Disulfide Nanosheets Research Articles

4-Ethylphenyl Sulfate Detection by an Electrochemical Sensor Based on a MoS2 Nanosheet-Modified Molecularly Imprinted Biopolymer.

One of the gut-derived uremic toxins 4-ethylphenyl sulfate (4-EPS) exhibits significantly elevated plasma levels in chronic kidney diseases and autism, and its early quantification in bodily fluids is important. Therefore, the development of rapid and sensitive technologies for 4-EPS detection is of significant importance for clinical diagnosis. In the current work, the synthesis of a molecularly imprinted biopolymer (MIBP) carrying 4-EPS specific cavities only using the biopolymer polydopamine (PDA) and molybdenum disulfide (MoS2) nanosheets has been reported. The fabricated electrode was prepared using screen-printed carbon electrodes on a polyvinyl chloride substrate. The synthesized material was characterized using several techniques, and electrochemical studies were performed using cyclic voltammetry (CV) and differential pulse voltammetry (DPV) techniques. The DPV technique for the electrochemical sensing of 4-EPS using the fabricated sensor (PDA@MoS2-MIBP) determined a sensitivity of 0.012 μA/ng mL/cm2 and a limit of detection of 30 ng/mL in a broad linear range of 1-2200 ng/mL. Also, the interferent study was performed to evaluate the selectivity of the fabricated sensor along with the control and stability study. Moreover, the performance of the sensor was evaluated in the spiked urine sample, and a comparison was made with the data obtained by ultraperformance liquid chromatography-tandem mass spectroscopy.

Boron carbide decorated tungsten disulfide nanosheet composite for determination of chloramphenicol in food and pharmaceutical samples

Making the nanocomposites of metal oxides or metal sulfides with carbon source materials has a huge impact on the electrochemical determination of toxic chemicals. To determine the adverse side effects of the antibiotics, electrochemical sensors have been used as they can peek into the sensitivity of the drug sample. This work has done the sensitive amperometric evaluation of a chloramphenicol antibiotic by modifying the electrode of tungsten disulfide decorated boron carbide. Here, tungsten disulfide (WS2) nanosheets and boron carbide (B4C) materials were synthesized by conventional methods which give a good amount of yield. The composite was prepared by the green and cost-effective sonochemical approach with good morphology. The conductivity of the nanocomposite and the response to chloramphenicol were determined by cyclic voltammetry. The sensitivity, limit of detection (LOD), and the linear range were observed by the highly sensitive amperometric technique. From the amperometric analysis, the prepared nanocomposite shows nominal LOD as a 17.4 nM, a broad linear range (0.025–1134.6 µM), and good sensitivity of 1.52 µA µM−1 cm−2. Practicability of the modified sensor was studied in food and pharmaceutical samples with adequate recovery performances. Moreover, the modified electrode shows good stability, repeatability, reproducibility, and anti-interfering properties against the array of food and biological interferences.

Heterogeneous interfaces in 3D interconnected networks of flower-like 1T/2H Molybdenum disulfide nanosheets and carbon-fibers boosts superior EM wave absorption

With the wide application of electromagnetic waves in national defense, communication, navigation and home appliances, the electromagnetic pollution problem is becoming more and more prominent. Therefore, high-performance, and low-density composite wave-absorbing materials have attracted much attention. In this paper, three-dimensional (3D) network structures of flower-like 1T/2H Molybdenum disulfide nanosheets anchored to carbon fibers (1T/2H MoS2/CNFs) were prepared by electrostatic spinning technique and calcination process. The morphology and electromagnetic wave absorption properties were tuned by changing the content of flower-like MoS2. The optimized 1T/2H MoS2/CNFs composite exhibits superior electromagnetic wave absorption with minimum reflection (RLmin) of −42.26 dB and effective absorption bandwidth (EAB) of 6.48 GHz at 2.5 mm. Multi-facts contribute to the super performance. First, the uniquely designed nanosheet and 3D interconnected networks leads to multiple reflection and scattering of electromagnetic waves, which promotes the attenuation of electromagnetic waves. Second, the propriate content of CNFs and MoS2 with different phase regulates its impedance matching characteristic. Third, Numerous heterogeneous interfaces existed between CNFs and MoS2, 1T and 2H MoS2 phase results in interface polarization. Besides, the 1T/2H MoS2 rich in defects induces defect polarization, improving the dielectric loss. Furthermore, the electromagnetic wave absorption performance was proved via radar reflectance cross section simulation. This work illustrates 1T/2H MoS2/CNFs is a promising material for electromagnetic absorption with wide bandwidth, strong absorption, low density, and high thermal stability.

