Computer Simulation Technology Microwave Studio Research Articles

Preparation and electromagnetic wave absorption of compressible graphene aerogels

In this study, a developed easy-operation method was adopted to generate ultralight and compressible graphene aerogels by using graphene oxide and ammonia. By changing the process parameters, such as reduction temperature, reducing agent content and ammonia concentration, the variation laws of the density and pore size of aerogels were obtained, which aided in realizing the controllable preparation of aerogel structures. The prepared graphene aerogel has good compressive performance, and its density can reach 5.26 mg/cm3. Although it was repeatedly compressed 200 times under a load that was 4000 times as large as its own weight, it maintained its structural integrity and mechanical properties. An ideal model of three-dimensional graphene aerogel was constructed, and the electromagnetic wave absorption performance was simulated using the Computer Simulation Technology (CST) Microwave Studio software. The results showed that when the thickness, pore size and height of the sheet were 1.4, 5 and 14 mm, respectively, an optimal electromagnetic wave absorption effect of −31.08 dB could be obtained. Furthermore, the effects of thickness, pore size and height of the sheet on the electromagnetic wave absorption performance are revealed, which provide a reference for the structural design of aerogels with both compressibility and electromagnetic wave absorption performance.

Radiation Pattern Reconfigurable Arch-Shaped Dual-Band Antenna for Wi-Fi and WLAN Applications

This paper describes the design and analysis of a reconfigurable radiation pattern dual-band antenna for Wi-Fi and WLAN applications. The antenna patch comprises two parts: the upper part, which consists of three symmetrical oval rings, and the lower part, which is shaped like a lotus flower. By controlling the ON and OFF states of lumped p-i-n switches to control the direction of the radiation beams, the proposed pattern reconfigurable antenna achieves three reconfigurable states. The beam's direction change is performed by two switches that are connected in the gap between the feedline and the arch. The proposed antenna operates at 2.4 and 5.5 GHz, covering the bands from 2.1882 to 2.55 GHz and from 5.31 to 5.96 GHz, respectively. Additionally, the directivity over the working bands is about 1.92 to 4 dBi while the gain lies in the range of 1.66 to 3.5 dB. Moreover, the voltage standing wave ratio (VSWR) varies from 1 to 1.20. The size of the antenna is 47×59.5 mm2 which is printed on a 1.6 mm thickness FR-4 substrate of 4.4 relative permittivity. Computer simulation technology Microwave Studio is used to design and study the recommended constructions. The proposed design achieves an acceptable value of VSWR, stable gain, and good directivity, which makes it a suitable choice for future radiation pattern reconfiguration applications. The proposed antenna is distinguished by a simple shape, compact size, respectable return loss, good radiation characteristics, and high efficiency. The obtained results from measurements are quite close to the simulations.

Polarization-independent tunable multi-band terahertz absorber based on graphene structure to design the ultra high sensitive biosensors

Abstract In this paper, we investigated the heterogeneous structure of a multi-band perfect absorber based on graphene in the terahertz range, benefiting from polarization independence. The proposed structure comprises three layers: copper, silicon dioxide, and an inhomogeneous graphene structure with an analyte. By altering the dimensions of the sub-layers and the geometric shape of the graphene slices, we can modify the number of bands, quality, and absorption levels. Additionally, adjusting the chemical potential of graphene enables the customization of absorption frequencies as needed. The application of this structure in biological sensors extends to the detection of proteins, viruses, cancer cells, as well as filtering telecommunication waves and imaging. Through geometrically shaping the graphene cuts at frequencies of 4.89 THz, 9.14 THz, and 10.76 THz, absorption values of 99.54%, 99.64%, and 98.3% have been achieved, respectively. Introducing the analyte to the biosensor structure causes a shift in absorption frequency values due to varying refractive index values in different materials. This property has been utilized for biosensor design. Within the refractive index range of biological analytes (e.g., 1.3), the first band achieved a sensitivity value of 2700 GHz/RIU and FoM = 13.08, while the second band achieved a sensitivity value of 2200 GHz/RIU and FoM = 14.02. An important characteristic of this structure is its insensitivity to polarization. Simulations were conducted using Computer Simulation Technology (CST) Microwave Studio Suite 2023.

