Different Types Of Plastics Research Articles

Release of Microplastics from Reusable Kitchen Plasticware and Generation of Thermal Potential Toxic Degradation Products in the Oven

Plastics are one of the most important technical materials at present, yet they are associated with a whole series of environmental problems such as micro-and nanoplastics or their plasticizers, which have become increasingly relevant in recent years. While there are many studies that focus on microplastics (MPs) introduced into the human body through commercially produced food, there are nearly none that consider the MPs we ingest through homemade food made with plastic kitchen utensils such as mixing bowls. To investigate this, samples were obtained by exposing different plastic bowls made of acrylonitrile–butadiene–styrene (ABS), polypropylene (PP), melamine, polyethylene (PE), polystyrene (PS), and styrene–acrylonitrile (SAN), to mechanical stress and then analyzed via infrared spectroscopy. This not only raises the question of whether microplastics are incorporated into foods but also the extent to which the degradation products produced by thermal stress in an oven could play a toxicological role. Degradation products were generated by pyrolysis and analyzed afterwards using gas chromatography mass spectrometry. There were differences in the number of microplastic particles abraded by the different types of plastic, with the most consisting of melamine (898 particles) and the least consisting of low-density polyethylene (331 particles). There were also differences in the number and relevance of the thermal degradation products for the different plastics, so that a human toxicological assessment would have to be evaluated in further work.

Recent developments in microbial degradation of polypropylene: Integrated approaches towards a sustainable environment

Fossil-fuel-based plastics have many enticing properties, but their production has resulted in significant environmental issues that require immediate attention. Despite the fact that these polymers are manmade, some bacteria can degrade and metabolise them, suggesting that biotechnologies based on the principle of plastic biodegradation could be beneficial. Among different types of plastics, polypropylene (PP), either having low or high density, is one of the most consumed plastics (18.85%). Their debasement under natural conditions is somewhat tricky. Still, their debasement under natural conditions is rather difficult slightly. However, different scientists have still made efforts by employing other microbes such as bacteria, fungi, and guts bacteria of larvae of insects to bio-deteriorate the PP plastic. Pre-irradiation techniques (ultraviolet and gamma irradiations), compatibilizers, and bio-additives (natural fibers, starch, and polylactic acid) have been found to impact percent bio-deterioration of different PP derivatives stronglythe various. The fungal and bacterial study showed that PP macro/microplastic might serve as an energy source and sole carbon during bio-degradation. Generally, gravimetric method or physical characterization techniques such as FTIR, XRD, SEM, etc., are utilized to affirm the bio-degradation of PP plastics-based materials. However, these techniques are not enough to warrant the bio-deterioration of PP. In this regard, a new technique approach that measures the amount of carbon dioxide emitted during bacterial or fungus degradation has also been discussed. In addition, further exploration is needed on novel isolates from plastisphere environments, sub-atomic strategies to describe plastic-debasing microorganisms and improve enzymatic action strategies, and omics-based innovations to speed up plastic waste bio-deterioration.

Translocation of Phthalates From Food Packaging Materials Into Minced Beef.

There has been increased concern regarding the potential human health risks associated with exposure to phthalates. Research indicates that food intake is the most critical exposure pathway for phthalates. This study aimed to investigate packaged beef samples for the presence of dimethyl terephthalate (DMTP), di-n-butyl phthalate (DnBP), and diisooctyl phthalate (DiOP) and to assess their translocation from the common form of food packaging procured from various Saint-Petersburg and Leningrad region shops. The packaging samples include paper and different types of plastic. Phthalates were extracted by dichloromethane and analyzed by gas chromatography coupled with mass spectrometry (GC-MS). While DnBP had the highest mean values in beef from 34.5 to 378.5 μg·kg−1, DiOP displayed the lowest mean values from LOD to 37 μg·kg−1. The larger contact area and the presence of distributed fat on the surface of the minced meat resulted in significantly higher phthalate translocation than beef slices. Further, DMTP was not detected in any samples. However, the examined food packages do not meet the requirements of Russian, EU and USA legislation, as DnBP migrates to meat. Calculated maximum DnBP daily intake of 0.167 μg·kg−1·day−1 for chilled minced beef in vacuum packaging did not exceed tolerable daily intake (TDI) level. The most alarming results are concerning the phthalates presence in beef farmed in the Leningrad region and not subjected to any plastic packaging. A full-scale study is warranted to determine the pathways and sources of phthalates migration in the food chain.

