Concentration Range Research Articles

A dual-signal ECL-RET immunosensor based on VC-g-C3N4 and Ru-Zr-MOF for the detection of β2-MG

This work proposes a novel dual-signal electrochemiluminescence (ECL) immunosensor based on energy resonance transfer (RET) for the detection of β2-Microglobulin (β2-MG). Introducing carbon vacancy into g-C3N4 (VC-g-C3N4) can lead to the narrowing of the band gap and the reduction of LUMO, thereby significantly enhancing the ECL efficiency of the material. Meanwhile, Zr-MOF can effectively load Ru(bpy)32+ (Ru-Zr-MOF), enabling its stable existence on the electrode. The ECL emission spectrum of VC-g-C3N4 overlaps well with the fluorescence excitation spectrum of Ru-Zr-MOF, indicating an effective ECL-RET effect between them. As the concentration of β2-MG increases, the intensity of anodic ECL signal gradually increases, while the intensity of cathodic ECL signal gradually decreases. The difference between the cathodic and anodic ECL signals has a good linear relationship within the concentration range from 0.2 pg/mL to 200 ng/mL, with a detection limit of 27.73 fg/mL. The constructed immunosensor can be used for practical analysis in human serum. The proposed sensor has great potential in clinical detection of β2-MG, providing new insights for biomolecular detection and disease diagnosis.

Design, Synthesis and In vitro Screening of Novel 2-Mercaptobenzothiazole- Clubbed Phenylacetamides as Potential Antibacterial Agents

Background: The frightening rise of bacterial resistance is occurring worldwide and endangering the efficacy of antibiotics. Hence, the development of novel and potent antibacterial is a need of the day. Objective: In this study, we designed and synthesized compounds C1-C11. These compounds are characterized by their FT-IR, NMR and MS spectral data and examined in vitro for their antibacterial activity. Methods: Compounds C1-C11 were synthesized by reacting 2-mercaptobenzothiazole with appropriate chloroacetamide in the presence of anhydrous potassium carbonate and dry acetone at room temperature. To assess the antibacterial activity, minimum inhibitory and minimum bactericidal concentrations were examined by broth microdilution method against the selected strains of both Gram-positive and Gramnegative bacteria. Time-kill kinetics study was also performed as per CLSI guidelines. Results: Compounds C6 and C7 displayed promising activity against Staphylococcus aureus ATCC 43300 with MICs of 9.43 and 7.73 μM, respectively. These two compounds also displayed promising antibacterial activity against S. aureus 5021 with MIC values of 7.53 and 9.68 μM, respectively. In MBC determination, these two compounds (tested in the concentration range of 7.53 to 262.3 μM) displayed bactericidal activity against methicillin resistant S. aureus ATCC 43300, S. aureus NCIM 5021 and S. aureus NCIM 5022. In time-kill kinetics study, compounds C6 and C7 also exhibited bactericidal activity against S. aureus NCIM 5021 and S. aureus ATCC 43300 after 12 h of exposure. In general, all tested compounds exhibited poor activity against Mycobacterium sp. NCIM 2984 and also against tested Gramnegative bacteria Klebsiella pneumoniae NCIM 2706, Escherichia coli NCIM 2065 and Pseudomonas aeruginosa NCIM 2036. Further, computed ADMET properties of C1-C11 showed a favourable pharmacokinetic profile with zero violation of Lipinski’s rule of five. Conclusion: The result showed that in phenylacetamides C6 and C7 presence of phenyl ring substituted with -CF3 group is responsible for their high antibacterial activity against S. aureus ATCC 43300 (MICs, 9.43 and 7.73 μM, respectively). These two compounds also exhibited bactericidal activity respectively against S. aureus NCIM 5021 in time kill kinetics study.

