Contaminated Soil Research Articles

Assessing Organochlorine Pesticide Behavior in Agricultural Watershed Soil, Water and Sediment: A Dynamic Modeling Approach

ABSTRACT The utilization of pesticides has experienced a substantial rise in order to enhance both the quantity and caliber of the produced goods. Agricultural runoff, a major source of nonpoint pollution, adversely impacts surface water, groundwater, soil and sediment quality in the watershed. Especially, organochlorine pesticides have adverse effects on the environment because of their toxicity, persistence and bioaccumulation. In this study, the presence of organochlorine pesticides (DDTs- dichlorodiphenyltrichloroethane and HCHs- hexachlorocyclohexane) in the environment of the dryland agricultural watershed, was determined. For this purpose, soil, sediment and water samples from the landscape of pond were collected. The concentrations of organochlorine pesticides in water, sediment, and soil ranged from 0.0005 to 0.0138 μg/L, 0.03 to 1.02 μg/kg, and 0.54 to 52 μg/kg, respectively. The persistence of these pesticides in soil and sediment poses long-term risks to both terrestrial and aquatic ecosystems. Sediment, as a significant reservoir for these contaminants, can act as a secondary source of pollution, releasing pesticides back into the water column under certain environmental conditions. Similarly, soil contamination not only affects plant health and productivity but also leads to further leaching and runoff into water bodies. The behavior of a toxic substance in water, soil and sediment environment, which is organochlorine pesticide, in a well-mixed lake watershed, was modeled using mass balances in the lake. Statistical analysis, including a paired t-test and calculation of the Nash-Sutcliffe index, confirms the consistency and reliability of the model’s predictions compared to observed data. Simulated concentrations closely matched observed values, and the distribution patterns and trends remained consistent across different months. Moreover, the Risk Quotient (RQ) for DDTs and HCHs is less than 0.1, indicating low ecological risk.

Transect approach for assessing major and trace elemental contamination in agricultural soils of the palamaner division, chittoor district, andhra pradesh, india.

Three soil transects located in the granitic regions of Palamaner mandal, Andhra Pradesh, India, were examined to assess the pollution levels of both primary and secondary metals (Si, Al, Fe, Ca, Mg, Na, K, Cu, Mn, P, and Zn) and to ascertain the degree of soil pollution in agricultural areas. The soils along these transects are slightly acid to neutral, with dark brown to red rubified argillic clay-rich B horizons alongside a moderate cation exchange capacity. The A horizon soils display low organic carbon levels with a moderate variability and contain over 70% SiO2, exhibiting low variability due to limited leaching in a semiarid climate. The findings suggest that iron (Fe) and manganese (Mn) oxides play a role in reducing contamination levels through oxidation and precipitation processes. Furthermore, the soils show low to moderate cation exchange capacity, which restricts the retention of absorbed heavy metals, thus lessening their negative impacts. A two-way ANOVA revealed significant differences in CEC, organic carbon, and total zinc content across different horizons and landscape positions. Si, Al, and Cu had small increases and negative geoaccumulation indices in all soil profiles, suggesting no pollution. However, the Nemerow and mean contamination degree over 6 point to slight to moderate pollution. The analysis identified three distinct clusters with significant variations in contamination factors for SiO2 and Cu. Five principal components were determined, explaining 76% of the total variance, primarily derived from geogenic sources and remaining within acceptable limits. This research on soil transects in granitic regions contributes to a better understanding of the distribution, movement, and concentration of elemental oxides based on slope position, which is essential for pollution assessment and soil quality enhancement.

Nanopriming with phytofabricated selenium nanoparticles alleviates arsenite-induced oxidative stress in Spinacia oleracea L.