Ratio design of bimetallic Pd‐Rh nanoparticles on MoS2 nanosheets: Excellent electrocatalysts for hydrogen evolution reaction

The decrease in noble metal content presents an efficient approach to attain commercial, effective, and durable electrocatalysts for the hydrogen evolution reaction (HER) at a low fabrication cost. Nonetheless, achieving a proper balance between bimetallic loading ratios and HER performance remains challenging. In this study, a simple and environmentally friendly sonochemical method is employed to successfully synthesize bimetallic palladium–rhodium nanoparticles (Pd‐Rh) with varying ratios, confined within molybdenum disulfide (MoS2) nanosheets. Bimetallic Pd‐Rh/MoS2 composite with different ratios of Pd:Rh is synthesized by adjusting the feed ratio of Pd and Rh precursors (1:4, 1:1, and 4:1). The HER electrocatalytic activity of the bimetallic Pd1‐Rh1/MoS2 composite exhibits the lowest overpotential and a superior Tafel slope, closely rivaling the electrocatalytic activity of the commercial 20 wt% Pt/C. Furthermore, the bimetallic Pd1‐Rh1/MoS2 composite exhibits remarkable stability and durability, with almost negligible performance decay after 2000 cycles. These outstanding HER electrocatalytic properties of the bimetallic composite result from a higher number of active sites, a significantly larger electrochemically active surface area, reduced charge‐transfer resistance, and a larger double‐layer capacitance. These factors collectively facilitate faster adsorption and desorption of hydron on the surface of electrocatalyst.

Size and Shape Selective Classification of Nanoparticles

As nanoparticle syntheses on a large scale usually yield products with broad size and shape distributions, the properties of nanoparticle-based products need to be tuned after synthesis by narrowing the size and shape distributions or via the removal of undesired fractions. The development of property-selective classification processes requires a universal framework for the quantitative evaluation of multi-dimensional particle fractionation processes. This framework must be applicable to any property and any particle classification process. We extended the well-known one-dimensional methodology commonly used for describing particle size distributions and fractionation processes to the multi-dimensional case to account for the higher complexity of the property distribution and separation functions. In particular, multi-dimensional lognormal distributions are introduced and applied to diameter and length distributions of gold nanorods. The fractionation of nanorods via centrifugation and by orthogonal centrifugal and electric forces is modeled. Moreover, we demonstrate that analytical ultracentrifugation with a multi-wavelength detector (MWL-AUC) is a fast and very accurate method for the measurement of two-dimensional particle size distributions in suspension. The MWL-AUC method is widely applicable to any class of nanoparticles with size-, shape- or composition-dependent optical properties. In addition, we obtained distributions of the lateral diameter and the number of layers of molybdenum disulfide nanosheets via stepwise centrifugation and spectroscopic evaluation of the size fractions.

Ultrathin TiS2@N,S-Doped Carbon Hybrid Nanosheets as Highly Efficient Photoresponsive Antibacterial Agents.