Experimental Approaches to Iron Determination in Potentiometric Sensors Using (2-2-(4-Dinitrophenyl) Hydrazono) Methylphenol

The study presents a PVC membrane-based potentiometric sensor for iron (III) detection, demonstrating impressive selectivity in Fe(III) ion-selective electrodes (ISE). The sensor achieves a detection limit of 4.0×10−7 M and a Nernstian response slope of 19.4 mV per decade change within a concentration range of 7.4×10−7 to 1×10−1 M. Operating efficiently within the pH range of 3.6–10, the sensor maintains its potential divergence-free utility for at least eight weeks and has a rapid response time of approximately twenty seconds. The sensor’s selectivity for Fe3+ ions makes it a robust tool for specific Fe(III) ion detection. The sensor’s reliability and longevity make it a valuable tool for continuous monitoring applications, providing accurate and timely information on the presence of iron ions in diverse settings.

Iron ion detection and life cycle assessment of cutting fluid based on photoluminescent nitrogen-doped carbon quantum dots

Cutting fluid (CF) ensures machining accuracy and improves tool life in machining, which is of great significance for its impurity content detection and life cycle evaluation. In this paper, citric acid and arginine were used as carbon and nitrogen sources, photoluminescent (PL) nitrogen-doped carbon quantum dots (N-CDs) with a particle size ranging from 8 to 14 nm and well dispersion in water-based CF were synthesized by a one-pot hydrothermal reaction method. The N-CDs have the best signal under 360 nm ultraviolet light excitation, which well avoids the autofluorescence of the CF. The N-CDs dispersion have good selectivity and linearity in the Fe3+ concentration range of 2 to 80 μM, and the detection limit is 1.2 μM. The N-CDs were used to detect the concentration of Fe3+ in CF with different working hours, and the results were consistent with the results of coupled plasma emission spectroscopy. This study provides an intelligent sensing platform for the highly sensitive and selective detection of Fe3+ in the CF environment, and provides a promising strategy for the evaluation of the CF lifetime.

Laser-induced graphene decorated with Ni[sbnd]Pt alloy nanoparticles for non-enzymatic electrochemical quantification of glucose

Enzyme-free electrochemical glucose (Glu) sensors, adopting electrochemically active catalysts, are of vital significance to effectively monitoring and analyzing the blood Glu level in diabetes diagnosis. Meanwhile, developing novel electrode substrates have been the hot research pot to meet the demand for constructing flexible sensors. In this work, porous laser-induced graphene (LIG) was prepared through a facile one-step laser-engraving technique on a polyimide thin film, and then used directly as the electrode. Furthermore, NiPt alloyed nanoparticles (NPs) were electrodeposited on the LIG electrode surface to gain the NiPt/LIG composite electrode, which was applied to construct the nonenzymatic electrochemical Glu sensor. The morphology, element and electrochemical performance of NiPt/LIG composite was characterized through various techniques. NiPt alloyed NPs were homogeneously distributed on the LIG scaffolds, which possess plenty of porous structure, high surface area and many active sites. The cooperative effect between the outstanding electrocatalytic capacity of NiPt alloyed NPs, the extraordinary electroconductibility of LIG and the numerous exposed active sites endow the NiPt/LIG sensor outstanding electrocatalytic performance for electrochemical oxidation of Glu. Under the most appropriate conditions, the obtained NiPt/LIG sensor was adopted to detect Glu, showing a broad detection concentration range of 0.5 μM to 2.1 mM and 2.1 mM to 5.6 mM, good sensitivities of 1.824 and 0.467 μA μM−1 cm−2, a low detection limit of 0.03 μM. The as-fabricated nonenzymatic Glu sensor also displays high selectivity, stability considering ageing effects under different environment conditions and prominent reproducibility. Additionally, this novel NiPt/LIG nonenzymatic Glu sensor was applied to quantify Glu successfully in blood serum and food samples and the results were in good agreement with that by UV–vis spectrophotometer, demonstrating high precision and accuracy as well as excellent recovery, showing good application prospects in Glu monitoring. This research confirmed the potential of exploiting NiPt/LIG as a highly sensitive Glu nonenzymatic electrochemical sensor and provided a practicable and suitable approach for construction of novel electrochemical sensors.

