Continuous Flow Research Articles

Fresh cement as a frictional non-Brownian suspension

Cement is an essential construction material due to its ability to flow before later setting, however the rheological properties must be tightly controlled. Despite this, much understanding remains empirical. Using a combination of continuous and oscillatory shear flow, we compare fresh Portland cement suspensions to previous measurements on model non-Brownian suspensions to gain a micro-physical understanding. Comparing steady and small-amplitude oscillatory shear, we reveal two distinct jamming concentrations, ϕμ and ϕrcp, where the respective yield stresses diverge. As in model suspensions, the steady-shear jamming point is notably below the oscillatory jamming point, ϕμ<ϕrcp, suggesting that it is tied to frictional particle contacts. These results indicate that recently established models for the rheology of frictional, adhesive non-Brownian suspensions can be applied to fresh cement pastes, offering a new framework to understand the role of additives and fillers. Such micro-physical understanding can guide formulation changes to improve performance and reduce environmental impact.

Artificial intelligence (AI) inspired an innovative approach for real-time flow measurements – water distributions at outlets, in Punjab province Pakistan

Abstract Accurate water metering is essential for effective water management, especially for measured and equitable distribution of canal flows, most imperative in Pakistan. The inflows distributed through outlets must adhere to pre-designated levels, defined by Punjab Irrigation Department from head to tail. With recent channels lining, the outlets’ sanctioned flow is found changed requiring adjustments. Furthermore, there is a lack of reliable mechanisms for continuous flow regulations, resulting in unmanaged distributions. The focus of the reported work was on precise and real-time discharge monitoring at outlets using a newly developed device utilizing artificial intelligence. During validation training, a strong agreement was observed, and all evaluation parameters supported the device accuracy for measurements. In detailed studies of canal operations, the sanctioned discharges of individual outlets along selected distributaries were found significantly inequitable. Out of 162 outlets, 42 were suspended for being unmanaged, with tail users receiving ≤50% of their fair intakes. Additionally, there were instances of massive irrational supplies exceeding 200% of allocated discharges. The developed device has the potential to accurately measure real-time discharges for managed distributions. Conclusively, the challenging task of fair and equity-based discharge allocations, in conjunction with the Warabandi system, necessitates the reevaluation of the allocated flow quantity at each outlet.

Continuous kinetics of 2-hydroxyisobutryic acid esterification using solid acid granular and monolithic activated carbon catalysts

Kinetics of 2-hydroxyisobutyric acid (2-HIBA) esterification with ethanol was studied using sulfonated carbon catalysts in granular (sGAC) and monolith (sACM) forms in a continuous flow packed bed reactor. 2-HIBA is a potential biobased carboxylic acid and its ester a sustainably produced industrial solvent. The catalyst monolith form, made from renewable carbon, offers significantly higher space time yields and conversions, yet little kinetic data or models are available for its use, especially under non-ideal conditions. The effect of ethanol/2-HIBA molar ratio (44, 10, 3.6 and 1.5) at different liquid residence times (3–9 min) was investigated using sGAC. Kinetics of sACM esterifications were investigated at a molar ratio of 3.6 by varying the residence time (2–7 min) and compared with the sGAC. The sACM displayed higher ester yields, acid conversions, and significantly higher reaction rates and space–time-yields (2.1–2.8 ×) compared to the sGAC due to higher surface area to volume ratio. The sACM reaction rates and turnover frequency were comparable to solid acid resins and sulfated silica and zirconia. Pseudo-homogeneous, Eley-Rideal and Langmuir-Hinshelwood models were applied to fit the kinetic data, and the reaction system parameters were obtained through regression analysis. The LH dual active site model resulted in the lowest mean relative error for both 2-HIBA and ester concentration residuals. Adsorption/desorption equilibrium constants for 2-HIBA, ethanol, and ester, were higher compared to water suggesting hydrophobic regions in the sGAC/sACM. Estimation of the external and internal mass transfer criteria indicated negligible effects of mass transfer. With further development sACM and the kinetic model can be used for reactor design of continuous esterification processes using solid acid monolith catalysts.