Specific Plasticity Loci and Their Synergism Mediate Operant Conditioning.

Despite numerous studies examining the mechanisms of operant conditioning (OC), the diversity of OC plasticity loci and their synergism have not been examined sufficiently. In the well-characterized feeding neural circuit of Aplysia, in vivo and in vitro appetitive OC increases neuronal excitability and electrical coupling among several neurons leading to an increase in expression of ingestive behavior. Here, we used the in vitro analog of OC to investigate whether OC reduces the excitability of a neuron, B4, whose inhibitory connections decrease expression of ingestive behavior. We found OC decreased the excitability of B4. This change appeared intrinsic to B4 because it could be replicated with an analog of OC in isolated cultures of B4 neurons. In addition to changes in B4 excitability, OC decreased the strength of B4's inhibitory connection to a key decision-making neuron, B51. The OC-induced changes were specific without affecting the excitability of another neuron critical for feeding behavior, B8, or the B4-to-B8 inhibitory connection. A conductance-based circuit model indicated that reducing the B4-to-B51 synapse, or increasing B51 excitability, mediated the OC phenotype more effectively than did decreasing B4 excitability. We combined these modifications to examine whether they could act synergistically. Combinations including B51 synergistically enhanced feeding. Taken together, these results suggest modifications of diverse loci work synergistically to mediate OC and that some neurons are well suited to work synergistically with plasticity in other loci.SIGNIFICANCE STATEMENT The ways in which synergism of diverse plasticity loci mediate the change in motor patterns in operant conditioning (OC) are poorly understood. Here, we found that OC was in part mediated by decreasing the intrinsic excitability of a critical neuron of Aplysia feeding behavior, and specifically reducing the strength of one of its inhibitory connections that targets a key decision-making neuron. A conductance-based computational model indicated that the known plasticity loci showed a surprising level of synergism to mediate the behavioral changes associated with OC. These results highlight the importance of understanding the diversity, specificity and synergy among different types of plasticity that encode memory. Also, because OC in Aplysia is mediated by dopamine (DA), the present study provides insights into specific and synergistic mechanisms of DA-mediated reinforcement of behaviors.

Conversion of plastic waste into fuel oil using zeolite catalysts in a bench-scale pyrolysis reactor.

Catalytic pyrolysis of mixed plastic waste to fuel oil experiment was tested with ZSM-5 zeolite (commercial and synthesized) catalysts along with other catalysts. The ZSM-5 zeolite catalyst was effectively produced using a hydrothermal technique via metakaolin as an alumina source. The catalytic pyrolysis of different types of plastic (single and multilayer) wastes in the presence of various catalysts was tested with a bench-scale pyrolysis setup with 2 kg per batch capacity. Polyolefin based plastics (low-density polyethylene, high-density polyethylene, and polypropylene), multilayer plastics such as biaxial oriented polypropylene (BOPP), metalized biaxial oriented polypropylene layers (MET BOPP), polyethylene terephthalate (PET), metalized polyethylene terephthalate (MET/PET), polyethylene terephthalate combined polyethylene (PET/PE), and mixed plastic waste collected from the corporation sorting center were pyrolyzed in a batch pyrolysis system with 1 kg feed to determine the oil, gas and char distributions. The performances of commercial ZSM-5 and lab synthesized ZSM-5 catalysts were compared for the pyrolysis of non-recyclable plastic wastes. Other commercial catalysts including mordenite and gamma alumina were also tested for pyrolysis experiments. The gross calorific value of oil obtained from different combinations of multilayer packaging waste varied between 10 789–7156 kcal kg−1. BOPP-based plastic waste gave higher oil yield and calorific value than PET-based plastic waste. Sulfur content present in the oil from different plastic wastes was measured below the detection limit. The synthesized ZSM-5 zeolite catalyst produced a maximum oil output of 70% and corresponding gas and char of 16% and 14% for LDPE plastic. The strong acidic properties and microporous crystalline structure of the synthesized ZSM-5 catalyst enables increased cracking and isomerization, leading to an increased breakup of larger molecules to smaller molecules forming more oil yield in the pyrolysis experiments. Residual char analysis showed the maximum percentage of carbon with heavy metal concentrations (mg kg−1) in the range of viz., chromium (15.36–97.48), aluminium (1.03–2.54), cobalt (1.0–5.85), copper (115.37–213.59), lead (89.12–217.3), and nickel (21.05–175.41), respectively.

