Low Temperature Conditions Research Articles

Influence of Few-Layer Graphene on Frictional Properties of Lithium Compound Grease

The frictional properties of lithium compound grease (LCG) with different percentage compositions of few-layer graphene (FLG) were investigated, and the mechanisms of temperature and loading effects on LCG containing FLG are also considered. The concluding effect shows that 1 wt% FLG is more appropriate for friction and wear modifiers for lithium compound grease at elevated temperatures and less suitable at ordinary temperatures. Thickener chemisorption film, FLG layering film, and tribo-reaction film consisting of FeO(OH), Fe2O3, Fe3O4, Li2O, and other oxides assist in the establishment of a lubricating boundary film on the friction interfaces lubricated with LCG containing FLG. The poor fluidity of lithium compound grease at low temperatures leads to poor dispersion of FLG, decreasing friction reduction capability. Under elevated temperature and low load condition, adding 1wt% FLG to LCG can only improve its wear-resistant property, the abrasion volume of steel plate reduced by 24.49%. Under elevated temperature and high load condition, adding 1wt% FLG to LCG can only enhance its anti-friction characteristics.. Conversely, FLG is unsuitable as an anti-friction and wear-resistant additive for LCG at low-temperature conditions.

Thermal-hydro coupling model of methane hydrate reformation in porous media

Methane hydrates are crystalline compounds found in marine sediments and permafrost regions. Methane hydrates remain stable under both low-temperature and high-pressure conditions. When a methane hydrate reservoir is heated or depressurized, methane hydrates become unstable and decompose into water and methane gases. The heat absorption process during the decomposition of methane hydrates influences the temperature field. Methane hydrate reformation occurs during the extraction process, significantly reducing the hydraulic conductivity of the reservoir and hindering the long-term stable extraction of methane hydrates. In this paper, a numerical model is established by coupling seepage and heat processes. The temperature variation owing to the heat absorption process of methane hydrate decomposition is quantified based on the proposed model. The effect of spatial lithology on methane hydrate conversion is also analyzed, and the results for hydrate, water, gas, and permeability in the model are summarized. The numerical model also reflects the heterogeneity of marine sediments. Finally, the sensitivities of different physical parameters (permeability and porosity) and pressure gradients to the reformation rate of methane hydrate reforming are discussed. The results of this study provide scientific data supporting the influence of secondary hydrate formation on long-term extraction efficiency in the actual engineering hydrate extraction process.

Low temperature (002)-oriented zinc oxide films prepared using ozone-based spatial atomic layer deposition

In this study, ZnO films are prepared at a low temperature of 150 °C by using spatial atomic layer deposition (sALD) with diethylzinc and ozone as precursor and oxidant. The ozone flow rate is varied to systematically investigate its effect on optical, structural and electrical properties. The experimental results show that the self-limiting surface reactions can occur at the low ozone flow rate of 200 sccm, confirming ALD growth mode. All the ozone flow rates lead to ZnO (002) crystalline orientation, which is difficult to be obtained for conventional water-based ALD ZnO films at the low temperature. The increased ozone flow rate results in an increased amount of oxygen vacancies, enhanced carrier concentration and a reduced stress. The resistivity and carrier concentration can be tuned in the range of 4.75–0.08 Ω-cm and (1.1–5.5) × 1018 cm−3. Finally, the sALD ZnO film on polyethylene terephthalate reveals a high stability in the film property against bending. This study is beneficial for the utilization of ZnO films in optoelectronic devices that demand the (002) preferred orientation, especially under low-temperature conditions.

