Disc Failure Research Articles

A new dynamic six degrees of freedom disc-loading simulator allows to provoke disc damage and herniation.

The cause of disc herniation is not well understood yet. It is assumed that heavy lifting and extreme postures can cause small injuries starting either in the inner anulus or from the outside close to the endplate. Such injuries are accumulated over years until its structure is weakened and finally a single loading event leads to a sudden failure of the last few intact lamellae. This paper describes a novel, custom-developed dynamic 6-DOF disc-loading simulator that allows complex loading to provoke such disc damage and herniations. The machine's axes are driven by six independent servomotors providing high loads (10 kN axial compression, 2 kN shear, 100 Nm torque) up to 5Hz. A positional accuracy test was conducted to validate the machine. Subsequently, initial experiments with lumbar ovine motion segments under complex loading were performed. After testing, the discs were examined in an ultra-high field MRI (11.7 T). A three-dimensional reconstruction was performed to visualise the internal disc lesions. Validation tests demonstrated positioning with an accuracy of ≤0.08°/≤0.026mm at 0.5Hz and ≤0.27°/≤0.048mm at 3.0Hz with amplitudes of ±17°/±2mm. Typical failure patterns and herniations could be provoked with complex asymmetrical loading protocols. Loading with axial compression, flexion, lateral bending and torsion lead in 8 specimens to 4 herniated discs, two protrusions and two delaminations. All disc failures occurred in the posterior region of the disc. This new dynamic disc-loading simulator has proven to be able to apply complex motion combinations and allows to create artificial lesions in the disc with complex loading protocols. The aim of further tests is to better understand the mechanisms by which disc failure occurs at the microstructural level under different loading conditions. Visualisation with ultra-high field MRI at different time points is a promising method to investigate the gradual development of such lesions, which may finally lead to disc failure. These kinds of experiments will help to better investigate the mechanical failure of discs to provide new insights into the initiation of intervertebral disc herniation. This device will also serve for many other applications in spine biomechanics research.

Thalidomide represses inflammatory response and reduces radiculopathic pain by inhibiting IRAK-1 and NF-κB/p38/JNK signaling

Intervertebral disc (IVD) disease, the most common cause of disc failure and low back pain, is characterized by age-related changes in the adult disc. In this study we aimed to analyze the potential of thalidomide for the treatment of IVD disease, through identifying and explaining its anti-inflammatory and anti-catabolic activity in both in vitro IVD cell culture and in vivo animal model. Inflammatory response was induced by IL-1β, then the activity and expression of inflammatory mediators and pathways were assessed in the presence or absence of thalidomide. The p38 inhibitor SB203580 was also used to investigate the involvement of the MAPK pathway in the observed effects. Moreover the analgesic properties of thalidomide were analyzed by the von Frey filament test in Sprague–Dawley rats. Our results indicated that thalidomide significantly inhibited the expression of pro-inflammatory mediators and matrix metalloproteinases in vitro, as well as radiculopathic pain in vivo, most probably by modulation of the activity of IRAK-1 and its downstream effectors p38, JNK and NF-κB. Our current study strongly supports the potential of thalidomide for the treatment of pain and inflammation in degenerative disc disease.

Biomechanical effects of fusion levels on the risk of proximal junctional failure and kyphosis in lumbar spinal fusion surgery

BackgroundSpinal fusion surgery is a widely used surgical procedure for sagittal realignment. Clinical studies have reported that spinal fusion may cause proximal junctional kyphosis and failure with disc failure, vertebral fracture, and/or failure at the implant-bone interface. However, the biomechanical injury mechanisms of proximal junctional kyphosis and failure remain unclear. MethodsA finite element model of the thoracolumbar spine was used. Nine fusion models with pedicle screw systems implanted at the L2–L3, L3–L4, L4–L5, L5–S1, L2–L4, L3–L5, L4–S1, L2–L5, and L3–S1 levels were developed based on the respective surgical protocols. The developed models simulated flexion–extension using hybrid testing protocol. FindingsWhen spinal fusion was performed at more distal levels, particularly at the L5–S1 level, the following biomechanical properties increased during flexion–extension: range of motion, stress on the annulus fibrosus fibers and vertebra at the adjacent motion segment, and the magnitude of axial forces on the pedicle screw at the uppermost instrumented vertebra. InterpretationsThe results of this study demonstrate that more distal fusion levels, particularly in spinal fusion including the L5–S1 level, lead to greater increases in the risk of proximal junctional kyphosis and failure, as evidenced by larger ranges of motion, higher stresses on fibers of the annulus fibrosus and vertebra at the adjacent segment, and higher axial forces on the screw at the uppermost instrumented vertebra in flexion–extension. Therefore, fusion levels should be carefully selected to avoid proximal junctional kyphosis and failure.