Startup characteristics of the large length–diameter ratio high-temperature heat pipe

Large length–diameter ratio high-temperature sodium heat pipes (HTSHPs) are uniquely structured heat-transfer devices with significant application potential in high-temperature solar thermal power and small-scale nuclear systems. This study tested HTSHPs' startup characteristics examining various parameters. Results indicate that the transition temperature for flow transition is 564 K, and the continuous flow transition temperature is 722 K. Heat pipes at 15 % fill ratio are adaptable across various inclination angles, whereas those at 25 % and 35 % fill ratios show optimal startup at smaller angles (15°, 30°), with decreasing startup time as angle increases, notably significant at 45°.The start-up time refers to the duration from the initiation of heating to the point when all the normal operational temperature points of the HTSHP reach the continuous flow transition temperature during the condensation section. During the experiments, heat pipes with a large length–diameter ratio exhibit heat transfer instability, temperature oscillation and local overheating. Reducing the fill ratio and inclination angle effectively reduces the probability of temperature oscillation and local overheating. This study proposes a novel method for optimizing temperature oscillations in heat pipe design, offering pioneering insights and experimental data crucial for specialized high-temperature heat pipe research.

Continuous flow synthesis of hierarchical low silica X zeolite

Zeolites, renowned for their versatile applications in catalysis, adsorption, and ion exchange, have long been synthesized using conventional batch processes. However, the inherent limitations of these methods, such as resource-intensive conditions and inconsistent product quality, underscore the need for a sustainable and efficient approach. In this study, a continuous flow synthesis process was established for the synthesis of industrially important low silica X (LSX) zeolite using a tubular reactor. The synthesis gel was subjected to aging for 5 days at room temperature to facilitate nucleation and crystal growth combined with the fast-heating rate in a tubular reactor at 363 K & 1.1 atm., which in turn produces LSX after 40 min. The synthesized product was confirmed by the XRD, FE-SEM, EDS, XRF, TEM, and N2 adsorption-desorption; the data was compared with the LSX sample synthesized by batch process. The result implies that LSX prepared by continuous flow has a pure phase of LSX with the hierarchical structure, which provides better adsorption capacity of CO2 at 298 K up to 20 bar. Due to continuous flow synthesis, the crystallization time was reduced and faster kinetics which may be helpful for scale-up the process for LSX synthesis.

WLI, XPS and SEM/FIB/EDS Surface Characterization of an Electrically Fluted Bearing Raceway

Electrical bearing currents may disturb the performance of the bearings via electro-corrosion if they surpass a limit of ca. 0.1 to 0.3 A/mm2. A continuous current flow, or, after a longer time span, an alternating current or a repeating impulse-like current, damages the raceway surface, leading in many cases to a fluting pattern on the raceway. Increased bearing vibration, audible noise, and decreased bearing lubrication as a result may demand a replacement of the bearings. Here, an electrically corroded axial ball bearing (type 51208) with fluting patterns is investigated. The bearing was lubricated with grease lubrication and was exposed to 4 A DC current flow. It is shown that the electric current flow causes higher concentrations of iron oxides and iron carbides on the bearing raceway surface together with increased surface roughness, leading to a mixed lubrication also at elevated bearing speeds up to 1500 rpm. The “electrically insulating” iron oxide layer and the “mechanically hard” iron carbide layer on the bearing steel are analysed by WLI, XPS, SEM, and EDS. White Light Interferometry (WLI) is used to provide an accurate measurement of the surface topography and roughness. X-ray Photoelectron Spectroscopy (XPS) measurements are conducted to analyze the chemical surface composition and oxidation states. Scanning Electron Microscopy (SEM) is applied for high-resolution imaging of the surface morphology, while the Focused Ion Beam (FIB) is used to cut a trench into the bearing surface to inspect the surface layers. With the Energy Dispersive X-ray spectrometry (EDS), the presence of composing elements is identified, determining their relative concentrations. The electrically-caused iron oxide and iron carbide may develop periodically along the raceway due to the perpendicular vibrations of the rolling ball on the raceway, leading gradually to the fluting pattern. Still, a simulation of this vibration-induced fluting-generation process from the start with the first surface craters—of the molten local contact spots—to the final fluting pattern is missing.