Effects of Blood Flow Restricted Resistance Exercise on Recovery Blood Flow under Various Environmental Temperature Conditions

OBJECTIVES This study examines the impact of blood flow restriction (BFR) resistance exercise on blood flow across varying environmental temperatures, aiming to understand the physiological responses, exercise function, and recovery process affected by temperature changes.METHODS Seven healthy males (age: 26.4±1.7 years, weight: 72.7±6.8 kg, height: 174.5±2.0 cm) participated in biceps brachii exercises with and without BFR under low (10°C/25% humidity), moderate (25°C/50% humidity), and high (40°C/50% humidity) environmental conditions. Each participant completed six sessions of exercise across these conditions to assess the recovery phase blood flow changes. Blood flow measurements were taken during the recovery phase for analysis.RESULTS Blood flow significantly increased in high-temperature conditions, independent of BFR application, showing notable differences compared to low-temperature conditions (<i>p</i><.05).CONCLUSIONS Environmental temperature significantly affects blood flow changes during BFR resistance exercise, with increased blood flow in high temperatures indicating a physiological adaptation to thermal stress. This suggests the need to consider environmental temperatures in optimizing BFR exercise protocols.

Influence of some abiotic factors on the apple stressassociated protein gene expression profiles

In plants, stress-associated proteins (SAP) play a crucial role in responding to adverse biotic and abiotic factors. In this study, we evaluated the expression profiles of 14 apple SAP genes (MdSAP) under the influence of low and high temperatures, as well as salinity, using the quantitative polymerase chain reaction (qPCR). The results showed that the most significant changes in expression levels were observed in the genes MdSAP11, MdSAP2, and MdSAP3 under high temperature conditions, MdSAP1, MdSAP2, MdSAP4, and MdSAP6 under low temperature conditions, and MdSAP1, MdSAP8, and MdSAP11 under salt stress. Furthermore, there was a tendency for gene expression to increase at 2 and/or 4 hours of exposure followed by a decrease at 24 hours. The analysis of the correlation between the expression levels of MdSAP genes revealed both positive and negative linear relationships.These findings will help elucidate the specific roles of individual SAP genes in shaping the apple stress response to low and high temperatures, as well as salinity.

Identification and characterization of STAT family in silver pomfret (Pampus argenteus) involved in different exogenous stresses

Members of the Signal Transducer and Activator of Transcription (STAT) family function pivotally as transcriptional activators integral to the modulation of inflammatory responses. The aquaculture of silver pomfret is frequently compromised by the imposition of exogenous stressors, which include thermal fluctuations, notably low-temperatures, diminished oxygen levels, and the onslaught of bacterial pathogens. Notwithstanding the critical impact of these stressors, the scientific literature presents a notable gap in our understanding of the STAT pathway's role in the silver pomfret's adaptive response mechanisms. To address this lacuna, we identified stat genes in the silver pomfret—denominated as Pastat1, Pastat2, Pastat3, Pastat4, and Pastat5—through a thorough and systematic bioinformatics analysis. Further scrutiny of the gene configurations and constituent motifs has elucidated that STAT proteins possess analogous structural frameworks and exhibit significant evolutionary preservation. Subsequently, the expression patterns of five stat genes were verified by RT-qPCR in twelve different tissues and four growth periods in healthy fish, showing that the expression of Pastat genes was temporally and spatially specific, with most of the stat genes expressed at higher levels in the spleen, following muscle, gill, and liver. Transcriptomic analysis of exposure to exogenous stressors, specifically formaldehyde and low-temperature conditions, elucidated that Pastat1 and Pastat2 genes exhibited a heightened sensitivity to these environmental challenges. RT-qPCR assays demonstrated a marked alteration in the expression profiles of jak1 and Pastat gene suites in PaS upon prolonged bacterial infection subsequent to these exogenous insults. Moreover, the gene expression of the downstream effectors involved in innate immunity and apoptosis displayed marked deviations. This study additionally elucidated the Pastat gene family's role in modulating the innate immune response and apoptotic regulation within the silver pomfret during exogenous stressors and subsequent pathogenic incursions.

