Conventional Wastewater Treatment Research Articles

Solar photocatalytic degradation of ciprofloxacin using biochar supported zinc oxide- tungsten oxide photocatalyst.

Ciprofloxacin (CIP) is an antibiotic used to treat bacterial infections. It is not completely broken down during conventional wastewater treatment processes and can persist in the environment, leading to the development of antibiotic-resistant bacteria. This study focuses on the solar photocatalytic degradation CIP using biochar-supported photocatalysts. The photocatalysts developed by combining ZnO and WO3 in different ratios (1:2, 1:1, 2:1) were supported on hemp herd biochar. The photocatalyst made with a ratio of 2:1:1 of ZnO:WO3:biochar (Z2W1H) reported the highest CIP degradation efficiency of 87.3% and TOC removal efficiency of 43.1% at a catalyst dosage of 2g/L, initial CIP concentration of 3mg/L, and treatment time of 150min. Subsequently, the effects of operating parameters on CIP degradation were investigated using central composite design (CCD). About 85.4% degradation efficiency of CIP was obtained at optimum conditions (pH ∼8.4, initial CIP concentration ∼4.4mg/L, catalytic dosage ∼3.4g/L) within 90min. A quadradic model was developed to interpret the linear and interactive effect of operating parameters on the CIP degradation efficiency with 2.24-4.59% error. The adsorption-desorption study showed around 42.21% of adsorbed CIP was desorbed from Z2W1H. Scavenger studies demonstrated that the CIP breakdown was notably done by the superoxide radical (O2•-). The mechanism of CIP degradation was adsorption on biochar and subsequent degradation by photocatalyst. The prevalent degradation reactions such as C-N bond cleavage, decarboxylation, decarbonylation, defluorination, and ring opening lead to formation of various intermediates. The Z2W1H reusability test showed ~ 4.2% decrease in CIP removal efficiency after three cycles.

Recent advances and challenges of the green ZnO-based composites biosynthesized using plant extracts for water treatment.

Recently, there has been a notable rise in the prevalence of persistent pollutants in the environment, posing a significant hazard due to their toxicity and enduring nature. Conventional wastewater treatment methods employed in treatment plants rarely address these persistent pollutants adequately. Meanwhile, the concept of green synthesis has garnered considerable attention, owing to its environmentally friendly approach that utilizes fewer toxic chemicals and solvents. The utilization of materials derived from sustainable sources presents a promising avenue for solving pressing environmental concerns. Among the various sources of biological agents, plants stand out for their accessibility, eco-friendliness, and rich reserves of phytochemicals suitable for material synthesis. The plant extract-mediated synthesis of zinc oxide nanoparticles (ZnONPs) has emerged as a promising solution for applications in wastewater treatment. Thorough investigations into the factors influencing the properties of these green ZnONPs are essential to establish a detailed and reliable synthesis process. Major weaknesses inherent in ZnONPs can be addressed by changing the optical, magnetic, and interface properties through doping with various semiconductor materials. Consequently, research efforts to mitigate water pollution are being driven by both the future prospects and limitations of ZnO-based composites. This review underscores the recent advancements of plant extract-mediated ZnONP composites for water treatment.

Artificial intelligence integration in conventional wastewater treatment techniques: techno-economic evaluation, recent progress and its future direction

Artificial intelligence integration in conventional wastewater treatment techniques: techno-economic evaluation, recent progress and its future direction

Artificial intelligence and machine learning for the optimization of pharmaceutical wastewater treatment systems: a review

AbstractThe access to clean and drinkable water is becoming one of the major health issues because most natural waters are now polluted in the context of rapid industrialization and urbanization. Moreover, most pollutants such as antibiotics escape conventional wastewater treatments and are thus discharged in ecosystems, requiring advanced techniques for wastewater treatment. Here we review the use of artificial intelligence and machine learning to optimize pharmaceutical wastewater treatment systems, with focus on water quality, disinfection, renewable energy, biological treatment, blockchain technology, machine learning algorithms, big data, cyber-physical systems, and automated smart grid power distribution networks. Artificial intelligence allows for monitoring contaminants, facilitating data analysis, diagnosing water quality, easing autonomous decision-making, and predicting process parameters. We discuss advances in technical reliability, energy resources and wastewater management, cyber-resilience, security functionalities, and robust multidimensional performance of automated platform and distributed consortium, and stabilization of abnormal fluctuations in water quality parameters.