Ultrafast and efficient continuous flow organic synthesis with a modified extruder-grinder system

The study introduces a groundbreaking continuous system that combines an extruder and grinder to enable catalyst-free and solvent-free reactions under mild conditions. This temperature-controlled system facilitates the synthesis of highly functionalized chromenes, which have valuable applications in generating combinatorial libraries and complex target molecules. The newly developed mill extruder machine offers several advantages for industrial production on a large scale. It effectively reduces waste, saves energy, and enhances time efficiency. This system represents a significant advancement in the field, providing a new strategy for one-pot synthesis of various types of highly functionalized spirooxindoles and chromenes. Remarkably, these reactions can be accomplished within a short timeframe of 2–10 min, yielding impressive results of 75–98%. The results demonstrate superior performance compared to traditional reaction methods, making it an appealing tool and hotspot area of research in green chemistry.

Gas-liquid-soild triphasic continuous flow microreactor for improving homogeneous distribution of solid composites in heterogeneous photocatalytic degradation progress

The homogeneous distribution of solid composites in continuous flow photocatalytic progress is difficult due to the settle and clog in capillary. To overcome this challenge, a gas–liquid-soild triphasic continuous flow photoreactor was designed and used for heterogeneous photocatalytic degradation of antibiotics wastewater. In this work, take Bi2WO6 as photocatalyst, photocatalytic degradation of ofloxacin wastewater was studied systematically under different operational parameters and flow characteristics. The photocatalytic degradation performance of flow photoreactor was superior to batch counterpart, especially in later stage of reaction. The apparent reaction rate constants (k) of flow photoreactor was about 1.6 times that of batch counterpart. The gas–liquid mass transfer coefficient of flow photoreactor was more than 25 times that of batch photoreactor. Moreover, the influence mechanism of gas fraction, flow rate and tube diameter on photocatalytic degradation performance was investigated under various continuous flow conditions. Higher gas fraction, faster flow rate and smaller tube diameter were beneficial to improve photocatalytic degradation performance due to the enhancement of irradiation transmission and intensification of mass transfer. Therefore, the results of this work provided a guideline for the application of gas–liquid-soild triphasic continuous flow photocatalytic degradation technology in the future.

An initial study of cell separation based on mechanical properties using a sponge-like monolithic polymer

We developed a novel cell separation method based on the mechanical properties using a sponge-like monolithic polymer (SPM) in a spin-column format capable of high throughput and mass processing for cell diagnosis and separation. The continuous large flow pores of the monolithic skeleton around 200 μm were expected to act as a sieving matrix for large flexible molecules such as cells larger than 10 μm in diameter, based not only on the size but also on the mechanical deformability of the cells. The passage rates of rigid polystyrene beads ranging in size from 1 to 10 μm were investigated and demonstrated that the spin column acted as a separation matrix rather than a size-based cut-off filter in the 60 and 200 μm pores of the SPM. Two cell types, adherent cells (HeLa cells) and suspension cells (THP-1 cells), showed different passage behavior in the spin column, and 70 % and 30 % of the cells, respectively, were trapped in the column and never eluted. To investigate how the mechanical deformability of the cells affects the passage behavior, glutaraldehyde treatment, which denatured the proteins and changed the elastic moduli, was performed and compared. As a result, the fixed cells drastically reduced the passage rate and became trapped inside the SPM column. These initial studies explored a new application field of SPM for high throughput cell separation based on the mechanical properties of the cells despite the same size, and contribute to a new cell assay method prior to cell transplantation.