Archival-grade optical disc design and international standards

Optical discs currently on the market exhibit large variations in life span among discs, making them unsuitable for certain business applications. To assess and potentially mitigate this problem, we performed accelerated degradation testing under standard ISO conditions, determined the probable disc failure mechanisms, and identified the essential criteria necessary for a stable disc composition. With these criteria as necessary conditions, we analyzed the physical and chemical changes that occur in the disc components, on the basis of which we determined technological measures to reduce these degradation processes. By applying these measures to disc fabrication, we were able to develop highly stable optical discs.

Tanshinone IIA represses inflammatory response and reduces radiculopathic pain by inhibiting IRAK-1 and NF-κB/p38/JNK signaling

Intervertebral disc (IVD) disease, a most common cause of disc failure and low back pain, is characterized by age-related changes in the adult disc. In this study we aimed to investigate the potential of Tanshinone IIA (TSA) for the treatment of IVD disease, through exploring its anti-inflammatory and anti-catabolic activities in both in vitro IVD cell culture and in vivo animal models. After the inflammatory response was induced in IVD cells by IL-1β, the activity and expression of inflammatory mediators, and potentially involved pathways were investigated in the presence or absence of TSA. The p38-MAPK inhibitor, SB239063, was also used to investigate the involvement of the MAPK signaling pathway in the observed effects. Meanwhile, the analgesic properties of TSA were analyzed by the von Frey filament test in Sprague–Dawley rats. Our results indicated that TSA significantly inhibited the expression of pro-inflammatory mediators and matrix metalloproteinases in vitro, as well as radiculopathic pain in vivo, probably by modulation of the activity of interleukin-1 receptor-associated kinase 1 (IRAK-1) and its downstream effectors p38, JNK and NF-κB. Our current study strongly demonstrates the potential of TSA for the treatment of inflammation and followed pain in degenerative disc disease.

"Surprise" Loading in Flexion Increases the Risk of Disc Herniation Due to Annulus-Endplate Junction Failure: A Mechanical and Microstructural Investigation.

Microstructural investigation of compression-induced herniation of the flexed lumbar disc. To provide a microstructural analysis of the mechanisms of annular wall failure in healthy discs subjected to flexion and a rate of compression comparable with the maximum rate at which the muscles of the spinal column can generate a force. Clinical evidence indicates the involvement of the endplate in herniation. It is known that both an elevated rate of compression and a flexed posture are necessary to cause disc failure either within the midspan of the annulus or at the annular-endplate interface. However, the question of what effect a sudden or "surprise" loading might have on the mode of failure is, as yet, unanswered. Twenty-four healthy mature ovine lumbar motion segments were compressed to failure in high physiological flexion (10º). This occurred over approximately 5 mm of crosshead displacement in 0.75 seconds that resulted in a displacement rate of 400 mm/min (defined as a "surprise" rate) and was intended to simulate the maximum rate at which the muscles of the spinal column can generate a force. The damaged discs were then analyzed microstructurally. Fifty-eight percent of discs suffered annular-endplate junction rupture, 25% suffered midspan annular rupture, and the balance of 17% endplate fracture. Microstructural analysis indicated that annular rupture initiated at the endplate apical ridge in the mid-to-outer region of the annulus in both annular-endplate and midspan annulus rupture. Motion segments subjected to a "surprise" loading rate are likely to fail via some form of annular rupture. Failure under such sudden loading occurs mostly via rupture of the annular-endplate junction and is thought to arise from a rate-induced mechanostructural imbalance between the annulus and the endplate. N/A.

Materials and Their Failure Mechanisms in Total Disc Replacement

Adults suffering from lower back pain often find the cause of pain is degenerative disc disease. While non-surgical treatment is preferred, spinal fusion and total disc replacement remain surgical options for the patient. Total disc replacement is an emerging and improving treatment for degenerative discs. This paper provides a review of lumbar disc replacement for treatment of lower back pain. The mechanics and configuration of the natural disc are first discussed, followed by an introduction of treatment methods that attempt to mimic these mechanics. Total disc replacement types, materials, and failure mechanisms are discussed. Failure mechanisms primarily involve biochemical reactions to implant wear, as well as mechanical incompatibility of the device with natural spine motion. Failure mechanisms include: osteolysis, plastic deformation of polymer components, pitting, fretting, and adjacent level facet and disc degeneration.

