Dissipation Of Excess Pore Water Pressure Research Articles

Consolidation and seepage solutions in enclosure space based on non-zero-constant values boundary.

Research is ongoing to find solutions to the problem of Consolidation and seepage in saturated clay in enclosure space. Firstly, the boundary of non-zero-constant values is established, considering the seepage boundary of the clay is affected by pumping water or lowering boundary pressure on the site. Secondly, the differential equation is established to reflect the spatial and temporal variations of excess pore water pressure dissipation in the clay in enclosure space, and the solution is derived using variable separation methods. Finally, based on results of the solution derived, contour maps of the water pressure are drawn corresponding with the different inhomogeneous boundary conditions.

Assessment of Axial Resistance of Piles Considering Consolidation Setup and Aging Setup Using Direct Pile Cone Penetration Test Methods

This paper focuses on evaluating the increase in axial pile resistance subjected to both consolidation and aging setups. Consolidation and aging setup models were first developed to estimate the setup parameters based on databases collected from literature, which include 10 instrumented piles for consolidation setup and 26 test piles for long-term aging. The eight top-performing pile cone penetration test (CPT) methods that were evaluated in a previous study were used to estimate the side resistance of soil layers at 14 days after pile driving. The developed consolidation and aging setup models were then used to extrapolate the results to evaluate the side resistance of each soil layer at the end of consolidation and for long-term aging. The estimated side and total resistances were compared with the measurements from pile load tests considering both consolidation and aging setups. The resistances estimated before and after completion of excess pore water pressure dissipation indicates that significant aging takes place after consolidation setup. The value of consolidation setup parameter ( Ac) was 0.53, and, for aging, the setup parameter ( Ag) was 0.23 in clay and 0.16 in sand. The results show that all pile CPT methods with/without using a consolidation setup model tend to underestimate the unit side resistance of clay soil layers. The use of pile CPT methods in combination with an aging model improved the accuracy of pile CPT methods, and this was verified using load test results for five piles subjected to aging. The Philipponnat and University of Florida (UF) methods showed the best performance on estimating the total resistance of piles subjected to aging.

Correction effect of jet-grouting on high-speed railway subgrade lateral deformation

Viable remediation of the large lateral deformation of high-speed railway (HSR) subgrades, especially in soft soil areas, is still absent. An integrated rectification scheme of high-pressure jet-grouting (HPJG) combined with stress-release techniques was conducted to rectify the large lateral deformation of an operational HSR subgrade in the soft soil area of China, but without any refined design and mechanical analysis before rectification due to the emergency. The objective of the study is to post-evaluate the rectification effects utilising field monitoring data and numerical calculations. The monitoring data showed that the maximum lateral deviation of the subgrade was 69.1 mm, which almost met the expected correction requirements. However, the influence of the excess pore water pressure (EPWP) dissipation on the correction deviation was not considered in the scheme. Therefore, a numerical model was established to further investigate this effect and corresponding mitigation methods. The calculated results revealed that EPWP in the foundation dissipated mostly within 6 months after rectification, and the deformation loss accounted for 30.7% of the total deviation. Prolonging the interval of two-row pile construction can be a plausible approach to mitigate the deviation loss. The findings provide a feasible method for correcting large lateral deformation of HSR subgrades.

Simplified analytical solution for time dependent deformation of soft soil improved with pervious column considering load transfer between column and soil