Sweat and microwave manageable textiles for efficient personal thermal comfort and electromagnetic radiation defend

Although electromagnetic interference (EMI) shielding fabrics integrated with absorption and reflection have recently shown attractive defense performance, effective sweat management is still scarce for simultaneously achieving sustainable personal comfort. Here, we demonstrate a hierarchically arrayed fabric for personal EMI shielding and thermal comfort management. By integrating EMI shielding interfaces and spatially distributed channels, the fabric exhibits high-efficiency EMI shielding ability and enhanced sweat transportation. We demonstrate the tuning electromagnetic response with maximum EMI shielding efficiency value of ∼118 dB and continuous one-way liquid sweat flow with a temperature of ∼3.5 °C lower than that of conventional EMI shielding fabrics. In addition, the fabric shows substantially stabilized EMI shielding performance for long-term use by transporting and repelling internal liquid sweat. The high performance of our fabric makes it a promising design paradigm for personal electromagnetic interference shielding and thermal management.

Novel synthesis of CuFe2O4/g-C3N4 based on microwave ferromagnetic resonance effect for the thorough removal of TC in mariculture wastewater under natural sunlight

Superior separation of photogenerated carriers holds the key to intensive degradation of tetracycline (TC) in mariculture wastewater under natural sunlight. CuFe2O4/g-C3N4 (CFO/g) was synthesized by secondary microwave co-precipitation (SMCP) based on the ferromagnetic resonance absorption effect. Under the reaction conditions of pH = 6.5, CFO/g = 0.2 g/L, [H2O2] = 1 mM, 99.0 % TC removal was realized in 40 min. Enhanced performance for TC removal in high-salinity environments heavily relied on elevated ionic strength and rapid electron transfer of CFO/g in conjunction with high-salinity interactions. To ecologically remediate mariculture wastewater under natural sunlight, we immobilized powdered CFO/g to a ferrite magnet and devised a continuous flow reaction apparatus, incorporating the controlled injection of hydrogen peroxide (H2O2), to achieve the 100 % TC removal and simultaneously undertake the pretreatment of other contaminants (∼70 %). Ultimately, a safety assessment demonstrated that the degradation of mariculture wastewater by the CFO/g photo-Fenton system is a reliable and efficient technology, and the growth of clownfish remained unimpaired. SMCP successfully accelerated the conversion of high-valent metal ions to low-valent ones and eased the activation barriers of H2O2, enabling various active species to execute their respective roles productively. Innovative application of microwave resonance to enhance the magnetic properties of CFO/g and to support the equilibrium conversion of elemental valence states in high-salinity environments from real wastewater.

Promising membrane photobioreactor for continuous flow treatment of Low C/N wastewater: Treating process, community structure, and cooperation mechanism

Low carbon/nitrogen (C/N) wastewater treatment is an emerging issue for conventional treatment technologies. To achieve this goal, a novel membrane photobioreactor (MPBR), integrating microalgae consortium (MC) and activated sludge (AS) phases, was investigated. The separation of the MC and AS phases could improve the removal of pollutants in low C/N wastewater, which could achieve the rapid denitrogenation through NH4+-N assimilation in MC phase, and effectively reduce organic matter concentration in AS phase, resulting in better nutrient recovery, lower costs, and stable pH. The results in phase I showed that the pollutants, such as chemical oxygen demand (COD), ammonium (NH4+-N), and total phosphorus (TP), met the Environmental Quality Standards for Surface Water (GB3838–2002) by MPBR. The AS phase with low DO, which could enrich heterotrophic bacteria (e.g., Bacteroidetes vadinHA17, Spirochaeta and Ahniella) and nitrogen cycling bacteria (e.g., Mycobacterium, Bacillus and Ellin6067), could promote the removal of COD and NO3--N in the continuous effluent. Based on the co-occurrence pattern analysis, the main influencing factor of MC and AS phases was the reduction of COD, which also illustrated the synergistic removal of organic matter by the cooperative interaction of microalgae and heterotrophic bacteria. From a genetic perspective, the internal circulation mode also enhanced microbial nitrogen metabolism in the MPBRs, with higher abundances of nitrification- and denitrification-related functional genes in the MC phase, and higher abundances of nitrification, dissimilatory nitrate reduction, and denitrification genes in the AS phase. This study provided an experimental and theoretical basis for MPBR in low-C/N wastewater treatment.

