Supply Voltage Conditions Research Articles

Research on the Flicker Effect in Modern Light Sources Powered by an Electrical Network

Disruptions in power quality have a negative impact on many energy consumers. These include lighting, where interference manifests itself, among others, in the form of light flickering. The article presents phenomena accompanying the operation of modern light sources against the background of exemplary results of studies on the flicker of conventional light sources, such as incandescent or fluorescent lamps. The flickering effect of light generated in modern lamps can occur under stable voltage conditions in the supply network. The main subjects of the conducted research were solid-state light sources—light-emitting diode (LED) lamps, currently available on the lighting market. To assess the effects of these phenomena, it is necessary to use measures other than those traditionally used. The method used allows for the measurement of flicker resulting from both power supply disturbances and the properties of modern light sources. Using the developed measurement system, it is possible to record temporal changes in flicker coefficients resulting from, for example, changing supply voltage conditions. Due to the possibility of flickering light from sources offered by different manufacturers, as shown by research, it is advisable to carry out measurements at the place of use of the lighting.

Influence of a new controlled voltage regulator on the current and voltage non-sinusoidality of a power supply system

This work evaluates the influence of a new controlled voltage regulator on the current and voltage non-sinusoidality in different sections of a power supply system during smooth (discrete) voltage regulation on the high-voltage side of a shop transformer. The MatLab software application was used to develop a block-modular model for a transformer substation with the proposed controlled voltage regulator and measurement modules. The developed model was used to investigate the current and voltage non-sinusoidality in different parts of a power supply system when stabilizing the voltage at the consumer end at a given level. The study was carried out using a shop transformer with a capacity of 1 MV∙A and a voltage of 6/0.4 kV under an active-inductive character of the load with the load current phase angle of φ=45 deg. The obtained results confirm that, due to the extended functional capabilities of the proposed technical solution, the voltage at consumers is maintained at a given level under high technical and economic performance. When the network voltage is reduced by 5% and the activeinductive load current is increased by 35%, the proposed device was shown to create voltage non-sinusoidality. The voltage non-sinusoidality value does not exceed the permissible domestic and international norms. In addition, the proposed device is capable of maintaining the voltage at the consumer end at a given level. The obtained integral characteristic of voltage stabilization shows that the application of the proposed technical solution instead of the existing mechanical voltage regulator of the “switching without excitation” type allows the nominal voltage at the busbar of the switchgear to be retained. Further research will investigate voltage stabilization at consumers with simultaneous compensation of reactive power for complex improvement of technical and economic indicators of power supply systems under the conditions of unstable supply voltage and load current.

Effect of Voltage Supply Unbalance on Vibration of Three-Phase Induction Motor

Abstract The three-phase induction motor is the most popular electric motor used in industry. It has a simple and robust construction as well as a higher power density. It is a self-starting motor, therefore easier to start as compared to other types of electric motor. As the other benefit, a three-phase induction motor requires fewer maintenance measures. In order to maintain proper and continued operation, many parameters of a three-phase induction motor are constantly monitored. Among them is motor vibration. This is an important operation parameter frequently used to determine repair and maintenance needs to be taken on the motor. The vibration of a three-phase induction motor might be caused by mechanical as well as electrical problems. In this paper, the effect of magnitude unbalance of a three-phase voltage supply on the vibration of a three-phase induction motor is carefully investigated. To achieve this objective, two different laboratory experiments have been conducted. The first one is a three-phase induction motor supplied from a balance three-phase voltage supply. The second one is a three-phase induction motor supplied from an unbalance three-phase voltage supply. The unbalanced three-phase voltage supply condition is achieved by making the magnitude of one phase-voltage is 3%, 4%, and 5% lower than the magnitude of the other two phase-voltages. The vibration measurement is then taken in three different directions of the motor non-drive end (MNDE), i.e., horizontal (MNDEH), vertical (MNDEV), and axial (MNDEA). The experiment data show higher vibration in all directions, MNDEH, MNDEV, and MNDEA, as a load of the three-phase induction motor increases. Further, experiment data also show that higher vibration in all directions, MNDEH, MNDEV and MNDEA, is produced when unbalanced in magnitude voltage supply is higher

The Impact of Gamma Irradiation on 4H-SiC Bipolar Junction Inverters under Various Biasing Conditions

In this study, we introduce the impact of gamma irradiation on 4H-SiC based transistor-transistor logic (TTL) inverters. These monolithic bipolar inverters have been successfully demonstrated in a broad spectrum of temperature and supply voltage conditions. In this iteration of experiments, attempts made to the processing to increase beta values. The gamma radiation tests from a 60Co source were conducted under various operation conditions and measured in-situ under different biasing conditions. The Silicon Carbide Integrated circuits ( SiC ICs) show excellent tolerance properties to gamma radiation up to doses of nearly 1 MRad. Comparable Si BJT-based TTL inverters show considerable degradation already at one order of magnitude lower doses, clearly demonstrating the superior radiation hardness of 4H-SiC ICs.

