Control Hydrogen Sulfide Research Articles

Indirect sulfur reduction via polysulfide contributes to serious odor problem in a sewer receiving nitrate dosage

Nitrate dosing is commonly used to control hydrogen sulfide production in sewer systems. However, quick rebound of the sulfide concentration after nitrate depletion has been observed and results in more serious odor and corrosion problem. To investigate the mechanism of sulfide regeneration in the nitrate-free period, a laboratory-scale sewer reactor was run for 30 days to simulate sulfide production and oxidation with intermittent nitrate addition. The results show that nitrate addition substantially reduced the sulfide concentration, but the produced elemental sulfur was then quickly reduced back to sulfide in nitrate-free periods. This induced more and more sulfide production in the sewer reactor. Elemental sulfur and polysulfide reductions were found in the sewage in nitrate-free periods, showing their contributions to the sulfide regeneration. Through batch tests, polysulfide was confirmed as the key intermediate for accelerating sulfur reduction during the nitrate-free period in the sewer. Sulfide production rates significantly increased by 65% and 59% in the presences of tetrasulfide and sulfur with sulfide, respectively, at the beginning of the test. While polysulfide formation was prevented by the ferrous chloride addition, the sulfur reduction rate remarkably decreased from 12.8 mgS/L-h to 1.8 mgS/L-h. This indicates that direct sulfur reduction was significantly slower than the indirect sulfur reduction via polysulfide; the latter process could be the cause for the quick rebound of the sulfide concentration in the sewer with intermittent nitrate dosing. Thus, the pathways of sulfur transformations in a sewer, both in the presence and absence of nitrate, were proposed. Microbial community analysis results reveal that some common sulfate-reducing bacteria (SRB) genera in sewer sediment were possible sulfur reducers. According to this finding, the effect and strategy of nitrate dosing for hydrogen sulfide control in sewers should be re-evaluated and re-considered.

Digester Gas Hydrogen Sulfide Control Using a Full-scale Biotrickling Filter at the Joint Water Pollution Control Plant

Digester Gas Hydrogen Sulfide Control Using a Full-scale Biotrickling Filter at the Joint Water Pollution Control Plant

Release and control of hydrogen sulfide during sludge thermal drying

The release of hydrogen sulfide (H2S) during sludge drying is a major environmental problem because of its toxicity to human health. A series of experiments were performed to investigate the mechanisms and factors controlling the H2S release. Results of this study show that: (1) the biomass and activity of sulfate-reducing bacteria (SRB) in sludge were the major factors controlling the amount of H2S release, (2) the sludge drying temperature had an important effect on both the extent and the timing of H2S release from the sludge, and (3) decreasing sludge pH increased the H2S release. Based on the findings from this study, a new system that integrates sludge drying and H2S gas treatment was developed, by which 97.5% of H2S and 99.7% of smoke released from sludge treatments was eliminated.

Emissions and Control of Hydrogen Sulfide at Landfills: A Review

Hydrogen sulfide (H2S) in landfill gas, formed with the biodegradation of municipal solid waste, is a major odorous component in a landfill. It poses a potential risk to humans and causes odor problems and complaints by the residents near landfills. Many studies have been conducted on landfill gas qualities. Also, various H2S control technologies have been used in different industrial sectors. However, comprehensive reviews on H2S issues in landfill gas are rare. An understanding of the formation of H2S encountered in landfill gas and the emission at which it occurs helps assess risk and problems. The authors review recent publications from different perspectives on H2S odor in landfills, including H2S generation the impact on the environment and human health, H2S levels in the landfill environment, and H2S control technologies at landfills.

Experimental Assessment of Water Sprays Utilization for Controlling Hydrogen Sulfide Releases in Confined Space

This paper reported the utilization of water spray for controlling H2S release in a confined space, which is especially important in industry. A typical spray tower was modified to simulate the confined space for people's enterable routine operation (e.g., pump room), in which the dilution capacity of water sprays can also be evaluated. This work consists of two parts: the first part focuses on the influences of different operating conditions on chemical dilution capacities of water sprays in mechanisms; the second one is comparison between two nozzle configurations for evaluating their feasibilities of practical application. Water sprays express eligible performance for H2S release control even though their dilution capacity was weakened at high gaseous concentrations and rates of releases. The presence of Na2CO3can significantly improve absorption effectiveness of H2S in water and the optimal Na2CO3additive was found to be 1.0 g·L−1in this test. Compared with Na2CO3, adjusting water flow rate may be an effective strategy in enhancing dilution capacity of water sprays due to the fact that larger flow rate led to both less dilution time (TD) and dilution concentration (CD). Furthermore, multinozzle configuration is more efficient than single-nozzle configuration under the same water consumption.