Arsenic (As) contamination of agricultural soil has become a major concern due to its adverse effects on plant growth and human health. Selenium nanoparticles (SeNPs), a novel selenium (Se) source, are characterised by their exceptional biocompatibility, degradability, and bioactivities. In the present study, SeNPs were biogenically synthesised and further characterised using UV-visible spectroscopy, XRD, FTIR, and TEM analysis. Different concentrations of the synthesised SeNPs were used to treat Spinacia oleracea L. (spinach) seeds to determine their impact on growth profile, gas exchange, photosynthetic pigments, oxidative stress, and antioxidant enzyme status upon arsenite (AsIII) treatment. The findings revealed that SeNP supplementation at a concentration of 100µM (SeNPs100) led to a significant reduction in As accumulation by twofold in roots and 1.5-fold in leaves when compared to plants exposed to AsIII100 (µM) alone. Interestingly, the photosynthetic efficiency was also remarkably enhanced upon SeNPs100 treatment, associated with increased activities of the defence enzymes (ascorbate peroxidase, catalase, and glutathione peroxidase) in the AsIII + SeNP-exposed spinach plants as compared to AsIII treatment alone. Overall, the present study highlights the potential of biogenic SeNP supplementation in promoting plant growth and mitigating As toxicity in spinach under AsIII stress. This study could have significant implications for the use of SeNPs as a nanofertiliser in regions grappling with As-contaminated soils for sustainable agriculture and human health.

Engineered biochars for simultaneous immobilization of as and Cd in soil: Field evidence

Agricultural soil contamination by potentially toxic elements (PTEs) such as arsenic (As) and cadmium (Cd) poses a serious threat to food security. Immobilization serves as a widely used approach for the remediation of PTEs contaminated soils, nevertheless, the long-term effectiveness for the simultaneous immobilization of both cations and oxyanions remains a challenge. In order to effectively enhance the synergistic immobilization effect of soil As and Cd contaminated by multiple elements and improve the ecological environment of farmland. In this study, a typical polluted tailings area farmland was selected for situ immobilization experiments, and biochar was prepared from cow manure (CMB), rice straw (RSB), and pine wood (PWB) as raw materials. On this basis, the pristine biochar was modified with ferric chloride (F), potassium permanganate (K), magnesium chloride (M), and aluminum chloride (A), respectively. Furthermore, the immobilization effect of modified biochar on As-Cd and the stress effect on soil respiration were investigated. The results showed that CMB and RSB reduced the bioavailability of heavy metals, potassium permanganate has strong oxidizing properties, and the strong oxidability of potassium permanganate stimulated the generation of more oxygen-containing functional groups on the surface of biochar, thereby enhancing the adsorption and complexation effect of modified materials on As and Cd. Among them, the extracted Cd concentration of Diethylenetriamine pentaacetic acid (DTPA) in KCMB and KRSB in 2020 decreased by 8.23–43.12% and 9.67–35.29% compared to other treatments, respectively. Meanwhile, the KCMB and KRSB treatments also reduced the enrichment of As and Cd in plant tissues. In addition, the dissolved organic carbon (DOC) content in KCMB treatment was relatively high, and the carbon stability of the material was weakened. Simultaneously, the soil respiration emission of KCMB treatment was increased by 5.63% and 11.93% compared to KRSB and KPWB treatments, respectively. In addition, the structural equation also shows that DOC has a large positive effect on soil respiration. In summary, the KRSB treatment effectively achieve synergistic immobilization of As-Cd and provide important guiding significance for green and low-carbon remediation of polluted farmland.

Contaminants in the Soil and Typical Crops of the Pannonian Region of Slovenia

Soil contamination and the uptake of pollutants by food crops are widespread issues that vary greatly by region and are influenced by the mineral composition of the soil and local human activities. The Pannonian region, where agriculture has played a key role since Roman times, has been particularly impacted by the long-standing agricultural and industrial practices. While soil contamination with heavy metals is monitored by the Slovenian government, microplastic contamination and the uptake of pollutants into food crops have yet to become a regular component of monitoring efforts. In this study, we conducted a preliminary investigation into soil and crop contamination across the Pannonian region, focusing on identifying harmful contaminants and their potential uptake into food crops. Both soil and crop samples were analyzed for the presence of heavy metals with proven methods such as atomic absorption spectrometry (FASS), graphite furnace atomic absorption spectrometry (GF-AAS), atomic fluorescence spectrometry (AFS), and inductively coupled plasma–mass spectrometry (ICP-MS). Energy-dispersive X-ray spectroscopy (EDS) was found to be a potentially faster method of obtaining data on soil composition. Special attention was also given to the potential presence of microplastics in the region’s soils.