Data-dependent half-select free GSRAM cell with word line write-assist and built-in read buffer schemes for use in PUFs-based IoT devices

In this study, a static-RAM cell using the Gnr-GDI method is proposed as a weak-type physical unclonable function (PUF) circuit to generate a unique and stable binary output for secure IoT devices. Regarding the memory level, a suitable combination of dynamic body bias, stacked networks, and multi-Vth techniques has been used in the architecture of asymmetric cell-structure inverters as a latch section to reduce power consumption and improve hardware efficiency. In addition, the logic styles of virtual ground and power gating based on word and BL data lines and a tri-state buffer structure have been used to extend the write VTC and improve read stability, respectively. From the perspective of PUF performance, the body of the latch section can form skewed VTCs based on the setting of critical parameters in GnrFET technology to achieve an efficient PUF circuit design.At the memory performance level, the Monte Carlo (MC) method-based results confirm the reasonable performance of the proposed structure in terms of static noise margin (SNM) and hardware efficiency, such as 53 % delay and 72 % energy-delay product (EDP) parameters, compared with the 6 T SRAM structure in a similar 16 nm GnrFET technology. In addition, in terms of the performance as a PUF circuit, the simulation results demonstrate the superiority of the proposed cell in terms of energy consumption, BER, response time, uniqueness, and stability under non-technological variation conditions of temperature and supply voltage. The outstanding performance results of the figure of merits (FoMs), CEQM, and UR2, which are composed of variability, energy, reliability, and layout-level factors, indicate the suitability of the proposed memory architecture for use in both the memory and PUF modes.Furthermore, to investigate the application level, memory structure has been used to store fingerprint images as PUF data using a hardware algorithm. The results of the proposed comprehensive FoM, which is based on the simultaneous consideration of circuit level and quality parameters, indicate that the proposed memory scheme in a bit-interleaved architecture-compatible design can be introduced as a high-performance candidate for generating and storing unique binary data in PUF-based IoT platforms.

Influence of the Supply Voltage Variation on the Conducted Emission in the Frequency Range up to 150 kHz Injected into the Power Grid by CFL and LED Lamps—Case Study

In normal operating conditions, the mains voltage level provided by low-voltage distribution networks follows time-varying patterns within permissible limits. The statistical characterisation of disturbances inserted into the power grid by nonlinear electrical devices is useful since operators are able to establish power quality limits and assess the residual capacity of networks for new smart installations, which may include a multitude of power electronic devices. Existing standards related to emission tests recommend using a power supply source in the measurement circuit with a nominal voltage parameter. However, the range of permissible variations of relevant supply voltage parameters may have an impact on conducted emissions. It can also be considered that the symptoms of supply voltage variations may manifest themselves differently depending on the equipment’s architecture and also the range of frequency observation with reference to harmonics and supraharmonics. The purpose of this study is to measure and analyze non-intentional conducted emissions injected into the power grid by lighting devices, methodically, by numbers of studies under different supply voltage conditions within two frequency bands. The emission is evaluated separately in two ranges: up to 2 kHz and 9-150 kHz. Obtained results show that the level of conducted emission introduced into the low voltage network by modern lighting sources like fluorescent and LED lamps varies with the supply voltage level compared to the emission generated in the nominal voltage level condition. Additionally, in the case of a spectrum of higher frequencies, some trends of shifting of the characteristic frequency bands are recorded. The potential of the obtained results is to complement the knowledge of the emission of modern lighting sources, which can be further used for digital models of these devices and to estimate the impact on the grid under real working conditions.

Hafnia-based oxide enhanced Ga2O3-based photodetectors via band engineering with ultralarge responsivity

β-Ga2O3 photodetectors achieve ultrahigh responsivity under low supply voltage and ultralow light intensity conditions via band engineering with polar Hf0.5Zr0.5O2 as an insert layer.

