Coulombic Efficiency Research Articles

In Situ Construction of Specific SEI Layer Affords Effective Prelithiation.

Silicon-based anodes have been attracting attention due to their high theoretical specific capacity, but their low initial Coulombic efficiency (ICE) seriously hinders their commercial application. Direct contact prelithiation is considered to be one of the effective means of solving this problem. By means of prelithiation, a specific solid electrolyte interphase (SEI) was constructed, which inhibited the volume expansion of the SiO/C composite anode during prelithiation and reduced the local current generated when the lithium source was in contact with the anode. On the one hand, it can reduce the side reactions derived from the decomposition of electrolytes in the prelithiation process, and on the other hand, it can slow down the prelithiation process and inhibit the volume expansion of the SiO/C composite anode in the prelithiation process. The results of XPS, TOF-SIMS, and other tests show that the use of an electrolyte whose main component is LiTFSI can construct SEI film whose main component is LiF, which to a certain extent can slow down the rate of prelithiation, reduce the local current generated when the lithium source is in contact with the negative electrode, minimize the occurrence of side reactions, and inhibit the volume expansion of the negative electrode material. The full battery assembled with NCM111 positive electrode still exhibits 83.5% capacity retention after 500 cycles at 1 C current density. These studies provide some ideas to enhance the performance of silicon-based materials.

Modulating Surface Architecture and Electronic Conductivity of Li-rich Manganese-Based Cathode.

Li-rich manganese-based cathode (LRMC) has attracted intense attention to developing advanced lithium-ion batteries with high energy density. However, LRMC is still plagued by poor cyclic stability, undesired rate capacity, and irreversible oxygen release. To address these issues, herein, a feasible polyvinylidene fluoride (PVDF)-assisted interface modification strategy is proposed for modulating the surface architecture and electronic conductivity of LRMC by intruding the F-doped carbon coating, spinel structure, and oxygen vacancy on the LRMC, which can greatly enhance the cyclic stability and rate capacity, and restrain the oxygen release for LRMC. As a result, the modified material delivers satisfactory cyclic performance with a capacity retention of 90.22% after 200 cycles at 1C, an enhanced rate capacity of 153.58mAhg-1 at 5C and 126.32mAhg-1 at 10C, and an elevated initial Coulombic efficiency of 85.63%. Moreover, the thermal stability, electronic conductivity, and structure stability of LRMC are also significantly improved by the PVDF-assisted interface modification strategy. Therefore, the strategy of simultaneously modulating the surface architecture and the electronic conductivity of LRMC provides a valuable idea to improve the comprehensive electrochemical performance of LRMC, which offers a promising reference for designing LRMC with high electrochemical performance.

Thin-film flexible zinc hybrid electrochemical device integrating three chemical pathways

Combining the strengths of supercapacitors and batteries onto a single device is a holy grail which would enable many applications to be covered by the same device. Here, we firstly develop a hybrid electrochemical device integrating chemical pathways of a zinc hybrid supercapacitor, an electrolytic MnO2-zinc battery and a zinc-iodide battery. The integrated hybrid devices demonstrate a capacity of 453.1 mAh/g (corresponding to an energy of 400.4 Wh/kg, based on weight of activated carbon) and a capacitance of 720.7 F/g at output power of 220.3 W/kg. The three different chemical pathways symbiotically work together, achieving improved cycling performance, shelf-life and Coulombic Efficiencies compared to any of its constituent systems individually.

Colloidal Synthesis of Cu3N Nanorods and Construction of Cu3N-Cu2O Heteronanostructures via Epitaxial Growth.

The synthesis of transition metal nitrides nanocrystals (TMNs NCs) has posed a significant challenge due to the limited reactivity of nitrogen sources at lower temperatures and the scarcity of available synthesis methods. In this study, we present a novel colloidal synthesis strategy for the fabrication of Cu3N nanorods (NRs). It is found that the trace oxygen (O2) plays an important role in the synthesis process. And a new mechanism for the formation of Cu3N is proposed. Subsequently, by employing secondary lateral epitaxial growth, the Cu3N-Cu2O heteronanostructures (HNs) can be prepared. The Cu3N NRs and Cu3N-Cu2O HNs were evaluated as precursor electrocatalysts for the CO2 reduction reaction (CO2RR). The Cu3N-Cu2O HNs demonstrate remarkable selectivity and stability with ethylene (C2H4) Faradaic efficiency (FE) up to 55.3%, surpassing that of Cu3N NRs. This study provides innovative insights into the reaction mechanism of colloidal synthesis of TMNs NCs and presents alternative options for designing cost-effective electrocatalysts to achieve carbon neutrality.

