Co-precipitation Route Research Articles

Investigation of photocatalytic degradation of diclofenac sodium and acetaminophen by Zn-Ag co-doped barium hexaferrite@CNTs Composite

Herein, a facile coprecipitation route was followed to synthesize Zn-Ag co-doped barium hexaferrite (ABHF) and its nanocomposite with carbon nanotubes (CNTs) using the ultrasonication method. Various characterization techniques were used to analyze the structure and optical properties. The bandgap energy of BHF and ABHF was 2.16 eV, and 2.09 eV respectively. Diclofenac sodium and acetaminophen were used to study the photocatalytic activity of the synthesized samples. It was noted that the bare sample showed 29.46 % and 44.96 % degradation for diclofenac sodium and acetaminophen respectively. The highest catalytic activity was shown by the nanocomposite (ABHF@CNTs) that degraded 70.87 % and 84.34 % of diclofenac sodium and acetaminophen respectively. Photodegradation of diclofenac sodium and acetaminophen (pharmaceutical drugs) was increased due to a reduction in bandgap energy (Eg), increased surface area, and prolonged e--h+ pair recombination of the synthesized samples.

Synergetic effects of Al addition on the performance of CoFe2O4 catalyst for hydrogen production and filamentous carbon formation from direct cracking of methane

Improving methane catalytic decomposition process was deemed an effective approach for hydrogen production. Here, a novel catalyst AlxCo1-xFe2O4 with a variable aluminum content was synthesized via a co-precipitation route for the direct cracking of methane. The catalytic activity of AlxCo1-xFe2O4 was performed in a fixed bed reactor at temperature of 800°C and 20 mL/min of fed gas. A sequence of characterizations, including SEM, BET, XRD, XPS, Raman and TGA for fresh and spent catalysts, was exploited to examine the influence of Alx content on the morphology, porosity, structure, chemical composition, and cation distribution of AlxCo1-xFe2O4. As the Alx content increased in AlxCo1-xFe2O4 their morphology became more fractal and decreased in particle size, lattice parameter, lattice size, while their pore surface increased. Further cation re-distributions from octahedral to tetrahedral sites as Fe3+ and Al3+ relocated in the Tetrahedral site and Oxygen lattice decreased as observed from Raman and XPS results. Catalytic activity studies showed that Alx content of 0.6 in AlxCo1-xFe2O4 lead maximum methane conversion up to ∼ 91.10 % and hydrogen formation rate of 1.780 ×10-3 mol H2 g-1 s-1. The catalytic activity behavior was explained in correlation with the characteristics of spent catalysts.

Investigation of cerium as a surrogate for tetravalent actinides in monazite-type compounds

The incorporation of tetravalent cerium into the monazite structure via Ca(II)-coupled substitution was investigated using a solid state and a co-precipitation route for the synthesis of the La1-2xCaxCexPO4 solid solution. Based on powder XRD measurements and elemental mappings an optimised synthesis procedure was developed that averts the formation of secondary phases and allows the stabilisation of tetravalent cerium with a ratio of up to 0.21 Ce(IV)/Ce(III). In-situ HERFD-XANES measurements at the Ce L3 edge at up to 800°C were performed to study the cerium oxidation state during the phase transformation from rhabdophane to monazite, revealing an unexpected non-linear behaviour as well as a charge-directing effect of the lanthanum cation.

Fabrication of rare earth (Tb+3) and alkaline earth metal (Mg+2) Co-doped CdAl2O4@MXene composite: A unique approach to tune bandgap energy through quantum confinement effect for photocatalytic applications