Study on the modes transformation and emission characteristics of Ionic Liquid Electrospray Thrusters

Ionic Liquid Electrospray Thrusters (ILETs) exhibit distinct emission characteristics when operating in different emission mode under different conditions, which can significantly impact their performance. Therefore, to optimize the performance of ILETs and make them suitable for a wide range of space missions, it is necessary to investigate the emission mode characteristics of ILETs. In this study, the ionic liquid 1-Ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (EMI-Im) was used to conduct experiments at varying supply voltage and flow rate conditions. The emitted current was measured and the liquid surface was imaged using a high-speed camera. The emission mode was estimated using algebraic calculations. Experimental results revealed that ILETs operate in the Ion-droplet Mixed mode at low flow rates, while the emission mode transforms into the Droplet mode as the flow rate increases. Similarly, as the supply voltage increases, the emission mode transforms from the Droplet mode to the Ion-droplet Mixed mode. The liquid surface height decreased with the supply voltage increase in each mode, and it increased with the flow rate in the Droplet mode. Notably, the liquid surface height in the Ion-droplet Mixed mode was similar to that in the Droplet mode at the lowest flow rate. Furthermore, the ion ratio significantly affected the thrust and specific impulse of ILETs.

Standard-Cell-Based Comparators for Ultra-Low Voltage Applications: Analysis and Comparisons

This work is focused on the performance of three different standard-cell-based comparator topologies, considering ultra-low-voltage (ULV) operation. The main application scenarios in which standard-cell-based comparators can be exploited are considered, and a set of figures of merit (FoM) to allow an in-depth comparison among the different topologies is introduced. Then, a set of simulation testbenches are defined in order to simulate and compare the considered topologies implemented in both a 130 nm technology and a 28 nm FDSOI CMOS process. Propagation delay, power consumption and power–delay product are evaluated for different values of the input common mode voltage, as a function of input differential amplitude, and in different supply voltage and temperature conditions. Monte Carlo simulations to evaluate the input offset voltage under mismatch variations are also provided. Simulation results show that the performances of the different comparator topologies are strongly dependent on the input common mode voltage, and that the best values for all the performance figures of merit are achieved by the comparator based on three-input NAND gates, with the only limitation being its non-rail-to-rail input common mode range (ICMR). The performances of the considered comparator topologies have also been simulated for different values of the supply voltage, ranging from 0.3 V to 1.2 V, showing that, even if standard-cell-based comparators can be operated at higher supply voltages by scaling their performances accordingly, the best values of the FoMs are achieved for VDD = 0.3 V.

Stator Inter-Turn Short-Circuits Fault Diagnostics in Three-Phase Line-Start Permanent Magnet Synchronous Motors Fed by Unbalanced Voltages

This paper addresses the diagnostics of stator faults in three-phase line-start permanent magnet synchronous motors. More traditional fault diagnostic methodologies are unable to properly diagnose stator inter-turn short-circuit faults in three-phase motors under unbalanced supply voltage conditions, since both conditions impact the fault indicators used for inter-turn short-circuit fault diagnostics in a similar way. In this paper, the relation between the symmetrical components of the three-phase quantities and the harmonic components of the Extended Park’s Vector Approach (EPVA) is established. It is proved that the negative component and the EPVA harmonic component at a frequency twice the supply frequency are directly related to the fault occurrence. It is also proved that the healthy motor negative impedance is constant and not load-dependent. Based on this, the negative impedance/admittance is indirectly analyzed, through the combined use of the Extended Park´s Vector Approach of both voltage and current, and is explored for the fault diagnostics. Experimental results, obtained for different load torques, unbalanced supply voltage values, and fault severity levels, show that inter-turn short-circuit fault diagnostics can be achieved even under unbalanced supply voltage conditions based on the analysis of the motor admittance, at a frequency twice the supply frequency, that is the negative sequence admittance.