PROSPECTIVE LITHIUM ALUMINOSILICATE GLASS-CERAMIC MATERIALS FOR PULSE RANGEFINDERS

The relevance of creating multi-functional nanosecond pulsed laser devices with a generation wavelength that lies in the conditionally eye-safe region of the spectrum of 1.5÷1.6 μm has been established. The prospects of using the mode of passive Q-switching when receiving powerful nanosecond laser pulses with a radiation divergence close to the diffraction one have been determined. Materials for shutters that function in the mode of passive Q-switching were analyzed: solid-state nonlinear optical materials based on single crystals of yttrium-aluminum garnet doped with cations of neodymium, chromium, vanadium and other Nd- or Yb-doped crystals in the wavelength range of 0.8–1.2 μm. The promising use of oxide single crystals activated by Co2+ ions in four-coordinated oxygen positions for MgAl2O4, LiGa5O8, LaMgAl11O19 has been confirmed. The feasibility of developing transparent glass-ceramics based on aluminomagnesium and lithium gallium spinel for pulsed ranging was determined, taking into account its commercial availability, the simplicity of the production technology, as well as the homogeneity of the distribution of the activator in the volume. The feasibility of creating a new type of nonlinear optical materials based on nanostructured heat-resistant lithium aluminosilicate glass ceramics with spinel nanocrystals activated by Co2+ ions under low-temperature heat treatment conditions, has been determined. The purpose and tasks of the work are formulated, which consist in justifying the choice of the system and compositions of glasses for obtaining glass-ceramic materials as a passive laser shutter for powerful lasers that operate at a wavelength of 1.54 μm and are characterized by high heat resistance. The choice of the lithium aluminosilicate system R2O – RO – RO2 – P2O5 – R2O3 – SiO2 based on phase-forming SiO2, Al2O3, Li2O, modifying K2O is substantiated; RO – MgO, ZnO, CaO, SrO, BaO components and a complex crystallization catalyst of P2O5, CeO2, TiO2, SnO2, ZrO2 and ZnO. The structural criteria for the glass matrix were formulated. Compositions of model glasses were designed taking into account the calculated parameters fSi > 0.22, Kсr ≥ 3.5, Ktr ≥ 2.1, and the probability of obtaining transparent glass-ceramic materials with a sitallized structure for pulse rangefinders was established on their basis.

Chemical Approach to Control Hydrate in Offshore Gas Production Facilities

- Hydrate formation presents a significant operational challenge in offshore oil and gas production, primarily due to the potential formation of hydrate plugs which obstruct fluid flow, thereby posing serious flow assurance risks. Additionally, these solid, crystalline, icelike structures, composed of low molecular weight gases (such as methane, ethane, and propane) encapsulated in hydrogen-bonded water cages, can aggregate into larger masses capable of damaging or rupturing pipelines. Such formations typically occur under the high-pressure and low-temperature conditions prevalent in subsea flowlines and cold-weather operations. This study employs the Prosper simulation software to model these complex thermodynamic and hydrodynamic conditions and to predict the effective dosages of chemical inhibitors required to prevent hydrate formation. Specifically, our simulations suggest optimal dosages of 35% wt. methanol (MeOH) and 45% wt. monoethylene glycol (MEG) for gas stream 1, and 22% wt. MeOH and 33% wt. MEG for gas stream 2. Based on these findings, we advocate the use of Prosper simulation software as a predictive tool for the strategic administration of hydrate inhibitors in offshore gas production facilities. This research contributes to the ongoing development of chemical strategies for hydrate management, providing a basis for improved safety and efficiency in hydrocarbon extraction processes.

A hydrate reservoir renovation device and its application in nitrogen bubble fracturing

