Deposition Rate Research Articles

Physics of microscale freeform 3D printing of ice

Ice is emerging as a promising sacrificial material in the rapidly expanding area of advanced manufacturing for creating precise 3D internal geometries. Freeform 3D printing of ice (3D-ICE) can produce microscale ice structures with smooth walls, hierarchical transitions, and curved and overhang features. However, controlling 3D-ICE is challenging due to an incomplete understanding of its complex physics involving heat transfer, fluid dynamics, and phase changes. This work aims to advance our understanding of 3D-ICE physics by combining numerical modeling and experimentation. We developed a 2D thermo-fluidic model to analyze the transition from layered to continuous printing and a 3D thermo-fluidic model for the oblique deposition, which enables curved and overhang geometries. Experiments are conducted and compared with model simulations. We found that high droplet deposition rates enable the continuous deposition mode with a sustained liquid cap on top of the ice, facilitating smooth geometries. The diameter of ice structures is controlled by the droplet deposition frequency. Oblique deposition causes unidirectional spillover of the liquid cap and asymmetric heat transfer at the freeze front, rotating the freeze front. These results provide valuable insights for reproducible 3D-ICE printing that could be applied across various fields, including tissue engineering, microfluidics, and soft robotics.

Influence of agricultural activity in corn farming on airborne microplastic in surrounding elementary school

Microplastics (MPs) have been widely detected in agricultural soils, and agricultural activities have been identified as an important factor influencing the abundance of MPs in the air. However, no studies have investigated whether agricultural activities are contributors to airborne MPs in buildings near farms. We collected airborne MP samples using an active sampling method from an elementary school near corn farms during different cultivation stages to assess the impact of agricultural activities on MPs in the study school near farms. Our data showed that the predominant shapes, sizes, colors, and polymer compositions were fragments, 2–50 μm, black or grey, and polyethylene terephthalate, respectively, during all cultivation stages. The highest and lowest MP concentrations were recorded during the land preparation (56.8 ± 7.4 particles/m3, August 2022) and growth (2.5 ± 1.8 particles/m3, February 2022) stages, respectively. A multiple-path particle dosimetry model revealed that the deposition fractions of MPs in humans were highest in the head; the highest and lowest deposition rates and fluxes of MPs in the airway were found during the land preparation and growth stages, respectively. The concentration of MPs did not present a positive correlation with potassium or crustal elemental concentration; however, it did show a positive association with temperature value. Therefore, our data did not show that corn cultivation influences MP concentrations in the study school near corn farms; instead, temperature was an important influencing factor.

Multilayer Diamond‐Like Carbon Films on Monocrystalline Diamond

Multilayer films of diamond‐like carbon (DLC) on monocrystalline diamond substrates have been for the first time obtained by plasma‐chemical deposition. Their chemical composition and structural and morphological properties are studied. The DLC individual layers differ in their sp3 carbon content. The multilayer nature of the resulting coatings is confirmed by periodic density modulation on the small‐angle X‐ray reflectometry curve and modulations in the CsC8, CsC6, CsC4 lines on the crater depth profile of secondary ions of elements (secondary ion mass spectrometry). The dependence of the deposition rate of multilayer DLC films on diamond, their composition and properties on the argon additive to the reaction gas mixture, as well as on methane flow, pressure and growth time, are studied.

A new look at an explanation of band gap of PECVD grown a-Si:H thin films using absorption spectra, spectroscopic ellipsometry, Raman, and FTIR spectrosopy

Amorphous silicon is seen to be among the most promising materials for solar cell applications because of its higher temperature coefficient of resistance, adjustable forbidden-band gap, enhanced optical absorption, and capacity to reduce solar module costs. Changes in deposition rate, absorption coefficient and optical band gap of a-Si:H films with varying silane flow rate show that SiH4 molecules density influence the plasma growth process. Silane flow rate affects the percentage of silicon atoms during processing. The deposition rate of a-Si: H films increased from 14.36 nm/min to 15.97 nm/min by increasing silane flow rate from 25 sccm to 45 sccm. Broadening of optical band is observed. Films deposited at 35 sccm of silane flow rate shows the higher absorption coefficient. All films are characterized by FTIR, Raman spectroscopy, spectroscopic ellipsometry and optical absorption to understand the changes in band gap. The band gap Eg of all films is correlated with microstructure factor, Q factor, bond angle deviation Δθ and width of Si–H2 mode to analyse the effect of defects, disorders and microvoids.