A Low-cost Two-in-one Fluorescence/ Colorimetry Ammonium Detector: Design and Application

In this study, a compact and low-cost ammonium detector integrated spectrophotometric and fluorescence detection was designed based on the reaction of ammonium and o-phthalaldehyde in the presence of sodium sulfite solution to form substances with both photometric properties and fluorescence. This two-in-one detector detects ammonium in spectrophotometric mode at high concentrations and in fluorescence mode at low concentrations. The detector with a total size of 5×5×5 cm2 and integrates the detector skeleton box, light source, attenuator, filter, photoelectric sensor, data acquisition card, constant current source circuit, and LabVIEW upper computer acquisition program. Also, the detector was applied to the determination of water samples with a wide range of ammonium concentrations, showing good performance. The detector has the advantages of low cost, miniaturization, easy operation, and wide detection concentration range. This two-in-one detector has good potential for ammonium detection in the field, especially where ammonium concentration varies widely.

Green voltammetric method for determination of diclofenac sodium in environmental and biological samples using aluminium tungstate nanoparticles modified carbon paste electrode

ABSTRACT Based upon aluminium tungstate (Al2(WO4)3 NPs), a new modified sensor was created in order to monitor diclofenac sodium (DCF) electrochemically in environmental samples. The electrode composition, electrolyte effect, selectivity, scan rate, and pH parameters that affect the assay’s performance were optimised and the pH study revealed that pH 3.6 was found to be suitable to improve the electrochemical behaviour of diclofenac. The electrochemical characteristics of the built-in electrode were assessed using cyclic voltammetry technique (CV).The electrode composition, electrolyte effect, selectivity, scan rate, and pH parameters were optimised. The limit of detection was found to be 0.076 µM and the limit of quantification (LOQ) value was 0.25 µM for the concentration range (0.2–25 µM) of DCF. It has demonstrated good selectivity for (DCF) in presence of the interfering species and its electrochemical sensing’s repeatability, reproducibility and stability were evaluated and found typical. Some environmental samples like tap water, waste water, Nile-river water and biological ones like urine and plasma, have been effectively applied using the proposed electrochemical sensor. Green chemistry metrics, viz. Analytical GREEnness Preparation (AGREEprep), Analytical Eco-Scale Assessments (ESA) and The AMVI for the proposed method were calculated and have assured that the method has limited negative impact on both human health and the environment.

Recovery of Propionic Acid from Aqueous Phase using Alamine 336 in 1 - Octanol by Reactive Extraction

The by-products of carboxylic acids are useful in chemical industry, pharmaceutical industry, preservations, drug delivery towards a more economical energy efficient technology. Physical and chemical equilibria results are presented as equilibrium distribution, distribution co -efficient, extraction efficiency, loading ratio and volume percentage by varying concentrations. The distribution of propionic acid between aqueous phase and organic phase reaches equilibrium over a concentration range of 0.009 kmol/m3 – 0.055 kmol/m3 . The optimum TOA concentration is found to be 40% at which KD value for 1 - octanol is 16.7. The modified separation increases with decrease in TOA & acid concentration and alamine loading with acid Z decreases with increase in alamine concentration in 1 – octanol. Optimum extraction efficiency is 43.82% for a conc. of 40% TOA at 0.2 kmol/m3.

Eco-friendly optical sensor for precise detection of gold ions in diverse matrices through the integration of β-2-hydroxybenzyl-3-methoxy-2-hydroxyazastyrene in a PVC membrane.