Application of a long-lasting colloidal substrate with pH and hydrogen sulfide control capabilities to remediate TCE-contaminated groundwater

A long-lasting emulsified colloidal substrate (LECS) was developed for continuous carbon and nanoscale zero-valent iron (nZVI) release to remediate trichloroethylene (TCE)-contaminated groundwater under reductive dechlorinating conditions. The developed LECS contained nZVI, vegetable oil, surfactants (Simple Green™ and lecithin), molasses, lactate, and minerals. An emulsification study was performed to evaluate the globule droplet size and stability of LECS. The results show that a stable oil-in-water emulsion with uniformly small droplets (0.7μm) was produced, which could continuously release the primary substrates. The emulsified solution could serve as the dispensing agent, and nZVI particles (with diameter 100–200nm) were distributed in the emulsion evenly without aggregation. Microcosm results showed that the LECS caused a rapid increase in the total organic carbon concentration (up to 488mg/L), and reductive dechlorination of TCE was significantly enhanced. Up to 99% of TCE (with initial concentration of 7.4mg/L) was removed after 130 days of operation. Acidification was prevented by the production of hydroxide ion by the oxidation of nZVI. The formation of iron sulfide reduced the odor from produced hydrogen sulfide. Microbial analyses reveal that dechlorinating bacteria existed in soils, which might contribute to TCE dechlorination.

The Research on Influence Factors and Control of Hydrogen Sulfide during Steam Drive

This project carries out the research on influence factors of wells producing hydrogen sulfide in connection with the actual situation of producing hydrogen sulfide in Qi-40 steam drive process. Experimental studies have shown that: A. temperature is the main external factors of produce hydrogen sulfide, It will produce hydrogen sulfide when temperature is above 100°C, hydrogen sulfide content increase about 300ppm in average when the temperature increase per 20°C; hydrogen sulfide content will be in the greatest increase when temperature at the range of 160°C~180°C; the rate of increase in the levels of hydrogen sulfide will significantly reduce when temperature above 180 °C.B. Adding Chemical agent with surface activity can inhibit the release of hydrogen sulfide. C. Adding acid chemical agent will make the content of hydrogen sulfide increase. The experimental study also investigated hydrogen sulfide prevention measures.

Characterization of recycled rubber media for hydrogen sulphide (H2S) control

Hydrogen sulphide (H2S) adsorption capacities on recycled rubber media, tyre-derived rubber particle (TDRP™), and other rubber material (ORM™) have been evaluated. As part of the research, densities, moisture contents, and surface properties of TDRP™ and ORM™ have been determined. The research team findings show that TDRP™ and ORM™ are more particulate in nature and not highly porous-like activated carbon. The characteristics of surface area, pore size, and moisture content support chemisorption on the macrosurface rather than physical adsorption in micropores. For example, moisture content is essential for H2S adsorption on ORM™, and an increase in moisture content results in an increase in adsorption capacity.

Intensified nitrogen and phosphorus removal in a novel electrolysis-integrated tidal flow constructed wetland system

A novel electrolysis-integrated tidal flow constructed wetland (CW) system was developed in this study. The dynamics of intensified nitrogen and phosphorus removal and that of hydrogen sulphide control were evaluated. Ammonium removal of up to 80% was achieved with an inflow concentration of 60 mg/L in wetland systems with and without electrolysis integration. Effluent nitrate concentration decreased from 2 mg/L to less than 0.5 mg/L with the decrease in current intensity from 1.5 mA/cm2 to 0.57 mA/cm2 in the electrolysis-integrated wetland system, thus indicating that the current intensity of electrolysis plays an important role in nitrogen transformations. Phosphorus removal was significantly enhanced, exceeding 95% in the electrolysis-integrated CW system because of the in-situ formation of a ferric iron coagulant through the electro-dissolution of a sacrificial iron anode. Moreover, the electrolyzed wetland system effectively inhibits sulphide accumulation as a result of a sulphide precipitation coupled with ferrous-iron electro-dissolution and/or an inhibition of bacterial sulphate reduction under increased aerobic conditions.

