Connection Point Research Articles

Investigation of the electrical quality and long-term stability of aluminum ground stud connections in automotive applications

The rapid advancement in the electrification of modern vehicles has led to a continuous increase in electrical consumers for various comfort and safety functions. Ground studs serve as the electrical interface between the conductive vehicle body and the onboard network. Drawn arc stud welding is an economical and established joining process for producing ground stud joints. The circuits in the onboard network are increasingly subject to greater demands regarding current-carrying capacity and long-term stability. Reliable signal and power transmission require minimal contact resistance at the electrical connection points of the ground stud system and must withstand various operating and environmental conditions over the entire service life. In this study, a ground stud made of AlMg5, with a ZnNi-coated steel cap nut was used on a 2.0 mm thick sheet of AlMg3. The electrical connection of the ground studs was made using tinned copper cable lugs and 35 mm² cables. To analyze the electrical resistance behavior in an accelerated test, the ground studs were subjected to a superimposed load with a cyclic current profile for 1008 hours under changing climatic conditions. The results show that under the chosen operational and environmental conditions, accelerated aging and intermittent resistance behavior occur. A characteristic drop in resistance during the test indicates the failure point of the electrical connection. The cause of failure can be attributed to media penetration into the electrical contact zone. A failure of the electrical connection was observed after 512 hours.

Dynamic model and characteristic analysis of a combined algebraic spiral scroll compressor

The combined algebraic spiral (CAS) effectively maximizes the geometric performance of a scroll compressor; however, its dynamic behavior remains inadequately explored. Utilizing the geometric model of the CAS scroll compressor, this study derived the functional relationship between the meshing point and the rotation angle, and calculated the working chamber volume using the discrete Green's theorem method. A dynamic model of the CAS scroll compressor was developed, and the influence of various parameters on its dynamic characteristics was analyzed. The findings indicate that when the polar angle interval is less than 0.01π, the discrete Green's theorem method accurately computes the working chamber volume. Among the gas forces acting on the CAS scroll compressor, the axial gas force is the most significant, followed by the tangential gas force, while the radial gas force is considerably smaller. The tangential gas force predominantly influences the overturning and rotational moments. Notably, when the polar angles of the connection points between the higher-order curve and the starting and ending algebraic spirals are set at 1.5π and 3π, the gas force remains low while maintaining geometric performance. This configuration results in reduced variation in gas force and enhanced dynamic performance. The spiral coefficient and spiral index of the starting algebraic spiral should be set as intermediate values to ensure optimal geometric and dynamic performance of the CAS scroll compressor.

A new perspective: Quantitative description of the Cupid’s peak aesthetics essence

ObjectivesThe Cupid's peak triangle theory was established to reveal the aesthetics essence of the Cupid's peak through Gold-ratio deviation, to provide quantitative theoretical basis for lip plastic and cosmetic surgery. Materials and MethodsModel the Cupid's peak line on the lip bow ridge and construct expressions for Cupid's peak parameters and their associated triangle theory using the Angle Circle (AC) and Radius Circle (RC) of the Cupid's peak line. Calculate and establish functional relationships for Cupid's peak parameters and the concept of the Cupid's peak index Golden Ratio Deviation. ResultsIn the Cupid's Peak Triangle Theory, important parameters describing Cupid's peak morphology include Cupid's peak angle (ACp), arc (RCp), the smooth connection point (SI) of the Cupid's peak arc and line, and the Cupid's peak index (CPI). The parameters are interrelated in their functional relationships. ACp determines RCp, the SI point determines the proportion of the Cupid's peak arc to the line, and CPI determines GRD. Cupid's peak parameter ranges in the normal population are as follows: ACp is 109o-160o, RCp is 1.24-0.35 radians, CPI is 0.614-0.508, and GRD is 0.62-17.85%. ConclusionsThe Cupid's peak triangle theory reveals the functional relationship between the Cupid's peak parameters and quantifies the aesthetics essence of lip shape. Clinical RelevanceThe morphology of the Cupid's peak serves as a tangible manifestation of lip shape aesthetics. This study aims to elucidate the aesthetic essence and general principles of Cupid's peak morphology, offering a quantitative theoretical foundation for lip plastic and cosmetic surgery.

