Constant Humidity Research Articles

Research on Photoelectric Responses of SnO₂ Film to Humidity Under UV Light Irradiation.

In this work, to research the photoelectric responses to humidity using a semiconductor film, an ultraviolet (UV) light induced device has been investigated on SnO₂ film at room temperature. Screen printing method was used to prepare SnO₂ film on the Al₂O₃ substrate. The crystalline structure and morphology of SnO₂ was characterized with XRD and FE-SEM. The UV light induced photoelectric responses of SnO₂ to a constant humidity (20% RH) were evaluated firstly under four different bias voltages. At 2 V bias voltage, the photocurrent amplitude reaches 4.58 μA, which is higher than that of 0.2 V bias (0.27 μA). Then the photoelectric responses to different relative humidity conditions (20% RH, 40% RH and 60% RH) were tested. The results display that the photocurrent decreased while the relative humidity increased. To illustrate the anomaly current of SnO₂ film at 60% RH, the darkcurrent to different relative humidity conditions (20% RH, 40% RH and 60% RH) were also tested. To make clear these results, corresponding probable illustration was proposed.

Effect of intrinsic PCB parameters on the performance of fluoropolymer coating under condensing humidity conditions

In this work, Fluoropolymer-based ultrathin coating is evaluated as a protective barrier for Printed Circuit Board (PCB) against corrosion failures. Constant humidity with temperature cycling was applied as external climatic conditions for performance assessment through electrochemical AC impedance and DC potentiostatic measurements. Morphology of the coating before and after test was inspected using Optical, Scanning Electron Microscopy (SEM), and Energy Dispersive Spectroscopy (EDS). Fluoropolymer coating was applied on a PCB interdigitated pattern used as test substrate. The effect of test board cleanliness, coating thickness, and orientation of the PCB placed inside a climatic chamber were investigated with subsequent corrosion morphology observations after climatic exposure. The study showed that the PCB cleanliness as a critical factor controlling performance with less reliance on the orientation of the PCB and the thickness of the coating.

Experimental validation of the predicted peak cutting force for seafloor polymetallic sulfide

Abstract With the gradual reduction of mineral resources, marine mining has increasingly been developed as a method of exploiting resources. However, the cutting efficiency of submarine mineral deposits requires additional improvement. Investigating the preferable cutting efficiency in marine mining, it is important to establish a theoretical model of predicting the peak cutting force for polymetallic sulfide. The polymetallic sulfide was taken from the floor of the Indian Ocean and maintained at constant temperature and humidity conditions during transportation. In the paper, some experiments were conducted to study the physicomechanical properties of polymetallic sulfide. And the cutting experiments were conducted to investigate the cutting force at room temperature and atmosphere pressure, preliminarily. Then, based on maximum tensile stress theory, the theoretical equation of predicting the peak cutting force was derived, and an improved high-precision theoretical model was established. The reliability and accuracy of this model was verified using the experimental data. Based on the improved theoretical model, the brittleness index and the cutting depth, which influenced the peak cutting force, were investigated. Results show that the established model improved the accuracy of predictions. The peak cutting force decreased with the increase of the brittleness index, but it increased with the increase of the depth, which followed the power-law pattern. The power-law coefficient was generally at 1-2. The experiments verified that this improved theoretical model and the related conclusions can predict the peak cutting force. It is significant for the design and study of conical picks and cutting mechanisms in marine mining.

The Impact of Growth-Promoting Streptomycetes Isolated from Rhizosphere and Bulk Soil on Oilseed Rape (Brassica napus L.) Growth Parameters

Inoculation of Streptomyces to improve oilseed rape (Brassica napus L.) yields and minimise the use of chemical fertilisers is a promising sustainable strategy. In this study, we isolated 72 actinobacterial strains from rhizosphere of oilseed rape and maize and from bulk soil for screening and characterising their antimicrobial activity. Nine promising strains, identified as Streptomyces sp. by morphology, physiological characteristics, and 16S rRNA gene sequencing, were selected for their plant growth-promoting traits and in planta experiments. The actinobacterial strains were positive for IAA production, siderophore production, and HCN production. In planta experiments were conducted by soaking the oilseed rape seeds in the actinobacterial suspension, followed by plant growth under controlled conditions in a cultivate chamber (22–28 °C, 8 h dark/16 h light, constant humidity 80%). We recorded root and shoot length (cm) and seedling fresh weight (g). For most of the abovementioned parameters, a significant enhancement was observed with strain KmiRC20A118 treatment. The length of the root increased by 53.14%, the shoot length increased by 65.6%, and the weight of the fresh plant by 60% compared to the control. The integrated application of PGPS (Plant Growth Promoting Streptomyces) from the rhizosphere of oilseed rape is a promising strategy to improve the growth of oilseed rape.