Synthetic greywater treatment using a scalable granular activated carbon bioelectrochemical reactor

Greywater reuse has emerged as a promising solution for addressing water shortages. However, greywater needs treatment before reuse to meet the required water quality standards. Conventional wastewater treatment technologies are unsuitable for recreating highly decentralized domestic greywater. This study evaluated bioelectrochemical reactors (BERs) with granular activated carbon (GAC) as a sustainable alternative for developing decentralized and low-cost biological treatment systems. BERs using GAC as the anode material and conventional GAC biofilters (BFs) for synthetic greywater treatment were operated in batch mode for 110 days in two stages: (i) with polarized anodes at −150 mV vs. Ag/AgCl and (ii) as a microbial fuel cell with an external resistance of 1 kΩ. Anode polarization produced an electrosorption effect, increasing the ion removal of the BERs. Power production during the operation and cyclic voltammetry tests of the extracted granules revealed electrochemically active biofilm development on the BERs. Although low power density (0.193 ± 0.052 µW m−3) was observed in BERs, they showed a similar performance in sCOD removal (BER = 91.6–89.6 %; BF = 96.2–93.2 %) and turbidity removal (BER = 81–82 %; BF = 30–62 %) to BFs that used 50 % aeration. Additionally, scanning electron microscopy of sampled granules showed higher biomass formation in BER granules than in BF granules, suggesting a higher contribution of sessile (vs. planktonic) cells to the treatment. Thus, the results highlight the synergistic removal effect of the GAC-based BER. The scalable design presented in this study represents a proof-of-concept for developing BERs to use in decentralized greywater treatment systems.

Enhancing volatile fatty acid production in batch test reactors by modulating microbial communities with potassium permanganate

The shift from conventional wastewater treatment plants to biorefineries is one of the most environmentally and economically sustainable pathways for extracting valuable compounds from waste. Besides chemical-physical processes, microorganisms within sewage sludge utilize organic and inorganic pollutants in the wastewater as nutrients, leading to effective water purification. However, the remaining solid sludge residue, typically destined for specific landfills or incineration, could undergo microbial fermentation to produce volatile fatty acids (VFA), metabolic precursors for biopolymers. Increasing attention has been directed towards optimizing operational parameters to enhance VFA production during sewage sludge fermentation. This study examined the impact of potassium permanganate (PP) on microbial communities during the sewage sludge's acidogenic fermentation. The results highlighted the positive effect of PP treatment, which increased COD production and VFA yield up to 1263.5 mg/L and 664.2 mg COD/L, respectively. The presence of PP significantly enhances VFA yield promoting bacteria positively linked to VFA production.

Molecular Simulation Studies of Pharmaceutical Pollutant Removal (Rosuvastatin and Simvastatin) Using Novel Modified-MOF Nanostructures (UIO-66, UIO-66/Chitosan, and UIO-66/Oxidized Chitosan).

The ubiquitous presence of pharmaceutical pollutants in the environment significantly threatens human health and aquatic ecosystems. Conventional wastewater treatment processes often fall short of effectively removing these emerging contaminants. Therefore, the development of high-performance adsorbents is crucial for environmental remediation. This research utilizes molecular simulation to explore the potential of novel modified metal-organic frameworks (MOFs) in pharmaceutical pollutant removal, paving the way for the design of efficient wastewater treatment strategies. Utilizing UIO-66, a robust MOF, as the base material, we developed UIO-66 functionalized with chitosan (CHI) and oxidized chitosan (OCHI). These modified MOFs' physical and chemical properties were first investigated through various characterization techniques. Subsequently, molecular dynamics simulation (MDS) and Monte Carlo simulation (MCS) were employed to elucidate the adsorption mechanisms of rosuvastatin (ROSU) and simvastatin (SIMV), two prevalent pharmaceutical pollutants, onto these nanostructures. MCS calculations demonstrated a significant enhancement in the adsorption energy by incorporating CHI and OCHI into UIO-66. This increased ROSU from -14,522 to -16,459 kcal/mol and SIMV from -17,652 to -21,207 kcal/mol. Moreover, MDS reveals ROSU rejection rates in neat UIO-66 to be at 40%, rising to 60 and 70% with CHI and OCHI. Accumulation rates increase from 4 Å in UIO-66 to 6 and 9 Å in UIO-CHI and UIO-OCHI. Concentration analysis shows SIMV rejection surges from 50 to 90%, with accumulation rates increasing from 6 to 11 Å with CHI and OCHI in UIO-66. Functionalizing UIO-66 with CHI and OCHI significantly enhanced the adsorption capacity and selectivity for ROSU and SIMV. Abundant hydroxyl and amino groups facilitated strong interactions, improving performance over that of unmodified UIO-66. Surface functionalization plays a vital role in customizing the MOFs for pharmaceutical pollutant removal. These insights guide next-gen adsorbent development, offering high efficiency and selectivity for wastewater treatment.