Nanobactericides are employed as a promising class of nanomaterials for eradicating microbial infections, considering the rapid resistance risks of conventional antibiotics. Herein, we present a pioneering approach, reporting the synthesis of two-dimensional titanium disulfide nanosheets coated by nitrogen/sulfur-codoped carbon nanosheets (2D-TiS2@NSCLAA hybrid NSs) using a rapid l-ascorbic acid-assisted sulfurization of Ti3C2Tx-MXene to achieve efficient alternative bactericides. The as-developed materials were systematically characterized using a suite of different spectroscopy and microscopy techniques, in which the X-ray diffraction/Raman spectroscopy/X-ray photoelectron spectroscopy data confirm the existence of TiS2 and C, while the morphological investigation reveals single- to few-layered TiS2 NSs confined by N,S-doped C, suggesting the successful synthesis of the ultrathin hybrid NSs. From in vitro evaluation, the resultant product demonstrates impressive bactericidal potential against both Gram-positive Staphylococcus aureus and Gram-negative Escherichia coli bacteria, achieving a substantial decrease in the bacterial viability under a 1.2 J dose of visible-light irradiation at the lowest concentration of 5 μg·mL-1 compared to Ti3C2Tx (15 μg·mL-1), TiS2-C (10 μg·mL-1), and standard antibiotic ciprofloxacin (15 μg·mL-1), respectively. The enhanced degradation efficiency is attributed to the ultrathin TiS2 NSs encapsulated within heteroatom N,S-doped C, facilitating effective photogenerated charge-carrier separation that generates multiple reactive oxygen species (ROS) and induced physical stress as well as piercing action due to its ultrathin structure, resulting in multimechanistic cytotoxicity and damage to bacterial cells. Furthermore, the obtained results from molecular docking studies conducted via computational simulation (in silico) of the as-synthesized materials against selected proteins (β-lactamasE.coli/DNA-GyrasE.coli) are well-consistent with the in vitro antibacterial results, providing strong and consistent validation. Thus, this sophisticated study presents a simple and effective synthesis technique for the structural engineering of metal sulfide-based hybrids as functionalized synthetic bactericides.

Layer-by-layer Assembly of Nanosheets with Matching Size and Shape for More Stable Membrane Structure than Nanosheet-Polymer Assembly.

Layer-by-layer (LbL) assembly of oppositely charged materials has been widely used as an approach to make two-dimensional (2D) nanosheet-based membranes, which often involves 2D nanosheets being alternately deposited with polymer-based polyelectrolytes to obtain an electrostabilized nanosheet-polymer structure. In this study, we hypothesized that using 2D nanosheets with matching physical properties as both polyanions and polycations may result in a more ordered nanostructure with better stability than a nanosheet-polymer structure. To compare the differences between nanosheet-nanosheet vs nanosheet-polymer structures, we assembled negatively charged molybdenum disulfide nanosheets (MoS2) with either positively charged graphene oxide (PrGO) nanosheets or positively charged polymer (PDDA). Using combined measurements by ellipsometer and quartz crystal microbalance with dissipation, we discovered that the swelling of MoS2-PrGO in ionic solutions was 60% lower than that of MoS2-PDDA membranes. Meanwhile, the MoS2-PrGO membrane retained its permeability upon drying, whereas the permeability of MoS2-PDDA decreased by 40% due to the restacking of MoS2. Overall, the MoS2-PrGO membrane demonstrated a better filtration performance. Additionally, our X-ray photoelectron spectroscopy results and analysis on layer density revealed a clearer transition in material composition during the LbL synthesis of MoS2-PrGO membranes, and the X-ray diffraction pattern suggested its resemblance to an ordered, layer-stacked structure. In conclusion, the MoS2-PrGO membrane made with nanosheets with matching size, shape, and charge density exhibited a much more aligned stacking structure, resulting in reduced membrane swelling under high salinity solutions, controlled restacking, and improved separation performance.