Ergoophthalmological risks associated with dry eye in the operating room

Dry eye disease is one of the most common pathologies of the ocular surface. In parallel with increased screen exposure, environmental changes and modern life in recent years, the prevalence and severity of dry eye have been increasing. Ergoophthalmology is the study of visual ergonomic conditions. It is concerned with injuries to the eyes caused by occupational factors and uses a multidisciplinary approach to understand the causes of occupational vision-related and ocular diseases and to prevent and manage these conditions. Vision-related risks in the operating room are critical for patients and health care providers. There are many predisposing factors in the operating room environment – air conditioning, constant humidity, constant room temperature, intense lighting, surgical smoke, anaesthetic gases and the use of irritant chemicals and biological aerosols. In addition, surgery itself is a critical task requiring long-term mental effort and concentration which can also predispose operating room staff to dry eye disease. In this review, we discuss occupational and environmental ergoophthalmological risk factors for dry eye disease in the operating room.

Better light spectral quality and thermal amplitude inside the greenhouse stimulate growth and improve acclimatization of in vitro–grown Cattleya warneri T. Moore

Growth and photosynthetic capacity of Cattleya warneri T. Moore seedlings cultivated in vitro were evaluated in two environments: (1) growth room (GR) with constant light, humidity, and temperature; and (2) greenhouse (GH) with variable humidity, temperature, and light intensity and quality. In both environments, two different tissue culture vessel lids were used: transparent plastic lids (TCVplastic) and non-transparent metal lids (TCVmetal). After 11 months of in vitro cultivation, five seedlings from each tissue culture vessel were evaluated for growth and photosynthetic capacity, while the other five seedlings of each tissue culture vessel were transferred to a greenhouse for acclimatization. Increased biomass production in vitro was observed in GH and GR (GH>GR). However, the photosynthetic capacity was not altered by the GH environment, since the net photosynthetic rate at 300 μmol m−2 s−1 (NPR300) was low in the final of period in all treatments. Therefore, the increase in biomass production in C. warneri was mostly dependent on the exogenous carbon source through the addition of sucrose to the culture medium. The use of TCVplastic in vitro improved seedlings’ growth in both GR and GH, showing an advantage in relation to TCVmetal. GH environment with quality light spectrum and thermal amplitude, and use of TCVplastic, increased biomass production in vitro and improved the acclimatization process of C. warneri seedlings, which also reduced electricity costs since the use of artificial light and air conditioning is not required.

Design, construction, and testing of an accurate low-cost humidistat for laboratory-scale applications

Stable and precise control of humidity is imperative for a wide variety of experiments. However, commercially available humidistats (devices that maintain a constant humidity) are often prohibitively expensive. Here, we present a simple yet effective humidistat for laboratory-scale applications that can be easily and affordably (<€250) constructed based on an Arduino Uno as microcontroller, a set of proportional miniature solenoid valves, a gas washing bottle, and a humidity sensor. The microcontroller implements a PID controller that regulates the ratio of a dry and humid airflow. The design and implementation of the device, including a custom driver circuit for the solenoids, are described in detail, and the firmware is freely available online. Finally, we demonstrate its proper operation and performance through step response and long-term stability tests, which shows settling times of approx. 30 s and an attainable relative humidity range of 10–95%

