Protein Chromatography Research Articles

UV absorption‐based inverse modeling of protein chromatography

UV absorbance measurements play an important role in bioprocess development. Yield and purity are often evaluated in terms of peak percentages in analytical SEC or ion‐exchange chromatography. Also, industrial chromatography steps are usually controlled based on UV data with pooling decisions according to absorbance thresholds. Model‐based process development would make elaborate screening experiments redundant, once the model has been calibrated to the specific process step. So far, absorbance measurements could not be used directly for modeling chromatography steps as the commonly applied models rely on mass or molar concentration. This study presents mechanistic modeling of an industrially relevant chromatography setting without any knowledge of the feed composition. The model equations were rewritten to employ boundary conditions in UV absorbance units, the absorption coefficients were shifted into the isotherm, and standard parameter estimation procedures could be applied. An anion‐exchange chromatography case study of a target protein expressed in Escherichia coli and 11 lumped impurity peaks demonstrated practical applicability. The target protein concentration in the feed material was estimated from chromatograms. Using this method, initially unknown feed concentrations can be determined a posteriori for ion‐exchange and multimodal chromatography from single‐component absorbance curves.

Protein adsorption and chromatography on novel mixed-mode resins fabricated from butyl-modified poly(ethylenimine)-grafted Sepharose

We have previously studied benzoyl-modified poly(ethylenimine) (PEI)-grafted Sepharose FF resins for mixed-mode chromatography (MMC), and found PEI-grafted resin with an ionic capacity (IC) of about 300mmol/L was suitable for fabricating MMC resins to achieve favorable MMC performance. To extend the application of PEI-grafted resins in MMC, we have herein modified a PEI-grafted resin with an initial IC of 315mmol/L (FF-PEI-L315) with hydrophobic butyl groups, and two MMC resins with residual ICs of 280 and 252mmol/L were obtained (denoted as Bu30-PEI315 and Bu60-PEI315). Bovine serum albumin (BSA) and γ-globulin adsorption at pH 8.0 and elution at pH 3.0 were first explored on the two MMC resins. It was found that with increasing butyl density, protein binding capacity increased but the elution percentage decreased, indicating that high butyl density was beneficial in protein adsorption but not favorable in elution. It was considered that the butyl density of Bu60-PEI315 was so high that the electrostatic repulsion at pH 3.0 was insufficient to make the protein dissociate from the resin surface. Then, the eluent was switched to 3-[(3-cholamido-propyl)-dimethylammonio]-1-propanesulfonate (CHAPS) solution, and complete BSA recovery was obtained on Bu60-PEI315. Complete γ-globulin recovery was obtained on Bu60-PEI315 at a lower CHAPS concentration than that for BSA. This suggests the possibility of selective elution of the two proteins by manipulating eluent concentration. The results indicate that CHAPS was a suitable eluent for protein recovery and separation with the MMC resin, particularly for the purification of antibody from feedstock containing serum albumin. Finally, adsorption equilibria and uptake kinetics onto Bu30-PEI315 and Bu60-PEI315 were investigated. At 0mol/L NaCl, BSA binding on the MMC resins was only by electrostatic interaction while γ-globulin showed a bi-modal binding behavior, including electrostatic and hydrophobic interactions. At high NaCl concentrations, both BSA and γ-globulin were bound by hydrophobic interaction. Favorable binding properties for different proteins in a wide range of NaCl concentrations were observed on Bu60-PEI315, indicating its usefulness as an MMC adsorbent.