Design and optimization of a Quasi‐Yagi antenna for 5G communications

AbstractA novel Quasi‐Yagi‐Uda antenna on a flexible material is designed and demonstrated in this paper. The antenna is developed on an ultra‐thin polyimide substrate to support dual‐frequency bands centered at 3.8 and 5.2 GHz for 5G and WiFi‐enabled wireless communications. The proposed Quasi‐Yagi‐Uda has a twin‐F‐shaped driven element which is excited using a microstrip line feed. The arms of the driven element are suitably designed to meet the frequency specifications of the proposed antenna. The design of the antenna is carried out using Computer Simulation Technology Microwave Studio while the antenna optimization is performed using the Fire‐Fly algorithm. The optimum geometrical details of the proposed antenna are obtained with a higher rate of convergence. The proposed dual‐band antenna provides 205 and 195 MHz bandwidth in both frequency bands guaranteeing high‐speed wireless communications in the 5G domain. The Quasi‐Yagi‐Uda provides a gain greater than 4.5 dBi in both operating bands with an efficiency greater than 80%. The prototype antenna optimized using the Fire‐Fly algorithm is fabricated and the simulation results are validated.

Improved design and performance of the global rectenna system for wireless power transmission applications around 2.45 GHz

This work proposes a new conception of the global microstrip rectenna system operating around 2.45 GHz. This improved rectenna system associates a receiving antenna with a rectifier circuit. This rectenna is printed on an FR4 substrate. The proposed antenna is a 1×4 microstrip antenna patch array with pentagonal patches using the defective ground structure method and operates with circular polarization. To show the effectiveness of this array, the results obtained by the computer simulation technology microwave studio (CST MWS) software prove that this array is good in terms of high gain, high directivity, high efficiency, wideband, small volume, and well-adaptation, and all these results are confirmed by another solver high-frequency structure simulator (HFSS). The improved rectifier is a microstrip rectifier that uses an HSMS2852 Schottky diode by using a series topology. The effectiveness of this rectifier is proved by the simulation results using advanced design system (ADS) software in terms of well-matching input impedance, high efficiency, and important output direct current (DC) voltage value. The proposed rectenna system is more efficient compared with the existing works and is very appropriate for several applications of wireless power transmission to power supply electronic instruments in various fields cleanly on our planet.

Predicting the coupling of HPEM waveform with a power amplifier in perforated conductive enclosure using FDDM/VF

AbstractOne of the most common methods to protect electronic and telecommunication systems in a high‐power electromagnetic (HPEM) environment is using a conductive enclosure. Amplifiers are the vital parts in transmitter and receiver systems as the main components of a telecommunication system, so investigating the effects of HPEM waveform on their performance is very important. The Presence of apertures in the body of the conductive enclosure, as well as non‐linear elements such as transistors in amplifiers, adds to the complexity of examining the coupling of electromagnetic fields on the performance of amplifiers. Considering the importance of the topic, in this study, the impact of the HPEM waveform on the power amplifier inside the conductive enclosure has been investigated. By using the finite difference delay modelling (FDDM) numerical method as a stable method followed by the vector fitting (VF) method, the electromagnetic problem has become a circuit problem, which allows examining the response of the power amplifier and any circuit, including non‐linear elements against the interference field. Responses of bipolar linear and non‐linear components in the perforated conductive enclosure by the proposed method have been compared with the results obtained by computer simulation technology microwave studio (CST‐MWS) for verification.

Design and Analysis of a Quad-Band Antenna for IoT and Wearable RFID Applications

The role of antennas in wireless communication is critical for enabling efficient signal transmission and reception across various frequency bands, including those associated with IoT (Internet of Things), X-band, S-band, and RFID (radio-frequency identification) systems. This paper presents a small quadruple-band antenna with 25 × 40 × 1.5 mm3 dimensions designed for diverse wireless applications. It is adept at operating in the S-band (2.2 GHz), wireless local area network (WLAN) (5.7 GHz), microwave RFID frequency band (5.8 GHz), and X-band (7.7 GHz and 8.3 GHz). While the majority of existing research focuses on antennas covering two or three bands, our work stands out by achieving quad-band operation in the proposed antenna design. This antenna is constructed on a semiflexible Rogers RT5880 substrate, making it well-suited for wearable applications. Computer Simulation Technology (CST) Microwave studio (2019) simulation package software is chosen for design and analysis. The antenna design features a comb-shaped radiating structure, where each “tooth” is responsible for resonating at a distinct frequency with an appropriate bandwidth. The antenna retains stability in both free space and on-body wearability scenarios. It achieves a low specific absorption rate (SAR), meeting wearable criteria with SAR values below 1.6 W/Kg for all resonating frequencies. The proposed antenna demonstrates suitable radiation efficiency, reaching a maximum of 82.6% and a peak gain of 6.3 dBi. It exhibits a bidirectional pattern in the elevation plane and omnidirectional behavior in the azimuth plane. The antenna finds applications across multiple frequencies and shows close agreement between simulated and measured results, validating its effectiveness.