Deodorization of post-consumer plastic waste fractions: A comparison of different washing media

An important impediment to the acceptance of recyclates into a broader market is their unwanted odor after reprocessing. Different types of washing procedures are already in place, but fundamental insights into the deodorization efficiencies of different washing media are still relatively scarce. Therefore, in this study, the deodorization efficiencies of different types of plastics after washing with different media were determined via gas chromatography and mass spectrometry analysis. A total of 169 compounds subdivided into various chemical classes, such as alkanes, terpenes, and oxygenated compounds, were detected across all packaging types. Around 60 compounds were detected on plastic bottles, and around 40 were detected on trays and films. Owing to the differences in physicochemical properties of odor compounds, different deodorization efficiencies were obtained with different washing media. Water and caustic soda were significantly more efficient for poly(ethylene terephthalate) bottles with deodorization efficiencies up to 80%, whereas for polyethylene (PE) and polypropylene bottles, the washing media were relatively inefficient (around 30–40%). Adding a detergent or an organic solvent could increase deodorization efficiencies by up to 70–90% for these packaging types. A similar trend was observed for PE films having deodorization efficiencies in the range of 40–50% when washing with water or caustic soda and around 70–80% when a detergent was added. Polystyrene trays were most effectively deodorized with a detergent, achieving efficiencies up to 67%. Hence, this study shows that optimal washing processes should be tailored to specific packaging types to further improve deodorization and to eventually be able to meet ambitious European recycling targets.

Effect of biofilm formation on different types of plastic shopping bags: Structural and physicochemical properties

Plastics and biofilms have a complicated relationship that has great interest. Bacterial cell attachment and biofilm formation is considered to cause health and environmental risks from plastic waste accumulation. In water, plastic waste could serve as a new substrate for bacteria. In our study, the attachment of Escherichia coli K12, to four types of plastic shopping bags (biodegradable polylactic acid and the non-biodegradable polypropylene, polyethylene and polyvinyl chloride) was investigated. The change in physicochemical phenomena of each plastic, such as reduced hydrophobicity and higher exopolysaccharide concentrations (total extractable protein and carbohydrate) resulted in increased biofilm content on the plastic surfaces. The bacterial colonization of different plastic surfaces controls the ionic strength of the nutrition sources. The adhesion of Escherichia coli K12 cells on the surfaces were revealed by SEM images. The finding shows that increases surface roughness, besides favor for adhesion of bacterial cells due to hydrophobicity leading to a rapid attachment of Escherichia coli K12 on the surfaces. In addition, we used Derjaguin-Landau-Verwey-Overbeek theory to predict the attachment of Escherichia coli K12, which gave result of adhesion due to the high energy barrier. This present study added to our knowledge of the possible consequences of plastics acting as a new habitat for microbes in different aquatic condition.

Plastic pollution: why is it a public health problem?