Evolution of Material Properties and Residual Stress with Increasing Number of Passes in Aluminium Structure Printed via Additive Friction Stir Deposition.

Additive friction stir deposition (AFSD) is an emerging solid-state additive manufacturing process with a high deposition rate. Being a non-fusion additive manufacturing (AM) process, it significantly eliminates problems related to melting such as cracking or high residual stresses. Therefore, it is possible to process reactive materials or high-strength alloys with high susceptibility to cracking. Although the residual stresses are lower in this process than with the other AM processes, depending on the deposition path, geometry, and boundary conditions, residual stresses may lead to undesired deformations and deteriorate the dimensional accuracy. Thermal cycling during layer deposition, which also depends on the geometry of the manufactured component, is expected to affect mechanical properties. To this day, the influence of the deposit geometry on the residual stresses and mechanical properties is not well understood, which presents a barrier for industry uptake of this process for large-scale part manufacturing. In this study, a stepped structure with 4, 7, and 10 passes manufactured via AFSD is used to investigate changes in microstructure, residual stress, and mechanical property as a function of the number of passes. The microstructure and defects are assessed using scanning electron microscopy and electron backscatter diffraction. Hardness maps for each step are created. The residual stress distributions at the centreline of each step are acquired via non-destructive neutron diffraction. The valuable insights presented here are essential for the successful utilisation of AFSD in industrial applications.

The growth rate of senile plaques is determined by the competition between the rate of deposition of free Aβ aggregates into plaques and the autocatalytic production of free Aβ aggregates

The formation of amyloid beta (Aβ) deposits (senile plaques) is one of the hallmarks of Alzheimer’s disease (AD). This study investigates what processes are primarily responsible for their formation. A model is developed to simulate the diffusion of amyloid beta (Aβ) monomers, the production of free Aβ aggregates through nucleation and autocatalytic processes, and the deposition of these aggregates into senile plaques. The model suggests that efficient degradation of Aβ monomers alone may suffice to prevent the growth of senile plaques, even without degrading Aβ aggregates and existing plaques. This is because the degradation of Aβ monomers interrupts the supply of reactants needed for plaque formation. The impact of Aβ monomer diffusivity is demonstrated to be small, enabling the application of the lumped capacitance approximation and the derivation of approximate analytical solutions for limiting cases with both small and large rates of Aβ aggregate deposition into plaques. It is found that the rate of plaque growth is governed by two competing processes. One is the deposition rate of free Aβ aggregates into senile plaques. If this rate is small, the plaque grows slowly. However, if the rate of deposition of Aβ aggregates into senile plaques is very large, the free Aβ aggregates are removed from the intracellular fluid by deposition into the plaques, leaving insufficient free Aβ aggregates to catalyze the production of new aggregates. This suggests that under certain conditions, Aβ plaques may offer neuroprotection and impede their own growth. Additionally, it indicates that there exists an optimal rate of deposition of free Aβ aggregates into the plaques, at which the plaques attain their maximum size.

Effect of Hydrophobic Dust Particles on the Evaporation Rate from Water Surface

In the paper, the effect of natural dust deposited from the air on the evaporation rate from the water surface is experimentally investigated. Experiments were conducted for stationary liquid without wind blowing across the surface and with mild wind that does not deform the surface, at a constant rate of particle deposition. It is shown that the evaporation rate is a linear function of the difference in the saturated vapor pressure at the water surface and the partial pressure of the air mixture at the temperature and relative humidity in the laboratory at the beginning of the deposition process, when the proportion of the surface covered with dust is small. With the increase in deposition time, hydrophobic particles gather into conglomerates, reducing the proportion of the exposed surface and the evaporation rate.