An environmentally conscious methodology is investigated for the precise and discerning identification of trace concentrations of gold ions in diverse matrices. A novel optical sensor membrane is proposed for the determination of Au3+ ions, utilizing the immobilization of β-2-hydroxybenzyl-3-methoxy-2-hydroxyazastyrene (HMHS) entrapped in polyvinyl chloride (PVC). The sensor incorporates sodium tetraphenylborate (Na-TPB) as the ionic additive and dibutyl phthalate (DBP) as a plasticizer. Under optimal conditions, the suggested sensor exhibits a linear calibration response to Au3+ ions within a concentration range of 5.0 to 165 ng mL-1. Detection and quantification limits are specified as 1.5 and 4.8 ng mL-1, respectively, with a rapid response time of 5.0 min. Upon presentation, this optical sensor not only affirms high reproducibility, stability, and an extended operational lifespan but also showcases exceptional selectivity for Au3+ ions. Notably, no discernible interference is observed when assessing the potential influence of other cations and anions on Au3+ ion detection. The adaptability of this optical sensor is validated through its successful application in determining Au3+ ion concentrations across various sample types, including water, environmental, cosmetics, and soil matrices.

Nanoarchitectonics of an acetogenin-enriched nanosystem mediated by an aqueous extract of Annona cherimola Mill with anti-inflammatory and proapoptotic activity against HepG2 cell line

For the first time, this study shows the nanoarchitectonic process to obtain an acetogenin-enriched nanosystem (AuNPs-Ac) using an aqueous extract from Annona cherimola Mill (ACM) composed of gold nanoparticles embedded in an organic matrix that acts as stabilizing agent and presents anti-inflammatory activity and cytotoxical effect against HepG2 cell line, promoting apoptosis. The synthesis of AuNPs-Ac was confirmed by x-ray diffraction analysis, showing metallic gold as the only phase, and the scanning transmission microscope showed an organic cap covering the AuNPs-Ac. Fourier-transformed infrared suggests that the organic cap comprises a combination of different annonaceous acetogenins, alkaloids, and phenols by the presence of bands corresponding to aromatic rings and hydroxyl groups. High-Performance Liquid Chromatography has demonstrated the presence of annonacin, a potent acetogenin, in the extract of ACM. An in vitro anti-inflammatory activity of the extract of ACM and the AuNPs-Ac was performed using the albumin denaturation method, showing a nonlinear response, which is better than sodium diclofenac salt in a wide range of concentrations that goes from 200 to 400 μg ml−1 with both samples. The viability assay was studied using trypan blue, treating IMR90 and HepG2 at different concentrations of AuNPs-Ac. The results defined a median lethal dose of 800 μg ml−1 against HepG2 through apoptosis according to the ratio of caspase-cleaved 9/alpha-tubulin evaluated. It was also demonstrated that the nanosystem presents a higher cytotoxic effect on the HepG2 cell line than in IMR90, suggesting a targeted mechanism. In addition, the nanosystem performs better than using only the extract of ACM in the anti-inflammatory or antiproliferative test, attributed to their higher surface area.

Standard operating procedure for the analysis of major ions in hydrothermal fluids by ion chromatography

This standard operating procedure (SOP) describes an ion chromatography (IC) procedure for the major cations and anions in hydrothermal fluids. Hydrothermal fluids are aqueous solutions with a wide range of temperature, salinity, pH and ion species that can be used by microbial metabolism as electron donors and electron acceptors. Due to the high variability of the environmental physical-chemical parameters in these samples, we have developed this protocol taking into account the special features of the matrices analyzed. An Eco IC Metrohm system equipped with a conductivity detector was used. Calibration curves are linear in the 0.1 to 10 mg/L concentration range for cations Ca2+, Na+, K+, Mg2+, NH4 + and anions Cl-, Br-, NO3 -, NO2 -, SO4 2- , HPO4 2-.

Highly Selective Ratiometric Sensors for Pb2+ Based on Luminescent Zn(II)-Coordination Polymers with Thiophenedicarboxylate. Crystal Structures and Spectroscopic Studies.