Novel nanostructure approach for antibiotic decomposition in a spinning disc photocatalytic reactor

Conventional wastewater treatment processes are often unable to remove antibiotics with resistant compounds and low biological degradation. The need for advanced and sustainable technologies to remove antibiotics from water sources seems essential. In this regard, the effectiveness of a spinning disc photocatalytic reactor (SDPR) equipped with a visible light-activated Fe3O4@SiO2-NH2@CuO/ZnO core–shell (FSNCZ CS) thin film photocatalyst was investigated for the decomposition of amoxicillin (AMX), a representative antibiotic. Various characterization techniques, such as TEM, FESEM, EDX, AFM, XRD, and UV–Vis-DRS, were employed to study the surface morphology, optoelectronic properties, and nanostructure of the FSNCZ CS. Key operating parameters such as irradiation time, pH, initial AMX concentration, rotational speed, and solution flow rate were fine-tuned for optimization. The results indicated that the highest AMX decomposition (98.7%) was attained under optimal conditions of 60 min of irradiation time, a rotational speed of 350 rpm, a solution flow rate of 0.9 L/min, pH of 5, and an initial AMX concentration of 20 mg/L. Moreover, during the 60 min irradiation time, more than 69.95% of chemical oxygen demand and 61.2% of total organic carbon were removed. After the photocatalytic decomposition of AMX, there is a substantial increase in the average oxidation state and carbon oxidation state in SDPR from 1.33 to 1.94 and 3.2, respectively. Active species tests confirmed that ·OH and ·O2− played a dominant role in AMX decomposition. The developed SDPR, which incorporates a reusable and robust FSNCZ CS photocatalyst, demonstrates promising potential for the decomposition of organic compounds.

Impact of CeO2 modified cathode and PANI modified anode on tannery wastewater fed microbial fuel cell performance

Microbial fuel cell (MFC) technology is getting acceptance as an emphatic, sustainable and energy efficient alternative of conventional wastewater treatment strategies. MFCs utilize exoelectrogens as biocatalysts to degrade the complex organic substances present in wastewater with simultaneous power generation. The present study was aimed at investigating the impact of MFC electrode’s modification with CeO2 nanoparticles and polyaniline (PANI) on its performance characteristics. The hydrothermal approach was employed for the synthesis of CeO2 nanoparticles followed by their deposition on carbon cloth (CC) as MFC cathode, whereas MFC’s anode i.e., CF/NF was modified by in-situe deposition of PANI. The synthesized material was characterized with FTIR, XRD, SEM, EDX and BET analysis. The experiments were performed using dual chambered MFC fed with leather tannery wastewater using modified and unmodified electrodes. The highest outcomes of power density and corresponding current density were observed with PANI@NF composite anode and CeO2@CC as cathode i.e., 279.3 mW/m2 corresponding to the current density of 581.8 mA/m2. The same MFC electrode configuration resulted in highest COD reduction, i.e., 80 % and coulombic efficiency of 19.86 %. On the other hand, MFC equipped with PANI@CF anode and CeO2@CC cathode also displayed comparable results. It was ascertained that modification of NF/CF anode with PANI (conductive polymer) and CC cathode with CeO2 nanoparticles have significantly improved the overall MFC operational performance regarding tannery wastewater treatment and bioelectricity generation.