Steam turbine rotor discs failure evaluation and repair process implementation

Two rotor discs failed in a 84-MW unit installed in a power plant. The failure was evidenced by large circumferential fractures of blades attachments in both discs. Disc failure was evaluated by investigating rotor operation history, steady state stress analysis by finite element (FEA), disc fracture surface fractography and deposit evaluation. It was found that this disc failure was driven by stress corrosion due to significant static stresses, humid ambient operation and disc material susceptibility. To correct disc failure and restore turbine original characteristics, a disc welding repair procedure was developed. This repair process was implemented and rotor discs restored by weld deposition, post weld heat treatment and machining. As a result, the rotor was returned to service and its useful life extended.

Epigallocatechin 3-gallate suppresses interleukin-1β-induced inflammatory responses in intervertebral disc cells in vitro and reduces radiculopathic pain in rats.

Intervertebral disc (IVD) disease, which is characterised by age-related changes in the adult disc, is the most common cause of disc failure and low back pain. The purpose of this study was to analyse the potential of the biologically active polyphenol epigallocatechin 3-gallate (EGCG) for the treatment of painful IVD disease by identifying and explaining its anti-inflammatory and anti-catabolic activity. Human IVD cells were isolated from patients undergoing surgery due to degenerative disc disease (n = 34) and cultured in 2D or 3D. An inflammatory response was activated by IL-1β, EGCG was added, and the expression/activity of inflammatory mediators and pathways was measured by qRT-PCR, western blotting, ELISA, immunofluorescence and transcription factor assay. The small molecule inhibitor SB203580 was used to investigate the involvement of the p38 pathway in the observed effects. The analgesic properties of EGCG were analysed by the von Frey filament test in Sprague-Dawley rats (n = 60). EGCG significantly inhibited the expression of pro-inflammatory mediators and matrix metalloproteinases in vitro, as well as radiculopathic pain in vivo, most probably by modulation of the activity of IRAK-1 and its downstream effectors p38, JNK and NF-κB.

Localized strain measurements of the intervertebral disc annulus during biaxial tensile testing

Both inter-lamellar and intra-lamellar failures of the annulus have been described as potential modes of disc herniation. Attempts to characterize initial lamellar failure of the annulus have involved tensile testing of small tissue samples. The purpose of this study was to evaluate a method of measuring local surface strains through image analysis of a tensile test conducted on an isolated sample of annular tissue in order to enhance future studies of intervertebral disc failure. An annulus tissue sample was biaxial strained to 10%. High-resolution images captured the tissue surface throughout testing. Three test conditions were evaluated: submerged, non-submerged and marker. Surface strains were calculated for the two non-marker conditions based on motion of virtual tracking points. Tracking algorithm parameters (grid resolution and template size) were varied to determine the effect on estimated strains. Accuracy of point tracking was assessed through a comparison of the non-marker conditions to a condition involving markers placed on tissue surface. Grid resolution had a larger effect on local strain than template size. Average local strain error ranged from 3% to 9.25% and 0.1% to 2.0%, for the non-submerged and submerged conditions, respectively. Local strain estimation has a relatively high potential for error. Submerging the tissue provided superior strain estimates.

How Healthy Discs Herniate

Microstructural investigation of compression-induced disruption of the flexed lumbar disc. To provide a microstructural analysis of the mechanisms of annular wall failure in healthy discs subjected to flexion and an elevated rate of compression. At the level of the motion segment failure of the disc in compression has been extensively studied. However, at the microstructural level the exact mechanisms of disc failure are still poorly understood, especially in relation to loading posture and rate. Seventy-two healthy mature ovine lumbar motion segments were compressed to failure in either a neutral posture or in high physiological flexion (10°) at a displacement rate of either 2 mm/min (low) or 40 mm/min (high). Testing at the high rate was terminated at stages ranging from initial wall tearing through to facet fracture so as to capture the evolution of failure up to full herniation. The damaged discs were then analyzed microstructurally. Approximately, 50% of the motion segments compressed in flexion at the high rate experienced annulus or annulus-endplate junction failure, the remainder failed via endplate fracture with no detectable wall damage. The average load to induce disc failure in flexion was 18% lower (P < 0.05) than that required to induce endplate fracture. Microstructural analysis indicated that wall rupture occurred first in the posterior mid-then-outer annulus. Disc wall failure in healthy motion segments requires both flexion and an elevated rate of compression. Damage is initiated in the mid-then-outer annular fibers, this a likely consequence of the higher strain burden in these same fibers arising from endplate curvature. Given the similarity in geometry between ovine and human endplates, it is proposed that comparable mechanisms of damage initiation and herniation occur in human lumbar discs. N/A.

