Collapse Of Cavitation Bubbles Research Articles

LBM study of ice nucleation induced by the collapse of cavitation bubbles

In this study, we extended the conventional lattice Boltzmann method (LBM) to numerically examine ice nucleation induced by the collapse of a cavitation bubble. Specifically, a pseudo-potential multi-relaxation-time lattice Boltzmann method (MRT-LBM) coupled with a thermal LBM and a criterion for pressure-dependent ice nucleation onset was developed to investigate the cavitation bubble dynamics including growth and collapse, and the subsequently induced ice nucleation. Using the present model, the water vapour-liquid coexistence curve was extended to temperatures lower than 42% of its critical point, excellently matching the Maxwell construction curve. Two practical application scenarios of ice nucleation were investigated: I, near a solid boundary and II, within a pressurised space. Effects of key system parameters including the stand-off distance (λ), differential pressure (Δp) and initial bubble size (R0) on the maximum collapse pressure (pmax) were examined. The results show that under the same conditions, a much higher pmax is generated in scenario II than that in scenario I, thus more readily initialises ice nucleation. After initialisation, part of the initially formed ice melts when the local temperature exceeds the ice melting temperature due to the rapid dissipation of pressure wave. To ensure the complete freezing of water, a large initial supercooling is required for scenario II.

Numerical study of the synergistic effect of cavitation and micro-abrasive particles

In ultrasonic-assisted machining, the synergistic effect of the cavitation effect and micro-abrasive particles plays a crucial role. Studies have focused on the investigation of the micro-abrasive particles, cavitation micro-jets, and cavitation shock waves either individually or in pairs. To investigate the synergy of shock waves and micro-jets generated by cavitation with micro-abrasive particles in ultrasonic-assisted machining, the continuous control equations of a cavitation bubble, shock wave, micro-jet, and micro-abrasive particle influenced by the dimensionless amount (R/R0), a particle size-velocity–pressure model of the micro-abrasive particle was established. The effects of ultrasonic frequency, sound pressure amplitude, and changes in particle size on micro-abrasive particle velocity and pressure were numerically simulated. At an ultrasonic frequency of 20 kHz and ultrasonic sound pressure of 0.1125 MPa, a smooth spherical SiO2 micro-abrasive particle (size = 5 µm) was obtained, with a maximum velocity of 190.3–209.4 m/s and pressure of 79.69–89.41 MPa. The results show that in the range of 5–50 μm, smaller particle sizes of the micro-abrasive particles led to greater velocity and pressure. The shock waves, micro-jets, and micro-abrasive particles were all positively affected by the dimensionless amount (R/R0) of cavitation bubble collapse, the larger the dimensionless quantity, the faster their velocity and the higher their pressure.

Study on the Motion Characteristics of Solid Particles in Fine Flow Channels by Ultrasonic Cavitation.

Microjets caused by the cavitation effect in microchannels can affect the motion trajectory of solid particles in microchannels under ultrasonic conditions. The optimal parameters for an observation experiment were obtained through simulations, and an experiment was designed to verify these parameters. When the cavitation bubbles collapse in the near-wall area, the solid particles in the microchannel can be displaced along the expected motion trajectory. Using fluent software to simulate the bubble collapse process, it can be seen that, when an ultrasonic sound pressure acts on a bubble near the wall, the pressure causes the top of the bubble wall to sink inward and eventually penetrate the bottom of the bubble wall, forming a high-speed microjet. The maximum speed of the jet can reach nearly 28 m/s, and the liquid near the top of the bubble also moves at a high speed, driving the particles in the liquid towards the wall. A high-speed camera was used to observe the ultrasonic cavitation process of bubbles in the water to verify the simulation results. A comparison of particle motion with and without ultrasonic waves proved the feasibility of using the ultrasonic cavitation effect to guide small particles towards the wall. This method provides a novel experimental basis for changing the fluid layer state in the microchannel and improving precision machining.

Cavitation bubble collapse in a vicinity of a rigid wall with a gas entrapping hole

This paper aims to reveal the influence of a rigid wall with a gas entrapping hole on the characteristics of the dynamic behavior of a laser-induced bubble collapse. A high-speed camera system was used to record the oscillation process of the laser-induced bubble on a rigid wall with a gas entrapping hole. When a bubble is generated by a laser above the wall with a gas entrapping hole, the entire bubble collapse stays away from the wall or splits into two bubbles because of a radial jet induced by bubble contraction. These two distinctive collapse modes are dependent on the distance between the wall and the bubble. The focus of this study is the quantitative analysis of the jet formation, bubble migration, and oscillation period, and compared with the behavior of the bubble near a rigid wall. The results show that unlike the generation of the bubble near a rigid wall, a rigid wall with a gas entrapping hole affects the morphology of the jet and changes the direction of migration of the bubble and decreases the oscillation period. Thus, the rigid wall with a gas entrapping hole could be effective for reducing cavitation erosion on the wall surface, which is supported by our experiment results.