Comparative study of low-energy ultrasonic and alkaline treatment on biosludge from secondary industrial wastewater treatment

In this study, low-energy ultrasonic (3 and 6 kJ/g volatile solids of feed biomass (FB) which was lower than the heat value of the FB), alkaline, and ultrasonic–alkaline pretreatments were applied on FB, a biosludge from secondary industrial wastewater treatment. Biochemical methane potential (BMP), particle size distribution, Biomass Stress Index (BSI™), soluble chemical oxygen demand (SCOD), protein, carbohydrate, and size-exclusion chromatography (SEC) fingerprints were used to comparatively study the mechanisms of these pretreatment methods. The results indicated that low-energy ultrasonication and alkali exhibited significantly different impacts on the FB. After ultrasonication with energy input of 6 kJ/g-VS, the average particle size of FB was reduced from 102.6 to 19.4 µm. However, ultrasonication had no obvious effect on microbial cells rupture, solubilization of protein and carbohydrate, and SEC fingerprint. Consequently, low-energy ultrasonication could not enhance methane generation. However, after alkaline pretreatment with dosage of 0.3 g-NaOH/g-VS, SCOD, soluble protein, and soluble carbohydrate concentration of FB increased from 0.66, 0.00, 0.07 to 2.83, 0.83, 0.47 g/L, respectively. At the same time, BSI™ increased from 5.3% to 96.8%, and the SEC fingerprint changed significantly. Consequently, the methane generation in the BMP test increased from 68.9 to 135.0 mL. Ultrasonic–alkaline pretreatment was similar to alkaline pretreatment in terms of methane generation. Based on this study, alkaline pretreatment is recommended over both low-energy ultrasonic and low-energy ultrasonic–alkaline pretreatment to enhance the biodegradability of FB.

Riboflavin Binding Protein and Riboflavin Transport to Hen Eggs as an Educational Tool

Riboflavin Binding Protein (RBP) is a stable glycophosphoprotein abundant in the eggs of many oviparous species, including chickens. The function of the protein is to transfer riboflavin (Rf) to the developing embryo, and recent evidence suggests it also binds copper. Because of its bright yellow color and fluorescence, Rf transport serves as an excellent model system. A natural mutant strain of white leghorn chickens, containing a site mutation, is unable to synthesize RBP and thus the eggs are devoid of Riboflavin. We are currently investigating the protein and mutant egg use for both an undergraduate biochemistry lab (1) as well as an outreach project for K-12 students (2). The undergraduate research-style experiment for advanced biochemistry lab students is a useful exercise in learning protein purification techniques, including dialysis, salt precipitation and chromatography. Because of the holoRBP yellow color, it is easy to follow, and its stability renders it possible to carry out steps over time at room temperature. We have modified a standard procedure and students have successfully purified protein. Using the mutant and regular chicken eggs we have modified an education series as an informative and didactic approach towards problem-based learning. Our main motive was to perform outreach to K-12 with an interactive experiment featuring the importance of vitamins and the mechanisms of molecular transport.

Displacement chromatography of proteins using a retained pH front in a hydrophobic charge induction chromatography column

The chromatographic separation of two proteins into a displacement train of two adjoined rectangular bands was accomplished using a novel method for hydrophobic charge induction chromatography (HCIC) which employs a self-sharpening pH front as the displacer. This method exploits the fact that protein elution in HCIC is promoted by a pH change, but is relatively independent of salt effects, so that a retained pH front can be used in place of a traditional displacer in displacement chromatography. The retained pH front was produced using the two adsorbed buffering species tricine and acetic acid. The separation of lysozyme and α-chymotrypsinogen A into adjoined, rectangular bands was accomplished with overall recoveries based on the total mass injected greater than 90 and 70%, respectively. The addition of urea to the buffer system increased the sharpness of the pH front by 36% while the yields of lysozyme and α-chymotrypsinogen A based on the total mass eluted increased from 76% to 99% and from 37% to 85%, respectively, when the purities of both proteins in their product fractions were fixed at 85%. The results demonstrate that the method developed in this study is a useful variant of HCIC and is also a useful alternative to other displacement chromatography methods.