Abstract. Natural gas hydrate (GH) is a significant potential energy source due to its large reserves, wide distribution, high energy density, and low pollution. However, the gas production rate of past gas hydrate production tests is much lower than the requirement of commercial gas production. Reservoir stimulation technologies like hydraulic fractures provide one potential approach to enhance gas production from GH. The reservoir reformation behavior of the hydrate-bearing sediments (HBSs), particularly sediments with a high clay content, is a complex process during a hydraulic fracturing operation which has been poorly understood and thus hardly predictable. This paper presents an experimental facility that was developed to analyze the hydraulic fracture mechanism in synthesized HBSs. This facility can be used to form GH in sediments, conduct visual observation of hydraulic fracturing experiments, and measure the permeability of HBSs under high-pressure (up to 30 MPa) and low-temperature conditions (from 253.15 to 323.15 K). It is mainly composed of a pressure control and injection unit, a low temperature and cooling unit, a cavitation unit, a visual sapphire reactor, and a data acquisition and measurement unit. The hydraulic fracture module consists of a gas cylinder, fracturing pump, hopper, proppant warehouse, and valves. The sapphire reservoir chamber is applied to observe and measure the fracture of HBSs during hydraulic fracturing. The permeability test module is composed of a constant-flux pump and pressure sensors, which can evaluate the permeability performance before and after the hydraulic fracture in HBSs. The fundamental principles of this apparatus are discussed. Some tests were performed to verify hydraulic fracture tests, and permeability tests could be practically applied in the HBS exploitation.

Shear behavior of cement-stabilized silty clay exposed to low-temperature curing

Cement-stabilized soils are widely used in civil engineering applications. However, they inevitably encounter low-temperature curing conditions, particularly in cold regions. In this study, shear experiments were conducted on cement-stabilized silty clays with different dry densities, cement contents, curing ages and temperatures. The factors influencing the shear performance of cement-stabilized soils were analyzed. The results showed that the peak value of the shear stress-displacement curve of the cement-stabilized silty clay increased with the vertical pressure, and the failure patterns for soils with and without cement significantly differed. Generally, the soils without cement underwent ductile failure, whereas the cement-stabilized soils experienced brittle failure. The shear strength and cohesion of the cement-stabilized soils increased with cement content, dry density, curing age and temperature. In addition, the ice and hydration products significantly influenced the internal friction angle of the cement-stabilized soils. An optimal cement content for silty clay was determined to obtain the largest internal friction angle, which ranged from 12% to 15%. Furthermore, at the curing temperature of −2 °C, the edge-face contact form accounted for the majority with a relatively high porosity, but the morphology of C-S-H changed from a sheet-like form to reticulate structure when the curing temperature increased to 22 °C. However, the contribution of the ice crystals to the shear strength was less significant than that of the hydration products. This study provides insights into the mechanical and microstructural properties of cement-stabilized soils in cold-region geotechnical construction.

Climatic and anthropogenic forcing of vegetation change at different altitudes on the northeastern Tibetan Plateau over the past millennium

The alpine grasslands and meadows of the Tibetan Plateau are critical for maintaining biodiversity, carbon storage, and regional ecological balance. However, the ecological response of the Tibetan Plateau to climate change and anthropogenic activity is poorly understood. We selected two alpine lakes at different altitudes on the northeastern Tibetan Plateau and used n-alkanes from lacustrine sediments to probe the process of ecological response to climate change (temperature and precipitation) during typical climatic periods of the past millennium, as well as impacts on the ecosystem caused by anthropogenic activities. Our results showed that mid- and long-chain n-alkanes in Lake Dalzong and Lake Bihu sediments, which could be used to evaluate plant biomass variations, were mainly derived from terrestrial plants around the watershed. For both the low-altitude Lake Dalzong (3120 m above sea level (a.s.l.)) and the high-altitude Lake Bihu (4360 m a.s.l.), plant biomass of the watershed increased with enhanced temperature and precipitation during the Medieval Warm Period (MWP), whereas they decreased during the Little Ice Age (LIA), under conditions of lower temperature and precipitation. A further comparison with regional climatic records indicates that temperature and precipitation may have played a more important role in plant biomass changes in the low- and high-altitude regions in the northeastern Tibetan Plateau, respectively. In addition, during the Current Warm Period (CWP), when temperature and precipitation were higher than that in the MWP, plant biomass was lower than that in the MWP in both the Lake Dalzong and Lake Bihu watersheds. The intensification of regional grazing activities and the increase in religious rituals were the primary factors contributing to CWP vegetation degradation. This study highlights the fact that a progressively warmer and wetter climate will not offset the negative impacts of anthropogenic activities on vegetation.