Ultrahigh Performance Self‐Supported Cl‐Cu2O@Cu Foam Electrode Fabricated by Sonochemical Surface Reconstruction Approach

AbstractUnlike powdery transition metal oxide (TMO) coated electrodes, self‐supported TMO electrodes have attracted considerable interests for optimizing the electrocatalytic performances of electrodes due to sufficient exposure of active sites and improved TMO‐substrate interfaces. However, conventional manufacture methods for self‐supported electrodes are faced with inefficiency and high complexity. Herein, a facile sonochemical surface reconstruction approach is proposed to fabricate Cl‐doped Cu2O@Cu foam (Cl‐Cu2O@Cu) electrode with ultrahigh sensitivity for glucose sensing. The intensive collapse of cavitation bubbles near Cu foam under sonication within NH4Cl solution, for this reason, massive Cu complex ions and highly active Cu surfaces are simultaneously generated. Then the nanosized Cu2O particles with large active surfaces are in situ formed and tightly anchored on the Cu surface, which undergoes Cl doping in Cu2O, resulting in ascending electrical conductivity. The Cl‐Cu2O@Cu electrode shows excellent catalytic performance to glucose, presenting ultrahigh sensitivity of 28 mA cm−2 × 10−3 m and ultralow limit of detection of 0.35 × 10−6 m (S/N = 3). This work promotes a novel approach for the rational design of self‐supported electrochemical electrodes by sonochemistry.

Особенности наложения ультразвуковых колебаний в процессе сварки

Introduction. The main problem in obtaining welded joints is the nonuniform heating of the joint zone, which leads to differences in the structure and properties of the weld metal and the base metal. One of the ways to intensify the welding process is the use of ultrasonic vibrations. As a result of the analysis of methods for introducing ultrasonic vibrations into the melting zone, a method of superimposing vibrations on the elements to be welded was chosen for experimental studies. This method makes it possible to influence the welded elements throughout the entire welding cycle from the melt bath to complete crystallization of the metal. Methods. Experimental studies were carried out on plates made of carbon structural steel St3 (ASTM A568M, AISI 1017, DIN 17100) and aluminum deformable non-hardened alloy AMg4 (EN AW-5086, AW-AL Mg4, 5086). As a source of oscillations, a rod magnetostrictive oscillatory system was used, the end of which was rigidly fixed on one of the welded plates. To determine the places of application of the oscillation source and the welding zone, a calculation method is proposed based on the equality of the resonant frequencies of the used oscillatory system and the natural frequency of bending vibrations of the welding component. It is shown that the optimal places for the application of vibrations and welding will be the antinodes of oscillations, which have the maximum amplitude. Welds were obtained by the method of semi-automatic gas metal arc welding. Results and Discussion. Microstructural study of obtained samples showed a significant decrease in the proportion of dendritic segregation. The changes in the structure are the result of the effects that occur in the liquid melt when ultrasonic vibrations are introduced. The main effects are sound pressure, cavitation and acoustical streaming. The structure change mechanism consists in the dispersion of growing dendrites and crystallization nuclei under the action of shock waves and cumulative jets that occur when cavitation bubbles collapse. The formed fragments of dendrites are new crystallization nuclei that propagate through the melt pool under the action of acoustic currents. Then the process is repeated. The resulting effects affect the kinetics of the crystallization process – the degree of supercooling increases, the number of crystallization nuclei formed per unit time increases, and the rate of its growth decreases. Changes in the structure of the weld metal lead to an increase in the quality of the welded joint, which reduces welding deformations, increases the tensile strength and significantly increases ductility.