Unveiling the microstructure and promising electrochemical performance of heavily phosphorus-doped diamond electrodes

The challenge of doping synthetic diamond with phosphorus stems from the atomic size mismatch between phosphorus and carbon atoms, which previously hindered achieving high phosphorus doping levels. This limitation delayed the exploration of phosphorus-doped diamond (PDD) in electrochemical applications, where it holds potential as a novel and appealing electrode material because PDD uniquely combines diamond's exceptional properties with phosphorus atoms inducing n-type conductivity. In this study, heavily doped PDD electrodes were successfully developed using chemical vapour deposition, followed by comprehensive microstructural and electrochemical characterisations. The influence of phosphorus doping, manipulated via high phosphine gas concentration or time-dependant precursor gas flow control, on the PDD properties was thoroughly examined. PDD layers grown at higher phosphine concentrations demonstrated enhanced phosphorus incorporation, leading to a higher prevalence of fine nano-crystalline diamond grains and non-diamond carbon components, while also slowing the growth rate. Notably, a distinct PDD sample produced under dynamic gas flow with lower phosphine concentration revealed larger grain sizes, increased effective deposition rate, and improved phosphorus levels compared to its counterpart synthesized under static conditions. Cyclic voltammetry in a 1 mol L−1 KCl solution revealed a low double-layer capacitance (<11 µF cm−2) in all as-grown PDD electrodes. However, significant differences between the samples emerged during the experiments conducted with redox probes [Ru(NH3)6]3+/2+ and [Fe(CN)6]3−/4−. Particularly, higher phosphorus content promoted well-developed voltammograms, significantly reduced peak-to-peak separation values, faster electron transfer rates, and increased peak currents. Furthermore, the possibility of using heavily P-doped diamond electrodes for the detection of two organic analytes, dopamine and ascorbic acid, was successfully manifested. All in all, the as-grown, highly P-doped diamond electrodes proved their ability, first time ever, to record well-defined signals of both inorganic redox probes and complex organic compounds, unravelling their potential in electroanalysis and sensor development and broadening the scope of PDD utilisation.

Identification and Derivation of Emerging Contaminants in the Roof Rainwater Confluence

To identify emerging contaminants （ECs） in rainwater is a topic that has gradually received widespread attention. Rainwater resources, specifically urban roofs, play a crucial role in utilizing rainwater efficiently by understanding the occurrence and migration characteristics of pollutants in precipitation. This study selected a typical roof and studied the differences in rainwater quality and pollution occurrence at different collection stages during six rainfall events from March to May in 2023. Principal component analysis （PCA） and correlation analysis were used to explore the distribution, migration, and transformation of ECs in the collection process of roof rainwater. The findings revealed the presence of 44/54 ECs in wet deposition, dry and wet deposition, and roof runoff processes, with a total concentration range of 63.0 to 432.4 ng·L-1 and an average concentration of 166.8 ng·L-1. Notably, bisphenol A （BPA） exhibited the highest concentration, ranging from 14.7 to 265.6 ng·L-1, with an average concentration of 62.5 ng·L-1, followed by ofloxacin （OFX） and ethylhexyl methoxycinnamate （EHMC）, with detected concentrations up to 45.5 ng·L-1 and 44.8 ng·L-1. Dissolved organic matter （DOM）, nitrogen pollutants, and particulate matter were important factors affecting the occurrence characteristics of ECs, with a mantel correlation coefficient of up to 0.98 （P<0.01）. Based on the analysis of different rainfall events and collection stages, variations were observed in the accumulation pathways and contribution ratios of different pollutants. The wet deposition exhibited the highest content of ECs in the initial stage, whereas the dry and wet deposition and roof runoff processes displayed higher ECs content in the later stages. Additionally, the average ECs contribution rates of dry and wet deposition to roof runoff were 21.48% and 78.52%, respectively. Due to the influence of roof material and surface roughness retention performance, over 30% of ECs, including pharmaceuticals and personal care products （PPCPs）, endocrine-disrupting compounds （EDCs）, and pesticides, were deposited on the roof during the runoff collection. The results of this research can provide the theoretical foundation and technical support for the identification and control of ECs in urban roof runoff and for the safe storage of rainwater.

