Conventional Microstrip Patch Antenna Research Articles

Development of an innovative patch antenna design and implementation using ENG materials for health care systems and 5G networks

The object of this study is a new design of an overhead microstrip antenna, including Epsilon Negative (ENG) metamaterials and L-shaped parasitic overlays aimed at achieving dual-band operation and improving the performance of modern wireless communication systems. The research is aimed at solving the problem of limited bandwidth and dual-band functionality in conventional antenna designs. This study solves the problem of limited bandwidth and dual-band functionality in conventional microstrip patch antenna designs, which are crucial for modern wireless communication systems. The inclusion of L-shaped parasitic overlays effectively expands the bandwidth in each frequency range. The results indicate significant improvements: at the upper resonant frequency, a 10 dB return loss bandwidth of 27.84 % (2.88–3.81 GHz) and a 3 dB axial ratio bandwidth of 5.05 % (2.90–3.05 GHz) are achieved, while at the lower resonant frequency, a return loss bandwidth is 10 dB, which is 6.11 % (2.22–2.36 GHz). These improvements indicate a significant increase in antenna performance compared to conventional designs, which is confirmed by comparing the simulation results with the measurement results. Distinctive features contributing to these results include the use of ENG metamaterials, which improve electromagnetic properties and signal propagation; vertical transitions, which provide efficient dual-band operation; and L-shaped parasitic overlays, which significantly expand bandwidth. These characteristics combine to eliminate the limitations of traditional designs, which makes the proposed antenna suitable for use in a wide frequency range in modern wireless communication systems.

Left Handed Metamaterials in Microstrip Patch Antenna Design: Miniaturization, Multiband Operation, and Improved Performance

The exotic electromagnetic properties of metamaterials (MTM) can be utilized to meet the increasing demand for smaller, lighter, and more compact multiband antennas. As the resonant frequency is dependent on the aperture parameters of the antenna, metamaterials allow for the miniaturization and performance enhancement of antennas. In this paper, two novel designs of metamaterial loaded microstrip patch antennas are proposed. The first structure emphasizes the miniaturization of patch antennas with performance improvements. The second one deals with the multiband operation of metamaterial loaded antennas with wider bandwidth and improved performance. Compared to the conventional microstrip patch antenna (MPA), the proposed metamaterial loaded antenna has reduced the size by 75%, and antenna characteristics have also improved significantly. The proposed metamaterial antenna resonates at 2.45 GHz, the return loss is -26 dB, and a gain of 5.28 dB is achieved. The multiband antenna can be realized by etching different numbers of complementary split ring resonators in the ground plane. The model proposed with three split ring resonators (SRR) at the ground plane shows quad band operations and can be used in S-band and C-band simultaneously. The quad-band antenna resonates at 3.04 GHz, 3.42 GHz, 5.35 GHz, and 6.08 GHz with bandwidths of 78 MHz, 93 MHz, 167 MHz, and 185 MHz, respectively. The antennas are designed on an FR-4 substrate with a permittivity of 4.3. Nicolson-Ross-Weir (NRW) method has been employed for the extraction and verification of the metamaterial properties of the unit cells. Due to its ability to capture more energy, the reported antenna can be used as a wireless device as well as an RF energy harvesting device. DUJASE Vol. 8 (1) 1-12, 2023 (January)

Slot-loaded Dual-Band Microstrip Patch Antenna for 5G and WLAN/WiMAX Wireless Applications

Objectives: This study introduces a dual-band rectangular microstrip patch antenna with a slot-loaded, specifically designed for 5G and WLAN/WiMAX applications. Method: The antenna is mounted on a substrate material of Rogers AD255C material having εr of 2.55 and a thickness of 1.56 mm. Three slots are etched on the conventional rectangular microstrip patch antenna. A 50-ohm microstrip line powers the antenna. The antenna that has been suggested is created and simulated using CST Studio Suite 2020. Findings: Based on numerical simulation, the proposed antenna functions at 3.5 GHz and 5.8 GHz, suitable for 5G and WLAN/WiMAX wireless technologies. The antenna offers measured return loss (S11) of -22.10 dB and -22.9 dB and a Gain of 4.43 dBi and 4.62 dBi at 3.5 GHz and 5.8 GHz, respectively. The radiation patterns are linear and broadside. Novelty: This article aims to create a smaller planer dual-band antenna that integrates WLAN/WiMAX and 5G communication standards into a single device. Keywords: Dual-band, 5G, WLAN, WiMAX, Microstrip patch antenna