Effects of torrefaction conditions on the hygroscopicity of biochars

Agroforestry biomass involving cedar wood (CW), polar wood (PW), corn stalk (CS) and wheat straw (WS) was torrefied in a fixed-bed reactor under the torrefaction temperature (T) of 200–300 °C and the holding time (τ) of 10–60 min to prepared straw biochars (WSC, CSC) and woody biochars (PWC and CWC). The effects of biomass species, torrefaction temperature and holding time on the hygroscopicity of biochars were investigated under constant temperature and humidity. Combined with the results of N2 adsorption/desorption and FTIR of raw biomass and its biochars, the mechanism of torrefaction conditions on the hygroscopicity of biochar was discussed. The obtained results indicated that water absorption process of biochar can be divided into two stages of initial rapid water absorption and the later slow water absorption. The equilibrium moisture content (EMC) decreases, the hygroscopicity reduction extent (HRE) increases gradually, and hydrophobicity of biochar is enhanced with increasing torrefaction temperature. However, too high torrefaction temperatures (T ≥ 275 °C) has little or even adverse effect on the hydrophobicity of biochars. The longer holding time has a certain influence on the hydrophobicity of biochar, but the overall effect is not significant. The hydrophobicity of woody biochars (PWC and CWC) is better than that of straw biochars (WSC and CSC) at the same torrefaction conditions. The severe torrefaction of T ≥ 275 °C and τ ≥ 40 min are able to improve the hydrophobicity of woody biochars, however it has negative effect on straw biochars. The hydrophobicity of four biochars is ordered as PW > CW > WS ≈ CS at the same torrefaction conditions. The water adsorption mechanism of biochars is influenced by the coupling effects of physical structure evolution, release of hydrophilic oxygen-containing functional groups and pyrolytic tar condensation, and the severer the torrefaction, the more significant the influence is.

Vegetation Cover and Tumuli’s Shape as Affecting Factors of Microclimate and Biodeterioration Risk for the Conservation of Etruscan Tombs (Tarquinia, Italy)

The conservation of underground tombs is affected by several physical-chemical and biological factors, which could be reduced by insulating systems able to maintain the microclimatic stability also decreasing the biodeterioration risk. In Mediterranean areas, wild ephemeral plants, which reduce their cover during the hot season, seem unsuitable for reducing summer overheating. In this study, we wish to assess the influence of vegetation cover and of overlaying soil, after the establishment of an evergreen turf of a cultivar of Cynodon dactylon, on two tombs in the Etruscan Necropolis of Monterozzi, covered by linear-shaped tumuli. Therefore, we evaluated for 10 months the thermo-hygrometric values of these tombs, together with two tombs as controls. We also evaluated the different tumuli’s morphologies and the related received solar radiation. Results confirmed that late summer and early autumn as critical microclimatic periods for the risk factors of hypogeal paintings when peaks of superficial temperature occur. A positive influence of vegetation cover on maintaining constant humidity and internal temperatures was detected, but the mounds orientation, as well as soil depth, seems to have a relevant role. Considering the naturalistic features of the area and the related cultural ecosystem services, a careful selection of wild plants is suggested.

Interference of germination on the nutritional composition and antioxidant capacity of black sesame (Sesamum indicum L.)

PurposeThe purpose of this study was to evaluate the effect of black sesame germination on its nutritional composition and antioxidant activity.Design/methodology/approachGermination occurred at constant temperature and humidity (35 °C and 95 ± 5%) for 72 h. The levels of moisture, protein, lipids, ash, total dietary fibre and fractions, carbohydrates, calories, phenolic compounds and antioxidant capacity were determined.FindingsWith germination, there was a significant increase in moisture and protein content, as well as a reduction in the other parameters assessed in terms of nutritional composition. When analysing bioactive compounds, no significant change was found in the content of phenolic compounds; however, there was a reduction in antioxidant capacity according to the three methods tested, which may be related to the characteristics of the grain itself, the conditions used for germination, or even the process of extracting phenolic compounds for analysis. Other conditions for the germination of black sesame using different times and temperatures should be evaluated in future studies.Originality/valueThis is an original research article, which has an industrial and health impact by transmitting highly relevant responses on nutrition and food. The novelty of this research is the fact of studying the germination of black sesame on the nutritional composition (moisture, protein, lipids, ash, total dietary fibre and fractions, carbohydrates and calories), levels of phenolic compounds and antioxidant capacity. These results can help improve the procedures adopted by the food industries and also in nutritional conduct, as the germination process leads to a change in the nutritional composition, especially with regard to protein synthesis, which is relevant, once it is an interesting protein option. However, it also brings us responses to reductions in important nutritional compounds.

Exploration on key factors for overall migration into olive oil of food-contact silicone

To ensure the accuracy of the overall migration into olive oil of high risk food-contact silicone products, the key factors of the test method on the base of EN1186-1 &2 were analyzed and discussed. Two sample conditioning methods for the silicone products were compared, and the extraction times for olive oil in the samples were investigated, as well as the change trend of the actual temperature of olive oil at the set temperature. Using calcium chloride dryer conditioning method can achieve the same effect of constant temperature and humidity method, and can significantly reduce the conditioning time. For silicone products that are easily absorbed oil, the olive oil in the sample should be extracted at least twice. The temperature of the oven should be increased appropriately to meet the requirements of the temperature of olive oil. The water conditioning of samples, the extraction times of olive oil and the preheating temperature of olive oil are the key factors for olive oil overall migration of food-contact silicone, which can provide a reference for testing workers of food-contact materials.