Heterogeneous interface engineering of CoPSe and FePSe3 on open frameworks for boosting highly efficient overall water splitting

Enhancing intrinsic activity of nanostructured heterogeneous catalysts is an effective strategy for improving electrocatalytic performance for hydrogen/oxygen evolution reactions (HER/OER), but it remains challenging. Here, phosphorus (P) and selenium (Se) atoms are incorporated into an open Co-Fe-based Prussian blue analogues to form a heterostructure consisting of CoPSe and FePSe3 via a one-step pyrolysis strategy. The CoPSe/FePSe3 heterojunction greatly reduces the overpotential for HER (91 mV) or OER (172 mV), which is close to that of Pt/C or much better than that of RuO2, respectively. Co-doping of P and Se non-metallic atoms promotes the reaction kinetics and the exposure of active sites in the framework structure with a large specific surface area. The interactions between CoPSe and FePSe3 can eagerly promote the interfacial electron transfer to enhance HER/OER activities. The carbon skeleton can effectively avoid the fast corrosion/aggregation of the embedded CoPSe/FePSe3 heterojunctions, thereby enhancing the catalytic/structural stability for HER/OER. Importantly, for overall water splitting, the electrolyzer with CoPSe/FePSe3 catalyst only requires an overpotential of 0.35 V to achieve a long-term stability (36 h) at 10 mA cm−2, with Faradaic efficiencies near 100 %. This work sheds a new light on promotion of intrinsic activity of heterostructured catalysts for water splitting.

Photoelectrocatalytic Synthesis of Urea from Carbon Dioxide and Nitrate over a Cu2O Photocathode

AbstractTransformation of carbon dioxide and nitrate ions into urea offers an attractive route for both nitrogen fertilizer production and environmental remediation. However, achieving this transformation under mild conditions remains challenging. Herein, we report an efficient photoelectrochemical method for urea synthesis by co‐reduction of carbon dioxide and nitrate ion over a Cu2O photocathode, delivering urea formation rate of 29.71±2.20 μmol g−1 h−1 and Faradaic efficiency (FE) of 12.90±1.15 % at low external potential (−0.017 V vs. reversible hydrogen electrode). Experimental data combined with theoretical calculations suggest that the adsorbed CO* and NO2* species are the key intermediates, and associated C−N coupling is the rate‐determining step. This work demonstrates that Cu2O is an efficient catalyst to drive co‐reduction of CO2 and NO3− to urea under light irradiation with low external potential, showing great opportunity of photoelectrocatalysis as a sustainable tool for value‐added chemical synthesis.

Insight into Fluoride Additives to Enhance Ammonia Production from Lithium-Mediated Electrochemical Nitrogen Reduction Reaction.

Demands for green ammonia production increase due to its application as a proton carrier, and recent achievements in electrochemical Li-mediated nitrogen reduction reactions (Li-NRRs) show promising reliability. Here, it is demonstrated that F-containing additives in the electrolyte improve ammonia production by modulating the solid electrolyte interphase (SEI). It is suggested that the anionic additives with low lowest unoccupied molecular orbital levels enhance efficiency by contributing to the formation of a conductive SEI incorporated with LiF. Specifically, as little as 0.3wt.% of BF4 - additive to the electrolyte, the Faradaic efficiency (FE) for ammonia production is enhanced by over 15% compared to an additive-free electrolyte, achieving a high yield of 161 ± 3nmol s-1 cm-2. The BF4 - additive exhibits advantages, with decreased overpotential and improved FE, compared to its use as the bulk electrolyte. The observation of the Li3N upper layer implies that active Li-NRR catalytic cycles are occurring on the outermost SEI, and density functional theory simulations propose that an SEI incorporated with LiF facilitates energy profiles for the protonation by adjusting the binding energies of the intermediates compared to bare copper. This study unlocks the potential of additives and offers insights into the SEIs for efficient Li-NRRs.

Colloidal Synthesis of Cu3N Nanorods and Construction of Cu3N-Cu2O Heteronanostructures via Epitaxial Growth.