Plastic pollution: why is it a public health problem?

Screening and Optimization of Microalgae Biomass and Plastic Material Coprocessing by Hydrothermal Liquefaction

In the past decade, microalgae biomass has been attracting considerable interest in valuable biocomponents and biofuel production. Meanwhile, plastic waste handling has become one of the most pressing global environmental concerns. Coprocessing of plastic waste and biomass has previously been reported to produce good quality fuel oil and high-value chemicals. In this study, we examined a coliquefaction process (co-HTL) of 2 microalgae, Chlorella vulgaris (Cv) and Nannochloropsis gaditana (Ng), with nine types of common plastics. In a first step, the co-HTL process was conducted in microautoclave reactors with a fixed algae/plastic mass ratio (50:50) at a temperature of 350 °C and a pressure of 16 MPa for a holding time of 15 min. Among the different types of plastics, positive synergistic effects between polycarbonate (PC), polystyrene (PS), and microalgae have been observed: (1) Plastics showed greater decomposition. (2) HTL crude oil yields were increased. Ng algae exhibits a higher interaction ability with plastics. Then, PC and PS were coprocessed with Ng algae using the response surface methodology to optimize the effects of temperature (300–400 °C), algae/plastic mass ratio (20:80–80:20), and holding time (5–45 min) on HTL crude oil yield. Software-based data analysis of the co-HTL experiments were conducted, and the optimal parameters were proposed, which were verified by the experiment results; Ng+PC (20:80 wt %) exhibits the highest crude oil yield of 67.2% at 300 °C with a 5 min holding time, while Ng+PS (80:20 wt %) generates 51.4 wt % crude oil yield at 400 °C and a 25 min holding time. Finally, the analytical results of elemental analysis, FTIR, 1H NMR, GPC, GC-MS, and TGA on the crude oil produced from pure microalgae HTL and co-HTL were compared, indicating that Ng+PC crude oil is more suitable for aromatic chemicals production and Ng+PS crude oil could be more favorable for biofuel applications.

Biodegradation of Different Types of Plastics by Tenebrio molitor Insect.

Looking for new, sustainable ways to utilize plastics is still a very pertinent topic considering the amount of plastics produced in the world. One of the newest and intriguing possibility is the use of insects in biodegradation of plastics, which can be named entomoremediation. The aim of this work was to demonstrate the ability of the insect Tenebrio molitor to biodegrade different, real plastic waste. The types of plastic waste used were: remains of thermal building insulation polystyrene foam (PS), two types of polyurethane (kitchen sponge as PU1 and commercial thermal insulation foam as PU2), and polyethylene foam (PE), which has been used as packaging material. After 58 days, the efficiency of mass reduction for all of the investigated plastics was 46.5%, 41.0%, 53.2%, and 69.7% for PS, PU1, PU2, and PE, respectively (with a dose of 0.0052 g of each plastic per 1 mealworm larvae). Both larvae and imago were active plastic eaters. However, in order to shorten the duration of the experiment and increase the specific consumption rate, the two forms of the insect should not be combined together in one container.

Knowledge and perception of different plastic bags and packages: A case study in Brazil

The growing demand for plastics, for packaging and consumption, is a current environmental issue. Although there are many scientific developments concerning material science, knowledge about the public's perception is low, which can delay society's efforts to face this challenge. This study aimed to understand if Brazilians who practice different sustainable actions perceive differently biodegradable, recycled, and common plastics and have different purchase intentions for each specific type of packaging. A total of 1080 Brazilian adults were first classified by their day-to-day attitudes regarding sustainability efforts. Then, their purchase intention and perception about different plastics were assessed. Regardless of sustainability practices, people associate common plastic bags with negative attributes and biodegradable plastic bags with positive attributes. This shows that there is a well-established concept about these types of bags, even if there are some misconceptions (e.g. recyclable) or controversies (e.g. non-polluting). On the other hand, results showed that consumers who adopted more sustainable practices were 3.5 times more willing to pay for biodegradable packages, even though no differences were observed in the accepted price for biodegradable bags between consumer's groups. Finally, the purchase intention comparisons for products packaged in recycled and biodegradable plastics showed the consumers were more interested in those biodegradable plastics and the purchase intention was lower for perishable food (e.g. products that can have higher safety risks). The results are important for understanding environmental policy management in Brazil, highlighting the importance to improve the population's knowledge about different types of plastic, leading to more conscious choices.