This paper presents a simplified analytical solution to analyse the coupled excess pore water pressure dissipation and deformation response of a composite stone column – soft soil foundation. The mathematical formulation is derived considering the combined radial – vertical flows of excess pore water pressure in stone column and soft soil areas (orthotropic permeability for each area), and adopting the settlement pattern for the composite ground suggested by an existing study in the literature. The homogeneous consolidation formulations are solved first to develop Green’s function for final excess pore water pressure solutions, employing the method of separation of variables and eigenfunction expansion technique. Then, the final solutions for excess pore water pressure corresponding to the nonhomogeneous consolidation formulations are derived in terms of Green’s formula, which can be expanded readily into a double series solution. The obtained analytical solutions can be used to examine the variation of excess pore water pressure against time at any point in the composite foundation. Thus, the consolidation settlements of stone column and soft soil areas and the differential settlement between them can be captured. The average differential settlement between the soil and column areas is used to compute the shear strains and shear stresses in the composite ground during the consolidation process. The proposed analytical solution is validated via a worked example in conjunction with a verification exercise against finite element simulation. The analytical predictions are presented in terms of the total vertical stress variations and excess pore water pressure dissipations against depth and time, the settlements and average degrees of consolidation for stone column and surrounding soft soil, and the shear stress distribution in the soil region. The capability of proposed analytical solution is also verified against field measurements of a full-scale test of soil - column composite ground (pervious column). The verifications show that the obtained analytical solution can predict the coupled excess pore water pressure dissipation – deformation response of soft soils improved by pervious columns such as stone columns and soil- deep cement mixing columns reasonably well.

Analytical solution for consolidation of saturated viscoelastic soils around tunnels with general Voigt model

This paper presents a novel analytical solution for the consolidation behavior of viscoelastic saturated soft soil subjected to large-scale ground loading. The rheological properties of clay are described using the general Voigt model. Based on the Terzaghi-Rendulic theory, the governing equations for the dissipation of excess pore water pressure in the surrounding soil mass of a tunnel are established under the first and second boundary conditions. The governing equations are solved using the complex variable method. The obtained solutions are verified by reducing them to the forms of three traditional rheological models, demonstrating the reliability of the proposed approach. Finally, based on the established solutions, the dissipation characteristics of excess pore water pressure around the tunnel are analyzed. The case results indicate that the soil permeability coefficient (k), the independent Newtonian viscosity coefficient (K0) and Hooke’s spring modulus (E0) in the general Voigt model have significant influences on the dissipation of excess pore water pressure and the degree of consolidation. A larger k, K0, and E0 lead to faster dissipation and consolidation development, while a greater tunnel buried depth (b) results in slower consolidation process. The influence of k on excess pore water pressure dissipation is more significant than that of K0 and E0. For the first boundary type, consolidation is instantaneous when k > 0.1 m/d. For the second type, when k < 0.0001 m/d, excess pore pressure remains unchanged within 100 d. The permeability condition of the tunnel has a considerable impact on the distribution of excess pore water pressure in the soil layer directly above the crown. When the tunnel is fully permeable, the effects of k, K0, and E0 on the dissipation of excess pore water pressure are more pronounced in the early stage, with almost complete dissipation of excess pore pressure above the tunnel before 100 d. However, when the tunnel is completely impermeable, their effects are more prominent in the later stage, and by 100 d, the maximum excess pore pressure within the depth range is 25 % of the initial.

A semi-analytical solution for consolidation of soft ground improved by locally permeable pipe piles under time-dependent loads

Excessive pore-water pressure in soft soil can compromise pile bearing capacity, leading to foundation failure and posing a risk to structure stability. Hence expedited dissipation of excess pore-water pressure is critical. Permeable pipe piles offer an alternative to accelerating this consolidation process. In this study, a modified vertical equal-strain consolidation model of composite foundations with locally permeable pipe piles under arbitrary time-dependent loads is investigated. The integral transform and boundary transform methods are used to obtain a semi-analytical solution to this consolidation problem. The proposed solution’s validity and correctness are further confirmed via theoretical degradation and numerical analysis. Subsequently, a sensitivity analysis in terms of opening parameters, pile-soil modulus ratio, soil’s hydraulic conductivity ratio and pile’s length-diameter ratio is conducted. The results indicate that the consolidation rate of the permeable pipe pile composite foundations demonstrates a significant enhancement over impermeable pipe pile composite foundations, especially for deep and soft foundations with high hydraulic conductivity ratios. The consolidation efficiency improves with the increase of pile’s opening ratio, opening length and opening depth until it reaches a plateau at larger opening parameters. The research can provide theoretical support for design and construction of infrastructure with permeable pipe pile composite foundations.