Evaluation and convergence analysis of science and technology innovation efficiency in China’s national central cities based on the super-efficiency SBM-ML model

ABSTRACT Scientific and Technological Innovation (STI) is an important driving force for economic development and social progress. National central cities are the main connection points of China’s economic activity network and play a leading role in the national economic development of the country. In order to explore the efficiency of STI and the convergence characteristics of STI in China’s national central cities, this paper selects S&T innovation input-output indicators and constructs a system of indicators for high-quality economic development. It measures the STI innovation efficiency of China’s national central cities by combining with the super-efficiency SBM-ML model and then constructs a model to analyze its convergence situation. The results of the study show that: from 2011 to 2021, the STI efficiency of China’s national central cities has reached an effective level, and the overall trend has increased; the total factor productivity of STI in China’s national central cities has obvious differences, with Beijing having the highest total factor productivity, while Shanghai has the lowest; the STI innovation efficiency of China’s national central cities exhibits both absolute β-convergence and conditional β-convergence, but there is no significant α convergence, and regional differences are obvious.

Research and Application of Flexible Fracturing Manifold in Volumetric fracturing

Abstract In order to solve the problems of high pressure pipe valves in Volumetrictric fracturing, such as large demand of high pressure pipe and valve parts, high pressure manifold for fracturing complex connection, fracturing pipeline connections are complex, long fracturing construction preparation period. The economy and timeliness of pipeline connection seriously affect the speed and efficiency of Volumetrictric fracturing operations. This paper designed and developed the high pressure flexible composite pipe and carried out its performance evaluation test. Combined with Volumetrictric fracturing operation conditions, supporting functional modular manifold system, overcome flexible pipeline and rigid pipeline fast connection technology, flexible fracturing manifold system was formed. Through the large-scale field application in the unconventional reservoir Volumetric fracturing field, The flexible fracturing manifold is compared with the conventional high-pressure pipe valve connection and the single pipe universal connection, the flexible fracturing manifold can reduce the use of high-pressure pipe valves by 1/3, increase the efficiency of fracturing manifold connection by 50%, and reduce the labor intensity by 50%, enables efficient, reduce high pressure manifold connection points by 70%. The timeliness and safety of fracturing manifold connections have been greatly improved. Flexible fracturing manifold fundamentally change the connection mode of Volumetrictric fracturing high-pressure manifold, and realizes the speed and efficiency of reservoir transformation.

Coordinated optimization method of renewable energy sources and energy storage devices based on synergistic capacity short circuit ratio

The traditional short circuit ratio index does not consider the impact of energy storage devices (ESDs) and cannot be used for the collaborative optimization of ESDs and renewable energy sources (RESs). Therefore, this paper proposes a novel synergistic capacity short circuit ratio (SCSCR) index, which can reflect the interaction between multiple RESs and ESDs on each bus under different capacities. Based on the proposed SCSCR, a coordinated optimization method of RESs and ESDs is proposed. It ensures system strength while determining the optimal location and capacity proportion of RESs and ESDs. Firstly, the location and capacity proportion of RESs are obtained through optimization method because the system strength is mainly determined by RESs connection points. Secondly, the optimal location and capacity proportion of the ESDs are found under the optimal configuration of the RESs. The proposed optimization method ensures the system strength while obtaining the optimal location and optimal capacity proportion of RESs and ESDs. Finally, the simulation results verify the effectiveness of this method on the IEEE 9 bus and 39 bus systems, providing reference for the site selection and efficient operation of RESs and ESDs.

ECONOMIC EFFICIENCY OF APPLICATION OF OPTIMIZED MILL BED

This paper presents the selection of optimization parameters for the bed geometry of a long metal cutting machine (MCM), the design problem and boundary conditions were given. Five different geometries were designed for further mathematical analysis to meet the requirements of the problem. Static analysis of the mathematical model of the bed shells was performed by finite element method (FEM) using BETA CAE System tool, ABAQUS, which showed that by using stiffeners in the form of two variable pitch spirals and three hollow tubes, as well as changing the design at the connection point of the beam support to the bollards of the long bed of the metal cutting machine, the stresses that occurred in these places at an angle of 90° were reduced. The geometries were chosen in such a way that it was possible to reduce the stresses occurring at the point of cutting, to reduce the deflection, to increase the rigidity of the structure. The economic calculation aimed at determining the cost of a long metal-cutting machine tool with the proposed geometry has been carried out. The analysis of the unit cost of the product (long bed of the metal-cutting machine tool made of polymer concrete with optimized geometry) has been carried out, the calculation of the annual economic effect from the use of the proposed method of manufacturing has been carried out. Keywords: MCM, FEM, statistical analysis, product cost, economic calculation.