Assessing the impact of two conventional wastewater treatment plants on small streams with effect-based methods

Sixty percent of discrete surface water bodies in Europe do not meet the requirements for good ecological and chemical status and in Germany, the situation is even worse with over 90% of surface water bodies failing to meet the threshold. In addition to hydromorphological degradation, intensive land use and invasive species, chemical pollution is primarily considered to be responsible for the inadequate ecological status of the water bodies. As a quantitatively important source of micropollutants, wastewater treatment plants (WWTPs) represent an important entry path for chemical stressors. It is therefore important to analyze the effectiveness of the WWTPs in eliminating micropollutants and other chemical stressors to mitigate the negative impacts of the treated wastewater (WW) in aquatic ecosystems. Accordingly, in this study, we evaluated the impacts of two conventional, medium-sized WWTPs on their small receiving water systems in the southwestern region of Hessen in Germany during two sampling campaigns (spring and fall) using effect-based methods (EBM). We hypothesized that due to the insufficient elimination of micropollutants, a broad spectrum of toxic effects would be detected in conventionally treated WW and also in the receiving surface waters downstream the WWTPs. As EBMs a battery of in vitro assays and active biomonitoring using two in vivo assays were applied. The results supported our hypothesis and showed that the untreated WW had a very high baseline toxicity and also high endocrine and mutagenic activities. Conventional WW treatment, consisting of mechanical and biological treatment with nitrification, denitrification and phosphate precipitation, reduced baseline toxicity by more than 90% and endocrine activities by more than 80% in both WWTPs. Despite these high elimination rates, the remaining baseline toxicity, the endocrine, dioxin-like and mutagenic activities of the conventionally treated WW were so high that negative effects on the two receiving waters were to be expected. This was confirmed in the active monitoring with the amphipod Gammarus fossarum and the mudsnail Potamopyrgus antipodarum, as mortality of both species increased downstream of the WWTPs and reproduction in P. antipodarum was also affected. These results indicate that advanced WW treatment is needed to more effectively eliminate chemical stressors to prevent negative impacts of treated WW particularly in small receiving waters.

BIO-MITIGATION STUDIES OF ARTIFICIAL SWEETENER IN WASTE WATER: A REVIEW

Artificial sweeteners, which are widely used in modern diets and are persistent and may have negative effects on aquatic ecosystems, such as saccharin (SAC), cyclamate (CYC), aspartame (ASP), acesulfame (ACE), sucralose (SUC), alitame (ALT), neotame (NEO), and neohesperidin dihydrochalcone (NSDH), are being found in wastewater effluents at an increasing rate. In order to address this problem, bio-mitigation studies have shown promise as a method of reducing the harm that wastewater-borne artificial sweeteners do to the environment. This review provides a comprehensive overview of recent advancements in bio-mitigation approaches for artificial sweeteners in wastewater treatment systems. Firstly, the prevalence and persistence of artificial sweeteners in wastewater are discussed, highlighting their widespread occurrence and challenges associated with their removal during conventional wastewater treatment processes. Subsequently, various bio-mitigation strategies are examined, including microbial degradation, phytoremediation, and advanced oxidation processes. Microbial degradation, facilitated by diverse microbial communities, has shown potential for degrading artificial sweeteners into less harmful byproducts. several other techniques like Photocatalytic Degradation, Bank filtration, Granular activated carbon (GAC), advanced oxidation processes, such as ozonation and UV/H2O2 treatment, are explored for their ability to degrade artificial sweeteners into non-toxic compounds.

Comparative study of graphene oxide and copper oxide nanoparticle as surface modifiers in microfiltration membranes and adsorbents for efficient removal of textile dyes from contaminated water