Strong cation-exchange chromatography of proteins on a sulfoalkylated monolithic cryogel

A new strong cation exchanger (SCX) monolithic column was synthesized by at-line surface modification of a cryogel prepared by copolymerization of 2-hydroxyethylmethacrylate (HEMA) and glycidylmethacrylate (GMA). Sodium salt of 3-Mercaptopropane sulfonic acid (3-MPS) was used as the ligand to transform the surface of the monolith into a strong cation exchanger. The obtained material was characterized in terms of elemental analysis, infrared spectroscopy (FTIR), Scanning Electron Microscopy (SEM), Brunauer–Emmett–Teller (BET) N2 adsorption, and used as a stationary phase for strong-cation exchange chromatography of some proteins, such as α-chymotrypsinogen, cytochrome c and lysozyme. Water permeability of the column was calculated according to Darcy's law (2.66×10−13m2). The performance of the monolithic cryogel column was evaluated on the basis of Height Equivalent to a Theoretical Plate (HETP). Retention behavior of the studied proteins was modeled on the basis of Yamamoto model to understand the role of the ion-exchange mechanism in retention behaviors. The considered proteins were successfully separated, and the obtained chromatogram was compared with that obtained with a non-functionalized cryogel column.

Overcoming solubility limits in overloaded gradient hydrophobic interaction chromatography

The impact of the solubility limits on the performance of gradient protein chromatography has been studied. As a case study elution of model protein, i.e., lysozyme, on hydrophobic interaction media has been selected. A dependence of the protein solubility and crystallization kinetics on the content of cosmotropic salt in the mobile phase has been determined. Moreover, adsorption properties of the protein versus the mobile phase composition have been quantified. A model of chromatographic column dynamics has been developed which incorporated the mass transport kinetics accompanying both adsorption and crystallization processes. The model was used to study the influence of operating parameters such as flowrate and concentration loading on the solubility pattern inside the column and the separation performance. The analysis performed indicated existence of supersaturation regions for which, due to slow kinetics of crystallization, chromatographic process could be performed under conditions of strong concentration overloading while avoiding undesirable effects of flow blockage in chromatographic systems.

Combined effects of potassium chloride and ethanol as mobile phase modulators on hydrophobic interaction and reversed-phase chromatography of three insulin variants

The two main chromatographic modes based on hydrophobicity, hydrophobic interaction chromatography (HIC) and reversed-phase chromatography (RPC), are widely used for both analytical and preparative chromatography of proteins in the pharmaceutical industry. Despite the extensive application of these separation methods, and the vast amount of studies performed on HIC and RPC over the decades, the underlying phenomena remain elusive. As part of a systematic study of the influence of mobile phase modulators in hydrophobicity-based chromatography, we have investigated the effects of both KCl and ethanol on the retention of three insulin variants on two HIC adsorbents and two RPC adsorbents. The focus was on the linear adsorption range, separating the modulator effects from the capacity effects, but some complementary experiments at higher load were included to further investigate observed phenomena. The results show that the modulators have the same effect on the two RPC adsorbents in the linear range, indicating that the modulator concentration only affects the activity of the solute in the mobile phase, and not that of the solute–ligand complex, or that of the ligand. Unfortunately, the HIC adsorbents did not show the same behavior. However, the insulin variants displayed a strong tendency toward self-association on both HIC adsorbents; on one in particular. Since this causes peak fronting, the retention is affected, and this could probably explain the lack of congruity. This conclusion was supported by the results from the non-linear range experiments which were indicative of double-layer adsorption on the HIC adsorbents, while the RPC adsorbents gave the anticipated increased tailing at higher load.

Preparation of a poly(3'-azido-3'-deoxythymidine-co-propargyl methacrylate-co-pentaerythritol triacrylate) monolithic column by in situ polymerization and a click reaction for capillary liquid chromatography of small molecules and proteins.