The present work includes the use of effective strategy to improve the photocatalytic degradation activity of CdAl2O4 via dopant assimilation to enhance the bandgap energy (Eg) and to influence the light-sensitive activity of this spinel mixed oxide. In this study, CdAl2O4 (CA), Mg–CdAl2O4 (MCA), and Tb-doped Mg–CdAl2O4 (TMCA) were fabricated by the facile co-precipitation route and an ultra-sonication approach was used to prepare a composite of Tb-doped Mg–CdAl2O4 with MXene (TMCA@MXene). The obtained results from UV–Visible analysis deduce that there is an increase in Eg of MCA (2.51 eV) and TMCA (2.67 eV) as compared to pure CA (2.45 eV) which follows the quantum confinement effect accompanying the decrease in crystallite sizes of doped samples as compared to CA. The significant increase in bandgap energy of TMCA is due to the confinement of electrons in a small area and also due to the conversion of continuous energy levels into discrete energy levels. Moreover, UV–Visible spectroscopic analysis was made to evaluate the catalytic performance of fabricated photocatalysts against harmful organic pollutants. The photocatalytic study showed that the co-doped CdAl2O4 (TMCA) is a better photocatalyst than MCA and CA for the degradation of selected pollutants. Among all synthesized catalysts i.e. CA, MCA, TMCA, and TMCA@MXene, the highest photocatalytic activity was shown by MXene based nanocomposite. TMCA@MXene showed ∼86 % degradation of Rhodamine B (RhB) and 79.6 % degradation of Aspirin (acetylsalicylic acid). The outstanding photocatalytic efficacy of TMCA@MXene could be accredited to the quantum confinement effect produced by co-doping of alkaline earth metal (Mg+2) and rare earth metal (Tb+3) and large surface area, high conductivity, and excellent light harvesting capability provided by MXene sheets. Hence, TMCA@MXene could be an effective photocatalyst in future for the removal of toxic organic pollutants.

Fabrication of a novel polyvinylpyrrolidone/chitosan-Schiff base/Fe2O3 nanocomposite for efficient adsorption of Pb(II) and Hg(II) ions from aqueous solution

A novel magnetic polyvinylpyrrolidone/chitosan-Schiff base/Fe2O3 (PVP/CS-SB/Fe2O3) adsorbent was prepared by one-pot facile co-precipitation route for adsorption of Pb(II) and Hg(II) ions from aqueous solution. Fourier transform infrared-spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscope (SEM), vibrating sample magnetometer (VSM) and Brunauer-Emmett-Teller (BET) were used to characterize the synthesized PVP/CS-SB/Fe2O3. The results predicted that the successfully synthesis of magnetic CSSB-PVP@Fe2O3. The effects of important factors such as pH solution, contact time, concentration of metal ions, adsorbent dose and co-existing ions on Pb(II) and Hg(II) adsorption were investigated. The maximum adsorption capacities of Pb(II) and Hg(II) ions at optimal conditions were 120 mg/g and 102.5 mg/g, respectively. The kinetic studies predicted that the adsorption followed the pseudo-second-order (PSO) model as chemisorption using the coordination of active sites of PVP/CS-SB/Fe2O3 with the metal ions and also n-π interactions. Reproducibility results predicted that the excellent regeneration ability after 6 adsorption cycles. According to the results of this work, the PVP/CS-SB/Fe2O3 nanocomposite is promising for Pb(II) and Hg(II) ions adsorption and can be potential as a simple, low-cost, high-efficient adsorbent for decontamination of other heavy metal ions from aqueous solution.

Facile fabrication and electrochemical studies of Bi-Al codoped MoO3 and its composite with r-GO for supercapacitor applications

The primary goal for the development of energy-storage devices is to find affordable ways to increase their efficiency, activity, and stability. In this regard, transition metal oxide mainly MoO3 enhances the electrochemical properties of the material due to various oxidation states. On the other hand, carbonaceous materials, such as reduced graphene oxide, provide a large surface area that increases the conductivity of nanomaterials. In this work, we have synthesized pristine and codoped MoO3 material using the co-precipitation route. While the r-GO based composite was prepared by a simple sonication approach. The prepared composite material showed a higher specific capacitance of 987 F/g than the pristine and codoped material. The BAMO@r-GO discharges after 346 s which was the higher time of discharge than that of pure and codoped material. Moreover, the obtained results from EIS measurement confirmed that the composite material showed less resistance than all other synthesized materials. The synergistic effect between the r-GO and BAMO materials is the reason for the higher supercapacitor performances of BAMO@r-GO. Based on these results, the fabricated BAMO@r-GO material can be effectively utilized as an electrode material in electrochemically powered energy storage devices.