Highly sensitive passive sampling of new pollutants in urban reclaimed water using hydrophilic-lipophilic balance sorbent-embedded cellulose acetate membrane

Urban reclaimed water is important water resource in China, while the residual new pollutants in the water largely challenge their safety for further use. China's action program for the management of new pollutants (also known as emerging contaminants) requires effective method for monitoring diverse new pollutants in water. This work proposed a highly sensitive passive sampling method for monitoring diverse new pollutants in urban reclaimed water. Hydrophilic–lipophilic balance sorbent-embedded cellulose acetate membranes (HECAMs) were dynamically deployed in self-developed continuous flow integrative sampling device (CFISD) for sampling four types of new pollutants with wide polarity ranges (1.11 < log Kow < 9.49) in a reclaimed water network for landscape irrigation in Beijing, China. The estimated equilibrium partition ratios of most chemicals between HECAM and water were over 104, which would provide low detection limits. In the 7-d high-efficiency deployment, thirty new pollutants were detected, which indicated incompletely removal of various new pollutants in wastewater treatment process. The dynamical accumulation data were successfully fitted by first-order kinetic model and different contaminants reached different accumulation phases in the HECAMs during 7 d. Acceptable and steady uptake rate constants and sampling rates were obtained with the use of CFISD in field sampling. The estimated time-weighted average concentrations for contaminants had wide concentration range and were from 0.03 ng L−1 (pendimethalin) to 3,394 ng L−1 (dibutyl phthalate) and this may lead to environmental risk for further use the reclaimed water. Dynamical deployment results also provided sensitive information of concentration fluctuations and twelve pollutants showed concentration fluctuations during the sampling period. In summary, HECAM showed high sensitivities and credible performance of monitoring diverse new pollutants in the urban reclaimed water.

Enhancing hydrogen generation from sodium borohydride hydrolysis and the role of a Co/CuFe2O4 nanocatalyst in a continuous flow system

In this study, a series of cobalt-based spinel ferrites catalysts, including nickel, cobalt, zinc, and copper ferrites, were synthesized using the sol–gel auto-combustion method followed by a chemical reduction process. These catalysts were employed for accelerating hydrogen generation via the sodium borohydride hydrolysis process. A continuous stirred tank reactor was used to perform catalytic reactor tests. All samples were subjected to analysis using XRD, FESEM, EDX, FTIR, and nitrogen adsorption–desorption techniques. The results revealed that the cobalt-based copper ferrite sample, Co/Cu-Ferrite, exhibited superior particle distribution, and porosity characteristics, as it achieved a high hydrogen generation rate of 2937 mL/min.gcat. In addition, the higher electrical donating property of Cu-Ferrite which leads to the increase in the electron density of the cobalt active sites can account for its superior performance towards hydrolysis of NaBH4. Using the Arrhenius equation and the zero-order reaction calculation, activation energy for the sodium borohydride hydrolysis reaction on the Co/Cu-Ferrite catalyst was determined to be 18.12 kJ/mol. This low activation energy compared to other cobalt-based spinel ferrite catalysts confirms the catalyst's superior performance as well. Additionally, the outcomes from the recycling experiments revealed a gradual decline in the catalyst's performance after each cycle during 4 repetitive cycles. The aforementioned properties render the Co/Cu-Ferrite catalyst an efficient catalyst for hydrogen generation through NaBH4 hydrolysis.