Risk assessment for soil contamination from artisanal lead-glazed pottery production in Maragogipinho, Bahia, Brazil

Pollution risk analyses are essential for the management of contaminated sites. In the village of Maragogipinho, Bahia, Brazil, artisans have been producing decorative and utilitarian pottery for almost 300 years. A lead-glaze is used on some of the products causing health concerns. An estimation of indexes for pollution and ecological and human health risks in the region around the pottery workshops was performed. The soil Pb content data from a recent study was used to evaluate the ecological and health risk indicators. These showed high values close to the pottery workshops. The risk for disease through Pb soil contamination is very high for children and high for adults close to the pottery workshops. It is estimated that about 1270 people are at risk in this region.

Soil contamination by trace elements and radioelements and related environmental risks in agricultural soils of the M'Dhilla Basin (southwestern Tunisia).

Agricultural soil contaminated by phosphogypsum pile stocked in plan air remains a major problem in M'Dhilla city southwestern of Tunisia. The present effort aimed to enhance the knowledge of trace elements and radioactivity abundance and to assess the corresponding environment. X-ray fluorescence spectroscopy was used to evaluate the trace elements, radioactive elements, and major element concentrations. Our finding revealed that the mean values of U and Th in all the soil profiles ranged from 0.283 to 2.875mg.kg-1 and from 0.797 to 1.491mg.kg-1 respectively. The statistical analyses indicated that uranium abundance has non-significant correlation with the most of trace metals; it shows a moderate correlated with Sr and inverse correlation with P2O5. Contamination factors indicate that the studied soil ranged from uncontaminated to significantly contaminated. Thus, the pollution load index values classify the sites from background values to high pollution sites. The findings of this study will help improve the environmental conditions of M'Dhilla city by addressing contamination issues through targeted interventions. The study's findings highlight the importance of a periodic environmental monitoring such as soil remediation in the study area. This research fills a critical gap in the current understanding of contamination management in this region.

Geochemical analysis of surface natural seepages and hydrocarbon fields of technogenic origin in the Amga River Basin (Siberian platform)

The presence of substantial accumulations of bitumen is critically significant as they serve as direct indicators of oilbearing regions. However, in the context of environmental studies, their existence complicates the assessment of technogenic soil contamination by oil and petroleum products. The objective of this research was to identify informative geochemical parameters that would facilitate the differentiation between natural surface seepages and technogenic hydrocarbon fields resulting from commercial oil spills. This study examined natural surface oil seepages in the Amga River Basin and technogenic oil contamination near the Amga Oil Depot. Employing classical bituminology, Fourier transform infrared spectroscopy, gas chromatography, and mass spectrometry, a comparative analysis of their compositional characteristics was conducted. Notably, significant differences in geochemical parameters, such as the concentrations of hydrocarbons, resins, asphaltenes, and oxygen-containing compounds, were observed when comparing oil pollution to natural surface seepages for the first time. Furthermore, it was demonstrated that genetic parameters for diagnosing soil contamination by oil, based on biomarker composition, could include the presence of 12- and 13-methylalkanes in the hydrocarbon profile of the pollutant. These compounds are recognized as distinctive biological markers of Cambrian and Early Paleozoic oils from the Nepsko-Botuobinsk oil and gas region. Conversely, these biomarkers were absent in the natural surface oil seepages of Amga. The findings of this research may prove valuable in environmental studies, particularly in monitoring efforts aimed at identifying technogenic oil contamination in soils that are not associated with natural oil seeps.