ISSLS Prize Winner

A prospective multimodal study including clinical, radiological, serial postcontrast magnetic resonance imaging, intraoperative findings, and histopathological study. To document in vivo, the site of anatomical failure in lumbar disc herniation (LDH). Although in vitro mechanical disruption studies have implicated both the endplate junction (EPJ) and the annulus fibrosus (AF) as the site of failure in LDH, there are no in vivo human studies to document the exact anatomy of failure. One hundred eighty-one consecutive patients requiring microdiscectomy at a single level formed the study group. The status of the endplate and AF in the operated level (study discs) and the other discs (control) were evaluated by plain radiograph, thin slice computed tomographic scan, plain and contrast magnetic resonance imaging, intraoperative examination, and histopathological analysis. LDH due to EPJ failure (EPJF- type I herniation) was more common (117; 65%) than annulus fibrosis rupture. Herniated discs had a significantly higher incidence of EPJF than control discs (P < 0.0001). The EPJF was evident radiologically as vertebral corner defect in 30 patients, rim avulsion in 46, frank bony avulsions in 24, and avulsion at both upper and lower EP in 4. Thirteen discs with normal EP radiologically had cartilage or bone avulsion intraoperatively. Sixty-four discs (35%) had intact EP of which annular high intensity zone was found in 21 (11%), suggesting a disruption of AF (type II herniation). Postcontrast magnetic resonance image of 20 patients showed dye leak at the EPJ proving EPJF as main cause of LDH. Our study provides the first in vivo evidence that LDH in humans is more commonly the result of EPJF than AF rupture and offers clinical validation of previous in vitro mechanical disruption studies. Future research must focus on the EPJ as a primary area of interest in LDH. N/A.

Initiation and progression of mechanical damage in the intervertebral disc under cyclic loading using continuum damage mechanics methodology: A finite element study

It is difficult to study the breakdown of disc tissue over several years of exposure to bending and lifting by experimental methods. There is also no finite element model that elucidates the failure mechanism due to repetitive loading of the lumbar motion segment. The aim of this study was to refine an already validated poro-elastic finite element model of lumbar motion segment to investigate the initiation and progression of mechanical damage in the disc under simple and complex cyclic loading conditions. Continuum damage mechanics methodology was incorporated into the finite element model to track the damage accumulation in the annulus in response to the repetitive loading. The analyses showed that the damage initiated at the posterior inner annulus adjacent to the endplates and propagated outwards towards its periphery under all loading conditions simulated. The damage accumulated preferentially in the posterior region of the annulus. The analyses also showed that the disc failure is unlikely to happen with repetitive bending in the absence of compressive load. Compressive cyclic loading with low peak load magnitude also did not create the failure of the disc. The finite element model results were consistent with the experimental and clinical observations in terms of the region of failure, magnitude of applied loads and the number of load cycles survived.

Numerical analysis of railway brake disc

A certain number of railway brake discs made of gray cast iron, showed the presence of small cracks only after a few thousand kilometers. To investigate main causes of a brake disc failure, numerical analysis was done by using ABAQUS software. Numerical analysis resulted from a physical model of heat flux in dependence of braking time. Physical model was applied considering all demands and presumptions given by industry representatives.