CaCu3Ti4O12 ceramic via oxalate route: Synthesis, characterization and electrical properties

In this manuscript, a new method for the synthesis of CaCu3Ti4O12 (CCTO) perovskite was adopted via co-precipitation followed by calcination processes. The co-precipitation route was employed to synthesize calcium and copper oxalates precipitated on the TiO2 surfaces and the calcination technique at different temperatures was utilized to follow the single-phase formation. Differential thermal analysis-thermogravimetry (DTA-TG) were used to estimate the proper calcination temperatures and to follow the precursor′s decomposition stages. X-ray diffraction (XRD) revealed the initiation of titanate formation at 700 °C. The complete formation of single-phase was achieved at 1100 °C. In agreement with the XRD measurements, FT-IR spectra confirmed the formation the different phases at different calcination temperatures. The prepared titanate showed giant dielectric properties with values higher than reported in literature. The conductivity measurement indicated semi-conducting properties and revealed a transition agreed well with that obtained in the dielectric properties measurements vs. temperature, attributed to the orientional polarization or change in the entire conduction mechanism from hopping to ionic conduction. The obtained electrical properties enhances the utilization of the entire titanate as capacitors.

Natural sunlight energy harvesting using NiAl2O4@N-rGO hetero-junction for photocatalytic degradation of crystal violet dye: Kinetic and mechanistic insights

In this study, NiAl2O4 (NA) was synthesized by the co-precipitation route and its hetero-junctions were fabricated with N-doped reduced graphene oxide (N-rGO) through the ultra-sonication method. The structural, morphological, magnetic, optical and photocatalytic properties of synthesized NA, N-rGO, and the NA@N-rGO 1–4 hetero-junctions characterized by XRD, FTIR, SEM, VSM, PL and UV–visible spectroscopy, respectively. XRD results showed that crystallite size decreases from 25.01 nm (NA) to 15.20 nm for NA@N-rGO-4 and porosity increases up to 77.7 % for NA@N-rGO-4 making it remarkable for photocatalytic applications and FTIR results confirmed the formation of N-rGO as well as its successful integration into NA matrix, resulting in the formation of hetero-junctions. Magnetic properties were investigated using a vibrating sample magnetometer (VSM), revealing distinctive S-shaped hysteresis loops at 25 °C for both NA and N-rGO, as well as the NA@N-rGO 1–4 hetero-junctions and magnetic saturation decreases with an increase in N-rGO content as for NA@N-rGO-4 Ms drops to 0.0038 emu/g. Notably, the bandgap of NA@N-rGO-4 hetero-junction was effectively reduced from 3.0 eV (in the case of NA) to 2.1 eV, resulting in a discernible decrease in photoluminescence (PL) intensity and increase in e--h+ pair separation. Under visible light, NA@N-rGO-4 exhibited a remarkable 94.68 % efficiency in crystal violet (CV) dye degradation within just 90 min, outperforming NA's 59.05 % degradation efficiency and OH. Radicals play a major contribution to the degradation of dye. The optimization of degradation capabilities was achieved through the manipulation of catalyst dosage, dye concentration and varying pH values for the degradation of CV dye. NA@N-rGO-4 hetero-junction demonstrates the considerable potential for efficient dye degradation in wastewater under visible light, owing to its exceptional catalytic performance.

Enhanced electrophoretic deposition of hydrophobic BiVO4 photocatalytic coatings using Cu2+ ions as stabilizing agent

In this work, we report the preparation of monoclinic bismuth vanadate (BiVO4) coatings through an electrophoretic deposition process (EPD) using Cu2+ ions as a charge-stabilizing agent. BiVO4 was prepared through a rapid coprecipitation route, yielding rounded nanoparticles with sizes smaller than 100 nm. The bismuth vanadate nanoparticles were dispersed in isopropyl alcohol for electrophoretic deposition onto aluminum plates using a constant applied voltage of 12 V for 30 min. The results have shown that the deposited amount of BiVO4 nanoparticles increases with the initial concentration of the Cu(NO3)2⋅5H2O additive. According to XPS analysis, EPD coatings exhibit the presence of metallic copper due to the reduction of Cu2+ ions on the BiVO4 during the electrophoretic deposition process. The photocatalytic properties of BiVO4 coatings were assessed in the degradation of the antibiotic tetracycline under simulated solar irradiation. The BiVO4 coating prepared with an initial concentration of 0.5 mM of Cu(NO3)2⋅5H2O exhibited the highest photocatalytic performance, achieving a degradation efficiency of approximately 92 % after 240 min of irradiation. Furthermore, the BiVO4 coatings displayed superhydrophobic properties, as determined by measuring static water contact angles.