Novel nanocomposite and biochar insights to boost rice growth and alleviation of Cd toxicity

Cadmium (Cd) is an unessential and pervasive contaminant in agricultural soil, eventually affecting the food and instigating health issues. The implication of nanocomposites in agriculture attained significant attention to drive food security. Nanocomposites possess exceptional characteristics to stun the challenges of chemical fertilizers that can enhance plant yield and better nutrient bioavailability. Similarly, biochar has the ability to immobilize Cd in soil by reducing mobility and bioavailability. Rice husk biochar is produced at high temperature pyrolysis under anoxic conditions and a stable carbon-rich material is formed. To strive against this issue, rice plants were subjected to Cd (15, 20 mg kg− 1) stress and treated with alone/combined Ca + Mg (25 mg L− 1) nanocomposite and rice husk biochar. In our study, growth and yield traits showed the nurturing influence of Ca + Mg nanocomposite and biochar to improve rice defence mechanism by reducing Cd stress. Growth parameters root length 28%, shoot length 34%, root fresh weight 19%, shoot fresh weight 16%, root dry weight 9%, shoot dry weight 8%, number of tillers 32%, number of grains 20%, and spike length 17% were improved with combined application of Ca + Mg and biochar, with Cd (20 mg kg− 1), rivalled to alone biochar. Combined Ca + Mg and biochar application increased the SPAD 23%, total chlorophyll 26%, a 19%, b 18%, and carotenoids 15%, with Cd (20 mg kg− 1), rivalled to alone biochar. MDA 15%, H2O2 13%, and EL 10% were significantly regulated in shoots with combined Ca + Mg and biochar application with Cd (20 mg kg− 1) compared to alone biochar. POD 22%, SOD 17%, APX 18%, and CAT 9% were increased in shoots with combined Ca + Mg and biochar application with Cd (20 mg kg− 1) compared to alone biochar. Cd uptake in roots 13%, shoots 14%, and grains 21% were minimized under Cd (20 mg kg− 1) with combined Ca + Mg and B. pumilus application, compared to alone biochar. Subsequently, combined Ca + Mg and biochar application is a sustainable solution to boost crop production under Cd stress.

Real-time, specific, and label-free transistor-based sensing of organophosphates in liquid

Organophosphates (OP), commonly used in agriculture and as chemical warfare agents, pose significant environmental risks, necessitating real-time, low-cost OP detection methods. In particular, liquid-phase OP sensing with minimal sample volumes is crucial. While several methods allow rapid detection of low concentrations of OP vapors, they are effective only in the short term, while vapors are still being produced. Many OP compounds are semi-volatile, leading to the contamination of water, soil, and surfaces, posing a risk of secondary, long-term exposure. Detecting this contamination requires methods that can be directly applied to droplets of the affected medium. Currently, no method provides the desired combination of ultra-sensitivity, quantitative detection, rapid response, and low-cost for detecting OPs in liquid samples. This study aims to demonstrate quantitative, low-cost, real-time, specific, and label-free OP sensing in ultra-small samples using a transistor-based approach. The current work employs the 2-(4-Aminophenyl)-1,1,1,3,3,3-hexafluoro-2-propanol (aminophenyl-HFIP) functionalized meta-nano-channel field-effect chemical sensor (MNChem sensor) to monitor the organophosphate, diethyl cyanophosphonate (DCNP), in liquid samples. The silicon component of the MNChem is fabricated using a complementary metal-oxide semiconductor (CMOS) process, and the amine-based chemical functionalization of the sensing area is performed post-fabrication. The MNChem sensor provides electrostatic control over the source-drain current (IDS), allowing an optimized channel configuration that efficiently transduces localized OP recognition events into significant IDS variations. Sensing is performed using 0.5 μL buffer solution to simulate a miniature field-deployable sensor for on-site liquid analysis. We report the sensing of DCNP with a limit-of-detection of 100 fg/mL, a dynamic range of 9 orders of magnitude, and excellent linearity (≥0.97) and sensitivity. Control measurements confirm the specificity and reliability of the sensor's response, validating its applicability. This study introduces a novel method for OP detection in contaminated droplets using a low-cost disposable transistor technology.