Despite technological development, the textile industry still generates effluents with a high content of emerging contaminants, which are harmful to the environment. Conventional wastewater treatment methods struggle to remove emerging contaminants, necessitating advanced techniques. One promising solution is the modification of membranes and adsorption methods. The same modifying agents were used to modify the surface of microfiltration membranes and to create an adsorbent, allowing a comparison of the two processes in water treatment contaminated with dyes. Copper oxide nanoparticles were produced through green synthesis, and polyethersulfone microfiltration membranes were surface-modified using graphene oxide and copper oxide nanoparticles via a pressure-assisted method. Among the tested membranes, MF_GO1.0 + CuO3.0 showed the best performance, demonstrating a synergistic effect between the modifying agents, efficiently removing 97.69 % of Levafix Blue CA dye and recovering 84.88 % of the flux. It also exhibited outstanding removal rates (>99 %) for other textile dyes, such as Solophenyl Blue and Reactive Black 5. Membrane characterization revealed a decrease in contact angle for membranes modified with CuO and GO-CuO, rendering them more hydrophilic and improving permeability. Scanning Electron Microscopy depicted a compacted membrane, characteristic of graphene oxide, with nanoparticles on the surface. Chemical stability tests, conducted at neutral pH for 7 days, demonstrated no significant variation in permeability and contaminant removal. Although adsorption had limited effectiveness in removing the Levafix Blue CA dye, it provided valuable insights into the underlying mechanisms. Comparing membrane modification with adsorption, membranes displayed more efficiency in dye removal and showed enhanced antifouling properties. These results indicate the potential of modified membranes in treating dye-containing wastewater. As dye production increases, these innovative technologies offer promising solutions to reduce the environmental impact of textile industry effluents. By employing such advanced methods, we can work towards safeguarding our water resources and ecosystems from the harmful effects of textile wastewater pollution.

Multiple barriers as an efficient treatment for removing pesticides aiming direct potable reuse: A pilot scale study

Water reuse for potable purposes can represent a realistic source supply of drinking water in areas with water scarcity. Therefore, combining conventional wastewater treatment technologies with advanced technologies is necessary to remove contaminants and obtain high-quality and safe water. In this study, the pesticides and degradation products, atrazine (ATZ), hydroxyatrazine (ATZOH), deethylatrazine (DEA), deisopropylatrazine (DIA), simazine (SMZ), ametryn (AMT), diuron (DIU), 2,4-D, fipronil (FIP), fipronil sulfide (FIP-SF) and fipronil sulfone (FIP-SN) were evaluated in effluent after membrane bioreactor (MBR), effluent after advanced treatment by multiple barriers (MBR, reverse osmosis, UV/H2O2 and activated carbon), in tap water collected in the urban region of Campinas and in the Atibaia River (water supply source from city of Campinas). The pesticide concentrations in the Atibaia River and the post-MBR effluent ranged between 1 and 434 ng L−1 and 1 and 470 ng L−1, respectively. Therefore, the Atibaia River and the post-MBR effluent had the same magnitude pesticide concentrations. In the production of potable water reuse, after the multiple barriers processes, only fipronil (1 ng L−1) and atrazine (3 ng L−1) were quantified in some of the samples. In tap water from Campinas, atrazine, ATZOH, DEA, diuron, and 2,4-D were quantified in concentrations ranging between 3 and 425 ng L−1. Therefore, when comparing drinking water obtained from conventional treatment with potable water reuse, according to the pesticides studied, it is possible to conclude that the advanced treatment used on a pilot scale is promising for use in a potable water reuse plant. However, studies involving more microbiological and chemical parameters should be conducted to classify potable water reuse as drinking water.

Degradation of the neonicotinoid pesticide imidacloprid by electrocoagulation and ultrasound

Imidacloprid is still a widely used neonicotinoid insecticide that is banned in many countries because of the associated environmental risks. Due to the inefficiency of conventional wastewater treatments for pesticide removal, new treatment methods are being investigated. Electrochemical methods, including electrocoagulation (EC), seem to be promising alternatives considering their effectiveness in removing various pollutants from wastewater. The aim of this study was to investigate the effects of electrode material, current density, ultrasound, and operation time on the efficiency of imidacloprid removal from a model solution by EC. The combination of aluminum electrodes and 20 A of applied current for 20 min resulted in total imidacloprid degradation. A simplified energy balance was introduced as a form of process evaluation. Combining ultrasound with EC resulted in 7% to 12% greater efficacy than using only EC.