Acoustic Signal-Based Defect Identification for Directed Energy Deposition-Arc Using Wavelet Time-Frequency Diagrams.

Several advantages of directed energy deposition-arc (DED-arc) have garnered considerable research attention including high deposition rates and low costs. However, defects such as discontinuity and pores may occur during the manufacturing process. Defect identification is the key to monitoring and quality assessments of the additive manufacturing process. This study proposes a novel acoustic signal-based defect identification method for DED-arc via wavelet time-frequency diagrams. With the continuous wavelet transform, one-dimensional (1D) acoustic signals acquired in situ during manufacturing are converted into two-dimensional (2D) time-frequency diagrams to train, validate, and test the convolutional neural network (CNN) models. In this study, several CNN models were examined and compared, including AlexNet, ResNet-18, VGG-16, and MobileNetV3. The accuracy of the models was 96.35%, 97.92%, 97.01%, and 98.31%, respectively. The findings demonstrate that the energy distribution of normal and abnormal acoustic signals has significant differences in both the time and frequency domains. The proposed method is verified to identify defects effectively in the manufacturing process and advance the identification time.

Design of laser-powder coupling for high-speed laser direct energy deposition

High-speed laser direct energy deposition (DED-LB) is developed to enhance deposition efficiency while maintaining build quality, compared to conventional DED-LB. The core of designing high-speed DED-LB involves formulating the laser-powder coupling, through optimizing nozzle structural and deposition process parameters. This study developed an analytical model to delineate the coupling mechanisms between laser beam and discontinuous coaxial powder stream (DCPS) comprised of individual single powder streams (SPSs). A data pretreatment method, involving gray processing, normalization, and renormalization of the thermal images successively, was applied to validate the model. Simulation results indicate that the DCPS spot size and SPS particle temperature distribution are predominantly influenced, respectively, by the nozzle structural and deposition process parameters. Through jointly designing the nozzle structural and deposition process parameters, a high deposition rate of high-speed DED-LB, which is 1.7 times that of conventional DED-LB, was achieved. This paper pioneers a new design methodology for high-speed DED-LB.

The Influence of Bias Voltage on the Structure and Properties of TiZrNbMo Coating Deposited by Magnetron Sputtering

TiZrNbMo coatings have been deposited using the direct current pulsed magnetron sputtering method in an argon atmosphere. The synthesis processes have been conducted under various process parameters. The structure (chemical and phase composition) and mechanical properties of the obtained multicomponent coatings are investigated as a function of plasma modulation frequency (10 Hz and 1000 Hz) and substrate bias (0 to −150 V). It is the case that an increase in the substrate bias decreases the deposition rate and alters the coating’s chemical composition. The latter leads to a Ti concentration decrease and a simultaneous increase in Mo and Nb concentrations in the final coating material. X-ray diffraction measurements indicate a single-phase BCC structure, with grain size decreasing as substrate bias increases. This ultimately forms an amorphous–nanocrystalline structure at −150 V. The mechanical properties of the multicomponent TiZrNbMo coatings have been determined using the nanoindentation method. The maximum values of hardness (13.45 GPa) and elastic modulus (188.6 GPa) are achieved at a substrate bias of −150 V. We also show that the minimum elastic modulus (41.8 GPa) is achieved at an intermediate substrate bias of −100 V.

The Effect of Interlayer Delay on the Heat Accumulation, Microstructures, and Properties in Laser Hot Wire Directed Energy Deposition of Ti-6Al-4V Single-Wall.