Selective Thermal Deprotection of N-Boc Protected Amines in Continuous Flow.

Thermal N-Boc deprotection of a range of amines is readily effected in continuous flow, in the absence of an acid catalyst. While the optimum results were obtained in methanol or trifluoroethanol, deprotection can be effected in a range of solvents of different polarities. Sequential selective deprotection of N-Boc groups has been demonstrated through temperature control, as exemplified by effective removal of an aryl N-Boc group in the presence of an alkyl N-Boc group. As a proof of principle, a telescoped sequence involving selective deprotection of an aryl N-Boc group from 9h followed by benzoylation and deprotection of the remaining alkyl N-Boc group to form amide 13 proved successful.

Highly stable WO3-Ag-AgCl films for continuous water treatment synthesized using a new low-cost ultrasonic spray-pyrolysis/photoreduction approach

This study reports the successful synthesis of WO3-Ag-AgCl films on glass substrates using a simple and cost-effective ultrasonic spray-pyrolysis/photoreduction method, intended for use in continuous flat plate photochemical reactors. A central composite design was used to optimize the amounts of WO3 and AgCl deposited on the substrate. The films synthesized under varying conditions exhibited heterojunctions of WO3 and AgCl, whose photocatalytic efficiency, assessed by the removal of the model contaminant acetaminophen (ACT) under continuous flow, was greatly influenced by the amount of AgCl deposited on the substrate, while that of WO3 had a minimal impact on ACT removal. The film with WO3:AgCl molar ratio of 1.84 showed exceptional stability over 20 h of continuous operation, with only a 4 % reduction in contaminant removal. Additional tests using a real pharmaceutical effluent spiked with ACT confirmed the high (>92 %) ACT removal of this film formulation and its stability; further tests indicated •OH and O2•− as the primary reactive species involved in the photodegradation reaction. Overall, these findings offer promising and cost-effective alternatives for synthesizing highly stable WO3-Ag-AgCl films that are efficient in treating real pharmaceutical effluents containing emerging contaminants using sunlight.

Stability of Iodine Species Trapped in Titanium-Based MOFs: MIL-125 and MIL-125_NH2.

Two titanium-based MOFs MIL-125 and MIL-125_NH2 are synthesized and characterized using high-temperature powder X-ray diffraction (PXRD), thermogravimetric analysis(TGA), N2 sorption, Fourier transformed infrared spectroscopy (FTIR), Raman spectroscopy, ultraviolet-visible spectroscopy (UV-Vis), and electron paramagnetic resonance (EPR). Stable up to 300°C, both compounds exhibited similar specific surface areas (SSA) values (1207 and 1099m2g-1 for MIL-125 and MIL-125_NH2, respectively). EPR signals of Ti3+ are observed in both, whith MIL-125_NH2 also showing ─NH2 ●+ signatures. Both MOFs efficiently adsorbed iodine in continuous gas flow over five days, with MIL-125 trapping 1.9g.g-1 and MIL-125_NH2 trapping 1.6g.g-1. MIL-125_NH2 exhibited faster adsorption kinetics due to its smaller band gap (2.5 against 3.6eV). In situ Raman spectroscopy conducted during iodine adsorption revealed signal evolution from "free" I2 to "perturbed" I2, and I3 -. TGA and in situ Raman desorption experiments showed that ─NH2 groups improved the stabilization of I3 - due to an electrostatic interaction with NH2 ●+BDC radicals. The Albery model indicated longer lifetimes for iodine desorption in I2@MIL-125_NH2, attributed to a rate-limiting step due to stronger interaction between the anionic iodine species and the ─NH2 ●+ radicals. This study underscores how MOFs with efficient charge separation and hole-stabilizer functional groups enhance iodine stability at higher temperatures.

Enhancing the implantation of mechanical circulatory support devices using computational simulations.