Four-in-one multifunctional self-driven photoelectrocatalytic system for water purification: Organics degradation, U(VI) reduction, electricity generation and disinfection against bacteria

This study addresses the energy-intensive nature of conventional wastewater treatment processes and proposes a solution through the development of a green, low-energy, and multifunctional wastewater treatment technology. The research focuses on a multifunctional self-driven photoelectrocatalytic (PEC) system, exploring its four-in-one applications in eliminating organic pollutants, reducing U(VI), generating electrical energy, and disinfecting pathogenic microorganisms. A TiO2-decorated carbon felt (CF@TiO2) cathode is synthesized to enhance interfacial charge transfer, with TiO2 coating improving surface binding sites (edge TiO and adsorbed -OH) for UO22+ adsorption and reduction. The self-driven PEC system, illuminated solely with simulated sunlight, exhibits remarkable efficiency in removing nearly 100 % of uranium within 0.5 h and simultaneously degrading 99.9 % of sulfamethoxazole (SMX) within 1.5 h, all while generating a maximum power output density (Pmax) of approximately 1065 μW·cm−2. The system demonstrates significant anti-interference properties across a wide pH range and coexisting ions. Moreover, 49.4 % of the fixed uranium on the cathode is reduced into U(IV) species, limiting its migration. The self-driven PEC system also excels in detoxifying various toxic organic compounds, including tetracycline, chlortetracycline, and oxytetracycline, and exhibits exceptional sterilization ability by disinfecting nearly 100 % of Escherichia coli within 0.5 h. This work presents an energy-saving, sustainable, and easily recyclable wastewater purification system with four-in-one capabilities, relying solely on sunlight for operation.

The fate and transport of neonicotinoid insecticides and their metabolites through municipal wastewater treatment plants in South China

Neonicotinoid insecticides (NEOs) have gained widespread usage as the most prevalent class of insecticides globally and are frequently detected in the environment, posing potential risks to biodiversity and human health. Wastewater discharged from wastewater treatment plants (WWTPs) is a substantial source of environmental NEOs. However, research tracking NEO variations in different treatment units at the WWTPs after being treated by the treatment processes remains limited. Therefore, this study aimed to comprehensively investigate the fate of nine parent NEOs (p-NEOs) and five metabolites in two municipal WWTPs using distinct treatment processes. The mean concentrations of ∑NEOs in influent (effluent) for the UNITANK, anaerobic–anoxic–oxic (A2/O), and cyclic activated sludge system (CASS) processes were 189 ng/L (195 ng/L), 173 ng/L (177 ng/L), and 123 ng/L (138 ng/L), respectively. Dinotefuran, imidacloprid, thiamethoxam, acetamiprid, and clothianidin were the most abundant p-NEOs in the WWTPs. Conventional wastewater treatment processes were ineffective in removing NEOs from wastewater (−4.91% to −12.1%), particularly major p-NEOs. Moreover, the behavior of the NEOs in various treatment units was investigated. The results showed that biodegradation and sludge adsorption were the primary mechanisms responsible for eliminating NEO. An anoxic or anaerobic treatment unit can improve the removal efficiency of NEOs during biological treatment. However, the terminal treatment unit (chlorination disinfection tank) did not facilitate the removal of most of the NEOs. The estimated total amount of NEOs released from WWTPs to receiving waters in the Pearl River of South China totaled approximately 6.90–42.6 g/d. These findings provide new insights into the efficiency of different treatment processes for removing NEOs in current wastewater treatment systems.

Separation of Cellulose from Wastewater and Valorisation via Pyrolysis: A Case Study in the Czech Republic

Currently, the recovery of resources from urban wastewater (WW) represents a priority. On this topic, the potential recovery of cellulose for its subsequent reuse in different sectors is gaining interest. In this work, a large-size conventional wastewater treatment plant (WWTP) was selected as a case study. A preliminary mechanical treatment was used, with the aim of separating, quantifying, and characterizing cellulose in WW. The results suggest that the per-capita production of dry primary cellulosic sludge (D-PCS) is equal to 1.46 ± 0.13 kgD-PCS PE−1 y−1, with an average calorific value of 21.04 MJ kg−1DM. Cellulosic fibres have an average length of >100 µm and a thickness of 2–5 µm. The D-PCS was subsequently treated via medium-temperature pyrolysis; a total of 29.5% of the initial D-PCS was converted into pyrolyzed primary cellulosic sludge (P-PCS) and only 26% into pyrolytic gas. More than 44.5% of the dried cellulose can be converted into pyrolytic oil. Moreover, three different scenarios of recovery have been considered, and the impact of cellulose separation in terms of COD fluxes entering the WWTP and potential energy recovery has been studied. The results suggested that, in this case study, the potential separation of the primary cellulosic sludge from the influent water flux would have no significant impact on COD load entering the biological treatments and biogas production in the anaerobic digestion of the secondary sludge.