Laser hot wire directed energy deposition (LHW-DED) is a layer-by-layer additive manufacturing technique that permits the fabrication of large-scale Ti-6Al-4V (Ti64) components with a high deposition rate and has gained traction in the aerospace sector in recent years. However, one of the major challenges in LHW-DED Ti64 is heat accumulation, which affects the part quality, microstructure, and properties of as-built specimens. These issues require a comprehensive understanding of the layerwise heat-accumulation-driven process-structure-property relationship in as-deposited samples. In this study, a systematic investigation was performed by fabricating three Ti-6Al-4V single-wall specimens with distinct interlayer delays, i.e., 0, 120, and 300 s. The real-time acquisition of high-fidelity thermal data and high-resolution melt pool images were utilized to demonstrate a direct correlation between layerwise heat accumulation and melt pool dimensions. The results revealed that the maximum heat buildup temperature of the topmost layer decreased from 660 °C to 263 °C with an increase to a 300 s interlayer delay, allowing for better control of the melt pool dimensions, which then resulted in improved part accuracy. Furthermore, the investigation of the location-specific composition, microstructure, and mechanical properties demonstrated that heat buildup resulted in the coarsening of microstructures and, consequently, the reduction of micro-hardness with increasing height. Extending the delay by 120 s resulted in a 5% improvement in the mechanical properties, including an increase in the yield strength from 817 MPa to 859 MPa and the ultimate tensile strength from 914 MPa to 959 MPa. Cooling rates estimated at 900 °C using a one-dimensional thermal model based on a numerical method allowed us to establish the process-structure-property relationship for the wall specimens. The study provides deeper insight into the effect of heat buildup in LHW-DED and serves as a guide for tailoring the properties of as-deposited specimens by regulating interlayer delay.

Effective removal of uranium (VI) with a SDBS doped PPy-SUS304 electrode from alkaline wastewater using electrodeposition strategy

The immobilization of uranium in nuclear wastewater is of paramount importance for environmental and human health. However, there is a paucity of research on the immobilization of uranium in alkaline wastewater, particularly with regards to the application of novel electrodes. This article presents the utilization of an electrochemically polymerized polypyrrole stainless steel (PPy-SUS304) electrode for the effective electrochemical deposition and removal of uranium from alkaline wastewater containing uranium. According to the electrodeposition results, the uranium deposition efficiency of the novel electrode reached 96.82 %, with a uranium deposition rate of 0.048 mg U/(h·cm2) and a charge efficiency of 0.055 mg U/C. These findings demonstrate the successful electrochemical reduction of UO2(CO3)34- in alkaline uranium-containing wastewater using the novel electrode, resulting in improved charge deposition efficiency. The electrode surface products were investigated using scanning electron microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDS), and X-Ray Photoelectron Spectroscopy (XPS). The SEM and EDS results demonstrate the formation of a uniform PPy film on the surface of SUS304. In addition, the White light interferometer (WLI) test reveals that the PPy-SUS304 electrode exhibits increased roughness compared to the SUS304 electrode. The XPS results revealed that the electrode surface products of PPy-SUS304 were actually U compounds constituted of U(IV) oxides or hydroxides. This study provides a new perspective for the development of novel electrodes to suppress side reactions and efficiently recover uranium from alkaline uranium-containing wastewater.

Edaphic factors mediate the responses of forest soil respiration and its components to nitrogen deposition along an urban-rural gradient