The synthesis of transition metal nitrides nanocrystals (TMNs NCs) has posed a significant challenge due to the limited reactivity of nitrogen sources at lower temperatures and the scarcity of available synthesis methods. In this study, we present a novel colloidal synthesis strategy for the fabrication of Cu3N nanorods (NRs). It is found that the trace oxygen (O2) plays an important role in the synthesis process. And a new mechanism for the formation of Cu3N is proposed. Subsequently, by employing secondary lateral epitaxial growth, the Cu3N-Cu2O heteronanostructures (HNs) can be prepared. The Cu3N NRs and Cu3N-Cu2O HNs were evaluated as precursor electrocatalysts for the CO2 reduction reaction (CO2RR). The Cu3N-Cu2O HNs demonstrate remarkable selectivity and stability with ethylene (C2H4) Faradaic efficiency (FE) up to 55.3%, surpassing that of Cu3N NRs. This study provides innovative insights into the reaction mechanism of colloidal synthesis of TMNs NCs and presents alternative options for designing cost-effective electrocatalysts to achieve carbon neutrality.

Optimized and cost-effective elemental-sulfur sodium polysulfide/sodium bromide aqueous electrolytes for redox flow batteries

Redox flow batteries (RFBs) can potentially revolutionize large-scale energy-storage technologies for both conventional (fossil fuel) and modern (renewable) electric power systems. This has stimulated the development of new methods for reducing the costs of such batteries by lowering material costs and increasing the energy density. Driven by the abundance and low costs of sulfur and bromine salts, this study investigates the viability of an aqueous flow battery system, in which sodium bromide (NaBr) is used as a catholyte, and a novel electrolyte called elemental added sulfur sodium polysulfide (EASSP) is utilized as an anolyte. The molar ratio of elemental sulfur to sodium (S/Na) in the sodium polysulfide solution is maintained at 1:4. Various concentrations of the EASSP and NaBr electrolytes are examined, and their optimal values corresponding to the minimum overpotential are determined. A bromine–polysulfide redox flow battery (BPRFB) containing a 1.4 M EASSP anolyte and 8 M NaBr catholyte is charged and discharged for 5 min, which results in a capacity of 17 mAh (3.4 mAh cm−2) at a current density of 40 mA cm−2. The cyclic performance of the BPRFB is characterized by a capacity of 17 mAh at 40 mA cm−2, which is retained over 150 cycles with a 98 % coulombic efficiency. The assembled BPRFB cell with the optimized electrolyte composition (1.4 M EASSP: 8 M NaBr) exhibits constant current (without leakage) and potential. The findings of this work demonstrate a high application potential of the developed anolyte for BPRFBs, which is highly soluble in water, inexpensive, and can be scaled up for energy storage applications.

Highly Efficient Electrosynthesis of Urea from CO2 and Nitrate by a Metal‐Organic Framework with Dual Active Sites

Electrosynthesis of urea from CO2 and NO3− is a sustainable alternative to energy‐intensive industrial processes. The challenge hindering the progress is the development of advanced electrocatalysts that yield urea with both high Faradaic efficiency (FE) and current density. In this work, we designed a new two‐dimensional MOF, namely PcNi−Fe−O, constructed by nickel‐phthalocyanine (NiPc) ligands and square‐planar FeO4 nodes. PcNi−Fe−O exhibits remarkable performance to yield urea at a high current density of 10.1 mA cm−2 with a high FE(urea) of 54.1% in a neutral aqueous solution, surpassing those of most reported electrocatalysts. No obvious performance degradation was observed over 20 hours of continuous operation at the current density of 10.1 mA cm−2. By expanding the electrode area to 25 cm2 and operating for 8 hours, we obtained 0.164 g of high‐purity urea, underscoring its potential for industrial applications. Mechanism study unveiled the enhanced performance might be ascribed to the synergistic interaction between NiPc and FeO4 sites. Specifically, NH3 produced at the FeO4 site can efficiently migrate and couple with the *NHCOOH intermediate adsorbed on the urea‐producing site (NiPc). This synergistic effect results in a lower energy barrier for C−N bond formation than those of the reported catalysts with single active sites.

Highly Efficient Electrosynthesis of Urea from CO2 and Nitrate by a Metal-Organic Framework with Dual Active Sites.