Implanted Rhombus Ring Partial Inset-Fed Circularly Polarized Microstrip Monopole Antenna for WBAN Applications

In the present article, a design approach to accomplish circular polarization-based rhombus ring microstrip-fed monopole antenna working at 5.8 GHz for wireless body area network (WBAN) applications is proposed. The input impedance calculation using an electromagnetic theory of transmission line in a travelling wave coupled to the parallel-plate inductor model is conducted. Radiated electric field pattern calculation of the conventional square ring microstrip patch antenna (MSPA) using Biot and Savart’s law is reported. The circular polarization of the proposed antenna is accomplished by loading the radiating path with a capacitive element sectioned in the neighbourhood of the feed line. The proposed planar monopole antenna of volume 0.38λ0×0.38λ0×0.029λ0 (λ0 is evaluated at the resonant frequency of 5.8 GHz) achieves a -10 dB impedance bandwidth of 86.20% in the band (3-8 GHz) with a stable real gain of 8.29 dBic in circular polarization at the resonant frequency of 5.8 GHz and axial ration bandwidth of about 32.75% in the (5-6.9 GHz) band. Specific absorption rate (SAR) evaluation of the studied antenna is computed numerically on a part of the human phantom model to justify its use in WBAN applications. It is noted that the maximum amount of radiation absorbed by a part of the human phantom model is limited to a maximum SAR value of 1.45 W/kg and 0.754 W/kg on 1 g and 10 g of tissue mass, respectively. The prospective design has been fabricated and tested, and the experimental results are in good agreement with the simulation outcomes.

Circularly Polarized Polarization Conversion Metasurface-Inspired Antenna Array With Low RCS Over a Wide Band

A circularly polarized (CP) metasurface-inspired antenna array with low radar cross section (RCS) over a wideband based on polarization conversion metasurface (PCM) is proposed. Without increasing the structural complexity, the PCM units serve directly as antenna radiators, which not only maintains good radiation characteristics but also reduces both the in-band and out-of-band RCS of the antenna. Simulations show that the proposed PCM-inspired antenna array has an impedance bandwidth of 37.6% (8.2 to 12 GHz), a 3 dB axial ratio (AR) bandwidth of 32.5% (8.5 to 11.8 GHz), and a 3 dB gain bandwidth of 23.3% (9.5 to 12 GHz). The RCS of the proposed antenna array is greatly reduced for both polarizations in the frequency range of 7.6 to 16.2 GHz (72.3%) compared to conventional microstrip patch antenna array, with a maximum reduction of 20.6 dB. Moreover, the proposed PCM-inspired antenna array has a smaller element size compared to conventional low-RCS metasurface antennas, making it more conducive to the composition of a phased array. Finally, the proposed array is fabricated and measured, and the results confirm the simulations.

An Ultraminiature Circularly Polarized Microstrip Patch Antenna With MIM Capacitors

In this letter, an ultraminiature circularly polarized micostrip patch antenna is designed by four metal-insulator-metal (MIM) capacitors. First, four lumped capacitors are added to edge of the conventional microstrip patch antenna to conduct the simulation of the theoretical model for brevity. It is found that the micostrip patch antenna achieves electrically small ( <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">ka</i> <1) when the capacitors are selected carefully. In addition, the axial ratio and the resonance of the antenna can be optimized by the capacitors, which derives an effective method to design a compact circularly polarized antenna. Thus, four MIM capacitors are applied to replace the lumped capacitors to make the antenna physically realizable. A circularly polarized (CP) electrically small mictostrip patch antenna is designed, fabricated and measured to justify the effectiveness of the proposed method. The axial ratio bandwidth and the peak gain of the CP ( <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">ka</i> = 0.495) prototype achieves 0.88% and 4.25 dBiC, respectively. The size of the proposed antenna is only 0.104 λ <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">0</sub> ×0.104 λ <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">0</sub> .