Modelling biogeochemical clogging affecting piezometers in acid sulfate soil terrain

This study offers an analytical solution for radial consolidation that captures the biogeochemical clogging effect in acid sulfate soils. Field sites and personal communication with industry practitioners have provided evidence of piezometers exhibiting retarded pore pressure readings that do not follow conventional soil consolidation and seepage principles when installed in coastal acidic floodplains. This retarded response together with a variation in pH, ion concentrations, and piezometric heads provided evidence of clogging at and around the piezometers. This paper uses the proposed biogeochemical clogging model, which is an analytically derived system of equations to estimate the excess pore water pressure dissipation of piezometers installed in clogging-prone acid sulfate soils. The inclusion of the total porosity reduction attributed to biological and geochemical clogging improves the predictions of the retarded dissipation of excess pore pressure, especially after about 1 year. This method is validated for two previously identified acidic field sites in coastal Australia, where piezometers measured a very slow rate of dissipation. It is concluded that this model has potential to accurately monitor the performance of critical infrastructure, such as dams and embankment foundations built on acidic terrain.

Set-up effect of large-diameter open-ended thin-walled pipe piles driven in clay

A finite element method (FEM) model was developed to investigate the distribution and dissipation of the soil excess pore water pressure (EPWP) around large-diameter open-ended thin-wall steel pipe piles (LOTPs) driven by impact loads into saturated clay, in addition to the set-up effect of LOTPs. The initial pore water pressure (PWP) distribution and vertical bearing capacity of LOTPs after EPWP dissipation were analyzed through this numerical model. The EPWP mapped onto the FEM model was compared with previously reported distribution curves, revealing that the numerical results were generally similar to those of previous theoretical models. Following dissipation for 28 days, the load–settlement curves of LOTPs were compared with the results of several specifications; this indicated that the larger the LOTP diameter, the greater the similarity between axial bearing capacities calculated via the FEM model and the specifications. This FEM model could generally satisfy the requirements for analyzing the set-up effect of LOTPs. It was also found that the LOTP capacities were overestimated when the EPWP was neglected. Beyond 28 days, the pile bearing capacity did not increase because the dissipation of the EPWP was almost fully developed. An equation for predicting the set-up effect of LOTPs installed using impact hammers is also presented.

Vacuum preloading combined with surcharge preloading method for consolidation of clay-slurry ground: A case study

A reclamation project was undertaken in Zhuhai, China, covering an area of 11.35 km2 with a clay-slurry thickness of 30 m. It is interesting to find a good reinforcement method, which is more suitable for strengthening such a large-scale dredged clay-slurry ground. Evidence from engineering practice shows that vacuum preloading or vacuum preloading combined with surcharge preloading method technology has certain advantages. However, further data is required to verify their performance in the field. This paper presents a case study using the conventional vacuum preloading and vacuum preloading combined with surcharge preloading method (vacuum pressure of 90 kPa, surcharge height of 3 m) to improve the thick clay-slurry ground for a subgrade engineering project in Zhuhai, China. A series of field monitoring, in-situ tests, and laboratory tests were performed to evaluate their treatment effect by analysis of vacuum degree, ground surface settlement, layered settlement, consolidation degree, lateral displacement, excess pore water pressure dissipation, and vane shear strength. The results showed that the ground treated via vacuum preloading combined with surcharge preloading method was more effective than conventional vacuum preloading. The vacuum degree of vacuum preloading combined with surcharge preloading method was slightly lower than that of conventional vacuum preloading, decreasing with depth. The settlement is increased by 55.56%, average consolidation degree is enlarged by 40.9%, lateral displacement can be augmented by 2.4 times, pore water pressure coefficient is less than 0.6, and undrained shear strength is amplified by 22.2%. These findings can be used to guide the design of the combined preloading method of the subgrade engineering project along the east coast of China.