Electrosynthesis of urea from CO2 and NO3- is a sustainable alternative to energy-intensive industrial processes. Thechallenge hindering the progress is the development of advanced electrocatalysts thatyield urea with both high Faradaic efficiency (FE) and current density. In this work, we designeda new two-dimensional MOF, namely PcNi-Fe-O, constructed by nickel-phthalocyanine (NiPc) ligands and square-planar FeO4 nodes. PcNi-Fe-O exhibits remarkable performance to yield urea at a high current density of 10.1 mA cm-2 with a high FE(urea) of 54.1% in a neutral aqueous solution, surpassing those of most reported electrocatalysts. No obvious performance degradation was observed over 20 hours of continuous operation at the current density of 10.1 mA cm-2. By expanding the electrode area to 25 cm2 and operating for 8 hours, we obtained 0.164 g of high-purity urea, underscoring its potential for industrial applications. Mechanism study unveiled the enhanced performance might be ascribed to the synergistic interaction between NiPc and FeO4 sites. Specifically, NH3 produced at the FeO4 site can efficiently migrate and couple with the *NHCOOH intermediate adsorbed on the urea-producing site (NiPc). This synergistic effect results in a lower energy barrier for C-N bond formation than those of the reported catalysts with single active sites.

Interface Engineering of the Cu1.5Mn1.5O4/CeO2 Heterostructure for Highly Efficient Electrocatalytic Nitrate Reduction to Ammonia.

The electrochemical nitrate reduction reaction (NO3RR) is considered a sustainable technology to convert the nitrate pollutants to ammonia. However, developing highly efficient electrocatalysts is necessary and challenging given the slow kinetics of the NO3RR with an eight-electron transfer process. Here, a Cu1.5Mn1.5O4 (CMO)/CeO2 heterostructure with rich interfaces is designed and fabricated through an electrospinning and postprocessing technique. Benefiting from the strong coupling between CMO and CeO2, the optimized CMO/CeO2-2 catalyst presents excellent NO3RR performance, with NH3 Faraday efficiency (FE) up to 93.07 ± 1.45% at -0.481 V vs reversible hydrogen electrode (RHE) and NH3 yield rate up to 48.06 ± 1.32 mg cm-2 h-1 at -0.681 V vs RHE. Theoretical calculations demonstrate that the integration of CeO2 with CMO modulates the adsorption/desorption process of the reactants and intermediates, showing a reduced energy barrier in the rate determination step of NO* to N* and achieving an outstanding NO3RR performance.

Screening of Intermetallic Compounds Based on Intermediate Adsorption Equilibrium for Electrocatalytic Nitrate Reduction to Ammonia.

Electrocatalytic nitrate (NO3-) reduction reaction (NO3RR) holds great potential for the conversion of NO3- contaminants into valuable NH3 in a sustainable method. Unfortunately, the nonequilibrium adsorption of intermediates and sluggish multielectron transfer have detrimental impacts on the electrocatalytic performance of the NO3RR, posing obstacles to its practical application. Herein, we initially screen the adsorption energies of three key intermediates, i.e., *NO3, *NO, and *H2O, along with the d-band centers on 21 types of transition metal (IIIV and IB)-Sb/Bi-based intermetallic compounds (IMCs) as electrocatalysts. The results reveal that hexagonal CoSb IMCs possess the optimal adsorption equilibrium for key intermediates and exhibit outstanding electrocatalytic NO3RR performance with a Faradaic efficiency of 96.3%, a NH3 selectivity of 89.1%, and excellent stability, surpassing the majority of recently reported NO3RR electrocatalysts. Moreover, the integration of CoSb IMCs/C into a novel Zn-NO3- battery results in a high power density of 11.88 mW cm-2.

Screening of Intermetallic Compounds Based on Intermediate Adsorption Equilibrium for Electrocatalytic Nitrate Reduction to Ammonia.

Electrocatalytic nitrate (NO3-) reduction reaction (NO3RR) holds great potential for the conversion of NO3- contaminants into valuable NH3 in a sustainable method. Unfortunately, the nonequilibrium adsorption of intermediates and sluggish multielectron transfer have detrimental impacts on the electrocatalytic performance of the NO3RR, posing obstacles to its practical application. Herein, we initially screen the adsorption energies of three key intermediates, i.e., *NO3, *NO, and *H2O, along with the d-band centers on 21 types of transition metal (IIIV and IB)-Sb/Bi-based intermetallic compounds (IMCs) as electrocatalysts. The results reveal that hexagonal CoSb IMCs possess the optimal adsorption equilibrium for key intermediates and exhibit outstanding electrocatalytic NO3RR performance with a Faradaic efficiency of 96.3%, a NH3 selectivity of 89.1%, and excellent stability, surpassing the majority of recently reported NO3RR electrocatalysts. Moreover, the integration of CoSb IMCs/C into a novel Zn-NO3- battery results in a high power density of 11.88 mW cm-2.