Online Diagnosis and Discrimination of Stator Faults in Six-Phase Induction Motors Based on Voltage Symmetrical Components

In recent years, multiphase machines have been presented as a good alternative to the classical three-phase machines, mainly due to their ability to operate smoothly under fault conditions. Due to multiple stator phase arrangements, existing fault diagnostic (FD) methods are not sufficiently universal and cannot be applied to the multiple configurations of multiphase machines. In this regard, the current research proposes a universal and effective online diagnostics technique based on the computation and monitoring of a relevant severity factor, which is defined as the ratio of the zero, negative and positive voltage symmetrical components. The Short Time Least Square Prony’s (STLSP) approach is used to implement this method online in LabVIEW environment. In addition to the wide applicability of the method, the obviation of any motor parameter estimation and limited requirements regarding variables measurements make the proposed approach extremely advantageous for motors with high number of phases. This article addresses at stator faults in symmetrical six-phase induction machines (6PIM). The proposed method’s experimental results on six-phase motor drive platforms demonstrate the excellent generalization capability of the proposed method, as well as high accuracy and robustness, along with the ability to accurately distinguish between the occurrence of Inter-Turn Short Circuit (ITSC) faults and the presence of Unbalance Supply Voltage (USV) conditions. A 6PIM is put through its paces in both healthy and faulty conditions. The obtained results demonstrate the effectiveness of the proposed method for diagnosing the occurrence of ITSC faults and USV operating conditions with high reliability, fastness and high precision.

Modeling of Symmetrical Six-Phase Induction Machines Under Stator Faults

This paper addresses the occurrence of stator faults in six-phase induction machines, with a symmetrical winding, operating under both balanced and unbalanced supply voltage conditions. A dynamic model of the motor was developed in Matlab/Simulink environment, taking into consideration the occurrence of inter-turn short circuit faults. To validate the proposed approach, simulation results, covering the full range of operation and different fault severity levels, are compared with the motor experimental performance. The voltages and currents obtained from the simulation present a good agreement with the corresponding experimental results, demonstrating the accuracy of the proposed model

Model Predictive Control of Transformerless Series Custom Power Device for Voltage Quality Improvement

A single-phase series custom power device (Se-CPD), based on model predictive control (MPC), is presented in this paper to compensate for erratic supply voltage conditions such as voltage sag, swell, and harmonics. The control strategy for Se-CPD encapsulates the generation of reference voltage and optimal switching signals for the voltage source inverter (VSI) of the Se-CPD. The reference voltage extraction from the distorted point of common coupling (PCC) voltage is synthesized using a second-order generalized integrator (SOGI) without any phase delay, unlike the case that uses a low-pass filter (LPF). An MPC realizes the generation of optimal switching signals for Se-CPD with its intuitive and straightforward implementation, without any modulation stage, and considers the converter’s switching characteristics in the MPC algorithm itself. The simulation results, using MATLAB/Simulink and the real-time simulation results using the OPAL-RT OP4510 real-time simulator, are presented to validate the SOGI-MPC’s effectiveness for voltage quality improvement.

RPCNNet: A Deep Learning Approach to Sense Minor Stator Winding Interturn Fault Severity in Induction Motor Under Variable Load Condition

In this article, a deep learning-based automated framework has been proposed to sense minor stator winding interturn (MSIT) fault in an induction motor (IM) without having load level information. For this purpose, an experimental setup has been configured in laboratory through which three phase current signal of a three-phase squirrel cage IM has been recorded at different MSIT fault, different loading level and external voltage unbalance condition. In this proposed framework, three phase stator current profiles firstly are converted to 1-D Park’s vector modulus (PVM) signal using Park’s transformation and extended Park’s vector approach (EPVA). Thereafter, PVM of three phase stator currents have been encoded into RGB image using recurrence plot (RP) technique and have been fed to a customized convolutional neural network module (RPCNNet) for detection of MSIT fault severity. The recognition performance of the RPCNNet is also compared with four benchmark convolutional neural network (CNN) models namely “VGG16,” “AlexNet,” “ResNet50,” and “DenseNet201,” respectively. From the result, it is observed that RPCNNet has shown comparable performance and offers significantly reduced computational cost compared to the benchmark CNN models. Proposed framework has also outperformed the existing approaches by a significant margin and shown promising result under both noiseless and noisy environment. The proposed framework is also capable of differentiating MSIT fault condition from unbalanced supply voltage condition. Hence, proposed framework is very much suitable for practical application.