ISSLS Prize Winner: How Loading Rate Influences Disc Failure Mechanics

Mechanically induced disruption and subsequent microscopic investigation of lumbar intervertebral discs following a previously published testing protocol, but using a much higher rate of loading. To explore if loading rate affects the internal disruption mechanics of lumbar intervertebral discs. The failure mechanics of some bone-ligament-bone constructs vary with the rate of tensile load application. Like many ligaments, recent reports indicate that the mechanical response of the disc wall varies with strain-rate. It is possible that the internal failure mechanics of the disc wall also varies with strain-rate. Nuclear pressurization was used to deliver sudden pressure impulses directly to the nucleus of ovine lumbar motion segments. Pressure impulses were delivered to 12 neutrally positioned motion segments, and 15 motion segments held at 7° flexion. Aside from loading rate, testing was conducted in the same manner as 2 previously published studies that employed a gradual nuclear pressurization regime. Following testing, the internal damage resulting to each disc was analyzed using micro-CT and serial microscopy in tandem. Radial tears of the medioposterior disc wall were the most frequent cause of disc failure. In most cases, radial tears involved a combination of annular and endplate disruption: Neutrally positioned discs frequently suffered tears within the superior cartilaginous endplate adjacent to the transition zone and/or inner anulus. Flexed discs frequently suffered tears adjacent to the outer anulus at the cartilaginous/vertebral endplate junction, or within the vertebral endplate. Both groups frequently suffered endplate tears adjacent to the mid anulus at the inferior cartilaginous/vertebral endplate junction. The internal morphologies of the disc disruptions created in this study using high strain-rate impulse pressurization differed significantly from those documented previously for both neutrally positioned and flexed discs subjected to gradual low strain-rate pressurization. These morphologic differences show that the internal failure mechanics of lumbar intervertebral discs vary with the rate of internal radial load application.

Differential diagnosis of back pain in adult operated scoliosis patients

Back pain in adult operated scoliosis patients is a usually a major postoperative problem which has to be differentially diagnosed from a number of pathologies. The infection, immediate or delayed infection after elective spinal instrumentation and fusion is the principal postoperative problem for the patient and the surgeon. Surgical treatment is mandated in the majority of these cases, with the use of antibiotic treatment as well. Pseudarthrosis of the fusion is another major problem which needs surgical treatment as well. Some of the hardware problems that may occur are loosening, failure, inappropriate placement, prominence of hardware posteriorly or allergic reaction to it. Adjacent disc disease that is disc failure above or below fusion is a follow up problem appearing after some time postoperatively. Progression of curve after fusion can also happen and is connected to post op deterioration. Spinal balance problems, (trunk imbalance after fusion) create a serious disability to the patient. Flat back syndrome (mainly back pain after Harrington rod instrumentation for idiopathic scoliosis) also creates severe low back pain and disability. Thoracic (rib-cage) problems, rib pain after thoracoplasty and donor graft site pain (complications of iliac crest bone grafting in spine surgery) can appear postoperatively as well.

The influence of torsion on disc herniation when combined with flexion

The role of torsion in the mechanical derangement of intervertebral discs remains largely undefined. The current study sought to investigate if torsion, when applied in combination with flexion, affects the internal failure mechanics of the disc wall when exposed to high nuclear pressure. Thirty ovine lumbar motion segments were each positioned in 2 degrees axial rotation plus 7 degrees flexion. Whilst maintained in this posture, the nucleus of each segment was gradually injected with a viscous radio-opaque gel, via an injection screw placed longitudinally within the inferior vertebra, until failure occurred. Segments were then inspected using micro-CT and optical microscopy in tandem. Five motion segments failed to pressurize correctly. Of the remaining 25 successfully tested motion segments, 17 suffered vertebral endplate rupture and 8 suffered disc failure. Disc failure occurred in mature motion segments significantly more often than immature segments. The most common mode of disc failure was a central posterior radial tear involving a systematic annulus-endplate-annulus failure pattern. The endplate portion of these radial tears often propagated contralateral to the direction of applied axial rotation, and, at the lateral margin, only those fibres inclined in the direction of the applied torque were affected. Apart from the 2 degrees of applied axial rotation, the methods employed in this study replicated those used in a previously published study. Consequently, the different outcome obtained in this study can be directly attributed to the applied axial rotation. These inter-study differences show that when combined with flexion, torsion markedly reduces the nuclear pressure required to form clinically relevant radial tears that involve cartilaginous endplate failure. Conversely, torsion appears to increase the disc wall's resistance to radial tears that do not involve cartilaginous endplate failure, effectively halving the disc wall's overall risk of rupture.