Brain Plasticity in Humans and Model Systems: Advances, Challenges, and Future Directions.

Plasticity, and in particular, neurogenesis, is a promising target to treat and prevent a wide variety of diseases (e.g., epilepsy, stroke, dementia). There are different types of plasticity, which vary with age, brain region, and species. These observations stress the importance of defining plasticity along temporal and spatial dimensions. We review recent studies focused on brain plasticity across the lifespan and in different species. One main theme to emerge from this work is that plasticity declines with age but that we have yet to map these different forms of plasticity across species. As part of this effort, we discuss our recent progress aimed to identify corresponding ages across species, and how this information can be used to map temporal variation in plasticity from model systems to humans.

Unravelling the attributes of novel cyanobacteria Jacksonvillea sp. ISTCYN1 by draft genome sequencing

Filamentous cyanobacteria, Jacksonvillea sp. ISTCYN1 was isolated from agriculture field and cultured in BG-11 medium. This study, report the genome sequence of cyanobacteria Jacksonvillea thatto the best of our knowledgeis the firstgenome sequenceof thisgenus. The 5.7 MB draft genome sequence of this cyanobacterium contains 5134 protein-coding genes. The phylogenetic tree was constructed based on genome and Desertifilum sp. IPPAS B-1220 validated the closest relationship with Jacksonvillea sp. ISTCYN1. The growth of strain ISTCYN1 has been reported in the presence of different types of plastic when used as a sole carbon source. SEM analysis revealed biofilm formation by cyanobacterial strain ISTCYN1 on the surface of high and low-density polyethylene and polypropylene. In the presence of these plastics, EPS production has also been reported by this strain. Whole genome sequence analysis reveals the presence of many genes involved in biofilm formation. The presence of key enzymes responsible for plastic degradation laccase, esterase, lipase, thioesterase, and peroxidase have been predicted in the genome analysis. Genome analysis also provides insight into the genes involved in biotin biosynthetic pathways. Furthermore, the presence of many selenoproteins reveals the selenium acquisition by this cyanobacterium.

(Not) Doing the Right Things for the Wrong Reasons: An Investigation of Consumer Attitudes, Perceptions, and Willingness to Pay for Bio-Based Plastics

Fossil-based plastics are significant contributors to global warming through CO2 emissions. For more sustainable alternatives to be successful, it is important to ensure that consumers become aware of the benefits of innovations such as bio-based plastics, in order to create demand and a willingness to initially pay more. Given that consumer attitudes and (inaccurate) beliefs can influence the uptake of such new technologies, we investigated participants’ attitudes towards fossil-based and bio-based plastic, their perceived importance of recycling both types of plastic, their willingness to pay, and their perceptions of bio-based plastic in four studies (total N = 961). The pre-registered fourth study experimentally manipulated information about bio-based plastic and measured willingness to pay for different types of plastic. The results suggest participants hold very favourable attitudes and are willing to pay more for bio-based products. However, they also harbour misconceptions, especially overestimating bio-based plastic’s biodegradability, and they find it less important to recycle bio-based than fossil-based plastic. Study 4 provided evidence that educating consumers about the properties of bio-based plastic can dispel misconceptions and retain a favourable attitude and a high willingness to pay. We found mixed evidence for the effect of attitudes on willingness to pay, suggesting other psychological factors may also play a role. We discuss how attitudes and misconceptions affect the uptake of new sustainable technologies such as bio-based plastics and consumers’ willingness to purchase them.