Surface modified molybdenum disulfide nanosheets for corrosion resistance improvement on polyurethane coatings

Abstract Organic–inorganic hybrid coating has been applied on metallic corrosion protection effectively. Molybdenum disulfide (MoS2) nanosheets with graphene-like two-dimensional lamellar structure were an anticorrosion inorganic additive, rendering the organic coating better corrosion resistant. However, the aggregation and poor solubility are still current issues that should be addressed. Functionalization MoS2 nanosheets with surface modified by polydopamine (PDA) and silane coupling agent (KH560) were prepared in polyurethane (PU) composite coatings to obtain dense and intact multilayer network structure coatings for corrosion protection. KH560-PDA-MoS2/PU coating with crosslinked polymer network structure has a high impedance modulus, large contact angle, and strong hydrophobicity. The coating meets the national technical standards for salt spray testing and nitric acid (HNO3) titration testing, demonstrating excellent corrosion resistance.

Vanadium disulfide nanosheets based membrane for filter application

BackgroundSurface and groundwater resources are being significantly contaminated by organic pollutants, particularly diverse organic dyes released by the textile industry, thereby posing a considerable threat to aquatic ecosystems. Methodswe describe the development of a vanadium disulfide (VS2) membrane using a simple vacuum-assisted filtration method. Significant findingsIt demonstrated impressive rejection rates for 10 ppm methylene blue (MB) solutions (92.5 %, 95.3 %, and 96.8 %) and 10 ppm methylene violet (MV) solutions (96.1 %, 97.3 %, and 98.1 %). These notable outcomes are credited to the pivotal role of the layered structure of the VS2 membrane, with thicknesses of ∼44 μm, 56 μm, and 68 μm, respectively. The water flux of these membranes exhibited a range of ∼1300, 1350, and 1400 L m−2 h−1 for the MB solution. For the MV solution, the water flux ranged around ∼1100, 1150, and 1200 L m−2 h−1. Further, it highlights the efficient filtration performance of these membranes for both MB and MV solutions. The membrane's highly efficient separation performance not only holds promise for various filtration applications but also establishes it as an innovative and effective solution in the continuous global endeavors to address water pollution.

Tribological performances of MoS2/C60 nanocomposite as lubricating additive in dioctyl sebacate

PurposeThis paper aims to solve the problems molybdenum disulfide (MoS2) nanosheets suffer from inadequate dispersion stability and form a weak lubricating film on the friction surface, which severely limits their application as lubricant additives.Design/methodology/approachMoS2/C60 nanocomposites were prepared by synthesizing molybdenum disulfide (MoS2) nanosheets on the surface of hydrochloric acid-activated fullerenes (C60) by in situ hydrothermal method. The composition, structure and morphology of MoS2/C60 nanocomposites were characterized. Through the high-frequency reciprocating tribology test, its potential as a lubricant additive was evaluated.FindingsMoS2/C60 nanocomposites that were prepared showed good dispersion in dioctyl sebacate (DOS). When 0.5 Wt.% MoS2/C60 was added, the friction reduction performance and wear resistance improved by 54.5% and 62.7%, respectively.Originality/valueMoS2/C60 composite nanoparticles were prepared by in-situ formation of MoS2 nanosheets on the surface of C60 activated by HCl through hydrothermal method and were used as potential lubricating oil additives.Peer reviewThe peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-10-2023-0321/

Core-Shell CoS2@MoS2 with Hollow Heterostructure as an Efficient Electrocatalyst for Boosting Oxygen Evolution Reaction.

It is imperative to develop an efficient catalyst to reduce the energy barrier of electrochemical water decomposition. In this study, a well-designed electrocatalyst featuring a core-shell structure was synthesized with cobalt sulfides as the core and molybdenum disulfide nanosheets as the shell. The core-shell structure can prevent the agglomeration of MoS2, expose more active sites, and facilitate electrolyte ion diffusion. A CoS2/MoS2 heterostructure is formed between CoS2 and MoS2 through the chemical interaction, and the surface chemistry is adjusted. Due to the morphological merits and the formation of the CoS2/MoS2 heterostructure, CoS2@MoS2 exhibits excellent electrocatalytic performance during the oxygen evolution reaction (OER) process in an alkaline electrolyte. To reach the current density of 10 mA cm-2, only 254 mV of overpotential is required for CoS2@MoS2, which is smaller than that of pristine CoS2 and MoS2. Meanwhile, the small Tafel slope (86.9 mV dec-1) and low charge transfer resistance (47 Ω) imply the fast dynamic mechanism of CoS2@MoS2. As further confirmed by cyclic voltammetry curves for 1000 cycles and the CA test for 10 h, CoS2@MoS2 shows exceptional catalytic stability. This work gives a guideline for constructing the core-shell heterostructure as an efficient catalyst for oxygen evolution reaction.