Anionic Surfactant-Tailored Interfacial Microenvironment for Boosting Electrochemical CO2 Reduction.

Both the catalyst and electrolyte deeply impact the performance of the carbon dioxide reduction reaction (CO2RR). It remains a challenge to design the electrolyte compositions for promoting the CO2RR. Here, typical anionic surfactants, dodecylphosphonic acid (DDPA) and its analogues, are employed as electrolyte additives to tune the catalysis interface where the CO2RR occurs. Surprisingly, the anionic surfactant-tailored interfacial microenvironment enables a set of typical commercial catalysts for the CO2RR to deliver a significantly enhanced selectivity of carbon products in both neutral and acidic electrolytes. Mechanistic studies disclose that the DDPA addition restructures the interfacial hydrogen-bond environment via increasing the weak H-bonded water, thus promoting the CO2 protonation to CO. Specifically, in an H-type cell, the Faradaic efficiency of CO increases from 70 to 98% at -1.0 V versus the reversible hydrogen electrode. Furthermore, in a flow cell, the DDPA-containing electrolyte maintains over 90% FECO from 50-400 mA cm-2. Additionally, this electrolyte modulation strategy can be extended to acidic CO2RR with a pH of 1.5-3.5.

Insights into the Electrochemical CO2RR Performance and Binding of Small Molecules on Quaternary Thiospinels Ag2FeSn3S8 and Cu2FeSn3S8.

Using a mechanical synthesis method in the form of ball milling and an additional annealing step, a novel and accelerated route for the synthesis of the thiospinels toyohaite (Ag2FeSn3S8) and rhodostannite (Cu2FeSn3S8) was discovered. Both thiospinels display faradaic efficiencies of up to 73% for CO2 reduction to CO using an organic electrolyte in an H-type cell. The materials were furthermore implemented in a zero-gap electrolyzer, with toyohaite producing 22% CO and 52% H2 at 100 mA cm-2 and rhodostannite 28% CO and 37% H2. The catalytically active sites are studied using density functional theory, revealing strong CO binding interactions on both Ag and Cu, whereas Sn is found to contribute to the decomposition of Ag2FeSn3S8 and Cu2FeSn3S8 by coordination with oxygen. Postmortem analysis of the thiospinel-based electrodes by means of SEM-EDX, XRD, XPS, and Mössbauer spectroscopy showed sulfur leaching from the catalysts after applying 100 mA cm-2. These spectroscopic results-in conjunction with DFT calculations of the oxidized surfaces-suggest that the catalytically active species consists of metal oxides. As a conversion of the metal sulfides into the corresponding metallic species was observed via XRD, the decomposition pathways of both catalysts were also computed using DFT; thus, elucidating the energetically most favorable decomposition products and expanding the possible composition of the catalysts postelectrolysis.

Anionic Surfactant-Tailored Interfacial Microenvironment for Boosting Electrochemical CO2 Reduction.

Both the catalyst and electrolyte deeply impact the performance of the carbon dioxide reduction reaction (CO2RR). It remains a challenge to design the electrolyte compositions for promoting the CO2RR. Here, typical anionic surfactants, dodecylphosphonic acid (DDPA) and its analogues, are employed as electrolyte additives to tune the catalysis interface where the CO2RR occurs. Surprisingly, the anionic surfactant-tailored interfacial microenvironment enables a set of typical commercial catalysts for the CO2RR to deliver a significantly enhanced selectivity of carbon products in both neutral and acidic electrolytes. Mechanistic studies disclose that the DDPA addition restructures the interfacial hydrogen-bond environment via increasing the weak H-bonded water, thus promoting the CO2 protonation to CO. Specifically, in an H-type cell, the Faradaic efficiency of CO increases from 70 to 98% at -1.0 V versus the reversible hydrogen electrode. Furthermore, in a flow cell, the DDPA-containing electrolyte maintains over 90% FECO from 50-400 mA cm-2. Additionally, this electrolyte modulation strategy can be extended to acidic CO2RR with a pH of 1.5-3.5.