Shaking table tests on the liquefaction-induced uplift displacement of circular tunnel structure

Underground structures are susceptible to float and move upward during earthquakes when located in a liquefiable soil deposit. There are examples of this phenomenon in past major earthquake events. In this study, the uplift of circular tunnels in a liquefiable sand layer was investigated with a series of shaking table tests. The research has focused on the buried depth of the tunnel, tunnel diameter, tunnel weight, liquefaction extent, uplift mechanism, and factor of safety against liquefaction-induced uplift. According to the test results, the shallow buried depth, larger diameter, and lower weight can intensify the tunnel uplift, so the displacement in post-liquefaction time continues at the same rate as during the shaking time. Due to the shear-induced dilation, pore water pressure generation around the tunnel was reduced compared with that of the free field. The excess pore water pressure dissipation in the soil overlying the uplifted tunnel was significant, which leads to suction in the soil deposit. Furthermore, the acceleration response of overlying soil with the uplifted tunnel was similar to that of the free field. However, the soil acceleration response around the tunnel without uplift was similar to the base motion.

Mud pumping in high-speed railway: in-situ soil core test and full-scale model testing

Mud pumping induced by moving train loads on rainwater-intruded roadbed causes intensive track vibrations and threatens safety of high-speed trains. In this paper, a vehicle–track–subgrade finite element model was established to analyze the dynamic responses of a ballastless track, and results showed that the concrete base and roadbed were detached because of the whipping effect arising from the rainwater intrusion channel. An in-situ soil core test showed that the intruded rainwater accumulated in roadbed to form standing water and saturated the roadbed. The flapping action of the concrete base caused by the whipping effect led to mud formation mixed with fine particles and rainwater, which migrated upward under the pore-water pressure (PWP) gradient. Mud pumping resulted from continuous particle migration in the saturated roadbed under moving train loads: under normal roadbed condition, coarse and fine particles were uniformly distributed in the roadbed; in early period of mud pumping, fine particles migrated downward to bottom of the roadbed because of the rainwater infiltration flow; in middle stage of mud pumping, fine particles migrated upward and gathered at the roadbed surface under PWP gradient; in later period of mud pumping, fine particles were entrained and removed with the dissipation of excess PWP. Moreover, a full-scale physical model was established to reproduce mud pumping, and polyurethane injection remediation against mud pumping was validated on this physical model. The remediation method was applied to an in-situ mud pumping. The deviation of the vertical track profile reduced remarkably and remained at a low level within half a year, showing a good long-term service performance of the polyurethane remediated roadbed.

Excess Pore Water Pressure Generation, Distribution and Dissipation in Self-boring Pressuremeter Test: Numerical Analysis

Excess Pore Water Pressure Generation, Distribution and Dissipation in Self-boring Pressuremeter Test: Numerical Analysis

Time-dependent evolution of bearing capacity of driven piles in clays

Analysis of the time-dependent variation in the axial capacity of driven piles is difficult yet critical for geotechnical engineers. In this work, to investigate the short-term evolution of the bearing capacity of driven piles, a two-dimensional finite-element (FE) model was developed using the Abaqus program. Pile installation, soil consolidation and loading were incorporated in an integrated FE model. Changes in the excess pore pressure and the void ratio of the surrounding soil were investigated to evaluate the consolidation mechanism. The findings revealed that excess pore water pressure dissipation was the primary cause of the short-term evolution of the pile's bearing capacity. The dissipation of excess pore water pressure lowered the void ratio and increased the strength and stiffness of the surrounding soil. The effect of the permeability coefficient was also assessed. The permeability coefficient was found to affect the rate of evolution but not its magnitude. A centrifuge model test was used to verify the numerical results. The findings of this study may serve as a guide for improved design and construction of driven piles.