Design and mechanical properties analysis of a novel CFRP tendons anchorage structure

To address the challenges of larger size, stress concentration at the loading end, and insufficient anchoring performance at the free end of traditional bonding-type anchors for Carbon Fiber Reinforced Polymer (CFRP) tendons, a novel anchor featuring a variable angle multi-stage cone is proposed. This solution is derived by analyzing the notch effect at the loading end caused by the wedging of the bonding medium in conventional cone-type anchors. A theoretical model for the stress distribution of the variable angle multi-stage conical anchor was developed using elastic deformation theory. The reliability of this model was validated through finite element analysis. Subsequently, a comparative analysis was conducted to evaluate the stress distribution and anchoring performance of the variable angle multi-stage conical anchor against several traditional anchor types. This analysis revealed the mechanical mechanisms and advantages of the variable angle multi-stage conical anchor in enhancing anchoring effectiveness. The study illustrates that the bonding medium between adjacent cone sections of the variable angle multi-stage conical anchor exhibits a specific gap under stress, leading to reduced stress in the tendon at the connection points. This ensures a smooth transition that prevents abrupt changes in stress due to sudden shape alterations, thereby guaranteeing uniform stress distribution within the anchor section. By incorporating a multi-stage cone structure and increasing the cone angle at the free end, compressive stress can be effectively transferred to the free end, mitigating the notch effect and enhancing anchoring performance. Compared to typical conical anchors, the maximum compressive stress of the variable angle multi-stage conical anchor is reduced by 53.5 %, the outer diameter of the anchor cylinder is decreased by 22.7 %, and the anchoring efficiency is improved by 12.2 %. These improvements result in a robust anchoring effect and significant size advantage. The anchor is suitable for multibar anchoring, providing a reliable solution for large tonnage and long-span cable-stayed bridges.

Effect of Reactive Power Generation in Photovoltaic Installations on the Voltage Value at the Inverter Connection Point

Worldwide, photovoltaic installations are making an increasing contribution to electric energy generation. These are power-unstable sources due to the rapid and frequent change in insolation. As a result, a common problem noted in low-voltage power grids is that the permitted voltage values at the source connection point are exceeded. There are several methods of limiting the voltage values present at the inverter. One of them is the generation of reactive power in a photovoltaic installation. In the literature, one can find many relationships that allow one to determine the increase in voltage caused by the change in reactive power, where the imaginary part of the voltage loss is omitted as insignificant. The authors’ research has shown that this can lead to significant errors. Omitting the imaginary value causes the determined values to be even more than 4.5 times smaller—these differences increase with the length of the line. The analyses carried out by the authors show that the determination of voltage increments with and without taking into account the imaginary part of the voltage loss in the calculations differs from the values determined via computer simulation (failure to take into account the imaginary part results in calculated values of voltage increase being lower than the values determined via a computer by about 40% on average).

Modeling the service life of temporary airfield operational surfaces under multi-pass aircraft trafficking

Expeditionary Airfield (EAF) surfacing systems are designed to create temporary aircraft operating surfaces. Modeling the service life of EAF surfacing systems including the matting system, aircraft, and subgrade, has historically proven difficult, exacerbated by variability between systems and the multitude of mechanisms that can constitute failure. The study presented herein outlines the development and implementation of a performance modeling approach that includes a multi-scale scheme that accounts for local characteristics of the connection points of the EAF matting system, coupled to the global characteristics of the matting array to predict cyclic passes to failure. Finite element studies were conducted for an EAF surfacing system brickwork configuration subjected to aircraft strut loads over varying California Bearing Ratio (CBR) subgrades to calibrate a transfer function to full-scale trafficking experiments. The proposed framework is then used to predict the rate of subgrade deformation for additional lay patterns, which successfully ranked the performance of each relative to full-scale trafficking experiments. An approach is proposed to couple the rate of subgrade deformation with local finite element models to capture increasing joint damage as permanent deformation accumulates, and supplemented by a variable amplitude cycle counting and damage accumulation algorithm that yields reasonable agreement with full-scale experiments while capturing the transition in failure mechanisms at higher CBR values. The results of the study presented herein captures the propensity for end connector and subgrade failure over a range of subgrade CBRs and shows promise for a broader performance framework that can be extended to other EAF surfacing systems, aircraft types, and specific matting lay patterns.