A8.8 Controllable hydrogen sulfide donors and their anti-inflammatory potential in the murine macrophage cell line RAW264.7

Background and ObjectivesHydrogen sulfide (H2S) is a newly discovered gaseous signalling molecule like CO and NO and plays an important role in many physiological and/or pathological processes. Modulation of H2S...

Utilization of the used tire rubber particle in hydrogen sulfide control

The adsorption capacity of fine rubber particle media (FRPM) derived from discarded vehicle tires and the consumer wasted rubber sources was evaluated for hydrogen sulfide treatment. H2S breakthrough tests were performed at various zinc contents, temperatures, and packing quantities. High zinc concentrations increased the adsorption capacity of FRPM significantly. H2S removal by FRPM was optimized at a packing quantity of 75 % of the column volume, and the adsorption capacity increased with reactor temperature within the range of 20–85 °C. The regeneration of ZnCl2 solution was reliable for increasing regeneration capacity of the FRPM-adsorbed H2S. FRPM seems to be an attractive alternative of H2S adsorbents in terms of cost effectiveness compared to traditional materials.

Controllable Hydrogen Sulfide Donors and Their Activity against Myocardial Ischemia-Reperfusion Injury

Hydrogen sulfide (H2S), known as an important cellular signaling molecule, plays critical roles in many physiological and/or pathological processes. Modulation of H2S levels could have tremendous therapeutic value. However, the study on H2S has been hindered due to the lack of controllable H2S releasing agents that could mimic the slow and moderate H2S release in vivo. In this work we report the design, synthesis, and biological evaluation of a new class of controllable H2S donors. Twenty-five donors were prepared and tested. Their structures were based on a perthiol template, which was suggested to be involved in H2S biosynthesis. H2S release mechanism from these donors was studied and proved to be thiol-dependent. We also developed a series of cell-based assays to access their H2S-related activities. H9c2 cardiac myocytes were used in these experiments. We tested lead donors' cytotoxicity and confirmed their H2S production in cells. Finally we demonstrated that selected donors showed potent protective effects in an in vivo murine model of myocardial ischemia-reperfusion injury, through a H2S-related mechanism.

Effects of nitrate dosing on methanogenic activity in a sulfide-producing sewer biofilm reactor

Nitrate dosing is widely used by water industry to control hydrogen sulfide production in sewers. This study assessed the impact of nitrate addition on methane generation by sewer biofilms using a lab-scale rising main sewer reactor. It was found that methanogenesis could coexist with denitrification and sulfate reduction in sewers dosed with nitrate. However, methane production was substantially reduced by nitrate addition. Methanogenic rates remained below 10% of its baseline level, with 30 mg-N/L of nitrate dosing for each pump event. By calculating the substrate penetration depth in biofilms, it is suggested that methanogenesis may persist in deeper biofilms due to the limited penetration of nitrate and sulfate, and better penetration of soluble organic substrates. The control of methane and sulfide production was found to be determined by the nitrate penetration depth in biofilms and nitrate presence time in sewers, respectively. The presence of nitrous oxide after nitrate addition was transient, with a negligible discharge of nitrous oxide from the sewer reactor due to its further reduction by denitrifiers after nitrate depletion.

Assessment of Effects of Chronic Hydrogen Sulfide Poisoning on Cytochrome P450 Isoforms Activity of Rats by Cocktail Approach

Hydrogen sulfide (H₂S) is one of the neurotoxic gases with suffocating and irritating. Its main target organs of toxic effects are the central nervous system and respiratory system. Cocktail method was used to evaluate the influence of chronic hydrogen sulfide poisoning on the activities of cytochrome P450 (CYP450) isoforms CYP1A2, CYP2C9, CYP2B6 and CYP2D6, which were reflected by the changes of pharmacokinetic parameters of 4 specific probe drugs phenacetin, tolbutamide bupropion and metroprolol, respectively. The experimental rats were randomly divided into two groups, control group and chronic hydrogen sulfide poisoning group. The chronic hydrogen sulfide poisoning group rats were inhaled 20 ppm for 1 h twice a day for 40 d. The mixture of 4 probes was given to rats through sublingual veins and the blood samples were obtained at a series of time-points through the caudal vein. The concentrations of probe drugs in rat plasma were measured by liquid chromatography-mass spectrometry (LC-MS). In the experiment for chronic hydrogen sulfide poisoning and control group, there was a statistically significant difference in the area under the plasma concentration-time curve from zero to infinity (AUC(0-∞)), plasma clearance (CL) and maximum plasma concentration (C(max)) for phenacetin and bupropion, while there was no statistical pharmacokinetics difference for tolbutamide and metoprolol. Chronic hydrogen sulfide poisoning could induce the activity of CYP1A2 and CYP2B6 of rats.