Exploring the influences of nitrogen deposition on soil carbon (C) flux is necessary for predicting C cycling processes; however, few studies have investigated the effects of nitrogen deposition on soil respiration (Rs), autotrophic respiration (Ra) and heterotrophic respiration (Rh) across urban-rural forests. In this study, a 4-year simulated nitrogen deposition experiment was conducted by treating the experimental plots with 0, 50, or 100 kg·ha−1·year−1 of nitrogen to check out the mechanisms of nitrogen deposition on Rs, Ra, and Rh in urban-rural forests. Our finding indicated a positive association between soil temperature and Rs. Soil temperature sensitivity was significantly suppressed in the experimental plots treated with 100 kg·ha−1·year−1 of nitrogen only in terms of the urban forest Rs and Ra and the rural forest Ra. Nitrogen treatment did not significantly increase Rs and had different influencing mechanisms. In urban forests, nitrogen addition contributed to Rh by increasing soil microbial biomass nitrogen and inhibited Ra by increasing soil ammonium‑nitrogen concentration. In suburban forests, the lack of response of Rh under nitrogen addition was due to the combined effects of soil ammonium‑nitrogen and microbial biomass nitrogen; the indirect effects from nitrate‑nitrogen also contributed to a divergent effect on Ra. In rural forests, the soil pH, dissolved organic C, fine root biomass, and microbial biomass C concentration were the main factors mediating Rs and its components. In summary, the current rate of nitrogen deposition is unlikely to result in significant increases in soil C release in urban-rural forests, high nitrogen deposition is beneficial for reducing the temperature sensitivity of Rs in urban forests. The findings grant a groundwork for predicting responses of forest soil C cycling to global change in the context of urban expansion.

Quartz grain microtextures of Holocene sebkhas sediments in southeast Tunisia: Implications for sedimentary processes and depositional environments

Detrital quartz grains extracted from sebkha sediments in southeastern Tunisia underwent scanning electron microscopy analysis to identify sediment sources and assess the influence of the saline environment on the grains. Core sediments collected from Sebkha el Melah and Sebkha Mhabeul cover the last 5000 and 2000 BP, respectively. The uppermost Unit III, present in both cores, exhibits two distinct facies based on the mechanical microtextures of its quartz grains. The aeolian facies sediments are characterized by quartz grains with rounded outlines, upturned plates, and crescentic percussion marks. In contrast, the fluvial facies sediments are associated with quartz grains featuring subangular outlines, v-shaped percussion cracks, conchoidal fractures. Observations on the quartz grains of the sebkhas suggest multiple transportation and processing events, indicating long-distance transport and rapid deposition rates. The majority of quartz grains appear to originate from the surrounding terrain, reflecting the dynamic geological history of the region. This study delves into the connection between microtexture variations on quartz grain surfaces and specific historical climatic conditions in the sebkhas. By examining geochemical variations along the cores, facies with elevated salt concentrations corresponding to warmer periods reveal extensively weathered quartz grains. This substantial chemical alteration is evident through microtextures such as oriented etch pits, anastomosed dissolution networks and solution crevasses. The profound dissolution has significantly impacted the quartz lattice, resulting in the decomposition of the grains and the formation of "cauliflower" or "spongy" shapes, erasing prior microtextures. Conversely, during less warm periods, quartz dissolution was less severe, thereby preserving microtextures.Sand grain surfaces are notably sensitive to both transport processes and variations in the physicochemical environment. In the hypersaline and confined environments of sebkhas in southeastern Tunisia, potent post-sedimentary processes can obliterate and obscure the original microtextures recorded on grains from previous environments due to highly fluctuating physicochemical conditions.

Thermophoresis-Induced Polymer-Driven Destabilization of Gold Nanoparticles for Optically Directed Assembly at Interfaces.

The limitations of conventional template-based methods for the deposition of nanoparticle assemblies into defined patterns on solid substrates call for the development of techniques that do not require templates or lithographic masks. The use of optically-induced thermal gradients to drive the migration of colloids toward or away from a laser spot, known as opto-thermophoresis, has shown promise for the low-power trapping and optical manipulation of a variety of colloidal species. However, the printing of colloids using this technique has so far not been established. Herein, a method for the optically directed printing of noble metal nanoparticles, specifically gold nanospheres is reported. The thermophoresis of the polymer polyvinylpyrrolidone and gold nanospheres toward a laser spot led to the deposition of nanoparticle aggregates, capable of serving as surface-enhanced Raman scattering substrates. The influence of heating laser power and the concentrations of polymer, salt, and surfactant on the nanoparticle deposition rate and structure of the printed pattern are studied, showing that a variety of conditions can permit printing, suggesting facile generalization to different nanoparticle compositions, sizes, and shapes. These findings will greatly benefit future efforts for directed nanoparticle assembly, and drive applications in sensing, photothermal heating, and relevant applications in biomedicine and devices.