Combining free radical polymerization with click chemistry via a copper-mediated azide/alkyne cycloaddition (CuAAC) reaction in a "one-pot" process, a facile approach was developed for the preparation of a poly(3'-azido-3'-deoxythymidine-co-propargyl methacrylate-co-pentaerythritol triacrylate) (AZT-co-PMA-co-PETA) monolithic column. The resulting poly(AZT-co-PMA-co-PETA) monolith showed a relatively homogeneous monolithic structure, good permeability and mechanical stability. Different ratios of monomers and porogens were used for optimizing the properties of a monolithic column. A series of alkylbenzenes, amides, anilines, and benzoic acids were used to evaluate the chromatographic properties of the polymer monolith in terms of hydrophobic, hydrophilic and cation-exchange interactions, and the results showed that the poly(AZT-co-PMA-co-PETA) monolith exhibited more flexible adjustment in chromatographic selectivity than that of the parent poly(PMA-co-PETA) and AZT-modified poly(PMA-co-PETA) monoliths. Column efficiencies for toluene, DMF, and formamide with 35,000-48,000 theoretical plates per m could be obtained at a linear velocity of 0.17 mm s(-1). The run-to-run, column-to-column, and batch-to-batch repeatabilities of the retention factors were less than 4.2%. In addition, the proposed monolith was also applied to efficient separation of sulfonamides, nucleobases and nucleosides, anesthetics and proteins for demonstrating its potential.

The influence of gibberellin on the level of soluble protein and activities of some hydrolases in corn seedlings

The effect of gibberellin on the qualitative and quantitative composition of soluble proteins and the activity of Mg<sup>++</sup> dependent and Na<sup>+</sup>-K<sup>+</sup> -stimulated ATPase, RNase and peptidase in five days old maize seedlings were investigated. The chromatography of soluble proteins on DEAE cellulose gave seven fractions. All these fractions had ATPase and RNase activities. Gibberellin stimulated most strongly ATPase, to a smaller degree RNase and it did not effect the activity of peptidase.

Evaluation of synthesized lipid tethered ligands for surface functionalization of polypropylene capillary-channeled polymer fiber stationary phases

Polypropylene (PP) capillary-channeled polymer (C-CP) fibers have been used in this laboratory as stationary phases for high performance liquid chromatography and solid phase extraction of proteins. Greater selectivity has been realized through the functionalization of the PP fibers through the physical adsorption of commercially available head group-modified poly(ethylene glycol) lipids (PEG-lipids), where the head group is chosen to affect affinity separations. We refer to this general surface modification methodology as lipid tethered ligands (LTLs). In this study, LTLs were synthesized by solid phase synthesis. In comparison to the commercial PEG-lipids, the synthesized LTLs contain no chemically labile phosphate groups. Instead of an ester linkage in the commercial lipids, amide functionality was used in the synthesized LTLs to attach the lipids and ligands. By use of fluorescence imaging of FITC-labeled LTLs, the synthesized LTL was shown to be superior to the commercial LTL in terms of the adsorption efficiency to PP C-CP fibers, the resistance to solvent wash from the PP C-CP fibers, and their chemical stability under acidic, neutral and basic conditions. The PP C-CP fibers functionalized with a synthesized LTL that was biotinylated at the head group are shown to be capable of capturing streptavidin from E. coli cell lysate more efficiently than the PP C-CP fibers functionalized with the commercial biotinylated PEG-lipid. The functionalization of PP C-CP fibers with the synthesized LTLs is a simple, but highly efficient, method to generate novel stationary phases with a variety of functionalities for solid phase extraction and liquid chromatography.

Equilibrium adsorption of hexahistidine on pH-responsive hydrogel nanofilms.

We present a molecular theory to study the adsorption of different species within pH-sensitive hydrogel nanofilms. The theoretical framework allows for a molecular-level description of all the components of the system, and it explicitly accounts for the acid-base equilibrium. We concentrate on the adsorption of hexahistidine, one of the most widely used tags in bio-related systems, particularly in chromatography of proteins. The adsorption of hexahistidine within a grafted polyacid hydrogel film shows a nonmonotonic dependence on the solution pH. Depending on the salt concentration, the density of the polymer network, and the bulk concentration of peptide, substantial adsorption is predicted in the intermediate pH range where both the network and the amino acids are charged. To enhance the electrostatic attractions, the acid-base equilibrium of adsorbed hexahistidine is shifted significantly, increasing the degree of charge of the residues as compared to the bulk solution. Such a shift depends critically on the conditions of the environment at the nanoscale. At the same time, the degree of dissociation of the network becomes that of the isolated acid group in a dilute solution, which means that the network is considerably more charged than when there is no adsorbate molecules. This work provides fundamental information on the physical chemistry behind the adsorption behavior and the response of the hydrogel film. This information can be useful in designing new materials for the purification or separation/immobilization of histidine-tagged proteins.