Development and understanding of the lithiation/de-lithiation mechanism of a low cobalt and nickel-rich cathode material for lithium‐ion batteries

Nickel-rich LiNixMnyCo1−x−yO2 (NMC, with x ≥ 0.6) layered oxides are regarded as cathode candidates for high-energy density lithium-ion batteries (LIBs). However, this technology faces several challenges due to the scarcity of crucial raw materials such as cobalt precursors and the negative environmental impact of their extraction process. It is therefore, it becomes imperative to develop low cobalt content cathode compositions that offer alternative options with comparable electrochemical performance. Herein, we have used a systematic approach to modify the composition while keeping all other properties (particle size and morphology) constant to synthesise low-Co-cathode materials, namely LiNi0·8Mn0·1Co0·1O2 (NMC-10 %) and LiNi0·8Mn0·15Co0·05O2 (NMC-5%). A co-precipitation route using a continuous stirred thank reactor was used for synthesis. The physico-chemical properties, electrochemical performances, cycling stability, and rate capabilities of NMC-5% materials are comparable to those of NCM-10 % materials. NMC-10 % and NMC-5% half cells show initial specific discharge capacities of 191 mAh.g−1, and 185 mAh.g−1, respectively, in a voltage range of 2.8–4.3 V (vs. Li+/Li). The NMC-5% exhibits excellent thermal stability, characterized by a predominant exothermic peak at 432 °C and significantly lower total heat energy when compared to NMC-10 % counterpart, which displayed its main exothermic peak at 339 °C. The structural and electronic changes of both materials were evaluated through in operando synchrotron-based X-ray techniques. Regardless of the cobalt content, both materials show comparable structural and electronic evolution upon the de-intercalation/intercalation of Li+ ions. An irreversible phase transition at the first delithiation was observed as emphasized by diffraction of synchrotron radiations.

Efficient Catalytic Synthesis of Glycerol Carbonate Using Optimized Na and K Titanate Nanotubes Catalysts

The synthesis of glycerol carbonate from glycerol has garnered significant research attention because of its wide application in the lithium-ion battery and pharmaceutical industries. This study summarizes the catalytic transformation of glycerol to glycerol carbonate using Na and K titanate nanotubes as catalysts. We report the synthesis of Na and K titanate nanotubes catalyst by a simple co-precipitation route and investigate their catalytic activity in the transesterification of glycerol. The physicochemical properties of the Na and K titanate nanotubes catalyst were successfully studied by CO2-TPD and XRD. The designed catalyst possesses high catalytic efficiency and stability in the transesterification reaction of glycerol. Based on its surface area and basicity, several experiments were performed, and it was observed that under optimized conditions (i.e., 5 wt.% catalyst loading, 5:1 molar ratio of DMC to glycerol, 90 °C, and 90 min), the highest conversion of glycerol was achieved, 92.6% glycerol carbonate. The high thermal stability and recyclability make it an efficient heterogeneous catalyst for the synthesis of glycerol carbonate.

Simultaneous Environmental Waste Management through Deep Dewatering of Alum Sludge Using Waste-Derived Cellulose