The development of luminescent coordination polymers for the selective sensing of Pb2+ in water constitutes an active area of research that impacts analytical, environmental, and inorganic chemistry. Herein, two novel water-stable 2D Zn-coordination polymers {[Zn2(H2O)2(tdc)2(bpy)]·(H2O)}n 1 and [Zn(tdc)(tmb)]n 2 (tdc = thiophenedicarboxylate; bpy = 4,4'-bipyridine and tmb = 4,4'-trimethylenebipyridine) were synthesized, structurally determined by single crystal X-ray diffraction, and studied in-depth as luminescent sensors for a series of cations (Ca2+, Mg2+, Mn2+, Fe2+, Co2+, Ni2+, Cu2+, Zn2+ Cd2+, Hg2+ and Pb2+) in 20% aqueous ethanol. These Zn-polymers possess photostability in 20% aqueous ethanol with a strong emission at 410 upon excitation at 330nm and quantum yields of around Φ = 0.09. Under these conditions, Pb+2 can be efficiently sensed with polymer 2 through a fluorescent ratiometric response with selectivity over common interfering metal ions such as Cu2+, Cd2+ and Hg2+ in the micromolar concentration range (detection limit = 1.78 ± 10μM). Such selectivity/affinity of Pb2+ over Hg2+ for luminescent chemosensors is still rare. On the basis of spectroscopic tools (1H NMR, far ATR-IR, PXRD), the X-ray crystal structure of 2, and Scanning Electron Microscopy with Energy-Dispersive X-ray Spectroscopic analysis, the ratiometric fluorescent response is proposed via an efficient metal-ion exchange driven through interactions between thiophenedicarboxylate rings and Pb2+ ions. The use of flexible luminescent Zn-coordination polymers as sensors for selective and direct detection of Pb2+ in aqueous media has been unexplored until now.

Consumption of pollen contaminated with field-realistic concentrations of fungicide causes sublethal effects in Bombus impatiens (Hymenoptera: Apidae) microcolonies.

Bumble bees are declining across the globe. The causes of this decline have been attributed to a variety of stressors, including pesticides. Fungicides are a type of pesticide that has been understudied in the context of bumble bee health. As a result, fungicides are often applied to flowering plants without consideration of pollinator exposure. Recent work demonstrates that fungicides have sublethal effects in bumble bees, but little is known about how much fungicide it takes to cause these sublethal effects. To address this gap in the literature, we fed microcolonies of the common eastern bumble bee (Bombus impatiensCressonHymenoptera: ApidaeHymenoptera: ApidaeHymenoptera: ApidaeHymenoptera: Apidae) pollen contaminated with a range of fungicide concentrations. We chose these concentrations based on the range of fungicide concentrations in pollen and nectar that were reported in the literature. Results revealed that later-stage pupae and newly emerged males are potentially sensitive to fungicide exposure, showing smaller size and reduced fat reserves at intermediate levels of contamination. Compared to the control, intermediated levels of fungicide-contaminated pollen led to increased pupal mortality and delayed male emergence. Contrary to expectations, higher fungicide levels did not exhibit a linear relationship with negative impacts, suggesting nuanced effects. Because body size and emergence timing are important aspects of bumble bee reproductive behavior, results have implications for mating success, potentially disrupting colony development.

First report of leaf spot disease caused by Neopestalotiopsis rosae on Lonicera caerulea L. in Heilongjiang Province, China.