The Morphology of Acute Disc Herniation

Hydrostatically induced disruption of flexed lumbar intervertebral discs followed by microstructural investigation. To investigate how flexion affects the anulus' ability to resist rupture during hydrostatic loading, and determine how the characteristics of the resulting disc failures compare with those observed clinically. While compression of neutrally positioned motion segments consistently causes vertebral failure, compression of flexed segments can induce herniation. Why flexion has this effect remains unclear. A vast range of herniation characteristics have been documented clinically; whether flexion-related herniations are likely to possess a subset of these is unknown. Forty-two ovine lumbar motion segments, dissected from the same 3 levels of 14 spines, were each flexed 7 degrees or 10 degrees from the neutral position. While maintained at one of these angles, the nucleus of each segment was gradually injected with a viscous radio-opaque gel via an injection screw placed longitudinally within the inferior vertebra, until failure occurred. Each segment was then inspected using microcomputed tomography and oblique illumination microscopy in tandem. RESULTS.: Eighteen segments suffered disc failure; 14 of these were caused by direct radial rupture of the anular wall. All radial ruptures were located in the central posterior anulus. Nine radial ruptures contained nuclear material, which had breached the posterior longitudinal ligament in 1 disc, and reached it in 5 others forming transligamentous and subligamentous nuclear extrusions, respectively. The most common radial rupture route, occurring in 10 discs, involved a systematic anulus-endplate-anulus failure pattern. Flexion places the anulus at risk by facilitating nuclear flow, limiting circumferential disruption while promoting radial rupture, and rendering the endplate/vertebra junction vulnerable to failure. Flexion may play a developmental role in those herniations possessing a central posterior radial rupture that incorporates a short span of endplate disruption along the apex of the vertebral rim.

Erratum to: Rock Dynamic Fracture Toughness Tested with Holed-Cracked Flattened Brazilian Discs Diametrically Impacted by SHPB and its Size Effect

Dynamic fracture initiation toughness of marble was tested using two types of the holed-cracked flattened Brazilian disc (HCFBD) specimens, which were diametrically impacted at the flat end of the disc by the split Hopkinson pressure bar (SHPB) of 100 mm diameter. One type of the discs is geometrically similar with different outside diameter of 42 mm, 80 mm, 122 mm and 155 mm respectively, and with crack length being half the diameter; another type of the discs has identical 80 mm diameter and different crack length. Issues associated with determination of the stress wave loading by the SHPB system and the crack initiation time in the disc specimen were resolved using strain gage technique. The stress waves recorded on the bars and the disc failure patterns are shown and explained. The tested dynamic fracture toughness increases obviously with increasing diameter for the geometrically similar HCFBD specimens. It changes moderately for the one-size specimens of identical diameter and different crack length. The size effect of rock dynamic fracture toughness is mainly caused by the fracture process zone length l and fracture incubation time τ, the latter being an additional influencing factor for the dynamic loading as compared with the counterpart static situation. Hence a method is proposed to determine a unique value for the dynamic fracture initiation toughness, the approach takes average of the local distribution and time history for dynamic stress intensity factor in the spatial-temporal domain, which is defined by l and τ jointly. In this way the dynamic size effect is minimized.

ISSLS Prize Winner: Microstructure and Mechanical Disruption of the Lumbar Disc Annulus

Mechanically induced annular disruption of lumbar intervertebral discs followed by microstructural investigation. To investigate the role that elevated nuclear pressures play in disrupting the lumbar intervertebral disc's annulus fibrosus. Compound mechanical loadings have been used to recreate clinically relevant annular disruptions in vitro. However, the role that individual loading parameters play in disrupting the lumbar disc's annulus remains unclear. The nuclei of ovine lumbar intervertebral discs were gradually pressurized by injecting a viscous radio-opaque gel via their inferior vertebrae. Pressurization was conducted until catastrophic failure of the disc occurred. Investigation of the resulting annular disruption was carried out using microcomputed tomography and differential interference contrast microscopy. Gel extrusion from the posterior annulus was the most common mode of disc failure. Unlike other aspects of the annular wall, the posterior region was unable to distribute hydrostatic pressures circumferentially. In each extrusion case, severe disruption of the posterior annulus occurred. Although intralamellar disruption occurred in the mid annulus, interlamellar disruption occurred in the outer posterior annulus. Radial ruptures between lamellae always occurred in the mid-axial plane. With respect to the annular wall, the posterior region is most susceptible to failure in the presence of high nuclear pressure, even when loaded in the neutral position. Weak interlamellar cohesion of the outer posterior lamellae may explain why the majority of herniations remain contained as protrusions within the outer annular wall.