Characterization of Pyrolytic Oil Produced from Waste Plastic in Quezon City, Philippines Using Non-catalytic Pyrolysis Method

Due to massive amount of waste plastics in different dumpsites, our community suffers and also the environment. Thus, affects nearby people with problems with plastic wastes. One of the processes to lessen these wastes is through pyrolysis of which fuel oil can be produced. The study involved the production of fuel oil from waste plastics taken from the Payatas dump site in Quezon City, Philippines. After thorough cleaning, the waste plastics were shredded thru mechanical means and underwent pyrolysis. Given the available thermal chamber facility in ITDI-DOST in Taguig City, Philippines, pyrolysis of waste plastics produced fuel oil in varying per cent yield from the different types of plastic. Characterization of the oil sample was conducted such as ash content, carbon residue, copper corrosion strip, flash point, pour point, sulfur, kinematic viscosity, specific gravity water and sediments that were based from the PNS/DOE QS 006-2005. The oil sample was analyzed using different laboratory tests following the methods of the American Society for Testing and Materials (ASTM). Using this standards, the analysis of the oil sample gave the positive results in comparison to the specifications set by the Philippine National Standard and was classified as fuel oil. Pyrolytic oil from waste plastic can be an alternative fuel source.

3D Printing Technology and its Significant Applications in the Context of Healthcare Education

3D printing applications help solve challenges in the field of healthcare. These technologies evolved to produce custom-made medical devices and implants for patients and enhance medical education and research. This paper aims to make readers aware of the role of 3D printing in the field of medical education. 3D printing technologies are part of additive manufacturing (AM) technologies. 3D printing shows excellent potential with unconventional materials like different types of plastic, ketones, wood, human cells, metal powder, ceramics, composites, smart material, etc. This manufacturing method is suitable for producing complex and intricate shaped medical objects of the required property with lesser wastage of material. This paper introduces 3D printing technology and the need to carry out this study related to medical education and research. A brief literature review of 3D printing has been carried out. The paper further discusses the capabilities of 3D printing in the field of medicine. Patient-specific 3D models are being designed and then manufactured and implanted. 3D models of defective body parts help surgical planning and better part designing. Finally, the paper discusses significant roles of 3D printing in healthcare education in a tabular form. For the future, this technology has immense potential for medical education, surgical planning and support including for a clear understanding of the disease.

Using of system SurveNIR for identification of plastics in library collection

The paper describes qualitative methods of modern library collections (produced after the year 1800) survey in The National Library of the Czech Republic in Prague. Each book is primarily composed of paper sheets and bookbinding. In modern library collections bookbinding usually contains parts composed of synthetic materials. Different types of materials have different mechanisms of degradation. Therefore, the main objectives of this work are nondestructive identification of synthetic materials in bookbinding, their degradation processes, and methods of conservation, conditions of storage, and preventive care as well. Based on the preliminary results of the collection survey in the National Library of the Czech Republic, the most usual types of synthetic materials in bookbinding are cellulose nitrate, cellulose acetate, polyethylene, polyurethane, polymethylmethacrylate, and polyvinyl chloride, both of solid and plasticized type. For faster survey of the collections and deeper information is used new instruments for modern library collection survey and preservation – SurveNIR measuring system. SurveNIR measuring system is used for determination of paper properties and identification of plastic materials using chemometric and comparison with material standards. It can identify more than 45 different types of plastics. It is a nondestructive method, very fast, and it is possible to obtain results in a few seconds of measuring. The SurveNIR system was developed in the European project.