Design of rectangular microstrip patch antenna with E-slot

The integration of an E-slot within the conventional microstrip patch antenna structure offers improved radiation characteristics and bandwidth. This research presents the design and analysis of a rectangular microstrip patch antenna with an E-slot. The proposed antenna is designed to operate at a specific frequency in the microwave range. The design process involves determining the dimensions of the rectangular patch, feedline, and E-slot to achieve the desired resonance frequency. The simulation and optimization are carried out using electromagnetic simulation software, considering the dielectric substrate properties and other relevant parameters. The E-slot is strategically placed within the patch structure to enhance the antenna's performance. It acts as an additional resonating element, contributing to increased bandwidth and improved radiation characteristics, such as gain and directivity. The integration of the E-slot modifies the current distribution on the patch, resulting in enhanced radiation properties. The performance of the proposed antenna is evaluated through various parameters, including return loss, radiation pattern, and bandwidth. Overall, the rectangular microstrip patch antenna with an E-slot presents a promising solution for achieving enhanced performance in terms of bandwidth and radiation characteristics. The proposed design opens up possibilities for further advancements in microstrip antenna technology, facilitating the development of an efficient and compact antenna structure for modern wireless applications.

Selection of Suitable Dielectric Substrate for Miniaturization of Microstrip Patch Antenna Using DGS Fractals

Background: Antennas size reduction with good performance characteristics is an essential part of designing a microstrip patch antenna (MPA) to select a suitable dielectric substrate. Methods: A conventional MPA is designed at 10GHz frequency, and later Minkowski fractal (1st iteration) defected ground structure (DGS) technique is applied for size reduction. The design is made to keep the radiation and reflection characteristics in contention. Results: A miniaturized MPA with 11% size reduction has been simulated using HFSS. The simulation results show the realization and selection of the substrate materials in the design process. Here, five different substrates are judiciously implemented and later compared. The comparison is made based on return loss, bandwidth, impedance, gain and efficiency Conclusion: We found a miniaturized MPA using the proposed first iteration of Minkowski fractal DGS. This MPA is suitable for X-band satellite communication and may be applied in government institutions, civil, military, monitoring weather, air traffic, defence tracking, maritime vessel traffic, etc., due to conformal and planar shape with reduced electrical length at 10GHz operating frequency

Novel Dual-Mode Polarization Insensitive Wide Angular Stable Circular Ring Based Deca-Band Absorber for RCS and EMI Shielding Applications

A simple concentric circular ring resonator-based nonreciprocal deca-band absorber is demonstrated in this article. The design primarily consists of two frequency selective surfaces (FSSs) among one is a compliment to the other printed on either side of the 2.4 mm thin FR-4 dielectric substrate. It exhibits near-unity absorption effectively at ten different resonant frequencies over X-Ka bands with an average absorption efficiency of 94.6%. Surface plasmonic resonances are the reason behind the multiband absorption and are illustrated with current profiles at resonant frequencies. The performance is angular stable for both transverse electric and transverse magnetic oblique incidences up to 60 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">o</sup> . The design is compact with a structural periodicity of 0.210 <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"><tex-math notation="LaTeX">${{\boldsymbol{\lambda }}}_{\boldsymbol{o}}$</tex-math></inline-formula> and thickness 0.07 <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"><tex-math notation="LaTeX">${{\boldsymbol{\lambda }}}_{\boldsymbol{o}}$</tex-math></inline-formula> , where <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"><tex-math notation="LaTeX">${{\boldsymbol{\lambda }}}_{\boldsymbol{o}}$</tex-math></inline-formula> is the lowest resonant peak's free-space wavelength. The 20×20 array of the design prototype is fabricated, and the measured results agree with the full-wave analysis. Bistatic radar cross section (RCS) analysis of the proposed absorber is evaluated along with a conventional microstrip patch antenna at <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">X</i> -band. Since the absorber design is based on complementary FSSs, it can also be utilized as a reflector for the not absorbing frequencies. The novelty lies in the utilization of the dual-side of the substrate made this design compact with a greater number of absorption peaks and good angular stability, making it potential for real-time RCS, and electromagnetic interference and shielding applications.