Effect of soil gradation on embankment response during liquefaction: A centrifuge testing program

This paper describes a centrifuge study undertaken to investigate how sand gradation affects the system-level performance of embankments subjected to strong shaking. Current analysis and design practices are primarily based on knowledge from case history records of liquefaction, with the majority of those from sites consisting of clean, poorly graded sands. The narrow range of gradation characteristics represented in the case history database poses a challenge during the analysis of embankment structures traditionally constructed with, or founded on, more broadly graded soils. The tests herein were designed to elucidate how embankments uniformly constructed with a well graded and poorly graded sand perform differently during earthquake shaking. A centrifuge experiment test program was developed and conducted using the 9-m-radius centrifuge at the UC Davis Center for Geotechnical Modeling. The experiment design consisted of two submerged 10-degree embankments positioned side-by-side in the same rigid model container, with one embankment constructed with poorly graded sand and the other with well graded sand. The embankments were dry pluviated to the same relative density, but the absolute densities of the sands were different. The embankments were identically instrumented with dense arrays of in-situ sensors beneath the level ground above the slope and in the mid-slope to measure the dynamic response during liquefaction. Results showed that embankments constructed at equal relative densities would both liquefy (i.e., ru reach 1.0), but deformations were less severe for the embankments constructed with the well graded sand. Greater resistance to the generation and faster dissipation of excess porewater pressures, coupled with stronger dilatancy of the well graded sand increased embankment stability, curtailing liquefaction-induced deformations.

Analysis of one‐dimensional nonlinear rheological consolidation of saturated clay considering self‐weight stress and Swartzendruber's flow rule

AbstractConsidering the nonlinear rheological properties of saturated clay, the modified unified hardening (UH) constitutive relation was introduced to describe the nonlinear rheological deformation. Meanwhile, Swartzendruber's flow law was used to simulate the non‐Darcian flow of pore water in the progress of rheological consolidation. Consequently, a nonlinear rheological consolidation model (NRCM), for one‐dimensional consolidation, that simultaneously incorporates nonlinear stress‐strain‐time relationship, Swartzendruber's flow, self‐weight stress, and variable permeability coefficient has been developed here. The finite volume method (FVM) was utilized to solve the NRCM system, and its effectiveness was verified by comparing with the existing consolidation data. The parametric analysis results indicate that the soil's nonlinear rheological effect induced the excess pore water pressure (EPWP)’s accumulation in the initial loading. This phenomenon became more significant when considering the self‐weight stress or as the initial overconsolidated parameter, soil thickness, and seepage parameter increased. In contrast, it weakened with the increase of external loading. Additionally, considering the self‐weight stress slowed down the whole dissipation of EPWP in the initial period of loading. Nevertheless, it accelerated the nonlinear consolidation process in the middle and late loading stages.

One-dimensional consolidation of multilayered aquifer systems with viscoelastic properties induced by time-dependent groundwater drawdown

Most analytical and semi-analytical models for pumping-induced land subsidence invoke the simplifying assumptions regarding characteristics of geomaterials, as well as the pattern of drawdown response to pumping. This paper presents an analytical solution for one-dimensional consolidation of the multilayered soil due to groundwater drawdown, in which viscoelastic property and time-dependent drawdown are taken into account. The presented solution is developed by using the boundary transformation techniques. The validity of the proposed solution is verified by comparing with a degenerated case for a single layer, as well as with the numerical solutions and experimental results for a two-layer system. The difference between the average consolidation degree Up, defined by hydraulic head, and Us, defined by total settlement, is discussed. Detailed parametric studies are conducted to reveal the effects of viscoelastic properties and drawdown patterns on the consolidation process. It is revealed that while the effect of different drawdown response patterns is significant during the early–intermediate stages of consolidation, the viscoelastic properties may have a more dominant influence on long-term consolidation behaviour, depending on the values of the material parameters, which are reflected in both the deformation process of soil layers and the dissipation of excess pore-water pressure.