To simultaneously solve problems in an eco-friendly manner, introducing a waste residual as a sustainable conditioner to aid alum sludge dewatering is suggested as a cradle-to-cradle form of waste management. In this regard, the superiority of deep dewatering alum sludge with a powdered wood chip composite residual as a novel conditioner was explored, whereby traditional conventional conditioners, i.e., polyelectrolytes and lime, were substituted with powdered wood chips. Initially, Fe3O4 was prepared at the nanoscale using a simple co-precipitation route. Next, wooden waste was chemically and thermally treated to attain cellulosic fine powder. Subsequently, the resultant wood powder and Fe3O4 nanoparticles were mixed at 50 wt % to attain a wood powder augmented with iron, and this conditioner was labeled nano-iron-cellulose (nIC-Conditioner). This material (nIC-Conditioner) was mixed with hydrogen peroxide to represent a dual oxidation and skeleton builder conditioning substance. Characterization of the resultant conditioner was carried out using transmission electron microscopy (TEM) and Fourier transform infrared (FT-IR) transmittance spectrum analysis. The feasibility of the experimental results revealed that the moisture content in the sludge cake was lower after conditioning, and the capillary suction time (CST) was reduced to 78% compared to that of raw alum sludge after 5 min of dewatering time. Moreover, the optimal system parameters, including nIC-Conditioner and H2O2 concentrations, as well as the working pH, were optimized, and optimal values were recorded at 1 g/L and 200 mg/L for nIC-Conditioner and H2O2, respectively, with a pH of 6.5. Additionally, scanning electron microscope (SEM) analyses of the sludge prior to and after conditioning were conducted to verify the change in sludge molecules due to this conditioning technique. The results of this study confirm the sustainability of an alum sludge and waste management facility.

Optical and electrochemical properties of manganese oxide (Mn3O4) nanoparticles: Investigating the influence of calcination temperature on supercapacitor performance

In this study, we investigate the influence of calcination temperature on the structural, optical, and electrochemical properties of Mn3O4 nanoparticles synthesized through a chemical co-precipitation route. Field-Emission Scanning Electron Microscopy (FESEM) images depict the formation of highly agglomerated, spherical-shaped particles. At calcination temperatures of 700 °C and 900 °C, the observation reveals the emergence of flat pellets and rod-like structures. The X-ray Diffraction (XRD) patterns confirm the presence of the Mn3O4 phase in M0 and M1 samples. However, the sample calcined at 500 °C (M3) showed a mixed phase of Mn3O4 and Mn2O3. Upon further calcination at 700 and 900 °C, this mixed phase undergoes complete transformation into the Mn2O3 phase. The change in absorption onset and photoluminescence intensity of samples is found with an increase in calcination temperature due to the crystal growth and phase modification. Furthermore, the synthesized samples are employed as electrode materials for supercapacitor applications. The sample calcined at 300 °C (M1) in three-electrode system demonstrated the specific capacitance (Csp) of 273.3 F/g at 0.5 A/g in an alkaline medium. The asymmetric cell assembled by using M1 and Hibiscus cannabinus stem-derived carbon material (HBC-900) delivered higher Csp of 205.7 F/g at 0.5 A/g. In addition, asymmetric supercapacitor device exhibited a high energy and power density of 43.1 Wh/kg and 476.2 W/kg with 82.07 % of initial Csp retention over 10,000 cycles at 10 A/g, which makes the sample M1 as the potential electrode material for supercapacitor application.

Structural and magnetic behaviour of temperature influenced Mn0.5Zn0.25Cu0.25Fe2O4 spinel nanoparticles by co-precipitation route

Structural and magnetic behaviour of temperature influenced Mn0.5Zn0.25Cu0.25Fe2O4 spinel nanoparticles by co-precipitation route

Application of cobalt-cerium-iron ternary layered double hydroxide for extraction of perfluorooctane sulfonate followed by HPLC-MS/MS analysis

Herein, Ce-doped CoFe layered double hydroxide (LDH), noted as CoCeFe ternary LDH, was prepared using the co-precipitation route. Prosperous synthesis of CoFe LDH and successful partial replacement of iron cations with cerium cations in CoCeFe ternary LDH were confirmed by X-ray diffraction patterns, energy-dispersive X-ray spectroscopy, and elemental dot-mapping images. Nanosheet morphology was recognized for both CoFe LDH and CoCeFe ternary LDH from scanning electron microscopy and transmission electron microscopy micrographs. In the following, a dispersive solid phase extraction (DSPE) method was developed using the synthesized CoCeFe ternary LDH as a sorbent for extracting perfluorooctanesulfonic acid (PFOS) from wastewater samples. For the selective analysis of PFOS, high-performance liquid chromatography-tandem mass spectroscopy (HPLC-MS/MS) in multiple reaction monitoring mode was used. Analytical parameters such as the limit of detection equal to 0.02 μg/L, with a linear range of 0.05–300 μg/L, the limit of quantification equal to 0.05 μg/L, and an enrichment factor equal to 23.3 were achieved for PFOS at the optimized condition (sorbent: 5 mg of CoCeFe ternary LDH, eluent type and volume: 150 μL mobile phase, pH: 3, adsorption time: 3 min, and desorption time: 5 min). The developed strategy for the analysis of PFOS was tested in real wastewater samples, including copper mine and petrochemical wastewater. The amount of analytes in real samples was calculated using the standard addition method, and good relative recovery in the range of 86%–105% was obtained. The main novelty of this research is the application of CoCeFe ternary LDH to extract the PFOS from wastewater using the DSPE method for determination by HPLC-MS/MS.