Biotin-functionalized poly(ethylene terephthalate) capillary-channeled polymer fibers as HPLC stationary phase for affinity chromatography.

Native poly(ethylene terephthalate) (PET) capillary-channeled polymer (C-CP) fibers have been used as the stationary phase for high-performance liquid chromatography (HPLC) of proteins via reversed-phase and ion-exchange processes. Functionalization can be used to bring about greater selectivity through surface modification. PET fibers were treated with ethylenediamine to generate primary amine groups on the fiber surface, enabling subsequent covalent attachment of ligands. The ninhydrin test for primary amines revealed surface densities of 13.9-60.0 μmol m(-2) for PET fibers exposed for periods of 3-12 min. Here, 8-amino-3,6-dioxaoctanoic acid was linked to the EDA-treated PET fiber surface as a hydrophilic spacer, and then D-biotin was attached on the end of the spacer as an affinity ligand. The streptavidin binding capacity and binding homogeneity were studied on the biotin-functionalized PET C-CP fiber microbore column. The selectivity of the biotin surface functionalization was assessed by spiking lysate with Texas Red-labeled streptavidin and enhanced green fluorescent protein. Greater than 99% selectivity was realized. This ligand-coupling strategy from standard solid-phase peptide synthesis used in stationary phase functionalization creates great potential for PET C-CP fiber-packed HPLC columns to perform a variety of chromatographic separations.

Poly(4-vinylpyridine): a polymeric ligand for mixed-mode protein chromatography

Poly(4-vinylpyridine) (P4VP) was proposed for use as a polymeric ligand of mixed-mode chromatography (MMC) of proteins. P4VP has linear hydrophobic chains with ionizable pyridyl groups in its backbone. The polymer was coupled onto Sepharose FF gel at a pyridyl group density of 190μmol/mL (FF-P4VP-190) by the substitution reaction of pyridyl amines with brominated Sepharose gel. Thereby the immobilized ligand possesses the intrinsic hydrophobic nature as well as the newly obtained electrostatic interaction properties endowed from the substituted positively charged pyridyl amines. The pore size distribution was measured by inverse size exclusion chromatography, and the results revealed that P4VP formed a three-dimensional layer on the matrix surface with a maximum layer depth of 4.2nm. The adsorption isotherms of γ-globulin and bovine serum albumin (BSA) to FF-P4VP-190 were determined under varying pH values and salt concentrations to provide insights into the adsorption properties of the medium. It was found that the adsorption capacity of γ-globulin and BSA both presented an increase with pH increasing from 8.0 to 9.0. Moreover, FF-P4VP-190 exhibited stronger adsorption for BSA than γ-globulin. The higher affinity for BSA might be attributed to its more net negative charges. Protein adsorption capacities to FF-P4VP-190 decreased with increasing NaCl concentration, but still manifested moderate levels at high salt concentration such as 75mg/mL for γ-globulin and 14mg/mL for BSA at 0.5mol/L NaCl and pH 9.0. The capacity decreases with increasing ionic strength, indicating the dominant role of electrostatic interactions, while the moderate capacity values at 0.5mol/L NaCl confirmed the presence of salt-tolerant feature of FF-P4VP-190, making it function as an MMC material. Column chromatography was conducted to investigate protein elution behavior. Efficient protein recovery was achieved at mild elution conditions such as pH 4.0 for γ-globulin and pH 4.5 for BSA. The results indicate that the P4VP-based adsorbent would provide new possibilities for protein purification by MMC.