Experimental and numerical study on mounting force and withdrawal strength of self-threaded dowels in particleboard

Traditional and alternative joining techniques have been used for many years at the connection points of structural bearing systems. Especially, glued doweled and screwed type mechanical connections are widely used in wooden structures and furniture constructions. Although there are many studies related to the strength of dowel and screw joints, limited papers describe the practical use of self-threaded dowels (STDs) in the joints. In this study, thread geometry effect of the STDs in particleboard (PB) was investigated by determining the mounting force and withdrawal strength values. For this purpose, STDs including three different thread width (0,2 - 0,3 - 0,4 mm) and two different thread length (1 - 2 mm) were designed, produced and tested under static compressive and tensile forces. All STDs were produced with polylactic acid (PLA) by using Layer Plastic Deposition (LPD) method in 3D printing technology. Uniaxial compression tests were performed in order to determine the minimum mounting force while the tension tests were performed for determining the maximum withdrawal force required to put the STDs into the hole and pull out them, respectively. Numerical analysis (FEM) were used to analyze the contact pressures and stresses of the STD joints. Abaqus v6.13-1 software was utilized for the numerical analyses. In addition, multiple regression analysis was carried out to predict the mounting force and withdrawal strength of the STDs. Results showed that the predictive expressions developed provided reasonable estimates for mounting force and withdrawal strength of STDs. According to the statistical analyses; thread width, thread length and their interaction have significantly affected both mounting force and withdrawal strength of STDs. At the end of the experimental and numerical tests, STDs with 0,2 mm width and 2 mm length threads gave the lowest mounting force values, stresses and contact forces. However, the highest withdrawal strength values were obtained from the STDs with 0,3 mm width and 1 mm length threads. According to the results of the study, the optimum STD was the one with 0,3 mm thread width and 2 mm thread length. In conclusion, the STDs can be utilized as an alternative fastener to the conventional glued dowel type joints in PB. However, corner joints constructed of different kinds of wood-based composites and connected with the STDs should be investigated in the future studies.

Optimization of Clamping and Conveying Parameters for Spinach Orderly Harvesting with Low Damage by Simulation and Experiment

The leaves of spinach are delicate and easily injured during harvesting. To reduce the spinach damage rate and increase the conveyance success rate, an orderly harvester was designed and manufactured, and the key conveying parameters of the harvester were optimized by simulation and experiments. The compression damage stress of spinach was determined by compression tests. Then, a finite element simulation model for spinach clamping was established, and the influence of different clamping heights on the spinach deformation and equivalent stress were simulated and analyzed. Finally, response surface Box–Behnken experiments were conducted to optimize the combinations of the twisting angle, clamping distance, and height difference. The results of the compression tests showed that the compression damage stresses of spinach leaves, stems, and their connection points were 8.04 × 10−2 MPa, 7.85 × 10−2 MPa, and 11.63 × 10−2 MPa, respectively. The optimal clamping height of spinach for orderly conveyance was obtained to be 20 mm according to the finite element simulation. The response surface experimental results indicated that the significance order of factors affecting the extrusion force was the clamping distance, the height difference, and the twisting angle. The significance order of factors affecting the conveyance success rate was the clamping distance, the twisting angle, and the height difference. The optimal parameter combination was ae twisting angle of 60°, clamping distance of 24 mm, and a height difference of 20 cm. The experimental validation of the optimization results from the finite element simulation and response surface tests demonstrated that the extrusion force and conveyance success rate were 2.37 N and 94%, respectively, with a conveying damage rate of 3% for spinach, meeting the requirements for the low-damage and orderly harvesting of spinach.

Modular Hemipelvic Prosthesis Preserves Normal Biomechanics and Showed Good Compatibility: A Finite Element Analysis.

This study aimed to evaluate the biomechanical compatibility of a modular hemipelvic prosthesis by comparing stress distributions between an implanted pelvis and a healthy pelvis. Finite element analysis was used to simulate bilateral standing loads on both models, analyzing critical regions such as the sacroiliac joints, iliac crest, acetabulum, and prosthesis connection points. Six models with varied displacements of the hip joint rotational center were also introduced to assess the impact of deviations on stress distribution. The implanted pelvis had a stress distribution closely matching that of the intact pelvis, indicating that the prosthesis design maintained the biomechanical integrity of the pelvis. Stress patterns in displacement models with deviations of less than 10 mm were similar to the standard model, with only minor changes in stress magnitude. However, backward, upward, and inward deviations resulted in stress concentrations, particularly in the prosthesis connection points, increasing the likelihood of mechanical failure. The modular hemipelvic prosthesis demonstrated good biomechanical compatibility with minimal impact on pelvic stress distribution, even with moderate deviations in the hip joint's rotational center; outward, forward, and downward displacements are preferable to minimize stress concentration and prevent implant failure in cases where minor deviations in the rotational center are unavoidable during surgery.