Recently, interest in cultivating blue honeysuckle (Lonicera caerulea L.) for horticulture and medicinal uses has grown (Sharma and Lee 2021). Between September 2022 and September 2023, a leaf spot disease (Fig. S1) was observed on approximately 20% of 'Lanjingling' blue honeysuckles grown in a 0.18 ha field in Qiqihar city (123.43°E, 47.92°N), Heilongjiang Province, China. Infected plants displayed black leaf spots that expanded to cover the entire leaf. Small, 3 to 4 mm segments of infected tissue were surface sterilized with 75% ethanol for 30 s and 5% sodium hypochlorite (NaOCl) for 3 min, rinsed three times with sterile distilled water, dried on paper towels, and plated in 9 cm Petri dishes containing potato dextrose agar (PDA) (Ma et al. 2023). To induce sporulation, nine purified cultures (Fig. S2) with similar culture characteristics were finally obtained from ten infected plants and they displayed a conidia morphology consistent with Neopestalotiopsis spp., no other fungi were isolated, and the isolation frequency was 90%. Conidiomata (Fig. S3) were brown to black and distributed in concentric rings with an average size of 261.98 (60.30-451.80) μm (n = 50). The conidia (Fig. S3) were fusoid and had four septa, straight to slightly curved, with an average size of 23.48 (13.50-30.30) × 5.42 (4.50-9.30) μm(n = 50), while basal and apical cells were hyaline and the three middle cells were brown with darker septa. PCR amplification was performed with ITS1/ITS4 (White et al. 1990), EFl-728F/EF1-986R (Carbone and Kohn 1999), and Btub2Fd/Btub4Rd (Glass and Donaldson 1995) primers from the genomic DNA of the LD-330. Sequences of ITS (PP033584), TEF (PP048757), and TUB (PP048758) revealed 99 to 100% (499/500, 255/255, and 481/486) shared identity with Neopestalotiopsis rosae sequences (NR145243, KM199524, and KM199430) (Rebollar-Alviter et al. 2020). Therefore, based on morphological characteristics and molecular phylogeny, LD-330 was identified as N. rosae. Six two-year-old healthy plants of the 'Lanjingling' cultivar were selected for a pathogenicity test (Yan et al. 2023). The leaves were surface disinfected with 75% alcohol and then wiped with sterilized water three times. Three plants were inoculated with 10 ml of LD-330 conidial suspension (1 × 106 spores/ml) or with sterile water as an experimental control, respectively. All plants were in closed plastic bag, incubated in a greenhouse at 28 ℃ and 75% relative humidity (RH) under a 12-h light/dark cycle, and each experiment was performed three times (Rebollar-Alviter et al. 2020). Typical leaf spot symptoms were observed on inoculated leaves after 14 days (Fig. S4), whereas no symptoms were detected on water-treated leaves. The same pathogen was reisolated from infected leaves, displayed the same morphological and molecular traits, and was again identified as N. rosae, confirming Koch's postulate. Neopestalotiopsis rosae was previously reported on pecan (Gao et al. 2022), causing black leaf spot disease in China. To our knowledge, this is the first report of a blue honeysuckle leaf spot caused by N. rosae in China and specifically in the Heilongjiang province which has the largest blue honeysuckle cultivation area in the country. Future research should be directed toward developing comprehensive management measures.

Multicenter comparison of Etest, Vitek2 and BD Phoenix to broth microdilution for beta-lactam susceptibility testing of Streptococcus pneumonia.

To assess performance of Etest®, Vitek®2 and BD Phoenix™ to determine the susceptibility of Streptococcus pneumoniae strains to penicillin, ampicillin and cefotaxime. Sixty unique S. pneumoniae challenge strains were selected to cover a wide range of penicillin, ampicillin and cefotaxime minimal inhibitory concentrations (MICs). Strains were analyzed in four different Belgian laboratories. Etest® benzylpenicillin (BEN), ampicillin/amoxicillin (AMP) and cefotaxime (CTA) (bioMérieux), Vitek®2 AST-ST03 (bioMérieux) and BD Phoenix™ SMIC/ID-11 testing were each performed in two different labs. Results were compared to Sensititre® broth microdilution (BMD) (Thermo Fisher Scientific) results. MIC results were interpreted using EUCAST non-meningitis breakpoints (v 13.0). Essential agreement (EA) was ≥ 90% for all methods compared to BMD, except for Etest® BEN on Oxoid plate (58.3%), Etest® AMP (both on Oxoid (65.8%) and BD BBL plate (84.2%)). Categorical agreement (CA) for penicillin was only ≥ 90% for Vitek®2, for other methods CA ranged between 74 and 84%. CA for AMP was for all methods < 90% (range 75.8-88.3%) and CA for CTA was between 87 and 90% for all methods except for Etest on Oxoid plate (79.2%). Our study indicates that Vitek®2 and BD Phoenix™ are reliable for providing accurate pneumococcal susceptibility results for BEN, AMP and CTA. Using Etest BEN or AMP on Oxoid plate carries a risk of underestimating the MIC and should be interpreted with caution, especially when the obtained MIC is 1 or 2 doubling dilutions below the S or R clinical breakpoint.