Robust pseudocapacitive Na+ intercalation induced by MoS2 on active Mo2C current collector interface for high areal capacity sodium-ion batteries

Sodium-ion batteries (SIBs) have emerged as compelling alternatives in the realm of electrochemical energy devices, poised to substitute lithium-ion batteries (LIBs). The primary challenge encompasses not only the scarcity of anode materials exhibiting exceptional Na+ storage capacity but also the endeavor to achieve high areal capacity. To address this challenge, a comprehensive strategy is proposed that entails utilizing a highly conductive molybdenum dicarbide (Mo2C) current collector (denoted as CCM) as a supporting scaffold for the bottom-up growth of molybdenum disulfide nanosheets (MoS2, serving as the main active component) (denoted as CCM@MoS2). The CCM improves interfacial bonding with MoS2 nanosheets and offers additional capacity to accommodate the increased Na+ insertion activity. Both theoretical and kinetic analyses reveal that the enhanced Na+ storage properties primarily stem from favorable adsorption energy, reduced diffusion barrier, and intercalation pseudocapacitance due to the strong electronic interfacial interaction between active CCM and MoS2. Hence, the as-prepared optimized CCM@MoS2 electrode exhibits a superior areal capacity of 6.36 mAh cm−2 at 0.4 mA cm−2, excellent rate capability of 1.02 mAh cm−2 at 24 mA cm−2 and long cycle life up to 500 cycles at 4 mA cm−2. Interesting, our as-prepared CCM@MoS2 electrode shows better performance for Na+ storage than Li+ storage at higher current density, affirming the enhanced kinetics in our architecture. This work proposes a rational strategy to enhance the areal capacity and stability of MoS2-based anode for SIBs and beyond.

The production of electrodes for microsupercapacitors based on MoS2-modified reduced graphene aerogels by 3D printing

Micro-supercapacitors (MSCs) are of interest because of their high power density and excellent cycling performance, offering a broad array of potential applications. However, preparing electrodes for the MSCs with an extremely high areal capacitance and energy density remains a challenge. We constructed MSC electrodes with an ultra-high area capacitance and a high energy density, using reduced graphene oxide aerogel (GA) and MoS2 as the active materials, combined with 3D printing and surface modification. Using 3D printing, we obtained electrodes with a stable macrostructure and a GA-crosslinked micropore structure. We also used a solution method to load the surface of the printed electrode with molybdenum disulfide nanosheets, further improving the electrochemical performance. The surface capacitance of the electrode reached 3.99 F cm−2, the power density was 194 W cm−2, and the energy density was 1 997 mWh cm−2, confirming its excellent electrochemical performance and cycling stability. This work provides a simple and efficient method for preparing MSC electrodes with a high areal capacitance and energy density, making them ideal for portable electronic devices.

Interactions of monolayer molybdenum disulfide sheets with metalloid antimony in aquatic environment: Adsorption, transformation, and joint toxicity