Design of adaptive array using least mean square beamformer

<span>This paper introduces an 8-element linear array designed for adaptive array applications, using least mean square (LMS) algorithm to enhance the directivity of the array. Microstrip antenna has been optimized at 2.3 GHz, a pivotal frequency ranges relevant to 4G and 5G applications. This design is thoughtfully extended to encompass 8-elements, achieved through the art of parameterization using computer simulation technology (CST) microwave studio. This geometry of 8-element exhibits considerable promise, significantly elevating the gain from 6.13 dBi for a single element to an impressive 15.5 dBi for all eight-element array. To further empower the array’s adaptability and beam-steering capabilities, the LMS algorithm is simulated. This intelligent algorithm computes complex weights, thoughtfully with various angles, including those for the interested user at 60° and 30°, as well as potential interferers at 10° and 15°, as simulated in MATLAB. These meticulously calculated weights are effectively applied to antenna elements using CST, facilitating beam steering in various directions. During CST simulations, notable peaks in performance emerge at 54° and 28°, strategically aligned with nulls at 10° and 15°. Remarkably, these results exhibit a remarkable degree of concurrence with those obtained through MATLAB simulations, affirming effectiveness of the proposed adaptive array design.</span>

In silico, in vitro, and in vivo validation of a microwave imaging system using a low‐profile Ultra Wide Band Archimedean spiral antenna to detect skin cancer

AbstractMicrowave imaging (MI) is a noninvasive and nonionizing procedure for detection of cancerous cells in healthy body tissues using radiofrequency (RF) and microwaves. The procedure involves the use of Ultra Wide Band (UWB) antennas for sensing purposes. Therefore, this research article presents the design, development, and testing of a low‐profile UWB Archimedean spiral microstrip‐patch antenna (ASMA) for detection of skin cancer using monostatic radar‐based microwave imaging. The proposed ASMA consists of a spiral resonator with a defective ground structure and a slotted microstrip feed line with dimensions of 38 × 38 × 0.87 mm3. The proposed antenna shows an impedance bandwidth for the frequency range of 2.2–13.9 GHz, with a peak gain of 6.8 dB at 7.8 GHz. In silico analysis of the proposed ASMA for MI is carried out with Gaustav model using Computer Simulation Technology Microwave Studio. To validate the performance of the ASMA as a sensor for MI, a prototype of the same is fabricated and a four‐layered bio‐phantom of the human forearm is prepared for in vitro and in vivo testing of the proposed procedure. The validation of ASMA radiation properties is done using a Vector Network Analyser (E‐5063A) (VNA) and an anechoic chamber with the fabricated antenna at 10 mm away from the prepared bio‐phantom. The recorded S parameter data with bio‐phantom and the VNA is processed using different beamforming algorithms like Delay and Sum and Coherent Factor‐Delay Multiply and Sum (CF‐DMAS) to reconstruct the image of the scanned area. The reconstructed images are 97%–98% accurate. The proposed ASMA sensor is also safe for human exposure as it has a specific absorption rate of 0.0546 W/Kg at 5 GHz that complies with the safety guidelines of the Federal Communications Commission to minimize potential health risks associated with exposure to RF and microwave radiation.

A COMPACT 2 × 2 UWB-MIMO ANTENNA WITH FUNNEL SHAPED STUB FOR ISOLATION ENHANCEMENT

The growth of wireless communication technologies demands advancement in designing antennas. The essential need for efficient and low-profile antennas are required for wireless communication. The development of antenna structures(compact) with performances is considerably enhanced over traditional antenna structures and methodologies. A compact printed and planar multiple-input multiple-output (MIMO) for ultra wideband (UWB) communications is presented. Two circular disc monopole antenna elements constitute the proposed UWB-MIMO antenna, operating over the frequency band of 4-10 GHz. The required antenna performance in terms of frequency response, gain, S-parameters, and voltage standing wave ratio (VSWR) can be achieved in the range of 3-7 GHz gain with minimum attenuation. The proposed antenna is simulated using computer simulation technology (CST) microwave studio software, and the designed antenna will operate for wireless communication application.