Soil Degradation and Contamination Due to Armed Conflict in Ukraine

Soil Degradation and Contamination Due to Armed Conflict in Ukraine

Effect of long-term application of pig slurry and NPK fertilizers on trace metal content in the soil.

One of the goals of sustainable agricultural production is to avoid soil contamination by elements defined as trace metals (TMs). The aim of this study was to assess the long-term impact of the use of pig slurry (PS) and NPK mineral fertilizers on the soil content of cadmium (Cd), copper (Cu), lead (Pb) and zinc (Zn). In a 9-year crop rotation, PS was used three times only before root crops. The same four levels of NPK doses (N0P0K0, N1P1K1, N3P2K2, N4P2K2) were applied to both plots with and without PS. Soil samples were collected in early spring from topsoil (0-0.3m) and subsoil (0.3-0.6m). Three forms of TMs were determined in the soil: pseudo-total (Aqua regia); bioavailable (Mehlich 3 method) and readily bioavailable (mobile) forms (1M NH4NO3). The tested factors did not have a significant impact on the Cd, Cu and Pb content, regardless of the form analyzed and the soil depth. PS application significantly increased the content of bioavailable forms of Zn regardless of the year, and the content of pseudo-total Zn only in the sugar beet year, i.e. after manure application. Increasing NPK doses increased the content of mobile Zn in the topsoil, especially in PS plots. A tendency to accumulate mobile forms of Cd and Pb was also observed on NPK-fertilized plots. Thus, long-term application of high NPK doses may increase the risk of contamination of the food chain with these metals. The content of mobile Cd and Zn was positively related to the content of total nitrogen in the soil and negatively related to pH.

Treatment of biowaste commingled with biodegradable bioplastic films using Black Soldier Fly larvae: Generation and fate of micro-plastics

The use of Black Soldier Fly (BSF) larvae is emerging as a promising alternative for biowaste (i.e. food waste) treatment, generating larval biomass and process residues, suitable for use as animal feed and fertilizer, respectively. In line with an increasing use of starch-based bioplastics in food packaging, the presence of these biopolymers and associated biodegradable microplastics (BMPs) in food waste is expected to rise. Knowledge of the generation of BMPs and their fate in the BSF treatment process is scarce, or indeed, completely lacking in the case of small-sized BMPs (<50 μm). The present study aims to investigate the generation and potential accumulation of BMPs in BSF larvae process. Food waste mixed with starch-based bioplastic films was fed to larvae and BMPs of two particle sizes (inferior to and exceeding 10 μm in diameter) were monitored over time in rearing substrate and larval biomass. BMPs concentrations in substrate were compared with larvae-free control tests. The presence of larvae favoured the generation of BMPs. Concentrations of smaller-sized BMPs (<10 μm) increased by approximately 172% in the final substrate, and accumulated in the larval biomass with a peak exceeding the initial larval concentration by over 1000% just before prepupation, which is the typical stage they are collected when used as animal feed. These results indicate a potential risk of soil contamination by BMPs when final substrate is used as fertilizer and a risk of biomagnification phenomena when larvae are used as animal feed.

Comparative effects of micron-sized silicon sources and Si nanoparticles on growth, defense system and cadmium accumulation in wheat (Triticum aestivum L.) cultivated in Cd contaminated soil