Large cavitation bubbles in the tube with a conical-frustum shaped closed end during a transient process

The transient process accompanied by extreme acceleration in conical sections of hydraulic systems (e.g., draft tube, diffuser) can induce large cavitation bubbles both at the closed ends and in the bulk liquid. The collapses of the large cavitation bubbles can cause severe damage to the solid walls. We conduct experiments in the tubes with different conical-frustum shaped closed ends with the “tube-arrest” method and observe bubbles generated at these two locations. For the bubbles generated at the close end of the tube, we propose the onset criteria, consisting of two universal non-dimensional parameters Ca1 and Ca2, of large cavitation bubbles separating the water column. We investigate their dynamics including the collapse time and speed. The results indicate that the larger the conical angle, the faster the bubbles collapse. For the bubbles generated in the bulk liquid, we numerically study the collapse time, the jet characteristics, and the pressure pulse at the bubble collapse. We observe a much stronger jet and pressure pulse of bubbles in tubes, comparing with a bubble near an infinite plate. Our results can provide guidance in the design and safe operation of hydraulic machinery with complex geometries, considering the cavitation during the transient process.

An ultrasonically actuated fine-needle creates cavitation in bovine liver.

Ultrasonic cavitation is being used in medical applications as a way to influence matter, such as tissue or drug vehicles, on a micro-scale. Oscillating or collapsing cavitation bubbles provide transient mechanical force fields, which can, e.g., fractionate soft tissue or even disintegrate solid objects, such as calculi. Our recent study demonstrates that an ultrasonically actuated medical needle can create cavitation phenomena inside water. However, the presence and behavior of cavitation and related bioeffects in diagnostic and therapeutic applications with ultrasonically actuated needles are not known. Using simulations, we demonstrate numerically and experimentally the cavitation phenomena near ultrasonically actuated needles. We define the cavitation onset within a liver tissue model with different total acoustic power levels. We directly visualize and quantitatively characterize cavitation events generated by the ultrasonic needle in thin fresh bovine liver sections enabled by high-speed imaging. On a qualitative basis, the numerical and experimental results show a close resemblance in threshold and spatial distribution of cavitation. These findings are crucial for developing new methods and technologies employing ultrasonically actuated fine needles, such as ultrasound-enhanced fine-needle biopsy, drug delivery, and histotripsy.

Explosive Vaporization of Ethanol on Microheater during Pulse Heating

The article is devoted to the research of transient heat transfer, explosive vaporization and condensation in subcooled ethanol on microheater during pulsed heating. Experiments were performed using high-speed infrared thermography and visualization for various initial liquid temperatures 30–60 °C and heat fluxes in the range of 3.3–7.8 MW/m2. The evolution of temperature field of the microheater and liquid during transient heating and the nucleation temperatures for different heat fluxes and liquid subcooling were determined. It was shown that the nucleation temperature was almost independent on heating power and amounted to 194 °C, which is close to the calculations based on homogeneous nucleation theory. New experimental data were obtained on the times of convection and boiling onset, evolution of vapor bubbles, including the dependence of their maximum sizes on the heat flux and initial liquid temperature. It was shown that the maximum bubble size decreases with an increase in the heat flux and liquid subcooling, varying in the same range as for water. It was demonstrated that at low heat fluxes, during condensation, a liquid funnel was formed at the bubble top, which resembled the formation of a liquid jet during the collapse of cavitation bubbles.

Numerical Modeling of Propagation of an Outgoing Shock Wave Produced at Cavitation Bubble Collapse

Numerical Modeling of Propagation of an Outgoing Shock Wave Produced at Cavitation Bubble Collapse

Influence of the Tetradecane Temperature and Pressure on the Formation of Radially Converging Shock Waves Inside a Collapsing Cavitation Bubble

Influence of the Tetradecane Temperature and Pressure on the Formation of Radially Converging Shock Waves Inside a Collapsing Cavitation Bubble

Laser-induced microjet-assisted ablation for high-quality microfabrication

Liquid-assisted laser ablation has the advantage of relieving thermal effects of common laser ablation processes, whereas the light scattering and shielding effects by laser-induced cavitation bubbles, suspended debris, and turbulent liquid flow generally deteriorate laser beam transmission stability, leading to low energy efficiency and poor surface quality. Here, we report that a continuous and directional high-speed microjet will form in the laser ablation zone if laser-induced primary cavitation bubbles asymmetrically collapse sequentially near the air-liquid interface under a critical thin liquid layer. The laser-induced microjet can instantaneously and directionally remove secondary bubbles and ablation debris around the laser ablation region, and thus a very stable material removal process can be obtained. The shadowgraphs of high-speed camera reveal that the average speed of laser-induced continuous microjet can be as high as 1.1 m s−1 in its initial 500 μm displacement. The coupling effect of laser ablation, mechanical impact along with the collapse of cavitation bubbles and flushing of high-speed microjet helps achieve a high material removal rate and significantly improved surface quality. We name this uncovered liquid-assisted laser ablation process as laser-induced microjet-assisted ablation (LIMJAA) based on its unique characteristics. High-quality microgrooves with a large depth-to-width ratio of 5.2 are obtained by LIMJAA with a single-pass laser scanning process in our experiments. LIMJAA is capable of machining various types of difficult-to-process materials with high-quality arrays of micro-channels, square and circle microscale through-holes. The results and disclosed mechanisms in our work provide a deep understanding of the role of laser-induced microjet in improving the processing quality of liquid-assisted laser micromachining.