Moisture sorption and thermodynamic properties of Camellia oleifera seeds as influenced by oil content

Moisture sorption isotherms and thermodynamic properties of Camellia oleifera seeds as influenced by oil content were investigated. Moisture desorption and adsorption isotherms of Camellia oleifera seeds, kernels and shells from three varieties were determined using constant temperature and humidity chamber method at different temperatures (10°C, 25°C, and 40°C) with water activity ranging from 0.20 to 0.90. Six selected mathematic models were employed to fit the experimental data. The Peleg model gave the best results for both seeds and kernels and Langmuir model was the best for shells. The difference of equilibrium moisture contents at the same water activities during desorption and adsorption indicated the occurrence of hysteresis of adsorption processes and the equilibrium moisture contents tended to decrease with the increasing oil content and temperature. The binding energy and average capacity per unit mass decreased with increasing temperature and oil content. The relationships between water activity and the logarithm of sorption activity showed the capillary porous body characteristics of the seeds. Keywords: Camellia oleifera seeds, moisture desorption and adsorption isotherms, equilibrium moisture content, oil content, thermodynamic property DOI: 10.25165/j.ijabe.20211401.5457 Citation: Zhu G F, Jin Q, Liu Y H, Lin Y W, Wang J, Li X Y. Moisture sorption and thermodynamic properties of Camellia oleifera seeds as influenced by oil content. Int J Agric & Biol Eng, 2021; 14(1): 251–258.

ANALYSIS OF HYGRO-MECHANICAL BEHAVIOR OF WOOD IN BENDING

The empirical test developed as validation for a new beam element model that can account for both mechanical and environmental load action in finite element analysis is presented. The testing protocol allows for the identification and analysis of contributing deflection components in bending under varying MC conditions, including mechano-sorption. The components of deflection in the shear-free span of a four-point bending test and their responses to varying moisture are evaluated with an analytical procedure. The experiment was conducted on clear-straight-grained sapwood and heartwood specimens of Norway spruce (Picea Abies)(30 x 15 x 640 mm3). The program consisted of three phases: (1.) long term (LT) experiments under constant temperature of 60oC and relative humidity (RH) cycles between 40% and 80%, (2.) a short term static experiment to determine the variation in the sample set and the load-level of the LT experiment on end-matched specimens, and (3) creep tests at 60o and constant humidity at either 40% or 80% to determine the effect of moisture on the viscoelastic creep. Mass changes and hygro-expansion measured on matched specimens were used in the analytical method. Constitutive models used for describing the material-level response to loads and moisture changes were applied to the shear-free segment of the specimens disregarding actual moisture gradients and fiber orientation inside the test specimens. A successful identification of each deflection component and isolation of mechano-sorption component was accomplished. In the 90 da of testing, the dominant component of the total deflection was the elastic component, followed by the mechano-sorptive component. Creep was found to be nonnegligible and important in the correct description of mechano-sorption. The effect of moisture on the viscoelastic behavior showed most important during loading and first stages of decreasing deflection rate phase.

A preliminary study of the weathering mechanism of fossilized Cretaceous Hamipterus bones

The discovery of Hamipterus tianshanensis had important scientific significance because three-dimensional preserved fossils can provide unique information about the reproduction, development, and evolution of pterosaurs. However, the pterosaur fossils exhibited violent weathering, including noticeable cracking and spalling, since the preservation environment changed dramatically after excavation, which severely influenced the preservation of these fossils and the scientific research conducted on them. To determine the weathering mechanism of these fossil bones, the samples were analyzed using X-ray fluorescence (XRF), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy and energy dispersive spectrometry (SEM-EDS). The results indicate that calcite is the main mineral in the hollow bones, but it is mixed with a small amount of other minerals, such as quartz, feldspar, and other debris particles. Moreover, the main component of the pterosaur bones is hydroxyapatite, and carbonate has substituted for some of the phosphate (B-type carbonated apatite) in the fossil bones. A small amount of calcite and manganese oxides has precipitated in the vascular canals. The phosphate crystallinity index (PCI) is 4.17. These results indicate that the fossils have undergone severe diagenesis. Apart from these alterations, the fossil bones have high contents of anions and cations such as Cl−, NO3−, SO42−, Na+, and Ca2+, and the total content of soluble salts is 35584.41 μg g−1. Based on these results, it is inferred that the weathering mechanism of the fossil bones is as follows. First, the fragile hollow bones cracked easily because of the enormous thermal stress caused by the dramatic temperature changes in the Gobi Desert and the differences in the thermal expansion coefficients (TEC) of the surrounding rocks, the fossil bones, and the different fillers. Second, a large amount of stress is generated by salt crystallization when the temperature and humidity change, and the pterosaur fossils will be damaged when the crystallization pressure exceeds the tensile strength of the fossils. These results suggest that the preservation of pterosaur fossils requires suitable desalination and consolidation conditions. Moreover, they should be preserved in a constant temperature and humidity environment.