Avapritinib Carries the Risk of Drug Interaction via Inhibition of UDP-Glucuronosyltransferase (UGT) 1A1.

Avapritinib is the only drug for adult patients with PDGFRA exon 18 mutated unresectable or metastatic Gastrointestinal Stromal Tumor (GIST). Although avapritinib has been approved by the FDA for three years, little is known about the risk of Drug-drug Interac-tions (DDIs) via UDP-glucuronyltransferases (UGTs) inhibition. The aim of the present study was to systematically evaluate the inhibitory effects of avapritinib against UGTs and to quantitatively estimate its potential DDIs risk in vivo. Recombinant human UGTs were employed to catalyze the glucuronidation of sub-strates in a range of concentrations of avapritinib. The kinetics analysis was performed to evaluate the inhibition types of avapritinib against UGTs. The quantitative prediction of DDIs was done using In vitro-in vivo Extrapolation (IVIVE). Avapritinib had a potent competitive inhibitory effect on UGT1A1. Quantitative predic-tion results showed that avapritinib administered at clinical doses might result in a 14.85% in-crease in the Area Under the Curve (AUC) of drugs primarily cleared by UGT1A1. Moreover, the Rgut value was calculated to be 18.44. Avapritinib has the potential to cause intestinal DDIs via the inhibition of UGT1A1. Additional attention should be paid when avapritinib is coadministered with UGT1A1 substrates.

Catch and release: controlling eastern yellowjacket Vespula maculifrons colonies using horizontal insecticide transfer.

Horizontal insecticide transfer is thought to play an important role in controlling a wide range of urban pests including ants, bed bugs, cockroaches and termites. Trap-treat-release is an effective experimental approach that has been used to successfully manage populations of invasive ants in field applications. Trap-treat-release is based on the principles of horizontal transfer. Individuals are captured, treated with the toxicant and released back into the environment. The treated individuals then return to the colony and transfer the toxicant to other members of the population resulting in secondary mortality. The goal of the current study was to evaluate the efficacy of the trap-treat-release technique for controlling field populations of the eastern yellowjacket, Vespula maculifrons. Laboratory experiments demonstrated that fipronil was highly toxic against V. maculifrons across a wide range of concentrations. Furthermore, fipronil was efficiently transferred from treated donors to untreated recipients and caused significant secondary mortality. A field experiment utilized trap-treat-release and demonstrated that fipronil was effectively transferred when foraging worker wasps are trapped, treated, released and allowed to return to their respective colonies. The trap-treat-release method may be an effective alternative to direct nest treatments and could help alleviate problems such as insecticide runoff, environmental contamination, and non-target effects. This method has the potential to provide effective management of social wasps. © 2024 The Author(s). Pest Management Science published by John Wiley & Sons Ltd on behalf of Society of Chemical Industry.

EDTA functionalized pine needle biochar (EDTA@BC); a valorized bio-material for removal of Ni(II) from aqueous solution.