Utilizing rubber plant leaf petioles derived activated carbon for high-performance supercapacitor electrodes

This research introduces a novel and sustainable method that exploits the untapped potential of waste biomass, specifically converting dead leaf petioles from Ficus elastica, an industrial crop commonly known as rubber plants, into high-performance activated carbon (AC) for supercapacitor electrodes through a straightforward pyrolysis process. The prepared AC is used as an electrode substance to construct symmetrical supercapacitors. It underwent detailed morphological and structural analyses through various analytical instruments to assess the AC's performance and quality. Electrochemical assessments using a two-electrode configuration with 1 M KOH as the electrolyte revealed that the AC electrodes display exemplary characteristics of electric double-layer capacitance. This conclusion was drawn from observing cyclic voltammetry curves that were rectangular and symmetrical across scan rates ranging from 10 to 100 mV/s. Remarkably, at a scan rate of 10 mV/s, these AC electrodes achieved a specific capacitance of 128 F/g. The superior performance of the AC, when compared to other biomass-derived electrode materials, can be attributed to its extensive surface area and significant porosity. Moreover, electrodes crafted from AC derived from rubber plants showed remarkable durability over 10000 charge-discharge cycles, maintaining 89 % of their original capacitance and achieving a Coulombic efficiency of up to 87 %. During prolonged discharge periods, these electrodes exhibited a high specific capacitance, which contributed to achieving a power density of 200 W/kg and an energy density of 11.4 Wh/kg. This study highlights the viability of rubber plant waste in advanced energy storage systems and significantly contributes to sustainable material science. By offering an eco-friendly approach for supercapacitor electrode fabrication, this research aligns with global efforts towards sustainable energy storage technologies, demonstrating the practicality of environmentally benign materials in high-performance applications.

Dilute Electrolytes with Fluorine-free Ether Solvents for 4.5 V Lithium Metal Batteries.

The limited oxidation stability of ether solvents has posed significant challenges for their applications in high-voltage lithium metal batteries (LMBs). To tackle this issue, the prevailing strategy either adopts a high concentration of fluorinated salts or relies on highly fluorinated solvents, which will significantly increase the manufacturing cost and create severe environmental hazards. Herein, an alternative and sustainable salt engineering approach is proposed to enable the utilization of dilute electrolytes consisting of fluorine (F)-free ethers in high-voltage LMBs. The proposed 0.8 M electrolyte supports stable lithium plating-stripping with a high Coulombic efficiency of 99.47% and effectively mitigates the metal dissolution, phase transition, and gas release issues of the LiNi0.8Co0.1Mn0.1O2 (NCM811) cathode upon charging to high voltages. Consequently, the 4.5 V high-loading Li||NCM 811 cell shows a capacity retention of 75.2% after 300 cycles. Multimodal experimental characterizations coupled with theoretical investigations demonstrate that the boron-containing salt plays a pivotal role in forming the passivation layers on both anode and cathode. The present simple and cost-effective electrolyte design strategy offers a promising and alternative avenue for using commercially mature, environmentally benign, and low-cost F-free ethers in high-voltage LMBs.

Dilute Electrolytes with Fluorine‐free Ether Solvents for 4.5 V Lithium Metal Batteries

The limited oxidation stability of ether solvents has posed significant challenges for their applications in high‐voltage lithium metal batteries (LMBs). To tackle this issue, the prevailing strategy either adopts a high concentration of fluorinated salts or relies on highly fluorinated solvents, which will significantly increase the manufacturing cost and create severe environmental hazards. Herein, an alternative and sustainable salt engineering approach is proposed to enable the utilization of dilute electrolytes consisting of fluorine (F)‐free ethers in high‐voltage LMBs. The proposed 0.8 M electrolyte supports stable lithium plating‐stripping with a high Coulombic efficiency of 99.47% and effectively mitigates the metal dissolution, phase transition, and gas release issues of the LiNi0.8Co0.1Mn0.1O2 (NCM811) cathode upon charging to high voltages. Consequently, the 4.5 V high‐loading Li||NCM 811 cell shows a capacity retention of 75.2% after 300 cycles. Multimodal experimental characterizations coupled with theoretical investigations demonstrate that the boron‐containing salt plays a pivotal role in forming the passivation layers on both anode and cathode. The present simple and cost‐effective electrolyte design strategy offers a promising and alternative avenue for using commercially mature, environmentally benign, and low‐cost F‐free ethers in high‐voltage LMBs.