Introduction: Patients with end-stage heart failure (HF) may need mechanical circulatory support such as a left ventricular assist device (LVAD). However, there are a range of complications associated with LVAD including aortic regurgitation (AR) and thrombus formation. This study assesses whether the risk of developing aortic conditions can be minimised by optimising LVAD implantation technique. Methods: In this work, we evaluate the aortic flow patterns produced under different geometrical parameters for the anastomosis of the outflow graft (OG) to the aorta using computational fluid dynamics (CFD). A three-dimensional aortic model is created and the HeartMate III OG positioning is simulated by modifying (i) the distance from the anatomic ventriculo-arterial junction (AVJ) to the OG, (ii) the cardinal position around the aorta, and (iii) the angle between the aorta and the OG. The continuous LVAD flow and the remnant native cardiac cycle are used as inlet boundaries and the three-element Windkessel model is applied at the pressure outlets. Results: The analysis quantifies the impact of OG positioning on different haemodynamic parameters, including velocity, wall shear stress (WSS), pressure, vorticity and turbulent kinetic energy (TKE). We find that WSS on the aortic root (AoR) is around two times lower when the OG is attached to the coronal side of the aorta using an angle of 45° ± 10° at a distance of 55mm. Discussion: The results show that the OG placement may significantly influence the haemodynamic patterns, demonstrating the potential application of CFD for optimising OG positioning to minimise the risk of cardiovascular complications after LVAD implantation.

Production of fish feed by the aquaponic method

Aquaponics is one of the most efficient agricultural production systems; however, there is limited data on its level of effectiveness. The purpose of the research was to study the germination of wheat grain as aquaponic food for herbivorous fish in an aquaponic installation. The experimental production of aquaponic food for herbivorous fish grown in polyculture (carp, grass carp, black carp, silver carp) was studied by the method of wheat grain germination. In an aquaponic device, you can not only grow plants, but also germinate their seeds before planting in the ground. Water is saturated with oxygen due to continuous flow (3.5% more than in a pool without an aquaponic device). This is a positive factor for the growth of fish and energy savings while reducing the duration of the oxygen generators. In addition, the use of an aquaponic device provides favorable conditions for growing plants and fish with a significant reduction in the cost of installation of structures and a decrease in the cost of its operation. An increase in the germination of wheat grain during its germination in an aquaponic installation by 2.0% was established; increase in the length of sprouts during germination - by 27.5%; root length - by 32.2%; increase in the content of crude protein – by 2.2%; vitamin B2 - by 6.1%; carotene – by 4.6%. Hydroponic feed safety indicators were within the limits of sanitary and hygienic standards. The results of this study for the production of hydroponic feed for herbivorous fish directly in the fish farm show that in the production of valuable fortified vegetable environmentally safe feed, it is advisable to use the aquaponic method using water saturated with nutrients.

Detection of electrocatalytical and -chemical processes by means of in situ flow NMR spectroscopy

In situ studies of electrochemical processes using NMR offer valuable information on reaction mechanisms, kinetics, and species identification, making it a powerful tool in electrochemistry research. In this study, we present the design of an in situ redox-flow NMR cell that allows for a continuous flow of liquid (electrolyte) or gas, application of electrical voltage, and recording of NMR signals. The utility of this setup is demonstrated through two case studies: electrochemical copper deposition on a gold electrode and the electrochemical conversion of carbon dioxide into hydrocarbon products. Specifically, the presence of multicarbon products containing C–C bonds generated during the electrochemical reduction reaction is confirmed in the 2H NMR spectra in the latter example. These findings highlight the ability of the in situ redox-flow NMR cell to directly monitor reaction intermediates and products, thereby enabling the elucidation of reaction mechanisms for the efficient and selective production of valuable hydrocarbon products through the conversion of CO2 into value-added chemicals. In contrast to other reported in situ NMR cells, the presented cell is suitable for multiple uses, and allows detecting NMR signals not only from exhaust products but also from those formed on the catalyst surface.