Study of dust deposition pattern in the respiratory tract of dust particles less than 10 μm in size

The turbulent disturbances of airflow at different respiratory intensities influence the deposition characteristics of dust. The dust concentration during inhalation is 62.3% higher than that during exhalation. During the respiratory process, the turbulent disturbance phenomenon in the inspiratory phase has a dominant influence on dust deposition. At a respiratory intensity range of 15–45 L/min, the final deposition of particles is mainly influenced by the inhalation airflow, while in the range of 60–90 L/min it is mainly influenced by the exhalation airflow. Particle size affected the deposition characteristics, with the deposition of 7.07-μm dust greatly affected by airflow conditions, with a variation in the deposition rate of 56.3%. As the particle size increased, particles less than 10 μm were more frequently deposited in the right nasal cavity (which has an open spatial structure) than the left nasal cavity, as well as in the thick and short right bronchus.

Effects of High Dietary Starch Levels on the Growth Performance, Liver Function, and Metabolome of Largemouth Bass (Micropterus salmoides)

In this study, we conducted a 16-week feeding trial to investigate the effects of a high-cassava starch diet on growth performance, liver function, and metabolism in largemouth bass (Micropterus salmoides). We formulated five diets containing varying levels of cassava starch: 12%, 9%, 6%, 3%, and 0% (termed M12, M9, M6, M3, and M0, respectively). We distributed these diets among largemouth bass with the initial body weight of 83.33 ± 0.55 g via an in-pond “raceway” aquaculture system. Our findings suggest that high level (12%) of cassava starch dietary inclusion adversely affected growth performance metrics such as weight gain rate and specific growth rate, along with feed utilization efficiency indicators, including protein efficiency, protein deposition rate, and the apparent digestibility of dry matter and protein. This negative impact was accompanied by a decrease in intestinal amylase activity. Through further transcriptomic analysis, we identified several key genes associated with carbohydrate metabolism, which underwent changes influencing liver function. Kyoto Encyclopedia of Genes and Genomes (KEGG) pathway analysis revealed the involvement of these differentially expressed genes (DEGs) in the tricarboxylic acid cycle (TCA cycle). Comparative metabolomics analysis further indicated that the M9 group showed significant enrichment in pathways related to amino acid metabolism and alterations in the levels of metabolites involved in carbohydrate metabolism. In conclusion, our study demonstrates that incorporating up to 9% cassava starch in the diet can enhance growth performance in largemouth bass by stimulating digestive enzyme activities and promoting glucose utilization.

Effect of pulse interval on deposition of diamond-like carbon through high-power impulse magnetron sputtering

A diamond-like carbon (DLC) film was deposited using unipolar-double-pulse high-power pulsed magnetron sputtering, aimed at enhancing both film density and deposition rate. The pulse interval between the 1st and 2nd pulses, with negative polarity applied to the target, was varied from 15 to 200 μs. Temporal variations in the flux and energy of C+ and Ar+ incident to the DLC film were analyzed through energy-resolved and time-resolved mass spectrometry to clarify the ion generation process during the 1st and 2nd pulses. The contribution of ionic species in forming the DLC film through HiPIMS was clarified through mass spectrometry, Raman scattering spectroscopy, and X-ray reflectivity analyses. Reducing the pulse interval increased the deposition rate, and the film density of the DLC film was improved at a pulse interval of approximately 40 μs. Overall, the implementation of a double pulse with the appropriate pulse interval can help enhance both the film density and deposition rate.