Study on the estradiol degradation gene expression and resistance mechanism of Rhodococcus R-001 under low-temperature stress

Estradiol (E2), an endocrine disruptor, acts by mimicking or interfering with the normal physiological functions of natural hormones within organisms, leading to issues such as endocrine system disruption. Notably, seasonal fluctuations in environmental temperature may influence the degradation speed of estradiol (E2) in the natural environment, intensifying its potential health and ecological risks. Therefore, this study aims to explore how bacteria can degrade E2 under low-temperature conditions, unveiling their resistance mechanisms, with the goal of developing new strategies to mitigate the threat of E2 to health and ecological safety. In this paper, we found that Rhodococcus equi DSSKP-R-001 (R-001) can efficiently degrade E2 at 30 °C and 10 °C. Six genes in R-001 were shown to be involved in E2 degradation by heterologous expression at 30 °C. Among them, 17β-HSD, KstD2, and KstD3, were also involved in E2 degradation at 10 °C; KstD was not previously known to degrade E2. RNA-seq was used to characterize differentially expressed genes (DEGs) to explore the stress response of R-001 to low-temperature environments to elucidate the strain's adaptation mechanism. At the low temperature, R-001 cells changed from a round spherical shape to a long rod or irregular shape with elevated unsaturated fatty acids and were consistent with the corresponding genetic changes. Many differentially expressed genes linked to the cold stress response were observed. R-001 was found to upregulate genes encoding cold shock proteins, fatty acid metabolism proteins, the ABC transport system, DNA damage repair, energy metabolism and transcriptional regulators. In this study, we demonstrated six E2 degradation genes in R-001 and found for the first time that E2 degradation genes have different expression characteristics at 30 °C and 10 °C. Linking R-001 to cold acclimation provides new insights and a mechanistic basis for the simultaneous degradation of E2 under cold stress in Rhodococcus adaptation.

A Fully Methylated Cyclic Ether Solvent Enables Graphite Anode Cycling at Low Temperatures.

Graphite anode suffers from great capacity loss and larger cell polarization under low-temperature conditions in lithium-ion batteries (LIBs), which are mainly caused by the high energy barrier for the Li+ desolvation process and sluggish Li+ transfer rate across the solid electrolyte interface (SEI). Regulating an electrolyte with an anion-dominated solvation structure could synchronously stabilize the interface and boost the reaction kinetics of the graphite anode. Herein, a highly ionic conductive electrolyte consisting of a fully methylated cyclic ether solvent of 2,2,4,4,5,5-hexamethyl-1,3-dioxolane (HMD) and fluoroethylene carbonate (FEC) cosolvent was designed. The high electron-donating effect and steric hindrance of -(CH3)2 in HMD endow the HMD-based electrolyte with high ionic conductivity but lower coordination numbers with Li+, and an anion-dominated solvation structure was formed. Such configuration can accelerate the desolvation process and induce the forming of a LiF-rich SEI film on the anode, avoiding the solvent coembedding into graphite and enhancing the ion migration rate under low temperatures. The assembled Li||graphite cell with the tame electrolyte outperformed the conventional carbonates-based cell, showing 93.8% capacity retention after 227 cycles for the DF-based cell compared to 64.7% after 150 cycles. It also exhibited a prolonged cycle life for 200 rounds with 81% capacity retention under -20 °C. Therefore, this work offers a valuable thought for solvent design and provides approaches to electrolyte design for low-temperature LIBs.