Physical, Chemical and Biological Characteristics of Dew and Rainwater during the Dry Season of Tropical Islands

In order to establish data to be used for comparison with future evolution related to climate change, physical, chemical and biological characteristics of dew and rainwater as collected during the 2005 dry season (plus a few data during the 2004 dry season) are reported. They have been collected in two characteristic tropical islands of French Polynesia, Tikehau (TKH), a low-lying coral atoll in the Tuamotu Archipelago, and the mountainous Tahiti island at the University of French Polynesia (TAH). Trade winds dominate the trajectory of air masses, ensuring constant temperature and humidity to the lower layers of the atmosphere where dew forms. In addition to the comparison of dew yields with a physical model using simple meteorological data (air and dew point temperatures, windspeed, cloud cover), the following parameters were studied: pH, electrical conductivity (EC), total dissolved solids (TDS), total hardness, suspended matter, ion concentration with major cations (Ca2+, K+, Na+, Mg2+, NH4+) and major anions (Cl−, SO42−, NO3−), reviviscible aerobe microorganisms and compared to two Polynesian spring waters (“Eau Royale” and “Vaimato”). Dew, with a chemical composition mainly consisting of Na+, Ca2+, Mg2+, Cl− and SO42−, exhibits much higher ion concentration than rain and compares well with the composition of local spring waters. The values of pH, EC and TDS are larger in dew than in rainwater. At TAH, the volume weighted mean (VWM) pH values of dew were 6.05 in 2004 and 5.23 in 2005, larger than the pH of rain (4.69). The VWM dew EC (at TAH, 203 μS·cm−1 in 2004 and 237 μS·cm−1 in 2005; 321 μS·cm−1 at TKH in 2005) and dew TDS (152 mg·L−1 at TAH and 225 mg·L−1 at TKH) were higher than the corresponding quantities in rain. Mean total hardness (TH) values of dew water are much higher than in rainwater (2.8 for dew versus 0.5 for rain at TAH and 5.7 for dew versus 0.5 for rain at TKH). Ions Na+, Mg2+ and Cl− are clearly of sea origin while the presence of Ca2+ is due to coral particles. From their chemical characteristics, dew and rainwater could be used as an alternative source of water in dry season but, due to the presence of reviviscible aerobe microorganisms at 22 °C and 36 °C (&gt;300 CFU·mL−1), water must be disinfected to be potable.

Absolute Purity Determination of a Hygroscopic Substance, Indocyanine Green, Using Quantitative NMR (qNMR).

Quantitative NMR (qNMR) is applied to determine the absolute quantitative value of analytical standards for HPLC-based quantification. We have previously reported the optimal and reproducible sample preparation method for qNMR of hygroscopic reagents, such as saikosaponin a, which is used as an analytical standard in the assay of crude drug section of Japanese Pharmacopoeia (JP). In this study, we examined the absolute purity determination of a hygroscopic substance, indocyanine green (ICG), listed in the Japanese Pharmaceutical Codex 2002, using qNMR for standardization by focusing on the adaptation of ICG to JP. The purity of ICG, as an official non-Pharmacopoeial reference standard (non-PRS), had high variation (86.12 ± 2.70%) when preparing qNMR samples under non-controlled humidity (a conventional method). Additionally, residual ethanol (0.26 ± 0.11%) was observed in the non-PRS ICG. Next, the purity of non-PRS ICG was determined via qNMR when preparing samples under controlled humidity using a saturated sodium bromide solution. The purity was 84.19 ± 0.47% with a lower variation than that under non-controlled humidity. Moreover, ethanol signal almost disappeared. We estimated that residual ethanol in non-PRS ICG was replaced with water under controlled humidity. Subsequently, qNMR analysis was performed when preparing samples under controlled humidity in a constant temperature and humidity box. It showed excellent results with the lowest variation (82.26 ± 0.19%). As the use of a constant temperature and humidity box resulted in the lowest variability, it is recommended to use the control box if the reference ICG standard is needed for JP assays.