A Compact Wideband Filtering Antenna on Slots-Loaded Square Patch Radiator Under Triple Resonant Modes

In this article, a compact microstrip patch antenna (MPA) with enhanced bandwidth and filtering response is proposed and implemented solely by loading pairs of slots on the conventional square patch radiator. Initially, the dominant mode TM10 of the square patch radiator is theoretically investigated, revealing its broadside radiation pattern and its current flows in the consistent direction. After that, based on the regularities of field distribution, two pairs of slots are etched in the square patch so as to generate two extra modes without destroying both resonant and radiating properties of TM10 mode. By virtue of these two excited modes, two extra resonances are produced in proximity to its dominant one, so as to widen the bandwidth under triple resonant modes. Meanwhile, owing to the inverse equivalent magnetic currents (EMCs) along the radiation edges of the patch and the out-of-phase electric fields at the two sides of each slot under these two excited modes, radiation cancellation toward broadside direction and efficiency reduction occur simultaneously. Hence, radiation nulls are achieved in all direction, and particularly, the radiation null toward broadside direction is deeper than others. After our intensive investigation is done on the entire slots-loaded patch radiator, a wideband filtering MPA with three in-band resonances and two out-of-band radiation nulls has been finally constructed. For demonstration, a prototype antenna at a center frequency of 3.5 GHz is designed, fabricated, and measured. The measured results are found in good accordance with the simulated ones, demonstrating an impedance bandwidth of 9.14% with stable broadside realized gains as well as two radiation nulls at 3.12 and 3.83 GHz, respectively, in addition to its low profile of 0.029 free-space wavelength. Notably, the presented antenna has occupied the almost same area as the conventional square MPA, maintaining its good size compactness.

The Development of Broadband Microstrip Patch Antenna for Wireless Applications

The small volume of microstrip antennas has low production costs and easy production, which has accelerated the work in this area. The disadvantages are narrow bandwidth and low gain. In wireless communication, antennas with low return loss and high bandwidth are required. The bandwidth and power gain of the microstrip patch antennas should be increased optimally. This article presents the design of the broadband microstrip patch antenna operating in the ISM 2.4 GHz band (2400-2485 MHz). The study includes three-dimensional antenna model, simulation phase and fabrication / measurement phase. For the low cost of the antenna, FR-4 with the relative dielectric constant 4.3 and the loss tangent tan 0.02 is preferred as the substrate material. Dielectric material thickness is determined as 1.6 mm. The length of the feed line and the dimensions of the rectangular patch were found by mathematical calculations with the transmission line model. There are slots on the antenna, which is a very simple method in order to improve the bandwidth, gain and directivity parameters of the antenna. In the article, four different designs are presented, the results are compared and the proposed antenna has 979 MHz bandwidth and 2.68 dBi directivity gain at -10 dB at the resonance frequency of 2.316 GHz. The changes made in the antenna design have improved the results such as gain and bandwidth compared to the conventional microstrip patch antenna. The proposed antenna is suitable for use in mobile communication.

A miniaturized design of Vicsek snowflake-box fractal microstrip patch antenna using defective ground structure for wireless applications

AbstractIn this paper, miniaturization of fractal geometry with defected ground structure (DGC) concept has been experimentally verified at S-band (2–4) GHz. The design starts with a self-symmetry structure using conventional Vicsek snowflake-box fractal antenna. The same has been used in third iteration to achieve miniaturization. This proposed microstrip patch antenna (MPA) is resonating at 2.12 GHz with acceptable gain and broadside radiation. The miniaturization of about 87.26% when compared to conventional fractal MPA is achieved. The fractal unit cell is optimized for miniaturization and bandwidth by carrying out parametric study and applying the DGS shapes like rectangular and U-shaped slot etched in the ground plane of Vicsek snowflake-box fractal microstrip antenna. A fractal microstrip antenna is designed for wireless applications at 3.95 GHz. The fractal microstrip antenna is simulated using HFSS-V15 simulator. It is observed that the maximum size reduction of 87.26% is achieved in the third iteration of the Vicsek snowflake-box fractal radiating patch. The proposed fractal patch antenna is designed and fabricated using epoxy substrate of FR-4 with dielectric constant of 4.4 and thickness of 1.6 mm. The simulated results are compared with the measured results.

