Dual-bridge Resonant Converter Research Articles

Analysis and Verification of a Half-Dual Bridge Resonant Converter with Voltage Match Modulation

To overcome the weakness of the narrow conversion gain of dual bridge resonant converter, a half-dual bridge resonant converter (H-DBRC) with voltage match modulation (VMM) is proposed and implemented for wide voltage range applications. The H-DBRC, including a full bridge on the primary side and a half bridge on the secondary side, is adopted to realize the bidirectional power flow and wide voltage operation. Owing to the synergy between the H-DBRC structure and VMM strategy, the converter can operate in full-bridge state and half-bridge state with maximized ZVS (zero-voltage switching) operation and minimized circulating current. The steady-state analysis is performed and the solutions for both forward and backward modes could be obtained uniformly by using the fundamental harmonics approximation approach. The soft-switching characteristics, implementation process and design example are analyzed in detail. Finally, to confirm the theoretical analysis and feasibility, both simulation and experimental verifications are demonstrated in this paper. Since the converter consistently achieves voltage-matching operation, the optimal ZVS range can be obtained when the voltage gain M is between 0.5 to 1. Moreover, the economic cost and control complexity are greatly reduced because only six switches are required in the converter.

Operation of a semi dual-bridge resonant converter with a tunable resonant tank

In this paper, a control strategy to minimize the root-mean-square (rms) current and eliminate the backflow power over a wide operation range is proposed to enhance the conversion efficiency of a semi dual-bridge resonant converter (SDBRC). Steady-state analysis of the converter is performed using the fundamental harmonic approximation approach. Optimal operating states are then found with the minimum resonant current and zero backflow power for both buck and boost operation. The switching conditions of the optimal operating trajectory are also elaborated in detail. The converter is enabled to work under the optimal operating condition in a wide load range by adjusting the switch-controlled capacitor based tunable resonant tank continuously. Finally, a prototype converter rated at 500 W is built and extensive experimental tests have been done to evaluate the proposed switch-controlled capacitor based topology converter and its optimal modulation. Performance improvement brought up by the proposed converter with its modulation could be confirmed by means of comparisons with previous works.

Constant-Current, Constant-Voltage Operation of a Dual-Bridge Resonant Converter: Modulation, Design and Experimental Results

To meet the requirements of charging the mainstream rechargeable batteries, in this work, a dual-bridge resonant converter (DBRC) is operated as a battery charger. Thanks to the features of this topology, the required high efficiency can be achieved with a wide range of battery voltage and current by using different modulation variables. Firstly, a typical charging process including constant-voltage stage and constant-current stage is indicated. Then, two different modulation methods of the DBRC are proposed, both of which can realize constant-voltage charging and constant-current charging. Method I adopts phase-shift modulation with constant switching frequency while Method II adopts varying frequency modulation. Furthermore, as guidance for practical application, the design principles and detailed design procedures of the DBRC are customized for the two modulation methods respectively in order to reduce the switching loss and conduction loss. Consequently, the full soft-switching operation with low rms tank current is achieved under the two modulation methods, which contributes to the high efficiency of the whole charging process. At last extensive simulation and experimental tests on a lab prototype converter are performed, which prove the feasibility and effectiveness of the proposed modulation strategies.

A Dual-Bridge DC–DC Resonant Converter Using Extended PWM and Phase-Shift Control

To enhance the overall efficiency of a dual-bridge resonant converter, a new asymmetric pulsewidth modulation (PWM) control named extended pulsewidth modulation (EPWM) with both variable pulsewidth and variable symmetry is introduced in this article, which is applied to the high-voltage-side bridge of the converter and is combined with phase-shift control to form a 3-D gating scheme. A specified control strategy based on the 3-D gating scheme is then derived for the purpose of minimum tank current operation. Thanks to the flexibility brought by EPWM, full zero-voltage switching (ZVS) operation range is maintained as large as that of a conventional PWM-based minimum current trajectory, and only one switch loses ZVS at light load. The modulated voltage pulsewidth is kept at high level in a wide load range, which compromises the by-effect of high-order harmonics due to asymmetric modulation. Besides, the backflow power on both sides is almost minimized naturally. Therefore, the proposed control trajectory can have better performance in a light-load region than previous reported solutions. Experimental results prove the accuracy and effectiveness of the proposed minimum current operation with wide ZVS range and show the improvement of overall conversion efficiency.

Smart Internet of Things (IOT) System for Performance Improvement of Dual Bridge LLC Resonant Converter by Using Sophisticated Distribution Control Method (SDC)

A resonant converter is a kind of electric power converter that contains a system of inductors and capacitors called a resonant tank, tuned to resonate at a particular frequency in this work recommends a better-quality dual bridge LLC resonant converter with a novel controller technique. The resonant converters include the serial or parallel connections of inductors and capacitors to activate the switch to realize the Zero Current Switching (ZCS) and Zero Volt Switching (ZVS) under resonance conditions. The resonant effects are switching sufferers, turning strain and electromagnetic interference problems the switching resonant converter controls the output voltage through changing frequency and generally can be sub classified in ZCS converter and ZVS converter. This scheme had combined wireless monitoring for dual bridge LLC resonant converter for dc distribution applications based on sophisticated distribution controller (SDC) through the internet of things and embedded structure access and other mechanisms. The consequence of our exhibition demonstrates that the framework can monitor and store the manipulate data from the converter. Thus, the wireless monitoring functions are realized in real-time. This converter permits both forward and reverses power exchange between the source and the load, to keep up the output voltage consistent, regardless of load and line unsettling influences, it is important to work the converter as a closed loop system. The proposed SDC based dual bridge resonant converter has validated through simulation in Matlab Simulink environment. A hardware setup is also developed to validate the simulation. General 97% effectiveness accomplished at full load condition in light of the dual bridge resonant converter.

The FHA Analysis of Dual-Bridge LLC Type Resonant Converter

The dual bridge resonant converter is designed in this paper. In this converter the LLC type resonance configuration is proposed .This types is compared with the other configurations and its benefits are narrated in this paper. The steady-state analysis of the LLC configuration is done using fundamental harmonics approximation method and the values for the components of resonance configuration is found and used for simulation. The simulation results shows that the converter is able to achieve the zero voltage switching for the wide load range and attains a good efficiency. DOI: http://dx.doi.org/10.11591/ijpeds.v4i4.6513