Elevated levels of cadmium (Cd) in soils posesignificant challenges to global agricultural crop production. The potential of silicon (Si) nanoparticles (NPs) and biogenic Si sources of different sizes to mitigate Cd stress in wheat remains largely unexplored. A pot experiment was conducted to evaluate the effectiveness of various sizes of biogenic Si sources: rice husk biochar (RHB), sugarcane bagasse (SB), and rice straw (RS); categorized by particle size (<150 μm, 150–250 μm, and 250–1680 μm, denoted as S1, S2, and S3, respectively), and Si NPs on wheat growth and Cd accumulation. The application of RHB (<150 μm) significantly increased plant height (105 %), spike length (94 %), shoot dry weight (93 %), root dry weight (83 %), and grain weight (89 %) compared to the control. The RHBS1 treatment delivered the greatest reduction in the bioavailable fraction of soil Cd (-74 %), as well as Cd levels in roots (-85 %), shoots (-93 %), and grains (-97 %) compared to the polluted control. Additionally, RHB (<150 μm) showed the highest increase in antioxidant enzyme activities compared to the Cd-spiked treatment. Interestingly, the various biogenic Si sources have the potential to mitigate Cd stress in wheat plants. Further research is required to understand the underlying mechanisms and to investigate the effectiveness of different biogenic Si sources and particle sizes in alleviating Cd stress in crops.

Ultra-sensitive zinc cobaltate assembled on N-rich carbon nitride electrochemical sensor for the detection of paraquat in food samples

BackgroundParaquat (PQ) from agricultural waste cause contamination in water bodies, groundwater, soil, and foods has received increasing attention regarding health safety. On-site-based detection is much needed along with rapid results, selectivity and sensitivity, which can be achieved through an electrochemical-based sensor. MethodsThis work provides, an electrochemical sensor based on zinc cobaltite (ZnCo2O4) nanostructure strongly attracted through electrostatic interaction with the carbon nitride (C3N5; CN) nanosheets modified on a glassy carbon electrode (GCE) for the determination of paraquat (PQ). The strong immobilization of ZnCo2O4 over CN2 on GCE synergistically shows excellent sensing of PQ due to high interfacial charge transfer effect. Significant findingsIn addition, the electrochemical studies were performed using CV and DPV analysis which exhibits a good limit of detection (7.6 nM) and sensitivity (0.201 µA cm-2) towards PQ detection. Furthermore, the modified electrode was applied practically in real food samples for PQ detection with excellent recoveries.

Application of Spectral Indices in the Evaluation of Soil-Oil Interaction and Enhanced Detection and Quantification of Oil Contaminants in Bare Soils

ABSTRACT Current methods to monitor oil contamination in bare soils rely upon geophysical techniques or direct sampling and testing, and their use amongst the global community is limited by their complexity and cost. Recent studies demonstrate that Visible-Near Infrared Spectroscopy (VNIRS) may be a reliable technique, but has found limited use due to effects of soil composition and moisture content. This study describes two spectral indices, the ‘Total Petroleum Hydrocarbon Index’ (TPHix) and ‘Oil Index’ (Oix), and demonstrate their application in enhanced detection of oil contaminants and the evaluation of soil-oil-water interaction in bare soils. To validate their applicability, soil-oil experiments were performed on 26 samples comprising of 12 artificial and 14 natural soils in dry states, and 10 sub-samples in wet condition. Analyses of TPHix demonstrate that this index provides a better estimate of low oil content in different soil classes, while Oix versus % Oil regression plots with a discrete inflection point termed the ‘Critical Point’ (CP) give an indication of soil-oil-water interaction as CP varies with soil composition and moisture content. This research demonstrates that VNIRS indices can improve oil contaminants detection in soils and provide insight into soil-oil-water interaction where there are few established techniques available to researchers.

Effect of wildfires on mobility of metribuzine herbicide in agricultural soil

Metribuzine has been used extensively for controlling wide range of broadleaf weeds and grasses, which can lead to severe contamination of soil and groundwater. Wildfires are an important process in environment, which can be severe for many areas and could have a significant impact on the properties of the soil. The objective of this study was to investigate the effect of wildfires for the fate and transport of atrazine for agricultural soil. Miscible displacement experiments were used for the objectives. Results showed that the average distribution coefficient (Kd) obtained from metribuzine was 0.28 and 0.13 L/Kg for soils prior to and after wildfire, respectively. Results indicate that organic matter content of soil has most likely played major role on sorption of metribuzine and exhibited rate-limited sorption-desorption. In addition, sorption of metribuzine onto soil after wildfire was significantly lower which could lead to more contamination risk of groundwater resources. The results from the present study would also help in designing of effective herbicide management strategies for contaminated sites.