Efficiency and costs of household filters for the retention of fibrous microplastics from the laundry process in Germany

Synthetic fiber fragments from household washing are one of many types of microplastics that enter the environment. The potential and costs of fiber retention, using filters, were modeled for Germany. The high costs indicate that synergistic measures for the simultaneous retention of different types of microplastics from other sectors, such as road traffic, should not be overlooked in terms of cost-effectiveness. Around 500 tons of microplastics enter the wastewater from washing machines every year, of which, around 91 % is removed by conventional wastewater treatment. The separation costs amount to approximately EUR 2.2 million per ton. The widespread use of filters already available on the market in households could increase the proportion removed to 96 %. The costs for the additional separation amount to approximately 114 million EUR per ton. The use of filters would increase the costs for household washing by approximately 37 %.A comparison with the separation of tire wear reveals synergy potential. Around 20,000 tonnes of microplastics from tire wear are subjected to conventional wastewater treatment in the same way as the fibrous microplastics from the washing process. One starting point, for example, is that both types of microplastics can bypass the wastewater treatment plants and enter the environment as so-called overflow if the wastewater network is overloaded. The potential to reduce the input of microplastics, by reducing the release through overflows, far exceeds the savings potential of individual measures such as the installation of filters in households.

A comparative study with vermifilter and geofilter for domestic wastewater treatment and its Phyto-toxicity efficacy

The present study investigated the role of earthworms in pollutant removal and toxicity assay of domestic wastewater. An indigenous reactor (vermigratings as an active layer) was set up for 60 days with a hydraulic loading rate of 1 m3 / m2 -d and hydraulic retention time of 3.5 h to evaluate its performance. Removal of total suspended solids, total dissolved solids, biochemical oxygen demand, chemical oxygen demand, and sulfate was found to be 92 %, 93 %, 89 %, 86 %, and 63.43 %, respectively. The Phyto-toxicity test reveals a higher germination rate and plant growth with vermifilter effluent than with geofilter effluent and raw wastewater. Additionally, vermifilter achieved heterotrophic bacteria removal by 1.54-fold. Hence, treated effluent can be used for irrigation purposes. Overall, this study will establish a potential alternative to the conventional wastewater treatment system and achieve Sustainable Development Goals 6.

Naturalization of treated wastewater by a constructed wetland in a water-scarce Mediterranean region

The effluents from conventional wastewater treatment plants (WWTP), even if accomplishing quality regulations, substantially differ in their characteristics with those of waters in natural environments. Constructed wetlands (CWs) serve as transitional ecosystems within WWTPs, mitigating these differences and restoring natural features before water is poured into the natural environment. Our study focused on an experimental surface-flow CW naturalizing the WWTP effluent in a semiarid area in Eastern Spain. Despite relatively low pollutant concentrations entering the CW, it effectively further reduced settled organic matter and nitrogen. Dissolved organic matter (DOM) reaching the CW was mainly protein-like, yet optical property changes in the DOM indicated increased humification, aromaticity, and stabilization as it flowed through the CW. Flow cytometry analysis revealed that the CW released less abundant but more active bacterial populations than those received. MiSeq Illumina sequencing highlighted changes in the prokaryotic community composition, with phyla Proteobacteria, Bacteroidetes, Firmicutes, and Actinobacteria dominating the CW outflow. Functional prediction tools (FaproTax and PICRUSt2) demonstrated a shift towards microbial guilds aligned with those of the natural aquatic environments, increased aerobic chemoheterotrophs, photoautotrophs, and metabolic reactions at higher redox potentials. Enhanced capabilities for degrading plant material correlated well with changes in the DOM pool. Our findings emphasize the role of CWs in releasing biochemically stable DOM and functionally suited microbial populations for natural receiving environments. Consequently, we propose CWs as a naturalization nature-based solution (NBS) in water-scarce regions like the Mediterranean, where reclaimed discharged water can significantly contribute to ecosystem's water resources compared to natural flows.