Use of mesoporous BiOI microspheres for sonocatalytic degradation of tetracycline hydrochloride

Self-assembled mesoporous BiOI microsphere with nanosheets were prepared by a solvothermal method and used as sonocatalysts. The sonocatalytic performances of the BiOI microspheres were evaluated in terms of the degradation rate of tetracycline hydrochloride (TCH) as a model pollutant. We designed three comparative experiments to explore the degradation of TCH solution under natural light, namely with sonication, with BiOI alone, and with ultrasound (US)/BiOI synergy. The degradation rate of TCH with US/BiOI synergy was 227 times higher than that achieved with sonication and 83 times higher than that achieved with BiOI alone. The maximum TCH degradation rate was 93.0%. The synergistic effect was therefore significant, and the synergy factor was estimated to be 61. Many factors such as the ultrasonic duty cycle, applied power, catalyst concentration, and initial TCH dye concentration may affect the ultrasonic degradation efficiency. Box–Behnken design of the response surface method were used to optimize the parameters and to study the effects of the catalyst concentration, ultrasonic duty cycle, and applied power. Analysis of variance confirmed that the quadratic response surface model for predicting the sonocatalytic efficiency was good for the corresponding parameters (R2 = 0.9936 and adjusted R2 = 0.9854). The optimization results were verified by replicate experiments. The high TCH degradation rate may be related to the generation of reactive oxygen species at the end of cavitation bubble collapse, which can improve the chemical yields.

Experimental and numerical investigations of the collapse of a laser-induced cavitation bubble near a solid wall

Experimental and numerical investigations of the collapse of a laser-induced cavitation bubble near a solid wall

Deagglomeration of spray-dried submicron particles by low-power aqueous sonication

The resistance to deagglomeration of spray-dried agglomerated particles of submicron size was investigated using an ultrasonication system in water. Submicron agglomerates consisting of water-insoluble primary particles with size of 10 or 100 nm were prepared in different shapes by varying the heating profile during spray drying. Deagglomeration experiments were performed using a low-power sonication device. Spherical agglomerates were found to be more resistant to ultrasonic forces, while dent- or doughnut-shaped agglomerates tended to break down. The results show that the shape of the agglomerate plays an important role in the energy balance of the ultrasound operation. The energy produced from the collapse of cavitation bubbles in the ultrasound vessel may be used to promote motion of the agglomerates and deagglomeration.

Observation of the Formation of Multiple Shock Waves at the Collapse of Cavitation Bubbles for Improvement of Energy Convergence

The collapse of a cavitation bubble is always associated with the radiation of intense shock waves, which are highly relevant in a variety of applications. To radiate a strong shock wave, it is necessary to converge energy at the collapse, and understanding generation processes of multiple shock waves at the collapse is a key issue. In the present study, we investigated the formation of multiple shock waves generated by the collapse of a laser-induced bubble. We used a high-speed imaging system with unprecedented spatiotemporal resolution. We developed a triggering procedure of high precision and reproducibility based on the deflection of a laser beam by the shockwave passage. The high-speed videos clearly show that: (A) a first shockwave is emitted as the micro-jet hits the bottom of the bubble interface, followed by a second shock wave due to the collapse of the remaining toroidal bubble; (B) a sequential collapse of elongated bubbles, where the top part of the bubble collapses slightly before the bottom of the bubble; and (C) the formation of compression shock waves from multiple sites on a toroidal bubble.