Automated packing and piping in an Airbus A320 main landing gear bay: an industrial development case study

The packing of given hydraulic equipment together with the hydraulic piping is a challenging design task. Both the hydraulic domain and the geometry domain are highly intercoupled as the packing determines the exact location of the connection points and tangents for the pipes but also defines the installation spaces for the equipment to be positioned which needs to be taken into account as an obstacle during the piping process. For the industrial case study, a mounting rack in an Airbus A320 main landing gear bay is used, where seven pieces of equipment should be packed and 22 pipes should be routed. In the first part of the study, the packing was done manually, assisted by automated routing, while the hydraulic piping was generated automatically. In the second part of the study the packing was automatized as well. For the automated packing process, a particle multi swarm optimisation was used. As objective function a pipe length minimization was implemented, which uses the Dubins Path as a pipe approximation. Constraints taken into account are the collision-free nature of the equipment and its placement on a plate inside the plates borders. The automated packing workflow was used to generate different variants of which for two a pipe work was generated exemplarily. Due to the model-based systems engineering approach, no further interaction in terms of the definition of the connection points, tangents and the installation space is necessary. This demonstrates that an automated packing and piping process in an industrial context using industrial geometries is now feasible.

Entanglement enhancement of two giant atoms with multiple connection points in bidirectional-chiral quantum waveguide-QED system

We study the entanglement generation of two giant atoms within a one-dimensional bidirectional-chiral waveguide quantum electrodynamics (QED) system, where the initial state of the two giant atoms are ∣e a , g b 〉. Here, each giant atom is coupled to the waveguide through three connection points, with the configurations divided into five types based on the arrangement of coupling points between the giant atoms and the waveguide: separate, fully braided, partially braided, fully nested, and partially nested. We explore the entanglement generation process within each configuration in both nonchiral and chiral coupling cases. It is demonstrated that entanglement can be controlled as needed by either adjusting the phase shift or selecting different configurations. For nonchiral coupling, the entanglement of each configuration exhibits steady state properties attributable to the presence of dark state. In addition, we find that steady-state entanglement can be obtained at more phase shifts in certain configurations by increasing the number of coupling points between the giant atoms and the bidirectional waveguide. In the case of chiral coupling, the entanglement is maximally enhanced compared to the one of nonchiral case. Especially in fully braided configuration, the concurrence reaches its peak value 1, which is robust to chirality. We further show the influence of atomic initial states on the evolution of interatomic entanglement. Our scheme can be used for entanglement generation in chiral quantum networks of giant-atom waveguide-QED systems, with potential applications in quantum networks and quantum communications.

263 Public perspectives of calf handling: A survey of Canadians

Abstract In North American beef production handling and restraint of young calves is integral to animal welfare and management practices. This study used a mixed method approach to gather public perceptions of three handling and restraint methods common on beef operations in western Canada (RW - Roping and Wrestling, NF – roping and NordForks, and TT – Tilt Table). Canadian participants (n = 551) recruited by CloudResearch to represent the national demographics participated in an online survey that included videos of each handling method to ascertain preferences and acceptability. Prior to watching the videos, participants were given industry information about handling and restraint or generic information regarding hay as a control information statement within the topic of agriculture. The survey also collected information about knowledge of the beef industry, animal welfare, and empathy toward animals. The reasons for preferences were described as presence of a perceived positive attribute and absence of a perceived negative for most preferred methods, and inversely when explaining least preferred method. The findings focused on calf’s experience, perception of handler actions, and pragmatic balancing of handler needs and a good life for the calf. Methods were rated as more acceptable for participants that ate meat consistently, knew more about the beef industry, and, to a lesser extent, if the individual had a lower animal empathy score (Table 1). Acceptability was not affected by providing information about the practices; however, information about handling and restraint did elicit more pragmatic reasoning. Most participants preferred TT over NF and RW (P < 0.001) and found TT more acceptable as well (P < 0.001). The TT was the most preferred method due to calf experience and human handling, notably the absence of dragging a calf, which was predominant in why participants selected NF or RW as their least preferred method. Consistency of themes highlights that the Canadian public has a fundamental expectation of value for the quality of life of the calf, humane handling, and pragmatism which aligns with beef sustainability initiatives and represent points of connection for building trust between industry and the public.