Roles of interstitial fraction and load conditions on the dynamic binding capacity of proteins on capillary-channeled polymer fiber columns.

Capillary-channeled polymer (C-CP) fibers are used as a stationary phase for ion-exchange chromatography of proteins. Collinear packing of the fibers permits operation at high linear velocities (Uo > 100 mm s(-1)) and low backpressure (<2,000 psi) on analytical-scale columns. Rapid solvent transport is matched with very efficient solute mass transfer as fibers are virtually non-porous with respect to the size of the target protein molecules. Lack of porosity of course limits the equilibrium binding capacity of stationary phases. Breakthrough curves and frontal analysis are used to better understand trade-offs between the kinetic and thermodynamic properties as C-CP fibers are applied in preparative situations. Fiber columns packed to different interstitial fraction values affect both the total fiber surface area (e.g., equilibrium binding capacity [EBC]) and the permittivity to flow and mass transport characteristics (e.g., dynamic binding capacity [DBC]). The EBC of the nylon 6 C-CP fibers was found to be 1.30 mg g(-1), with isotherms that were best matched by a Moreau model, showing linearity up to solute concentrations of ∼0.4 mg mL(-1). Isotherms generated under flow conditions were equally well approximated using Langmuir, Freundlich, and Moreau isotherm models. Fairly linear responses were seen up to the maximum load concentration of 1.2 mg mL(-1). Counterintuitively, dynamic studies revealed that conditions of high column porosity yielded a DBC that is ∼70% higher than the EBC. These findings point to potential advantages in terms downstream processing applications, where protein throughput and yield are critical metrics.

Gene redundancy of two-component (chloro)phenol hydroxylases in Rhodococcus opacus 1CP.

Among other factors, a distinct gene redundancy is discussed to facilitate high metabolic versatility of rhodococci. Rhodococcus opacus 1CP is a typical member in that respect and degrades a multitude of (chlorinated) aromatic compounds. In contrast to the central pathways of aromatic degradation in strain 1CP, little is known about the degree of gene redundancy and to what extent this is reflected on protein level within the steps of peripheral degradation. By means of degenerated primers deduced from tryptic peptides of a purified phenol hydroxylase component and using the amplified fragment as a labelled probe against genomic 1CP-DNA, three gene sets encoding three different two-component phenol hydroxylases pheA1/pheA2(1-3) could be identified. One of them was found to be located on the megaplasmid p1CP, which confirms the role of these elements for metabolic versatility. Protein chromatography of phenol- and 4-chlorophenol-grown 1CP-biomass gave first evidences on a functional expression of these oxygenases, which could be initially characterised in respect of their substrate specificity.

Comparison of antibodies hydrolyzing myelin basic protein from the cerebrospinal fluid and serum of patients with multiple sclerosis.

It was found that antibodies (Abs) against myelin basic protein (MBP) are the major components of the antibody response in multiple sclerosis (MS) patients. We have recently shown that IgGs from sera of MS patients are active in the hydrolysis of MBP. However, in literature there are no available data concerning possible MBP-hydrolyzing Abs in cerebrospinal fluid (CSF) of MS patients. We have shown that the average content of IgGs in their sera is about 195-fold higher than that in their CSF. Here we have compared, for the first time, the average content of lambda- and kappa-IgGs as well as IgGs of four different subclasses (IgG1-IgG4) in CSF and sera of MS patients. The average relative content of lambda-IgGs and kappa –IgGs in the case of CSFs (8.0 and 92.0%) and sera (12.3 and 87.7%) are comparable, while IgG1, IgG2, IgG3, and IgG4: CSF - 40.4, 49.0, 8.2, and 2.5% of total IgGs, respectively and the sera - 53.6, 36.0, 5.6, and 4.8%, decreased in different order. Electrophoretically and immunologically homogeneous IgGs were obtained by sequential affinity chromatography of the CSF proteins on protein G-Sepharose and FPLC gel filtration. We present first evidence showing that IgGs from CSF efficiently hydrolyze MBP and that their average specific catalytic activity is unpredictably ∼54-fold higher than that of Abs from sera of the same MS patients. Some possible reasons of these findings are discussed. We suggest that anti-MBP abzymes of CSF may promote important neuropathologic mechanisms in this chronic inflammatory disorder and in MS pathogenesis development.