Influence of Cable Temperature Rise on PDC Method Test Results of Water Tree Aged Cables

There is a certain temperature rise in the field running cable because of the load bearing. To study the influence of cable temperature rise on the polarization and depolarization current (PDC) method, 10kV XLPE short cables were accelerated aging three months by water needle electrode method, and the PDC method was used to test the new and aged cables under constant humidity. The polarization and depolarization current of the cable samples was analyzed, and the conductivity and low frequency dielectric loss spectra were obtained and inspected. The results show that: in the experiment selected test temperature, the change laws of conductivity of the new and aged cables are the same, and the conductivity gradually rose after a slight drop in 40 °C; in the dielectric loss spectrum, the polarization of the new sample is low and the polarization loss changes little with temperature, and the dielectric loss is mainly affected by the conductivity, so the test result is clearly divided into two regions. And water tree aged samples have strong polarization and are obviously affected by temperature, so their low frequency dielectric loss showed the trend of first rising and then decreasing and the maximum appeared at 60 °C.

Effects of Facial Isometric Exercise on Antioxidant Capacity

Background: Facial isometric exercise is a static contraction of facial muscles without any visible movement in the angle of the joints. To examine the effects of facial isometric exercise on subjective stress and oxidative stress/antioxidant capacity. Methods: In this study, we included 13 participants (6 males, 7 females; average age, 44.8 ± 19.6 years; age range: 20 - 74 years) who were exposed to constant temperature and humidity in a room. Fifteen minutes after entering the room, the force was measured before and after facial isometric exercise of the target muscles: upper lip levator, small zygomatic, large zygomatic, levator animus, laughing, buccal, muzzle, mental, temporal, masseter, and cervical muscles), and further evaluated by comparing the facial isometric exercise group and control (non-facial isometric exercise) group (crossover test). Results: Subjective stress significantly improved by 8.7 ± 16.3 in the facial isometric exercise group, and no significant difference in oxidative stress level was observed in both the groups. However, the antioxidant capacity significantly increased by 126.8 ± 168.1 μmol/l in the facial isometric exercise group. Conclusion: The results of this study suggest that facial isometric exercise is an exercise therapy that can provide mental stability and antiaging effects due to improvement in subjective stress and biological antioxidant potential.

Bio ecological properties and significance of california red worm

The California red earthworm was created as a result of hybridization of different breeds of earthworms in the Eiseniafoet. Red worms are suitable for domestic and industrial cultivation and are also used to feed poultry, fish, animals and fur animals. California worms have the ability to process food faster and more completely than ordinary earthworms. As a result of processing one ton of substrate, the growth of biomass of 600 kg of biohumus and worms reaches 100 kg. California red worms develop over a three-month period and reach sexual maturity. An important factor in their lives is a constant average temperature, humidity and adequate food.

Moisture sorption and thermodynamic properties of Camellia oleifera seeds as influenced by oil content

Moisture sorption isotherms and thermodynamic properties of Camellia oleifera seeds as influenced by oil content were investigated. Moisture desorption and adsorption isotherms of Camellia oleifera seeds, kernels and shells from three varieties were determined using constant temperature and humidity chamber method at different temperatures (10°C, 25°C, and 40°C) with water activity ranging from 0.20 to 0.90. Six selected mathematic models were employed to fit the experimental data. The Peleg model gave the best results for both seeds and kernels and Langmuir model was the best for shells. The difference of equilibrium moisture contents at the same water activities during desorption and adsorption indicated the occurrence of hysteresis of adsorption processes and the equilibrium moisture contents tended to decrease with the increasing oil content and temperature. The binding energy and average capacity per unit mass decreased with increasing temperature and oil content. The relationships between water activity and the logarithm of sorption activity showed the capillary porous body characteristics of the seeds. Keywords: Camellia oleifera seeds, moisture desorption and adsorption isotherms, equilibrium moisture content, oil content, thermodynamic property DOI: 10.25165/j.ijabe.20211401.5457 Citation: Zhu G F, Jin Q, Liu Y H, Lin Y W, Wang J, Li X Y. Moisture sorption and thermodynamic properties of Camellia oleifera seeds as influenced by oil content. Int J Agric & Biol Eng, 2021; 14(1): 251–258.