Effect of surfactants on the electrochemical performance of iron hexacyanoferrate prepared by co-precipitation route for aqueous potassium-ion storage

Effect of surfactants on the electrochemical performance of iron hexacyanoferrate prepared by co-precipitation route for aqueous potassium-ion storage

Thermal Energy Storage Using Hybrid Nanofluid Phase Change Material (PCM) Based on Waste Sludge Incorp Rated ZnO/α-Fe2O3.

Renewable solar energy storage facilities are attracting scientists' attention since they can overcome the key issues affecting the shortage of energy. A nanofluid phase change material (PCM) is introduced as a new sort of PCM is settled by suspending small proportions of nanoparticles in melting paraffin. ZnO/α-Fe2O3 nanocrystals were prepared by a simple co-precipitation route and ultrasonically dispersed in the paraffin to be a nanofluid-PCM. The behaviors of the ZnO/α-Fe2O3 nanocrystals were verified by X-ray diffraction (XRD) analysis, and the average particle size and the morphology of the nanoparticles were explored by transmission electron microscopy (TEM). For the object of industrial ecology concept, aluminum-based waste derived from water-works plants alum sludge (AS) is dried and augmented with the ZnO/α-Fe2O3 nanocrystals as a source of multimetals such as aluminum to the composite, and it is named AS-ZnO/α-Fe2O3. The melting and freezing cycles were checked to evaluate the PCM at different weight proportions of AS-ZnO/α-Fe2O3 nanocrystals, which confirmed that their presence enhanced the heat transfer rate of paraffin. The nanofluids with AS-ZnO/α-Fe2O3 nanoparticles revealed good stability in melting paraffin. Additionally, the melting and freezing cycles of nanofluid-PCM (PCM- ZnO/α-Fe2O3 nanoparticles) were significantly superior upon supplementing ZnO/α-Fe2O3 nanoparticles. Nanofluid-PCM contained the AS-ZnO/α-Fe2O3 nanocrystals in the range of 0.25, 0.5, 1.0, and 1.5 wt%. The results showed that 1.0 wt% AS-ZnO/α-Fe2O3 nanocrystals contained in the nanofluid-PCM could enhance the performance with 93% with a heat gained reached 47 kJ.

Dry reforming of methane over Ni–Mg–Al and Ni–Ca–Al type hydrotalcite-like catalysts: effects of synthesis route and Ru incorporation

Abstract Ni-incorporated Mg–Al type hydrotalcite-like catalytic materials were synthesized following impregnation and co-precipitation routes, and their catalytic performances were compared in the dry-reforming reaction of methane. The effects of Ru impregnation on the catalytic performance of Ni-incorporated Mg–Al were also investigated. Results showed that the catalytic performance of the Ni-incorporated Mg–Al type catalyst (NiMgAlO), which was prepared by the co-precipitation route, was highly stable during dry-reforming reaction tests performed at 600 °C, extending up to 24 h. The fractional conversion of CO2 (0.42) was higher than the fractional conversion of CH4 (0.29) due to the contribution of the reverse water gas shift reaction. However, the contribution of the reverse water gas shift reaction to the product distribution was much less with the catalyst prepared following the impregnation route (Ni@MgAlO). This difference was shown to be mainly due to the state of the nickel in the catalyst structures. Ni-impregnated Ca–Al type hydrotalcite-like catalyst (Ni@CaAlO) was also synthesized and tested in dry reforming of methane. Results obtained with the Ni-impregnated Ca–Al type catalyst showed some changes in its structure and the formation of some CaCO3 during the dry reforming reaction. The comparison of the performances of Ni-impregnated Mg–Al and Ca–Al type catalysts showed a higher amount of coke on the surface of Ni@CaAlO than Ni@MgAlO. It was also concluded that significant coke minimization and highly stable catalytic performance could be achieved by the impregnation of 1 % Ru to the NiMgAlO catalyst. The amount of coke deposited on the catalyst decreased from about 30 % to less than 5 %, by Ru impregnation. The decrease of the surface area of the Ru-impregnated catalyst was also only about 3 % after 240 min of reaction time.