Effects of hydrogen sulphide in an experimental model of renal ischaemia–reperfusion injury

Renal ischaemia-reperfusion injury (IRI) is a major cause of acute renal failure and renal transplant dysfunction. The aim of this study was to investigate the efficacy of the endogenous gaseous signalling molecule hydrogen sulphide in protecting against renal IRI. Large White female pigs underwent laparotomy and cross-clamping of the left renal pedicle for 60 min. Animals were allocated randomly to treatment with either intravenous hydrogen sulphide (n = 6) or saline control (n = 6) 10 min before clamp release, and then underwent a right nephrectomy. Staff were blinded to treatment allocation and animals were recovered for 7 days. Hydrogen sulphide therapy resulted in a marked reduction in kidney injury with reduced serum creatinine levels on days 1-5, in a reduced area under the creatinine-time curve, and a halving of the time to achieve a creatinine level of less than 250 µmol/l, compared with the control. Hydrogen sulphide also preserved glomerular function, as shown by the urinary protein/creatinine ratio, which, compared with baseline, increased on days 1 and 3 in the control group (mean(s.e.m.) 3·22(1·43), P = 0·016 and 2·59(1·27), P = 0·031), but not in the treatment group (0·99(0·23), P = 0·190 and 1·06(0·44), P = 0·110, respectively). Mean(s.e.m.) tumour necrosis factor α levels at 6 h postreperfusion increased in the control animals (56(6) versus 115(21) pg/ml; P = 0·026), but not in the hydrogen sulphide-treated animals (61(7) versus 74(11) pg/ml; P = 0·460). Renal neutrophil infiltration at 30 min (myeloperoxidase staining) was also significantly reduced by treatment with hydrogen sulphide (P = 0·016). Hydrogen sulphide offers a promising new approach to ameliorating renal IRI with potential translation into a number of clinical settings, including renal transplantation.

Evaluation of hydrogen sulphide concentration and control in a sewer system

This study focused on monitoring hydrogen sulphide (dissolved and atmospheric) generation and wastewater volumetric flow in a 21.4 km sewer line of the City of San Antonio, Texas. The results were used to evaluate daily and seasonal trends of atmospheric and dissolved sulphide, and to better apply sulphide control using ferrous sulphate to prevent odour and sewer pipe deterioration. As part of this study, the evaluation of a cost-effective dosing strategy with ferrous sulphate was performed to better control the sulphide contents in wastewater. Dosing studies were performed in the laboratory to find the required ratio of ferrous sulphate for acceptable sulphide removal. The results indicate a 1.25 mole ratio requirement, to reduce sulphide by 93%. Over a typical daily diurnal cycle, necessary dosing rates to maintain sulphide concentrations below 2 mg varied between 0 and 36,777 mol d−1 with a daily average rate of 14,438 mol d−1. If, instead of dosing at the maximum required rate, dosing was matched over the diurnal cycle, chemical savings would amount to 22,339 mol d−1 while achieving sulphide control. The approximate cost of the ferrous sulphate solution dosed is $0.14 per mol and this amount of chemical savings translates into roughly $2923 per day. Actual dosing cost for the hypothetical average day will be $1889 per day. These cost savings can easily recoup the required instrumentation costs to achieve this diurnal dose matching.

Plant Pathogenic Bacteria Utilize Biofilm Growth-associated Repressor (BigR), a Novel Winged-helix Redox Switch, to Control Hydrogen Sulfide Detoxification under Hypoxia