Role of wall temperature on cavitation bubble collapse near a wall investigated using thermal lattice Boltzmann method

The thermal lattice Boltzmann method can be adopted to simulate cavitation bubble collapse in heating or cooling systems. The numerical results satisfy Laplace's law and are consistent with temperature solutions derived from the Rayleigh–Plesset equation. In this paper, in order to study the effects of wall temperature on a collapsing bubble, a calculation model for a cavitation bubble near the heated/cooled wall is established. The influence mechanism of the micro-jet and the cavitation bubble itself on the solid-wall heat transfer, and the thermodynamic behavior characteristics of the cavitation bubble collapse near the wall are obtained. Adjusting the wall temperature Tw also affects the thermal effects of cavitation. Furthermore, A dimensionless temperature parameter η is introduced to study the heat transfer intense of the model. The influence of λ, Δp and R0 on the heat transfer intense are studied and analyzed. The results show that the optimal λ, Δp, R0 and Tw values can be used to enhance heat transfer and realize heating or cooling treatment of different surfaces.

Study of surface tension effects on near-wall cavitation bubble collapse with a pseudopotential lattice Boltzmann model

A lattice Boltzmann pseudopotential cavitation model with tunable surface tension and large density and viscosity coefficient ratios was used to simulate near-wall cavitation bubble collapse. The influences of the surface tension, bubble–wall distance, and initial pressure difference on the flow field distribution were analyzed, and the relationships between the surface tension and maximum micro-jet and collapse pressure were investigated. The results indicated that a lower surface tension intensifies the deformation of the gas–liquid interface, resulting in a more concentrated micro-jet. In addition, more surface energy is accumulated during cavitation bubble collapse for higher surface tension, strengthening the collapse intensity and increasing the maximum micro-jet velocity and collapse pressure. The time interval between the first and second pressure peaks increases with increasing wall distance. Because of the non-linear attenuation during pressure propagation, the value of the second peak decreases with increasing wall distance. Increasing the initial pressure difference leads to slower growth in the micro-jet velocity and faster growth in the collapse pressure with increasing bubble–wall distance. In addition, increasing the initial pressure difference for the same bubble–wall distance also slows the growth in the micro-jet velocity and increases the growth in the collapse pressure caused by increasing surface tension.

Removal of Inorganic Salts in Municipal Solid Waste Incineration Fly Ash Using a Washing Ejector and Its Application for CO2 Capture.

This study investigated the effects of washing equipment for inorganic salts, such as NaCl, KCl, and CaClOH, to decontaminate municipal solid waste incineration fly ash (MSW-IFA). Based on the feature of hydrodynamic cavitation, the device developed in this study (referred to as a ‘washing ejector’) utilizes the cavitation bubbles. A washing ejector was analyzed under a range of conditions, employing as little water as possible. In hydrodynamic cavitation, the increase in fluid pressure with increasing static pressure is mainly attributed to the increase in particle–bubble collisions via the cavitation flow. The results revealed that the fluid pressure influenced the removal of inorganic salts during cavitation in water. This is because during the washing process from the collapse of cavitation bubbles, the release is achieved through the dissolution of inorganic salts weakly bound to the surface. After treatment by a washing ejector, the removal of soluble salts elements such as Cl, Na, and K was reduced by approximately 90%. Removing the inorganic salts in the IFA altered the characteristics of the Ca-related phase, and amorphous CaCO3 was formed as the cavitation flow reacted with CO2 in the ambient air. Furthermore, the washing effluent produced by washing IFA was found to be beneficial for CO2 capture. The washing effluent was enriched with dissolved Ca from the IFA, and the initial pH was the most favorable condition for the formation of CaCO3; thus, the effluent was sufficient for use as a CO2 sequestration medium and substitute for the reuse of water. Overall, the process presented herein could be effective for removing soluble salts from IFA, and this process is conducive to utilizing IFA as a resource.

Numerical investigation of ozone decomposition by self-excited oscillation cavitation jet

Abstract Extreme environmental changes caused by the cavitation bubble collapse, such as high pressure, high temperature and the microjet, will cause pyrolysis reaction at the gas and liquid interface inside the bubble. Self-excited pulsed cavitation jet has an instantaneous strong pulse pressure, which leads to local hot spots surrounding the cavitation bubbles. The generation of strong oxidizing free radicals promotes easy ozone conversion into oxygen. Numerical simulations were conducted for ozone decomposition by cavitation jet. Three groups of different collision angles were applied to compare and analyze the ozone degradation reaction. Results showed that the collision angle has a certain influence on the chemical reaction intensity, the degradation of ozone, and oxygen production. At the collision angle of 180°, the chemical reaction was the most violent, with ozone degradation and oxygen production at the highest level, followed by 120° and lowest at 90°.