Antimony-doped cerium ferrite: a robust photocatalyst for the mitigation of diclofenac potassium, an emerging contaminant

The present work reports an improvement in the photocatalytic performance of cerium ferrite (CeFeO3) via doping of antimony (Sb) towards the photodegradation of toxic pharmaceutical pollutant i.e. diclofenac potassium. The variable concentrations of Ce1-xSbxFeO3 (x = 0.00, 0.01, 0.03, 0.05, 0.06, 0.07, 0.09) were prepared using facile co-precipitation route and subsequently characterized for their optical, structural, morphological, and dielectric properties using various analytical techniques. It was established that an increase in Sb concentration as dopant (up to x = 0.07) reduced the optical band gap from 2.74 eV to 2.42 eV making it suitable candidate for photodegradation. The X-ray diffraction (XRD) pattern revealed orthorhombic phase of synthesized materials with small crystallite sizes in the range of 15.28 to 2.42 nm. The high value of dielectric constant (3.5841 × 106) for Ce0.93Sb0.07FeO3 with small loss tan (3.1208) compared with the CeFeO3 indicated its ability as photocatalyst to effectively store charges to make them utilize for photocatalytic activity. The degradation efficiency of Ce0.93Sb0.07FeO3 reached 86.7% in 120 min of light irradiation under optimized conditions (pH = 4, catalyst dosage = 15 mg, primary drug concentration = 5 mg/L). Ce0.93Sb0.07FeO3 was also found to be stable over its multiple catalytic runs as only 6.5% decline in degradation efficiency was observed in recyclability test. The remarkable performance of antimony doped cerium ferrite against the removal of persistent pharmaceutical pollutant indicated its strong potential to be used in wastewater treatment in future works.

Tuning The physicochemical Properties of CeO2 Nanoparticles for Enhanced Photocatalytic and Anticancer Performance by Zn Doping

Semiconductor nanoparticles (NPs) have attracted considerable attention owing to their potential applications, such as optoelectronic devices, environmental remediation, energy conversion, and biomedical. This work was designed to tailor the physicochemical properties of CeO2 NPs by Zn doping at different concentrations (0 ≤ x ≤ 0.03) to improve their photocatalytic and anticancer performance. The modified co-precipitation route was fruitfully applied to prepare ZnxCe1-xO2 NPs (with 0 ≤ x ≤ 0.03). Different characterization facilities like XRD, TEM, SEM, EDX, FTIR, and PL spectroscopy have been employed to examine the properties of these prepared NPs. XRD data revealed that the crystallite of NPs was changed after Zn doping with the decrease of its crystal sizes. TEM and SEM imaging discovered that the NPs were further sphere-shaped with homogenous distribution. Moreover, SEM elemental mapping with EDX confirmed that the elements (Ce, O, and Zn) in prepared NPs have uniform distribution and chemical composition in prepared Zn0·03Ce0·97O2 NPs. FTIR results determined the functional groups in the prepared NPs. PL spectra observed a decrease in the recombination of electron (e−)-hole (h+) pair with increasing Zn doping due to a change in bandgap energy. Photocatalytic data indicates that the photodegradation efficiency (D) of Rh B dye of Zn0·03Ce0·97O2NPs(75.5%) under UV light during 100 min was greater than pure CeO2 NPs. Cytotoxicity analysis showed that the anticancer effect of CeO2 NPs against human liver cancer (HepG2) increases with the addition of Zn ions. Additionally, these results indicated that the addition of Zn ions to CeO2 NPs plays a role in killing cancer cells at higher concentrations. This study recommended that these NPs could be applied to potential applications in environmental pollution and cancer therapy in vivo studies.