Novel broadband circularly polarized pentagonal printed antenna design for wireless power transmission applications

<p>This paper provides a new conception for a microstrip patch antenna array that operates in a circularly polarized manner for wireless power transmission (WPT) at 2.45 GHz. The proposed conception combines four pentagonal patches and the defected ground structure (DGS) method. The antenna array with a dielectric constant of 4.4 and a tangential loss of 0.025 is printed on a FR4 where its thickness is about 1.58 mm. The developed design aims to optimize the antenna array performance. Th e main contribution, to the telecommunications and WPT fields, is to achieve a maximum energy transfer with low losses, while also ensuring adequate adaptation to the excitation port. To prove the effectiveness of this design, simulation results were obtai ned using computer simulation technology microwave studio (CST MWS) software and validated by another solver high - frequency structure simulator (HFSS). Simulation results are presented and compared with those obtained using existing conceptions in the lite rature. The proposed design has proven to be very effective in achieving the intended objectives, which makes this design very good for radiofrequency (RF) energy collection and its various applications to power a variety of devices without harming our pla net.</p>

High-performance THz Metallic Axial Mode Helix Antenna with Optimised Truncated Hollow Cone Ground Plane for 6G Wireless Communication System

The Terahertz (THz) band antenna configuration operates in the 0.1–10 THz frequency range and offers a stable performance for future 6th Generation (6G) wireless communication systems. However, the available metallic axial mode helix antenna designs exhibit a peak directivity of lower than 18 dBi within 0.5–1 THz, making it inappropriate to be applied in wireless communication systems. Therefore, this study proposed a high-performance THz metallic five-turn axial mode helix antenna with an optimised truncated hollow cone ground plane for 6G wireless communication systems. Following the creation of the proposed antenna design using cost-effective copper (annealed), the truncated hollow cone ground plane of the THz axial mode helix antenna was optimised via simulation in a Computer Simulation Technology Microwave Studio (CST MWS) software and a verification of the proposed THz antenna design in Analysis System High-Frequency Structure Simulator (Ansys HFSS) software for a fair comparison. Based on the results, the proposed THz metallic axial mode helix antenna with optimised truncated hollow cone ground plane recorded an impedance bandwidth of 0.46 THz, Fractional Bandwidth (FBW) of 61.33% for |S11| ≤ -10 dB, and a maximum directivity and realised gain of 21.8 dBi and 21.5 dBi at 0.85 THz, respectively. Within the 0.5–1 THz, the proposed optimised THz antenna design achieved an outstanding performance, including an FBW of more than 50%, excellent directivity of higher than 15.8 dBi, radiation efficiency of greater than 87%, circular polarisation, and low-profile helix turns. In short, the proposed THz metallic axial mode helix antenna with optimised truncated hollow cone ground plane design is appropriate for various THz 6G wireless applications.

Design and implementation of a frequency reconfigurable antenna using PIN switch for sub-6 GHz applications

Abstract The future of 5G New Radio development has many significant concerns. We present and investigate a frequency-reconfigurable antenna based on a PIN diode to overcome the working frequency band issue. The dimensions are 30 mm × 20 mm × 1.6 mm, built on material substrate (FR-4) with a relative permittivity of ε r {\varepsilon }_{{\rm{r}}} = 4.4. Two switches allow frequency reconfiguration in the antenna, giving us three operation modes. The design in mode 1 (SW1 = Off and SW2 = Off) covers a 4.6 GHz band. The proposed design in mode 2 resonated at 2.7 and 4.8 GHz (SW1 = On, SW2 = Off or SW1 = Off, SW2 = On), while the design in mode 3 operated at 3.6 GHz (SW1 = On, SW2 = On). Before fabrication, the proposed design is simulated by the Computer Simulation Technology microwave studio software. The presentation and discussion of the radiated pattern and S parameter demonstrate the practicability of the proposed design. The design module’s dimensions and performance are both precisely appropriate. The results indicate a good agreement between both simulation and experimental findings.