Liquefaction and post-liquefaction resistance of sand reinforced with recycled geofibre

The present study provides an insight into the effect of recycled carpet fibre on the mechanical response of clean sand as backfill material subjected to monotonic loading and cyclic loading as well as post-liquefaction resistance of both unreinforced and carpet fibre reinforced soils. To achieve these goals, a series of multi-stage soil element tests under cyclic loading event resulting in liquefaction followed by undrained monotonic shearing without excess pore water pressure dissipation as well as a series of monotonic undrained shear test is conducted. All the specimens are isotropically consolidated under a constant effective confining stress of 100 kPa by considering the effect of cyclic stress ratio and carpet fibre content ranging from 0.25% to 0.75%. The obtained results revealed the efficiency of carpet fibre inclusion in increasing the secant shear modulus and ductility of clean sand under monotonic shearing without previous loading history. The impact of carpet fibre inclusion on the trend of cyclic excess pore water pressure generation and cyclic stiffness degradation was minimal. However, adding carpet fibre significantly improved both liquefaction and post-liquefaction resistances of clean sand. The liquefaction resistance of clean sand, at a constant 15 loading cycles, improved by 26.3% when the soil was reinforced with 0.75% recycled carpet fibre. In addition, the initial shear modulus of the liquefied specimen significantly increased by adding recycled carpet fibre.

Study on the Correlation between Soil Consolidation and Pile Set-Up Considering Pile Installation Effect

In saturated fine-grained soil, the development and dissipation of excess pore water pressure (EPWP) during and after pile jacking change the effective stress of the surrounding soil, and thereby affect the pile set-up. In this paper, the entire process of steel-pipe pile jacking (the installation process and the subsequent consolidation phase) is simulated with three-dimensional (3D) finite element models, considering the pore water effect. After the model verification, a comprehensive numerical analysis was performed to investigate the development and dissipation of EPWP, changes in soil stress state, and the side shear resistance of pile with time after installation. On this basis, not only the influence of ks, cu, E, and OCR on EPWP generation during pile jacking and subsequent soil consolidation effect after pile installation but also the correlation between pile set-up and EPWP dissipation is investigated.

Green’s function analytical solution for free strain consolidation of soft soil improved by stone columns subjected to time-dependent loading

This paper proposes an analytical solution in terms of Green’s function formulations for axisymmetric consolidation of a stone column improved soft soil deposit subjected to time-dependent loading under free strain condition. The mathematical derivations incorporate the pore water flows in radial and vertical directions in stone column and soft soil synchronously. The capabilities of the proposed analytical solution are evaluated via worked examples investigating the influences of three common time-dependent external surcharges (namely step, ramp and sinusoidal loadings) on consolidation response of the composite ground. The examples show that a faster increase of load from an initial surcharge to an expected loading might generate more significant excess pore water pressure to be dissipated during the early stages of consolidation, but the dissipation rate in soft soil would speed up significantly afterwards. The column and soil settlements along with the differential settlement between them also proceed faster corresponding to the acceleration of loading – unloading processes. Finally, the proposed analytical solution is employed to evaluate the excess pore water pressure dissipation rate at an investigation point in soft clay of a case history foundation. The calculation results exhibit a reasonable agreement with field measurement data when various constant values of stress concentration ratio are substituted into the solution to reflect the increase of stress concentration ratio with consolidation time in real practice.

Laboratory Model Test and Analysis of Excess Pore Water Pressure Dissipation of Pile Driven by Tapered - Perforated Tubular Pipe Pile

Through methods based on the indoor model test, the use of static pressure pile with three different hole arrangement and three different kinds of taper cone - bore log shape composite pipe pile bored into soil by static pressure,and after observing the excess pore water pressure caused by pile driving when testing, and analyzing the process of various pipe pile static pressure, the change rule of the excess pore water pressure varying with taper hole arrangement, size, radial distance, pile depth has been gotten. It is found that stellate shape has the best dissipation rate of excess pore water pressure under the condition of hole arrangement and taper 1/70, which is of certain guiding significance for promoting the engineering application of tapered - perforated tubular piles.