Impact of Inductor Placement on DC Bus Capacitor of Adjustable Speed Drives under Non-Ideal Supply Voltage Conditions

Diode bridge front-end Adjustable Speed Drives (ASDs) generally have an inductor either in the DC side (DC choke) or in the AC side (AC choke). Since both the types of ASDs are commercially widely used, a comparison of their behavior under normal and abnormal grid conditions is of interest. It is identified in this work that there exists a difference in the ripple current through the DC bus capacitor between the two variants. Further, the difference in the ripple current varies depending on the type of the disturbance and its level. As an outcome of the study, it is identified that the stress levels arising in the DC choke variant on the DC bus capacitor are lesser compared to the corresponding AC choke variant under balanced, unbalanced, and distorted grid voltage conditions, for the same value of the equivalent inductance in the AC and DC side. In order to match the stress levels arising in the DC bus capacitor between the ASDs with DC and AC choke, it is found that a 50% higher value of inductance is required in an AC choke variant. The effects are analyzed by simulations and validated using an experimental setup.

Development of a method for determining the rational installation location of technical means of symmetry in an electrical complex with the presence of an electric motor load

The work is devoted to the development of a methodological approach to correcting the level of supply voltage in the electrical network by developing an algorithmized method for determining the rational installation location of technical means of symmetry in an electrical complex with the presence of an electric motor load. The developed method makes it possible to implement processes aimed at ensuring the effective functioning of the electrical complex with the presence of an electric motor load in conditions of low-quality supply voltage. The proposed method, based on software, provides design procedures for calculating various options for symmetry and choosing the most economically feasible. Attention is focused on the main criteria for evaluating decisions made when designing the location of technical means of symmetry in the electrical complex. The architecture, the main functional features of the application program as a tool for implementing the calculation method are considered. The program ensures the implementation of electrical calculations in the design, modernization and operation of electrical networks. It provides for the construction of schematic diagrams of sections of electrical complexes with installed means of symmetry. The results of experimental studies demonstrating the effectiveness of the developed method in solving problems of voltage symmetry in the supply electrical network are presented. It is obvious that the developed approach, based on the automatic selection of the locations of the means of symmetry depending on the operating conditions of the electric motor load, makes it possible to automate the design procedures for voltage normalization in the electrical network. Provides minimization of voltage asymmetry in the supply electrical network, contributes to improving the operational reliability of low-voltage asynchronous electric motors. The obtained research results and prospects for the application of the developed approach are discussed, both for solving complex design problems and for the economic justification of local design solutions. A detailed analysis and formalization of the results of the study with relevant conclusions were carried out.

Optimal Design of an Artificial Intelligence Controller for Solar-Battery Integrated UPQC in Three Phase Distribution Networks

In order to minimize losses in the distribution network, integrating non-conventional energy sources such as wind, tidal, solar, and so on, into the grid has been proposed in many papers as a viable solution. Using electronic power equipment to control nonlinear loads impacts the quality of power. The unified power quality conditioner (UPQC) is a FACTS device with back-to-back converters that are coupled together with a DC-link capacitor. Conventional training algorithms used by ANNs, such as the Back Propagation and Levenberg–Marquardt algorithms, can become trapped in local optima, which motivates the use of ANNs trained by evolutionary algorithms. This work presents a hybrid controller, based on the soccer league algorithm, and trained by an artificial neural network controller (S-ANNC), for use in the shunt active power filter. This work also presents a fuzzy logic controller for use in the series active power filter of the UPQC that is associated with the solar photovoltaic system and battery storage system. The synchronization of phases is created using a self-tuning filter (STF), in association with the unit vector generation method (UVGM), for the superior performance of UPQC during unbalanced/distorted supply voltage conditions; therefore, the necessity of the phase-locked-loop, low-pass filters, and high-pass filters are totally eliminated. The STF is used for separating harmonic and fundamental components, in addition to generating the synchronization phases of series and shunt filters. The prime objective of the suggested S-ANNC is to minimize mean square error in order to achieve a fast action that will retain the DC-link voltage’s constant value during load/irradiation variations, suppress current harmonics and power–factor enhancement, mitigate sagging/swelling/disturbances in the supply voltage, and provide appropriate compensation for unbalanced supply voltages. The performance analysis of S-ANNC, using five test cases for several combinations of loads/supply voltages, demonstrates the supremacy of the suggested S-ANNC. Comparative analysis was carried out using the GA, PSO, and GWO training methods, in addition to other methods that exist in the literature. The S-ANNC showed an extra-ordinary performance in terms of diminishing total harmonic distortion (THD); thus PF was improved and voltage distortions were reduced.