Exploiting Surface Plasmon with Dielectric Coating in Copper Wires Waveguide for the Propagation of Terahertz Waves

Recently, metallic wires have gained popularity for utilization as waveguides in propagating sub-THz and THz waves through surface plasmonic polaritons (SPPs). Single and double metallic wire waveguides have demonstrated the ability to propagate these high frequencies with minimal loss and nearly zero dispersion. However, wires typically installed commercially are often coated with dielectric material. Therefore, this paper investigated the effects of using two and four metallic copper wires, both with and without dielectric coating. The impact of various gap distances on different propagation characteristics was also analyzed. Computer Simulation Technology (CST) Microwave Studio was employed in this study for electromagnetic simulations of both uncoated and coated configurations of two and four wires. The introduction of a dielectric coating led to an enhancement in reducing conductor losses and improving energy confinement, with the goal of enhancing the overall efficiency of waveguide signal propagation.

Dual-band absorption due to simultaneous excitation of TE and TM modes in ITO-ES metamaterial for IR stealth technology

We proposed a plasmonic based Indium Tin Oxide Embedded Silver (ITO-ES) infrared dual-band perfect absorber for the utilization in IR stealth technology. The proposed structure comprised of nano size Ag ring and desk embedded in ITO. The optical losses in optical regime of nanoscale plasmonic Ag were incorporated in terms of collision frequency using the modified Drude model. The optical response of the proposed structure was predicted by exciting it with a planwave using full wave vector frequency domain solver by employing Finite Element Method (FEM) in Computer Simulation Technology (CST) Microwave Studio. The simultaneous excitation of higher order transverse electromagnetic (TE and TM) modes in the proposed structure lead to high values of both absorption and Front to Back ratio (FTBR). The controlled and selective wavelength multiband absorption is crucial for IR stealth technology. The proposed metamaterial structures exhibit dual-bands IR absorption at wavelengths λ = 1.40 μm and 6.4 μm. First absorption peak suppresses the back scattering of the laser used by laser guided devices for detection, while the second peak suppresses the IR signature of the structure due thermal radiation which can be used by tracking devices to detect warm/hot objects.

A microstrip patch antenna for 5G mobile communications

The advantages of microstrip patch antennas include small size, adaptable surface, ease of fabrication, and compatibility with integrated circuit technology. Numerous experiments have been done over the past few decades to enhance the performance of this antenna, and both military and commercial sectors have found many uses for it. This paper introduces a microstrip patch antenna with an operating frequency of 28GHz for 5G mobile communication. This research designed and simulated a rectangular microstrip patch antenna with 3.494 mm * 5.3 mm * 0.003 mm. The proposed antenna resonates at 28 GHz with a reflection coefficient of -24 dB, a bandwidth of 280 MHz, and a gain of 2.2 dBi. The inset feed technique matches the 50 Ω transmission line impedance. In the design, Rogers RT5880 substrate and copper ground are used. The antenna’s geometry was calculated, and simulated results were analyzed using Computer Simulation Technology Microwave Studio. In conclusion, the proposed antenna has a reflection coefficient of -24 dB, VSWR of 1.24, an input impedance of 51.6Ω, and a gain of 2.2 dBi at operating frequency with a compact geometry can be used in 5G mobile communications. The future shift in resonance frequencies and beams can be considered to make the antenna operate as a smart antenna.

6G Broadband and High Directive Microstrip Antenna with SIW and FSSs

Sixth-Generation (6G) wireless communication networks require the fabrication of broadband and high directivity microstrip antennas to offset the high atmospheric path loss beyond 100 Gigahertz (GHz). In this paper, we designed and proposed a couple of high-gain and broadband microstrip array antennas that have been designed within a Finite Integration Technique (FIT) solver at Computer Simulation Technology Microwave Studio (CST MWS) software in a series-parallel feeding method for a resonance frequency above 107 GHz. A Substrate-Integrated Waveguide (SIW) with dual outputs has been used at these antennas and with WR-08 waveguide that covers the 90-140 GHz frequency range, while the first was without Frequency Selective Surfaces (FSSs), and the second was with the FSSs to increase the antenna directivity further. The first design was simulated with a Finite Element Method (FEM) solver at Ansys High-Frequency Structure Simulator (HFSS) to compare the simulation results of this antenna. This comparison's peak gain and Bandwidth (BW) were correspondingly 25.3 dB, 12.5 GHz, 23.1 dB, and 11 GHz from the Ansys HFSS and the CST MWS. Thus, the accuracy and the slight deviation of the compared simulation results from each other validated the offered 6G antenna designs. Therefore, after experimental verification, the proposed antennas can be employed in 6G future wireless communication networks.