The preparation of ethylenediaminetetraacetic acid (EDTA) functionalized pine needles biochar (EDTA@BC) as a low-cost active adsorbent and its effectiveness in removing Ni(II) from aqueous solution at various conditions is reported in this paper. First, alkali activation was selected to render the pine needle biochar with an excellent porous structure and increased concentration of hydroxyl groups to facilitate grafting. Subsequently, a simple method was utilized to graft EDTA onto the biochar. The prepared EDTA@BC was characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and energy dispersive x-ray spectrometry (EDX). Batch adsorption studies were conducted to assess the impact of various parameters such as solution pH, adsorbent dosage, adsorbate volume, and shaking time on the removal efficiency of Ni(II). At pH 6, 100 mg dosage, 4 mL of adsorbate volume, and 10 min of shaking time, the maximum removal efficiency of Ni(II) was observed to be 89%. EDTA@BC showed reasonable sorption performance still after the third cycle of regeneration. The effect of interfering ions such as Pb, Cr, Cu, and Hg was evaluated, resulting a decrease of 69%, 78%, 76%, and 68%, respectively, in its sorption capacity. The Langmuir model provided a better fit for Ni(II) in the concentration range of 0.1-2000 ppm under optimized conditions, with qmax of 46.69 ± 1.031 mg/g and KL of 0.001, compared with the Freundlich isotherm, which yielded n = 0.234 and χ2 = 2.7899, Temkin isotherm (R2 = 0.9520), and Redlich-Peterson isotherm (R2 = 0.9725). The removal of Ni(II) by EDTA@BC was found to be the pseudo-second-order kinetics. Thermodynamic studies indicated adsorption process to be endothermic and nonspontaneous. Hence, a sustainable valorized bio-material (EDTA@BC) is prepared having better sorption efficiency of Ni(II) from aqueous solution with possible wide applicability. RESEARCH HIGHLIGHTS: New EDTA functionalized indigenous pine needles biochar (EDTA@BC) was prepared. This low-cost active adsorbent found effective in removing Ni(II) from aqueous solution. FTIR, SEM, and EDX proved synthesis and uptake of Ni(II) from aqueous solution. Ni(II) removal, regeneration, interfering and adsorption studies were performed by UV-Vis spectroscopy.

Behavioral and electrophysiological study in Colossoma macropomum treated with different concentrations of Nepeta cataria oil in an immersion bath revealed a therapeutic window for anesthesia.

The purpose of this study was to characterize the activity of essential oils from Nepeta Cataria (EON) at concentrations of 125 L-1, 150 L-1, 175 L-1, and 200 L-1 on the behavior of loss of the posture reflex and recovery of the posture reflex and electrocardiographic activity and recording of the opercular beat of Colossoma macropomum during immersion bathing for a period of 5min, in order to obtain a window for safe use during anesthesia. The fish (23.38 ± 3.5g) were assigned to the following experiments: experiment 1 (latency to loss and recovery of the posture reflex): (a) 125 L-1, (b) 150 L-1, (c) 175 L-1, and (d) 200 L-1 (n = 9) per group. Experiment 2 (electrocardiographic and heartbeat recordings): (a) control group; (b) vehicle control group (2ml of alcohol per liter of water), (c) 125 L-1, (d) 150 L-1, (e) 175 L-1, and (f) 200 L-1 (n = 9), per group. All the concentrations used showed efficacy in inducing loss of the posture reflex and reversibility with recovery of the posture reflex, but the electrocardiographic recordings indicated morphographic changes such as bradycardia during induction and p wave apiculation during recovery at the highest concentrations tested. In this way, we suggest a safe use window for short-term anesthesia with EON in the concentration range of 125 to 150 L-1 for juvenile Colossoma macropomum.

Development And Validation of UV Spectrophotometric Method for The Estimation pf Amlodipine Besylate in Bulk and Dosage Form

A rapid, simple, accurate, and specific UV Spectrophotometric method has been developed for the determination of Amlodipine Besylate in bulk and dosage form. The spectrophotometric detection was carried out at an absorption maximum of 239 nm using dil. HCl as a solvent. The detector response for the Amlodipine Besylate was linear over the selected concentration range 4-20 µg/ml with a correlation coefficient of 0.999 and equation for the regression curve was found to be y= 0.109x + 0.006. These methods can be adopted in the routine assay analysis of Amlodipine Besylate API and pharmaceutical dosage form.