Design of a liquid crystal beam‐steerable antenna with characteristic mode analysis

A novel liquid crystal beam-steerable antenna is presented. It is a conventional liquid crystal microstrip patch antenna with a bending slot in the middle of the H-plane. Owing to the introduction of the bending slot, this antenna can work at even mode and odd mode within a frequency band. To obtain the resonant frequencies and radiation characteristics of the two modes, the method of characteristic mode analysis is utilised. It indicates that the resonant frequency of even mode is lower than that of odd mode. Therefore, by choosing liquid crystal as its substrate, this antenna can alter its operating modes by varying the permittivity of liquid crystal. Furthermore, beam steering can be realised since the radiation patterns of the two modes are divergent. An antenna prototype at Ka-band has been designed, fabricated and measured. The measured results show that the maximum radiation direction can scan from −30° to −2° continuously at 26.5 GHz in the H-plane.

Comparison of Metallization Schemes on Glass Dielectrics for X-Band Glass Antennas and Energy Harvesting.

We prepare and test four types of glass antennas for X-band applications and energy harvesting. These antennas are made of three different glass metallization schemes, including conductive copper foil (CCF), conductive silver paste (CSP) and indium tin oxide (ITO) thin film. Compared with conventional microstrip patch antennas, the dielectric substrate materials of these designs are replaced with silicon-boron glass (εr = 6, tangent δ = 0.002). The antenna with CCF as a radiator and ground plane (case one) is compared with the antenna with ITO replacing the radiator (case two) and ground plane (case three), respectively, and the glass antenna made of CSP (case four) is also presented. In this paper, these four types of glass antennas are measured and analyzed, and a comparison of the fabrication process and performance of these antennas is demonstrated. This study could contribute to the development of human-machine interactivity (HMI) systems with glass dielectric substrates.

Complementary split-ring resonator and strip-gap based metamaterial fractal antenna with miniature size and enhanced bandwidth for 5G applications

This paper proposes two different types of metamaterial (MTM) antennas for fifth-generation (5G) mid-band frequency operation. The radiating patch of the proposed antenna is based on the combined Minkowski-Sierpinski carpet fractal structure. On the ground plane, two different types of MTM structures: Complementary split-ring resonator (CSRR), and Strip-gap are etched to enhance the overall bandwidth and gain of the antenna. The introduction of these structures on the ground plane also leads to antenna miniaturization. Both the proposed MTM structure based antennas resonate at 3.5GHz. The overall size of the two fabricated prototypes is 28×29.5 mm2 / 28×28.5 mm2, which shows the compactness of the proposed design by 43% / 42% as compared to the conventional microstrip patch antenna (MPA). The measured bandwidth/gain achieved by the proposed combined Minkowski-Sierpinski carpet fractal antenna (CMSFA) having CSRR MTM and strip-gap etched on the ground plane are 370 MHz / 2.42dBi and 440 MHz / 3.75dBi, respectively.

A Wideband Triple-Mode Differentially Fed Microstrip Patch Antenna

A wideband differentially fed microstrip patch antenna (MPA) with triple-resonant modes is presented in this letter. The proposed triple-mode MPA is realized by combining two dual-mode MPAs (MPA-I and MPA-II) with different resonant frequency ratios. First, the TM <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">0,1</sub> mode and TM <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">0,1/2</sub> mode of dual-mode MPA-I can be concurrently excited by adding a pair of coupling shorted patches beside the strip MPA. The ratio of f <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">0,1/2</sub> /f <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">0,1</sub> can be easily adjusted by moving the shorting pins between the strip MPA and shorted patches. Second, by properly designing the dimensions of a conventional MPA, the TM <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">0,1</sub> and TM <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2,1</sub> modes of dual-mode MPA-II are simultaneously excited. To further reduce the ratio of f <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2,1</sub> /f <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">0,1</sub> , four slots are elaborately etched on the conventional MPA. Finally, by combining the two dual-mode MPAs, a triple-mode MPA with the frequency ratio of f <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">0,1/2</sub> :f <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2,1</sub> :f <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">0,1</sub> = 1.2:1.1:1 is realized. To verify the design concept, a prototype of triple-mode MPA was fabricated and measured. Experimental results show that the proposed microstrip antenna achieves a wide bandwidth of 26.5%, a low cross polarization of -23 dB, and high harmonic suppression.