Winged-helix transcriptional factors play important roles in the control of gene expression in many organisms. In the plant pathogens Xylella fastidiosa and Agrobacterium tumefaciens, the winged-helix protein BigR, a member of the ArsR/SmtB family of metal sensors, regulates transcription of the bigR operon involved in bacterial biofilm growth. Previous studies showed that BigR represses transcription of its own operon through the occupation of the RNA polymerase-binding site; however, the signals that modulate its activity and the biological function of its operon are still poorly understood. Here we show that although BigR is a homodimer similar to metal sensors, it functions as a novel redox switch that derepresses transcription upon oxidation. Crystal structures of reduced and oxidized BigR reveal that formation of a disulfide bridge involving two critical cysteines induces conformational changes in the dimer that remarkably alter the topography of the winged-helix DNA-binding interface, precluding DNA binding. This structural mechanism of DNA association-dissociation is novel among winged-helix factors. Moreover, we demonstrate that the bigR operon is required for hydrogen sulfide detoxification through the action of a sulfur dioxygenase (Blh) and sulfite exporter. As hydrogen sulfide strongly inhibits cytochrome c oxidase, it must be eliminated to allow aerobic growth under low oxygen tension, an environmental condition found in bacterial biofilms, xylem vessels, and root tissues. Accordingly, we show that the bigR operon is critical to sustain bacterial growth under hypoxia. These results suggest that BigR integrates the transcriptional regulation of a sulfur oxidation pathway to an oxidative signal through a thiol-based redox switch.

Dynamic microbial response of sulfidogenic wastewater biofilm to nitrate

Nitrate is one of the chemicals often added to wastewater to control hydrogen sulfide production by sulfate-reducing bacteria (SRB). While the effect of nitrate in various SRB pure cultures is well documented, the effect observed in mixed microbial communities is not consistent. This study investigates the response of mixed SRB communities to nitrate, by examining the changes in activity and community composition of sulfidogenic wastewater biofilm over a 10-day period with 10 mmol L(-1) nitrate exposure. Biofilms were enriched in SRB belonging to the Desulfobacter, Desulfobulbus, Desulfomicrobium, and Desulfovibrio genera. Nitrate exposure decreased dsrB transcription within 4 h, and sulfate consumption within 10 days, but it did not fully eliminate sulfide production in the biofilms. The effect of nitrate on SRB was genus specific; Desulfobacter and Desulfobulbus disappeared while Desulfovibrio and Desulfomicrobium persisted in the biofilms. Nitrate exposure also led to the rapid proliferation of nitrate-reducing bacteria within the biofilms, and increased the biofilm thickness. Nitrate consumption began within 2 h of nitrate exposure and gradually increased in rate over time. Transcription of the nitrate reductase napA, and the diversity of nitrate reductase genes narG and napA also increased concurrently. Our results demonstrate that some SRB, presumably those able to tolerate or detoxify nitrite, will persist in sulfidogenic wastewater biofilms despite continuous exposure to high levels of nitrate. Nitrate is therefore unlikely to provide lasting hydrogen sulfide suppression in wastewater biofilms harboring Desulfovibrio or Desulfomicrobium populations.

Inhibitory effects of enterococci on the production of hydrogen sulfide by hydrogen sulfide-producing bacteria in raw meat

Applying competitive exclusion micro-organisms to control hydrogen sulfide (H₂S) gas produced by hydrogen sulfide-producing bacteria (SPB) in chicken meat. Five SPB strains, isolated from animal by-products, were used for screening lactic acid bacteria (LAB) that can inhibit the production of H₂S by SPB in trypticase soy broth supplemented with L-cysteine (TSB-L-cys). A sensitive and accurate test strip method was developed for H₂S determination in real time. One LAB strain, isolate L86, from cheese whey, demonstrated the highest inhibitory activity against the production of H₂S by SPB. The isolate L86 was confirmed as Enterococcus faecium that does not possess genes encoding for vancomycin resistance based on PCR analysis. Enterococcus faecium strain L86 reduced (P < 0·05) the yield of H₂S upto 51·2% in 10 h at 35°C in TSB-L-cys medium. In fresh chicken meat, the yield of H₂S produced by the artificially inoculated SPB was reduced (P < 0·05) by 48·6, 49·7 and 69·8% in 10 h at 35, 30 and 25°C, respectively. Enterococcus faecium strain L86 also reduced (P < 0·05) by 53·8% on the yield of H₂S produced by the indigenous SPB in partially spoiled chicken meat at 35°C for 10 h. Enterococcus faecium strain L86 is effective on inhibiting the production of H₂S by SPB. The application of this biological agent to raw animal by-products will provide a safer working environment in rendering processing plants and produce higher-quality rendered products.

Estimating and Controlling Hydrogen Sulfide in Municipal Interceptors from a High Strength, High Temperature Industrial Wastewater

Estimating and Controlling Hydrogen Sulfide in Municipal Interceptors from a High Strength, High Temperature Industrial Wastewater