‘Handing down of beautiful knowledge’: Yarning with workers about feeding practices and mealtimes in Australian First Nations families

Mealtimes and feeding practices are shaped by culture and have long-term implications for social and emotional wellbeing. To date, there has been little research in Australia that has focused on First Nations families' feeding practices and mealtimes. This co-designed study aimed to explore First Nations' families feeding practices through yarning circles with workers (n = 14) at an Aboriginal Community Controlled Organization. Most workers (79%) were Aboriginal and/or Torres Strait Islander and all worked directly with First Nations families. Using thematic analysis, four themes were inductively identified from the yarns: the importance of childhood experiences, history, and intergenerational knowledges; mealtimes as a point of connection and wellbeing; the impact of structural barriers on feeding practices; and the important roles of First Nations workers supporting families with feeding difficulties. Workers described how First Nations families' feeding practices and mealtimes are informed by cultural values and knowledge that have been passed down through generations. Yet throughout the yarns, participants highlighted the impact of historical and current structural factors (e.g., cost of living, child removal, housing) that affect families' ability to engage in feeding practices that align with their beliefs and culture. Workers described several strengths-based approaches they use to support families, including community-led mealtime groups, liaising with mainstream health services, and providing a respectful space. We propose that the Social and Emotional Wellbeing model is a holistic strengths-based resource for workers to conceptualize First Nations families’ strengths, values, and challenges in relation to feeding and mealtimes. More co-designed research including the perspectives of First Nations families is needed to better understand healthy and culturally aligned feeding and mealtime practices.

Optimal control strategies for energy storage systems for HUB substation considering multiple distribution networks

With the global consensus to achieve carbon neutral goals, power systems are experiencing a rapid increase in renewable energy sources and energy storage systems (ESS). Especially, recent development of hub substations (HS/S) equipped with ESS, applicable for resolving site constraints if implemented as mobile transformers, is expanding the development of ESS-equipped facilities. However, these units require centralized control strategies considering variability within integrated networks. While studies on electric vehicle charging considering the variability of renewable energy or load are widely studied, ESS management scheme for individual substations requires further optimization, especially considering the state of distributed sources at lower levels and transmission system operators. Thus, in this study, an optimal control approach for ESS located at the connection point of transmission and distribution systems, including further consideration of the loss in distribution lines and the constraints of renewable energy sources is presented. This study attempts to derive proactive control strategies for ESS in HS/S to operate with various distribution networks. By establishing control priorities for each source through optimal operation strategy, a suitable capacity of ESS and its economic benefits for distribution network management can be examined. Validation of the current analysis results is performed by utilizing MATPOWER. By adapting the operational range of design scenarios, diverse distribution systems can be tested against multiple configurations of connected devices.

Identification of potential biological corridors for the bobcat (Lynx rufus) in a multipurpose area of northeastern Mexico

The objectives of the research were i) to determine patches and points of origin forthe establishment and connectivity of biological corridors, ii) to estimate the costarea for the establishment of biological corridors, iii) to define biological corridorswith viability for the dispersal of the bobcat (Lynx rufus) in a multipurpose area inReynosa, Tamaulipas. To monitor behavioral patterns, capture and recapturerecords were generated using the photographic sampling method. To calculatedensity, the results were entered into the statistical program CAPTURE. To modelthe potential habitat, the maximum entropy method (MaxEnt) was used. The costsurfaces were obtained with the maps in MaxEnt. The results showed that: i) thereare six patches and points of origin for the establishment and connectivity ofbiological corridors, which presented a mature community of Tamaulipanthornscrub, ii) most of the study area presents values ranging from medium to highon the cost scale, which is correlated with intense landscape modification, and iii)11 potential biological corridors were defined for the dispersal of the bobcat (Lynxrufus) in a multipurpose area in Reynosa, Tamaulipas.

Advancing Graduate Leadership Education for Institutional Alignment

Building a future pipeline of leaders in higher education remains a topic of importance given the challenges and pressures facing colleges and universities. The current article introduces one initiative dedicated to graduate leadership education, the PreDoctoral Leadership Development Academy at Rutgers University, and highlights points of connection to other similar national programs. In response to the symposium theme, we advance three linkages to the power of place, including an emphasis on graduate leadership education as (1) a shared or collective endeavor, (2) a reflection of institutional values, and (3) a laboratory for analyzing organization‐specific challenges and opportunities.