Ammonia coverage ratio control of a novel two-cell SCR-DeNOX system configuration based on IA-ISMC

To respond the China’s “14th Five-Year Plan” on the control of nitrogen oxides (NOX) emission, urea-based selective catalytic reduction (SCR) system has been widely applied to reduce the NOX emission from the diesel engine. NO2 is no longer a factor to be ignored while refining the SCR-DeNOX system model because of the ship diesel engine's long-term low temperature and oxygen-rich condition, which provides abundant conditions for the creation of NO2. Therefore, a refined eight-state two-cell SCR-DeNOX model is established in this paper. Meanwhile, the trade-off between NOX emission and tailpipe ammonia (NH3) slip is one of the major challenges which SCR-DeNOX system is facing. While meeting NOX emission standards, the requirement of limiting NH3 slip to prevent secondary pollution is becoming increasingly urgent, which needs a better structure or controller. Therefore, a two-cell SCR-DeNOX system with a by-pass valve in front of the NH3 injection is designed, integral sliding mode control based on inversion algorithm (IA_ISMC) is proposed for each cell. Based on the FTP-75 test cycle, there are three points of view are presented. Firstly, compared with the traditional six-state model, simulation results from the refined eight-state SCR-DeNOX model are closer to the experimental data. Secondly, the introduction of the by-pass structure has a mild impact on the NOX conversion efficiency, but can largely limit the NH3 slip. Finally, the controller based on IA_ISMC effectively improves the tracking performance of NH3 coverage ratio and reduces the cost of NH3 injection. To sum up, the refined two-cell SCR-DeNOX system with a by-pass valve based on IA_ISMC can enhance SCR performance and lower costs.

Optimized combination of room-temperature formability and high-temperature creep property in a dilute-alloyed Mg sheet via tailoring Nd solute segregation

The synergy of room-temperature formability and high-temperature creep property has been a long-term problem in the manufacturing of Mg alloy sheets. Aiming at saving rare-earth resource and providing a widely applicable approach to realize the synergy, this study focuses on the effects of preparation conditions on these two properties in Mg alloyed by dilute Nd (0.8 % in weight percent). Through comparing the mechanical behaviors of the samples prepared by different treatments, including low-temperature and long-time solution (Sample #1), high-temperature and short-time solution (Sample #2), and hot deformation for grain refinement (Sample #3), the best combination of stretch formability and creep property was successfully achieved in the Sample #1. The key reason was the conspicuous Nd solute segregation along grain boundaries after solution treated under the low-temperature and long-time condition. Such segregation behavior allowed dislocations moving freely in grain interiors but inhibited dislocations moving across grain boundaries. Finally, the stretch formability related to free dislocation slip in grain interiors and the creep property related to strong grain boundaries were synchronously enhanced. Thus, the low-temperature and long-time solution treatment is recommended for developing dilute Mg–Nd based alloy sheet used in the environment of alternating temperature changes.

Temperature-driven coordination of circadian transcriptional regulation.

The circadian clock is an evolutionarily-conserved molecular oscillator that enables species to anticipate rhythmic changes in their environment. At a molecular level, the core clock genes induce circadian oscillations in thousands of genes in a tissue-specific manner, orchestrating myriad biological processes. While previous studies have investigated how the core clock circuit responds to environmental perturbations such as temperature, the downstream effects of such perturbations on circadian regulation remain poorly understood. By analyzing bulk-RNA sequencing of Drosophila fat bodies harvested from flies subjected to different environmental conditions, we demonstrate a highly condition-specific circadian transcriptome: genes are cycling in a temperature-specific manner, and the distributions of their phases also differ between the two conditions. Further employing a reference-based gene regulatory network (Reactome), we find evidence of increased gene-gene coordination at low temperatures and synchronization of rhythmic genes that are network neighbors. We report that the phase differences between cycling genes increase as a function of geodesic distance in the low temperature condition, suggesting increased coordination of cycling on the gene regulatory network. Our results suggest a potential mechanism whereby the circadian clock mediates the fly's response to seasonal changes in temperature.

A catalytic membrane approach as a way to obtain sweet and unsweet lactose-free milk.

