSubjects underwent comprehensive ocular examination of both eyes before enrollment. Using the TEMPO/IMOvifa automated perimeter (Topcon Healthcare/CREWT Medical Systems, Tokyo, Japan), each subject completed four binocular threshold visual field (VF) tests during a single visit: First, practice 24-2 and 10-2 tests were obtained from both eyes. Next, study 24-2 and 10-2 tests were obtained from both eyes. Test order of each sequence was randomized, and the tests were conducted under Standard Automated Perimetry testing conditions (SAP): Goldmann stimulus size III, 3183 cd/m2 maximum stimulus intensity, and background intensity of 10 cd/m2, using AIZE-Rapid test strategy. Standard VF reliability indices were assessed. For each subject, 24-2 and 10-2 test results from one randomly selected eye were analyzed. Main Outcome MeasuresPerimetric threshold sensitivity and reference limits for each test analysis parameter. ResultsThe ages of the study cohort were widely distributed, with a mean age (SD) of 52.3 (18.5) years. Sex assignment was 44.0% male and 56.0% female. The majority of subjects self-identified as White (67.4%), followed by Black or African American (13.5%) and Asian (8.7%), with 14.6% self-identified as Hispanic or Latino ethnicity. Mean sensitivity (MS) (SD) was 29.1 (1.3) decibels (dB) for the 24-2 and 32.4 (1.0) dB for the 10-2 test. For the 24-2 and 10-2, MS (SD) age-related changes averaged -0.06 (0.01) dB and -0.05 (0.01) dB per year, respectively. The normal range of pointwise threshold sensitivity increased with eccentricity and showed asymmetry around the mean, particularly notable in the 24-2 test. Mean (SD) binocular test duration was 3.18 (0.38) minutes (1 minute 35 seconds per eye) for the 24-2 test and 3.58 (0.43) minutes (1minute 47 seconds per eye) for the 10-2 test. ConclusionsA reference database for the TEMPO/IMOvifa perimeter was established, highlighting the significance of considering both age and stimulus eccentricity in interpreting threshold visual field test results.

Experimental and numerical study of a novel composite building wall U-value

The present study aims to minimize the overall heat transfer coefficient (U-value) and heat flux through building walls to improve indoor thermal comfort, using different bricks and insulating materials in building wall construction. The building walls of three different types of bricks (Type-1, Type-2, and Type-3) were tested to compare the U-value through the wall. The brick with the low U-value was used to build a composite wall with the addition of glass wool and air cavity. The experiment was conducted maintaining different hot chamber temperatures (40℃ to 65℃) to see the effect of hot chamber temperature on the U-value. The temperature of the cold fluid chamber is increased by 0.9℃ in 0 to 210 min of testing duration. The maximum heat flux using Type-3 brick in the composite wall is reduced by 3.37%, and the percentage reduction in indoor temperature is 40.83%. Steady-state numerical analysis was also performed to perceive the temperature distribution on the composite wall surface and found to be well-matched with the experimental model with a percentage deviation of 1.96%. The results suggested that using glass wool and air cavities with low thermal conductivity, low density, and high specific heat capacity effectively reduces the U-value throughout the building wall.

Исследование эффективности теста ATTON в диагностике нарушения внимания у детей 5—7 лет

&lt;p&gt;This article describes the study of attention concentration in children using a new method &amp;mdash; the ATTON test for the first time. The duration of the test, the response rate, the number of errors and correct answers in the main (106 children) and control (108 children) groups were measured. The authors identified differences in the groups in test duration, response rate, number of errors and correctly completed tasks at the significance level &amp;alpha;&amp;lt;0.001. And also presented normative indicators of test duration, response rate, number of erroneous and correct answers for children aged 5, 6 and 7 years. The relationship between the duration of the test, the number of errors and correct answers of the ATTON test with the scores of the proof-reading test "Encryption", as well as with a non-verbal intellectual indicator, was revealed. The retest reliability was determined at the level of r=0.757 at p&amp;lt;0.001. The Cronbach's alpha value for the test was 0.973.&lt;/p&gt;