Preparation and characterization of a thermoresponsive gigaporous medium for high-speed protein chromatography

A high-speed thermoresponsive medium was developed by grafting poly(N-isopropylacrylamide-co-butyl methacrylate) (P(NIPAM-co-BMA)) brushes onto gigaporous polystyrene (PS) microspheres via surface-initiated atom transfer radical polymerization (ATRP) technique, which has strong mechanical strength, good chemical stability and high mass transfer rate for biomacromolecules. The gigaporous structure, surface chemical composition, static protein adsorption, and thermoresponsive chromatographic properties of prepared medium (PS–P(NIPAM-co-BMA)) were characterized in detail. Results showed that the PS microspheres were successfully grafted with P(NIPAM-co-BMA) brushes and that the gigaporous structure was robustly maintained. After grafting, the nonspecific adsorption of proteins on PS microspheres was greatly reduced. A column packed with PS–P(NIPAM-co-BMA) exhibited low backpressure and significant thermo-responsibility. By simply changing the column temperature, it was able to separate three model proteins at the mobile phase velocity up to 2167cmh−1. In conclusion, the thermoresponsive polymer brushes grafted gigaporous PS microspheres prepared by ATRP are very promising in ‘green’ high-speed preparative protein chromatography.

Temperature-responsive membrane for hydrophobic interaction based chromatographic separation of proteins in bind-and-elute mode

Butyl-acrylate (BA) containing branched poly-(N-isopropyl acrylamide) or PNIPAM copolymer was grafted on filter paper to prepare composite membrane for carrying out temperature-responsive hydrophobic interaction membrane chromatography (HIMC) of proteins. The copolymer demonstrated two-step phase transition behavior due to the presence of BA and PNIPAM, making the changeover from hydrophilic to hydrophobic state more tunable. The feasibility of using the temperature-responsive membrane was demonstrated by controlling human immunoglobulin G (hIgG) binding and release using temperature change. Higher temperature promoted protein binding and lower temperature favored protein release in this process, which was carried out using lyotropic salt-free mobile phase. The purification of monoclonal antibody (mAb) hIgG1-CD4 from simulated CHO cell culture supernatant was carried out to demonstrate practical application for the novel temperature-responsive membrane.

Coating Gigaporous Polystyrene Microspheres with Cross-linked Poly(vinyl alcohol) Hydrogel as a Rapid Protein Chromatography Matrix

Gigaporous polystyrene (PS) microspheres were hydrophilized by in situ polymerization to give a stable cross-linked poly(vinyl alcohol) (PVA) hydrogel coating, which can shield proteins from the hydrophobic PS surface underneath. The amination of microspheres (PS-NH2) was first carried out through acetylization, oximation and reduction, and then 4,4'-azobis (4-cyanovaleric acid) (ACV), a polymerization initiator, was covalently immobilized on PS-NH2 through amide bond formation, and the cross-linked poly(vinyl acetate) (PVAc) was prepared by radical polymerization at the surfaces of ACV-immobilized PS microspheres (PS-ACV). Finally, the cross-linked PVA hydrogel coated gigaporous PS microspheres (PS-PVA) was easily achieved through alcoholysis of PVAc. Results suggested that the PS microspheres were effectively coated with cross-linked PVA hydrogel, where the gigaporrous structure remained under optimal conditions. After hydrophilic modification (PS-PVA), the protein-resistant ability of microspheres was greatly improved. The hydroxyl-rich PS-PVA surface can be easily derivatized by classical chemical methods. Performance advantages of the PS-PVA column in flow experiment include good permeability, low backpressure, and mechanical stability. These results indicated that PS-PVA should be promising in rapid protein chromatography.