A Review of Analytical Techniques to Characterise Nanomaterial Associations with Minerals, Organic Matter and Organisms

Nanomaterials (NMs) have unique properties and control processes relevant to the fate of contaminants in soils, air, and aquatic systems and within the carbon cycle. Many NMs often occur in association with larger mineral grains, organic matter, or living organisms such as microbes, plants and fungi. The preservation of the spatial, textural, chemical, and mineralogical relations between NMs and minerals, organic matter, and organism (NM‐associations) is of fundamental importance as it provides information about the origin and formation mechanisms of NMs. Here we review analytical approaches and techniques to study NM‐associations at the bulk‐, micro‐, nano‐ and atomic‐scale. We will focus on (a) X‐ray diffraction and mass‐spectroscopy techniques; (2) automatisms within software packages that permit the search of features without operators; (3) preparation and analytical techniques such as the focused‐ion beam technology, transmission electron microscopy and atom probe tomography; (4) nano‐spectroscopic techniques such as tip‐enhanced Raman spectroscopy, synchrotron infrared nanospectroscopy, and nano‐X‐ray fluorescence spectroscopy; (5) ptychographic X‐ray computer tomography. This review paper concludes with selected new perspectives such as (a) the characterisation of NM‐precursors, (b) the role of NM‐associations in the stabilisation of soil organic matter and (c) the interaction of NM‐associations in wildfire smoke with contaminants from other sources.

Spring water discharge and metal enrichment in urban soils

Abstract Urban centers have inherited a unique mix of persistent contamination that impacts interactions among urban soil and groundwater systems. In particular, the potential for urban groundwater to transport contaminants from surface sources through the subsurface environment and ultimately to soils is not well understood. Studies have focused on specific ‘natural’ mechanisms driving distribution of metals in urban soils. However, very few studies have examined the accumulation of contamination in soils at groundwater discharge locations (springs) and the potential for groundwater to redistribute urban legacy contaminants far from the source. Soil transects straddling four groundwater springs in Pittsburgh, Pennsylvania were sampled to evaluate patterns resulting from contaminated groundwater discharge on urban soils. Metal concentrations were measured in pore water and compared with concentrations observed in total digestions and exchangeable extractions (acetic acid) of the soil. Across the springs Co, Cr, Ni, and V (metals often used in steel alloys) were elevated downslope, suggesting contaminated groundwater discharge enriches trace metals in these locations. These processes create unexpected biogeochemical patterns on the landscape and have the potential to create hotspots of soil metal contamination at predictable points across the urban landscape.

Effects of temperature, relative humidity and soil organic carbon content on soil-air partitioning coefficients of volatile PFAS.

Soil-air partitioning coefficient (KSA) values are often used to assess the environmental fate of organic contaminants in soil. Till now, sufficient KSA values have not yet been measured for many compounds of interest, including some emerging pollutants such as volatile PFAS. Moreover, the effects of environmental factors such as temperature, relative humidity and soil organic carbon content on KSA of volatile PFAS are also unclear. In this study, the KSA values of target volatile PFAS were measured under various temperature (20-40 °C), relative humidity (30-100 %) and soil organic carbon content (2.1 %-8.0 %) using a modified solid-phase fugacity meter. The results showed that higher temperatures, higher relative humidity and lower organic carbon content in soil may accelerate the diffusion of target volatile PFAS. Furthermore, the KSA measurements were used to derive a multiple linear regression model to depict the relationship between logKSA and temperature, relative humidity, soil organic carbon content and PFAS-specific logKOA. When compared with the predictions obtained from semi-empirical model, we argued that the multiple linear regression model is more robust and easier to implement for target volatile PFAS or other emerging volatile PFAS than the semi-empirical approach to help depict the diffusion process at target volatile PFAS contaminated sites.