The growing need in the current market for innovative solutions to obtain lactose-free (L-F) milk is caused by the annual increase in the prevalence of lactose intolerance inside as well as the newborn, children, and adults. Various configurations of enzymes can yield two distinct L-F products: sweet (β-galactosidase) and unsweet (β-galactosidase and glucose oxidase) L-F milk. In addition, the reduction of sweetness through glucose decomposition should be performed in a one-pot mode with catalase to eliminate product inhibition caused by H2O2. Both L-F products enjoy popularity among a rapidly expanding group of consumers. Although enzyme immobilization techniques are well known in industrial processes, new carriers and economic strategies are still being searched. Polymeric carriers, due to the variety of functional groups and non-toxicity, are attractive propositions for individual and co-immobilization of food enzymes. In the presented work, two strategies (with free and immobilized enzymes; β-galactosidase NOLA, glucose oxidase from Aspergillus niger, and catalase from Serratia sp.) for obtaining sweet and unsweet L-F milk under low-temperature conditions were proposed. For free enzymes, achieving the critical assumption, lactose hydrolysis and glucose decomposition occurred after 1 and 4.3h, respectively. The tested catalytic membranes were created on regenerated cellulose and polyamide. In both cases, the time required for lactose and glucose bioconversion was extended compared to free enzymes. However, these preparations could be reused for up to five (β-galactosidase) and ten cycles (glucose oxidase with catalase).

Research on the Mechanical Properties of Concrete under Low Temperatures.

As construction projects in cold regions continue to increase, it has become necessary to understand the performance of concrete at low temperatures. Conducting uniaxial compressive tests on non-standard prismatic concrete specimens under low-temperature conditions and analyzing the test results allows for a comprehensive understanding of the strength variations of concrete with different strength grades at temperatures of 20 °C, 0 °C, -20 °C, -30 °C, and -40 °C. When the temperature decreases from 20 °C to 0 °C, the compressive strength of the specimens decreases, while the elastic modulus and peak strain increase. As the temperature continues to decrease, the compressive strength of the specimens increases, the elastic modulus continues to grow, and the peak strain decreases. The rising segments of the curves can be fitted using a cubic polynomial, and as the temperature decreases further, the parameters of the fitting curve gradually decrease. For concrete, being the most widely used material in the construction field, understanding its performance in low-temperature environments has become a significant research topic in the field of materials engineering and construction.

Formation of extraterrestrial peptides and their derivatives.

The formation of protein precursors, due to the condensation of atomic carbon under the low-temperature conditions of the molecular phases of the interstellar medium, opens alternative pathways for the origin of life. We perform peptide synthesis under conditions prevailing in space and provide a comprehensive analytic characterization of its products. The application of 13C allowed us to confirm the suggested pathway of peptide formation that proceeds due to the polymerization of aminoketene molecules that are formed in the C + CO + NH3 reaction. Here, we address the question of how the efficiency of peptide production is modified by the presence of water molecules. We demonstrate that although water slightly reduces the efficiency of polymerization of aminoketene, it does not prevent the formation of peptides.

Polystyrene nanoplastics in soil impair drought priming-induced low temperature tolerance in wheat

Drought priming is known to enhance plant low temperature tolerance, whereas polystyrene nanoplastic contamination exerts detrimental effects on plant growth. This study investigates the less-explored influence of nanoplastic contamination on cold stress tolerance in drought-primed plants. We compared the photosynthetic carbon assimilation, carbohydrate metabolism, reactive oxygen species metabolism, and grain yield between the non-primed and drought-primed wheat grown in both nanoplastic-contaminated and healthy soils. Our results reveal that the beneficial effects of drought priming on photosynthetic carbon assimilation and the efficiency of the “water-water” cycle were compromised in the presence of nanoplastics (nPS). Additionally, nPS exposure disturbed carbohydrate metabolism, which impeded source-to-sink transport of sugar and resulted in reduced grain yield in drought-primed plants under low temperature conditions. These findings unveil the suppression of nPS on drought-primed low-temperature tolerance (DPLT) in wheat plants, suggesting an intricate interplay between the induction of stress tolerance and responses to nPS contamination. The study raises awareness about a potential challenge for future crop production.