Design and simulation of a novel 3-point star rectifying antenna for RF energy harvesting at 2.4 GHz

The rectenna as a device, is critical for achieving long-distance wireless power transfer. The centrality of this study is focused on adding to the collective knowledge of the subject matter, by providing a new perspective in terms of an alternative design for the antenna component of the rectenna. Essentially, this study features a novel “3-point star” design which was simulated in comparison with the conventional square microstrip patch antenna design. Both designs (i.e., operating at the Wi-Fi band 2.4 GHz), were assessed in terms of simulated performance parameters: gain, directivity, return loss, radiation pattern, and efficiency. From the simulation results, the proposed “3-point star” design, though slightly less efficient exhibited improved performance over the conventional square patch alternative, in terms of gain, directivity, and return loss. For the rectifying component, a greinacher voltage-doubler (with two HSMS2820 diodes), was designed separately and simulated over a range of input power levels (10dBm—34dBm), for 220-Ω, 380-Ω and 810-Ω load resistances, respectively. A maximum conversion efficiency of 88.02% was achieved at 28dBm for an 810 Ω load resistance. All design simulations were executed using Advanced Design System (ADS) software.

Ultra-širokopojasna planarna antena sa prorezom za buduće 5G primene na milimetarskim talasima

An ultra-wideband, compact planar antenna with defected ground structure (DGS) has been presented in this article for future 5G millimeter-wave applications. The proposed antenna overcomes the limitation of bandwidth of the conventional microstrip patch antenna (typically &lt; 5%). The antenna exhibits an ultra-wideband characteristic covering frequency band from 21.3 GHz to 40.6 GHz which makes the fractional bandwidth of 62.36%. The antenna performance is enhanced by etching slots on the patch and incorporating defect on the ground plane. The antenna achieves gain greater than 4.01 dBi and radiation efficiency greater than 95% throughout the operating band. In the given band it also exhibits very low cross-polarization level as well as stable radiation performance. This antenna is designed to operate in n257, n258, n260 and n261 5G millimeter-wave spectrum.

A Metamaterial Loaded Microstrip Patch Antenna for Lower 5G U-NII Spectrum

In this study, we have proposed a metamaterial loaded microstrip patch antenna for the sub-6 GHz range to operate in the Unlicensed National Information Infrastructure (U-NII) band. The Proposed Microstrip Patch Antenna (PMPA) has a U-shaped patch and an array of Complementary Split Ring Resonators (CSRR) in the ground plane. By adding a slot in the middle, the rectangular patch becomes a U-shaped one which is responsible for the enhancement of antenna bandwidth and gain. Our antenna provides a bandwidth of 392 MHz which is about 2.7 times larger compared to that of a Conventional Microstrip Patch Antenna (CMPA) of the same dimension. The maximum gain of our antenna is found 6.56 dB which is around 2 dB higher than that of the conventional one (4.72 dB). Due to the addition of the CSRR array in the ground plane, an improved impedance matching of 50 ohms has been achieved. The operating frequency range of the PMPA is from 5.525 to 5.917 GHz which can be used for 5G applications such as Wi-fi, Wi-Max, and IoT devices in the U-NII band.

Electrically Coupled Folded Arm Resonators with the Feedline Patch Antenna for Spurious Harmonic Suppression and Bandwidth Improvement

This paper presents a new design of the filtering antenna with a quasi-elliptic function response. The basic structure of the proposed filtering antenna is consists of a four-folded arms open-loop resonator (OLR). The proposed filtering antenna is simulated, improved and, analyzed by using 3D Computer Simulation Technology (CST) electromagnetic simulator software. The design has good spurious harmonic suppression in the upper and lower stopbands. The Insertion Loss of the proposed filtering antenna IL=0.2 dB and the Return Loss RL= -25.788 dB at the center frequency fo=5.75 GHz. The passband bandwidth which is relatively wide, and equal to 0.793 GHz. The microstrip filtering antenna circuit shows good design results compared to the conventional microstrip patch antenna. The filtering antenna design circuit with etched ground plane structure also has good design results compared to the filtering antenna design which has a complete ground plane structure.