The tremendous application potentiality of transitional metal dichalcogenides (TMDs), such as molybdenum disulfide (MoS2) nanosheets, will unavoidably lead to increasing release into the environment, which could influence the fate and toxicity of co-existed contaminants. The present study discovered that 59.8 % of trivalent antimony [Sb(III)] was transformed by MoS2 to pentavalent Sb [Sb(V)] in aqueous solutions under light illumination, which was due to hole oxidation on the nanosheet surfaces. A synergistic toxicity between MoS2 and Sb(III, V) to algae (Chlorella vulgaris) was observed, as demonstrated by the lower median-effect concentrations of MoS2 + Sb(III)/Sb(V) (13.1 and 20.9 mg/L, respectively) than Sb(III)/Sb(V) (38.8 and 92.5 mg/L, respectively) alone. Particularly, MoS2 at noncytotoxic doses notably increased the bioaccumulation of Sb(III, V) in algae, causing aggravated oxidative damage, photosynthetic inhibition, and structural alterations. Metabolomics indicated that oxidative stress and membrane permeabilization were primarily associated with down-regulated amino acids involved in glutathione biosynthesis and unsaturated fatty acids. MoS2 co-exposure remarkably decreased the levels of thiol antidotes (glutathione and phytochelatins) and aggravated the inhibition on energy metabolism and ATP synthesis, compromising the Sb(III, V) detoxification and efflux. Additionally, extracellular P was captured by the nanosheets, also contributing to the uptake of Sb(V). Our findings emphasized the nonignorability of TMDs even at environmental levels in affecting the ecological hazard of metalloids, providing insight into comprehensive safety assessment of TMDs.

NIR-triggered drug delivery system based on tungsten disulfide nanosheets coated pH/temperature responsive polymer for controlled delivery of palbociclib: Release kinetics models

BackgroundPolymers that respond to changes in ambient conditions, such as physiological pH and temperature, have garnered increasing interest in the realm of drug delivery systems. In this study, a novel pH and temperature dual-responsive carrier was prepared for palbociclib delivery. MethodsThe tungsten disulfide nanosheets were functionalized with allyl glycidyl ether, allyl alcohol, and N-vinylcaprolactam, and then grafted with 2, 3-diaminopyridine. The in-vitro drug release was studied in simulated cancer (pH=5.6) and blood (pH=7.4) fluids at different temperatures. Significant FindingsThe in-vitro drug release test showed better release behavior at high temperatures in simulated cancer fluid compared to lower temperatures in simulated blood fluid, releasing about 87.53% of the entrapped drug within 6 h at 45 °C in simulated cancer fluid. The drug release shown the best fitting with the Korsmeyer-Peppas kinetic model. When the near-infrared laser irradiation was applied for 15 min, the drug release from the nanocarrier was three times higher than that without the laser irradiation. The maximum sorption capacity of the drug was achieved at approximately 79.04 mg g−1 at pH=8 for 45 min at 25 °C. The sorption procedure was found to follow the Langmuir isotherm and a pseudo-2nd-order kinetic model quite well.

Design and Development of Dual Responsive Nanocarrier Based on Tungsten Disulfide Nanosheets and Its Cytotoxic Effect on PC-3 Cells as an Efficient In Vitro Drug Delivery System for Flutamide

Design and Development of Dual Responsive Nanocarrier Based on Tungsten Disulfide Nanosheets and Its Cytotoxic Effect on PC-3 Cells as an Efficient In Vitro Drug Delivery System for Flutamide

Electrodeposition of PdPt Nanoparticles on Edges and S-Vacancies in Exfoliated MoS2 Nanosheets for Enhanced Hydrogen Evolution Activity.

Deposition of metal nanoparticles onto the molybdenum disulfide (MoS2) nanosheets is an efficient method to tune the electronic structure of the MoS2 and maximize its catalytic performance towards the hydrogen evolution reaction (HER). Herein, we report the electrodeposition of Pd and Pt nanoparticles onto desulfurized MoS2 nanosheets (MoS2-x) to achieve an improved HER activity in an acidic electrolyte. The initial MoS2 powder was exfoliated and isolated through centrifugation, followed by electrochemical desulfurization to create defect sites. Subsequently, Pt and Pd nanoparticles were electrodeposited onto the S-vacancies of MoS2-x nanosheets. The resulting PdPt nanoparticles, with a diameter of 3.3 ±1.7 nm, were distributed across the surfaces of the nanosheets. A preferential deposition was evident at the edges of the nanosheets, particularly when Pd was deposited first followed by Pt. Owing to this preferential deposition of Pd and Pt and the synergistic interaction of MoS2-x with Pd and Pt, the prepared catalyst exhibited a low overpotential of 30 mV at 10 mA cm-2, which is 2.7× lower than the MoS2-x alone. The prepared catalyst exhibited a 1.7× increase in the mass activity at 20 mV overpotential, relative to that of a commercial Pt/C nanocatalyst, showcasing its promising potential as an alternative catalyst.