Label-free identification and differentiation of different microplastics using phasor analysis of fluorescence lifetime imaging microscopy (FLIM)-generated data

As plastic pollution is becoming an increasing worldwide problem, a variety of different techniques for the detection and in-depth characterization of plastics, including spectroscopy and chromatography methods, were introduced to the public. Recently we presented fluorescence lifetime imaging microscopy (FLIM) a new approach for the identification and characterization of microplastics using their fluorescence lifetime (τ) for differentiation. A very powerful extension of the recently established FLIM could be phasor analysis, which allows data representation in an interactive 2D graphical phasor plot thereby enabling a global view of the fluorescence decay in each pixel of the measured image. Microplastic particles generated from six different types of plastics were subjected to excitation wavelengths of 440 nm, upon which specific fluorescence lifetimes as well as the photon yield were determined using FLIM and phasor analysis. We could show that phasor analysis for FLIM with a laser pulse repetition frequency of 40 MHz was able to generate specific locations in the phasor plot for the plastics for fast differentiation, e.g. resulting in well-defined phasor plot positions for ABS at 3.019 ns, PPE at 6.239 ns, PET bottle from Germany at 2.703 ns and PET bottle from USA at 2.711 ns. Phasor analysis for FLIM proves to be a fast, label-free, and sensitive method for the identification and differentiation of plastics also with the aid of visualization variation enabling techniques such as heat treatment of plastics.

Use of Digital Olfaction to Standardize Cabin Odor Testing in Automotive Interiors

<div class="section abstract"><div class="htmlview paragraph">Subjectivity in testing for automotive validation processes is typically a sticking point for many suppliers and OEMs. For vehicle interiors, in addition to the laboratory testing, human panels of “trained noses” are used to judge the different components and the completed vehicle.</div><div class="htmlview paragraph">In the automotive industry, there is no standardization as each OEM has their own testing specifications, rating scale and methods. In addition to the variation in OEM specification, there are also global specifications issued by SAE, VDA, and ISO. This lack of unified quantitative norms leads to increased costs and timing for suppliers, lab-to-lab variations in results and ultimately longer development times for the OEMs.</div><div class="htmlview paragraph">With the advances in sensors, biochemistry and machine learning, odor detection and classification can be achieved with the use of a digital olfaction device, or “electronic nose”. We will demonstrate the ability to identify different types of plastics, the ability to differentiate between compound variants of the same material and a proof of concept for detection of odors in the automotive domain based on the ISO 12219-7 and VDA270 standards. We will also propose a quantifiable rating of odor which mimics the human panel established norms, in a way which is reproducible and independent of variation between individual testers. Ultimately, standardization of odor testing with consistent, repeatable and cost-effective digital olfaction methods can bring traceability and credibility to Tier 1 suppliers that translate to end-product quality for OEMs.</div></div>

АВТОМАТИЗОВАНИЙ МОДУЛЬ СОРТУВАННЯ ПЛАСТИКОВИХ ВІДХОДІВ

Sorting of solid waste is now of paramount importance. Therefore, it is advisable today to spend more time developing new modern, efficient, environmentally friendly waste sorting systems in an automated mode. The development of modern technologies for sorting solid waste is becoming increasingly important, as classical methods of disposal are no longer able to meet the needs of mankind in this regard. An important aspect is both the sorting of waste with the possibility of further processing and the disposal process itself without significant harm to the environment. Currently, there is a significant number of methods and organizational procedures for sorting solid waste, each of which has its advantages and disadvantages. An important element of solid waste sorting technologies should be the ability to quickly identify types of materials with their subsequent separation and disposal, which will significantly increase the productivity of this process. The purpose of the article is to improve the method of sorting solid waste on the basis of visual spectrometry. On the example of a specific type of solid waste, namely plastic, the capabilities of the proposed module for sorting plastics based on visual spectrometry are demonstrated. The paper also considers the main properties of spectroscopy in the field of infrared spectrum in order to develop a technology for identifying different types of plastics during their sorting for further processing or disposal. The method of solid waste sorting on the basis of visual spectrometry was proposed in the work, which allowed to obtain the optimal technological process of identification and separation of different types of plastics. The prototype of the module for sorting of plastics is developed, the basic principles of its functioning are considered.