Mitigation of power quality problems using voltage-controlled based modified DSTATCOM

ABSTRACT This paper proposes a modified distribution static compensator (DSTATCOM) with the voltage controller. The modified DSTATCOM is incorporated in a three-phase four-wire distribution network. The design criteria of the modified DSTATCOM parameters is introduced. The Hysteresis Voltage Controller (HVC) is used to drive the Voltage Source Converter (VSC) and its reference voltage signal is generated based on the Instantaneous Symmetrical Components Theory (ISCT) to provide the proper compensation to stabilise the system voltage, improve the power factor and mitigate the harmonic distortion. Matlab/Simulink software is used to verify the performance of the modified DSTATCOM with the used controller under different load types and supply voltage conditions. The control algorithm ensures that the bus voltage is maintained at its rated value during different connected loads and supply conditions. Also, it compensates the non-linear and unbalanced supply currents and reducing the Total Harmonic Distortion (THD) of both current and voltage. The proposed modified DSTATCOM gives better results in comparison with the conventional DSTATCOM.

Analysis of the degree of influence of supply voltage asymmetry on the operational reliability of low-voltage asynchronous electric motors

THE PURPOSE. The relevance of research is that the comprehensive substantiation of issues aimed at ensuring the effective functioning of the electrical complex with the presence of an electric motor load in conditions of low-quality supply voltage. The aim of the work is to study the effect of the asymmetry of the supply voltage on the service life of an asynchronous motor with a short-circuited rotor. The main attention is paid to the dynamics of changes in the service life of low-voltage asynchronous electric motors of various series, depending on the level of voltage asymmetry. Asynchronous electric motors of the classic series (4A, AI) and the upgraded (5A, AI’) are identified as the object of research. As is known, the efficient and reliable operation of electric motors is characterized by the service life of the insulation of the windings. A qualitative assessment of the operational reliability of AM is determined by the accuracy of forecasting the real life of their service. That is why, it becomes obvious, the task of an adequate assessment of the operational reliability of low-voltage asynchronous electric motors operating under conditions of low-quality supply voltage directly depends on the complex of studies of such an external influencing factor as the asymmetry of the supply voltage. METHODS. The realization of the research objectives was carried out using the software package "SimPowerSystems" of the interactive programming environment Matlab/Simulink. RESULTS. The research was carried out on asynchronous motors with a short-circuited rotor: classic series (4A132S4, AIR160S8), upgraded series (5A132M6, AIR132S4) with PH = 7,5 kW, rated speed n = 1500 rpm. Modeling of the physical processes of the studied electric motors was carried out by changing the voltage asymmetry coefficient in the reverse sequence (K2U) from 0 to 5% in increments of 1%. Based on the obtained simulation results, diagrams of the change in the service life of AM from the magnitude of the influencing factor are constructed. The studies performed using computer modeling based on the "SimPowerSystems" software package of the Matlab/Simulink system made it possible to predict changes in the service life of AM, estimate the limits of permissible values of the voltage asymmetry coefficient in the reverse sequence, compare the studied electric motors by the level of resistance to an external influencing factor. CONCLUSION. A comprehensive solution to issues related to improving the operational reliability of low-voltage asynchronous electric motors is one of the priority areas, mainly aimed at ensuring the effective functioning of the electrical complex with an electric motor load. In the course of the study, a detailed assessment and analysis of the degree of influence of the asymmetry of the supply voltage on the operational reliability of low-voltage asynchronous electric motors was carried out. The results of the study were discussed, recommendations for the use of asynchronous electric motors in the presence of asymmetry of the supply voltage were formulated.

Single-Phase Universal Power Compensator with an Equal VAR Sharing Approach

In this manuscript, we propose a single-phase UPC (universal power compensator) system to extensively tackle power quality issues (voltage and current) with an equal VAR (volt-ampere reactive) sharing approach between the series and shunt APF (active power filter) of a UPC system. The equal VAR sharing feature facilitates the series and shunt APF inverters to be of an equal rating. An SRF (synchronous reference frame)-based direct PA (power angle) calculation technique is implemented to realize equal VAR sharing between the APFs of the UPC. This PA estimation utilizes d and q axis current parameters derived for the reference signal generation of the shunt APF. An SRF-based method is highly useful for power estimations in distorted supply voltage conditions compared with other conventional methods, i.e., the PQ method. It comprises a reduced complexity and estimations with an easiness to retain two APF inverters of equal rating. A rigorous simulation analysis is performed with MATLAB/SIMULINK and a real-time digital simulator (OPAL-RT) for addressing different power quality-disturbing elements such as current harmonics, voltage harmonics, voltage sag/swell and load VAR demand with the proposed method.