Chemisorption-Induced Robust and Homogeneous Tungsten Disulfide Interlayer Enables Stable PEDOT-Free Organic Solar Cells with Over 19% Efficiency.

Construction of a high-quality charge transport layer (CTL) with intimate contact with the substrate via tailored interface engineering is crucial to increase the overall charge transfer kinetics and stability for a bulk-heterojunction (BHJ) organic solar cell (OSC). Here, we demonstrate a surface chemistry strategy to achieve a homogeneous composite hole transport layer (C-HTL) with robust substrate contact by self-assembling two-dimensional tungsten disulfide (WS2) nanosheets on a thin molybdenum oxide (MoO3) film-evaporated indium tin oxide (ITO) substrate. It is found that over such a well-defined C-HTL, WS2 is homogeneously tethered on the ITO/MoO3 substrate stemming from the strong electronic coupling interaction between the building blocks, which enables a favorable interfacial configuration in terms of uniformity. As a result, the D18:L8-BO-based OSC with C-HTL exhibits a power conversion efficiency (PCE) of 19.23%, an 11% improvement over the WS2-based control device, and the highest efficiency among single-junction PEDOT-free binary BHJ OSCs.

The dependence of electrocatalytic HER activity of decorated MoS2 with Cu nanoclusters

Molybdenum disulfide is a potential electrocatalytic material for water splitting with excellent stability and durability. Here, the electrocatalytic hydrogen evolution reaction performance of Molybdenum disulfide nanosheets decorated with copper nanoclusters was investigated. The Cu@MoS2–1:10 exhibited remarkable hydrogen evolution reaction activity, with an overpotential as low as 150 mV under acidic conditions. The First-principles calculations further confirmed the superior electrocatalytic performance of Cu@MoS2, with a minimum hydrogen adsorption free energy of -0.10 eV. The improved electrocatalytic activity of Cu@MoS2 arises from the accelerated charge migration at the interface. And the addition of Cu increases the number of active sites on the surface of MoS2. This work could offer insights into the advancement of additional non-precious metals and transition metal dichalcogenides.

Ultrahigh Polarization of Emitted Light by Quenched Emissive Material

AbstractThe emission of highly polarized light by organic light‐emitting diodes (OLEDs) is crucial for various applications; however, achieving such emission requires the use of polarizers, which reduce the device efficiency and durability. In this study, ultrahigh‐polarized light with a polarization ratio (PR) of 407:1 is achieved via the rapid thermal quenching (RTQ) of OLEDs. Poly(3,4‐ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) films, molybdenum disulfide (MoS2) nanosheets, and tungsten disulfide (WS2) nanosheets are applied as hole transport layers and surface‐alignment layers through surface treatment, including rubbing and/or ion‐beam exposure to align the molecules of the emissive materials, namely, {poly(9,9‐dioctylfluorene‐alt‐benzothiadiazole) (F8BT). Quenching is performed at 240 °C, at which F8BT has a nematic liquid crystal (NLC) phase with high molecular ordering. Upon quenching, the high molecular ordering of the NLC‐phased emissive layer instantaneously froze via RTQ, leading to the emission of highly polarized light. Consequently, the PEDOT:PSS‐, MoS2‐, and WS2‐based OLEDs exhibit ultrahigh PRs of 407:1, 349:1, and 328:1, respectively, for photoluminescence at a 540 nm peak wavelength. In contrast, for electroluminescence, the PEDOT:PSS‐based OLED exhibits a high PR of 395:1. This result is the best reported to date and is comparable to the PRs generated by polarizers, indicating that quenching can be utilized for the development of ultrahigh‐polarized light‐emitting devices.