Linear Antenna Array Sectorized Beam Scanning Approaches Using Element Position Perturbation in the Azimuth Plane.

In this paper, two sector beam scanning approaches (BSAs) based on element position perturbations (EPPs) in the azimuth plane are introduced. In EPP-BSA, the elements' excitations are kept constant and the elements' positions in the direction normal to the array line are changed according to a predetermined EPP pattern. The magnitude and repetition rate of the selected EPP pattern determines the steering angle of the main beam. However, EPP-BSA results in a wide scanning range with a significant increase in the side lobe level (SLL). To mitigate this drawback, a reduction in the SLL of the array pattern is firstly performed using the single convolution/genetic algorithm (SC/GA) technique and then perturbing the elements' positions in the azimuth plane. This combination between SLL reduction and EPP-BSA (SLL/EPP-BSA) results in a smaller scanning range with a relatively constant half power beamwidth (HPBW) and a much lower SLL. In addition, keeping the synthesized excitation coefficients constant without adding progressive phase shifters facilitates the manufacturing process and reduces the cost of the feeding network. Furthermore, a planar antenna array thinning approach is proposed to realize the EPP-BSA. The results are realized using the computer simulation technology (CST) microwave studio software package, which provides users with an optimized modeling environment and results in realizable and realistic designs.

Testing of chlorine dosage in drinking water using microstrip patch sensor

A new method using microstrip patch sensor is designed, simulated, and measured to detect the dosage of added chlorine to the drinking water using the relation between permittivity and matching impedance. The simulation is done using computer simulation technology-microwave studio software. The proposed sensor is designed on a single FR-4 layer with a low profile, 0.499 GHz bandwidth, center frequency of 2.94 GHz, gain of 6.55 dBi, and a good front to back ratio of 17.84 dB. In this work, the antenna design is started from a conventional patch antenna equation. Then, an optimization process is performed to achieve good parameter values for obtaining the desired objective. The objective is to utilize the microwave frequency to measure the chlorine dosage in water. The measurement results proved that the matching impedance can be used to find out the dosage of chlorine in drinkable water. The proposed method overcomes the open-ended coaxial probe method in terms of experimental time and contactless testing and shows high matching with the latter actual data. Moreover, the proposed method overcomes the conventional methods in terms of continuity and large scale of testing, non-contacting with the samples of water, and no additive chemical materials, which make the water samples not drinkable.

Design of 60 GHz millimeter‐wave SIW antenna for 5G WLAN/WPAN applications

AbstractBroadband millimeter Wave (mmWave) transmission at the 60 GHz band is a great prospect to meet the demanding high data rate requirements of future wireless personal area network (WPAN) and wireless local area network (WLAN) 5G networks. This paper proposes a single layer H‐plane sectoral horn mmWave antenna at 60 GHz using substrate integrated waveguide (SIW) technology for the future high‐speed short range WPAN and WLAN networks. The benefits of the proposed antenna are high gain, low cost, small size, and ease of integration with other planar circuits. The proposed SIW horn is constructed with RT/duroid 5880 substrate, which has a relative permittivity and loss tangent with a thickness of 0.508 mm. The novelty of this work is; a wider bandwidth is achieved by adding striplines at the horn aperture to match the antenna with air and to increase the antenna operating bandwidth. In addition, the antenna gain is improved by adding a dielectric lens with the striplines at the radiating end. During these steps, the antenna parameters are tuned and optimized to achieve the best results as compared to related previous studies. The proposed antenna's performance is analyzed in terms of gain, return loss (S11) and radiation pattern at a frequency of 60 GHz. Simulation results are carried out by using industry standard software, Computer Simulation Technology (CST) microwave studio. The designed antenna achieves a peak gain of 13 dB and impedance bandwidth when , 8.6 GHz (13.688%) for the reflection coefficient of . The results show that the proposed antenna achieves stable tunable 60 GHz frequency performance, which makes it feasible to deploy in WLAN/WPAN operating in mmWave bands.