Changes In Chemical Composition Research Articles

Enhanced adsorption of phenol using graphene oxide-bentonite nanocomposites: Synthesis, characterisation, and optimisation

Wastewater treatment is crucial because it causes harm to the environment of human beings. Adsorbents are faulted by low adsorption capacity and difficult recovery due to organic pollutants. This study aims to improve adsorption capacities using bentonite and other environmentally friendly and economically feasible adsorbents. To do this, using Hammer's approach, bentonite was subjected to an acidic treatment (1.5 M H2SO4) and then hybridized with synthetic graphene oxide (GO). Integrating GO nanosheets within the interlayer of acid-activated bentonite and depositing them onto the exterior surface using a simple ultrasonic-assisted method successfully created a graphene oxide-bentonite nanocomposite. GO, and its composites (at 5 and 10 wt%) were characterized using ATR-FTIR, BET, XRD, FE-SEM, and AFM studies. The results demonstrated that GO with a single-layer thickness of 0.618 nm could be successfully fabricated. We employed energy-dispersive X-ray spectroscopy (EDX) to detect changes in chemical composition before and after phenol adsorption. It was thoroughly studied how essential factors, including adsorbent dosage, pH, agitation period, and beginning phenol concentration, affected adsorption behavior. An obvious increases of the adsorption capacities from 30.69 to 46.43 mg/g were achieved under ideal circumstances of pH 6, an 8-hour contact duration, and doses of 0.3 g and 0.2 g for GO-MB5 and GO-MB10 composites, respectively. The pseudo-second-order kinetic and Langmuir equilibrium isotherm models efficiently described the adsorption process. More notably, the synthesized adsorbents could be successfully regenerated and used without major capacity losses after six cycles. This study highlights the effectiveness of GO-bentonite nanocomposites as effective adsorbents for environmental treatment.

Identification of Hydrochemical Characteristics, Spatial Evolution, and Driving Forces of River Water in Jinjiang Watershed, China

Rivers are an important source of water in humid regions, but their availability is greatly limited by water chemistry. In order to accurately identify the changes in river water chemical composition, the compositional analysis method (CoDA) is proposed from the perspective of compositional data analysis theory, which considers the geochemical riverine system as a whole and detects the compositional changes of the entire watershed. The basic data analysis is carried out by traditional analysis methods, and the results show that the hydrochemical characteristics of different sections of the basin have significant features. The water chemistry of Dongxi River is of the HCO3− Ca type. The water of the Xixi River shows a gradual evolution from the HCO3-Ca type and high SO42− content in the upper reaches to the Cl-Ca type in the lower reaches. The hydrochemistry of river water in the watershed is mainly affected by rock weathering leaching (PC1) and agricultural and domestic pollutant discharge (PC2), with a contribution rate of 48.4% and 19.7%, respectively. Rock weathering, mining, and agricultural pollution are the main factors affecting the chemical composition of river water in different regions. The spatial composition of a single sample at different scales is monitored by the Mahalanobis distance approach in an iterative manner to minimize the influence of a single anomaly on the composition center. The results show that the main reasons for the change in river water chemical composition along the Xixi River are attributed to mine pollution, domestic pollution, and tea plantation and that along the Dongxi River is caused by domestic pollution. The hydrochemical composition changes after the confluence of the Xixi River and Dongxi River are mainly affected by human activities and seawater in urban areas. This research could provide new perspectives and methods for detecting the influences of human and natural factors on the hydrochemistry of river water in humid regions worldwide.

Investigating best practice for specimen preparation for biological testing of root canal sealers

IntroductionBiological characterization of root canal sealers is important as it assesses the ability of the root canal sealer to exert antimicrobial properties thus avoiding treatment failures caused by microbial challenge and also assess the cytotoxic effect on the periapical tissues. Assessment of the biological testing of root canal sealers necessitates the sterilisation of the materials prior to evaluation. This study aims to analyse the influence of various sterilisation techniques conducted prior to biological testing on the microstructure and surface properties of endodontic sealers. Assessment of the initial microbial contamination on the material was also undertaken. MethodsFour commercial sealers were investigated. The sealers were either prepared in a laminar flow cabinet or on a laboratory bench top under ambient conditions. Each group was further divided into 5 groups (n = 3) based on the sterilization technique:1) ethanol-10 mins, 2) ultraviolet-1 h, 3) ethanol-10 mins + ultraviolet-1 h, 4) autoclave, and 5) no sterilisation (control). Microbial levels in the materials were assessed by plate streaking technique. The materials were characterized by scanning electron microscopy and energy dispersive spectroscopy, and Fourier transform infrared spectroscopy, before and after sterilisation, to assess any changes in microstructure and chemical composition. ResultsAll the materials did not exhibit contamination when prepared in laminar flow chamber in sterile conditions compared with sealers prepared on the bench top. Three of the commercial materials showed changes in microstructure while one (TotalFill) was not affected by the sterilisation. AH Plus and BioRoot RCS exhibited alterations in water and alcohol peaks in FT-IR while the single syringe sealers (TotalFill and BioRoot Flow) showed no changes. ConclusionsSterilisation methods cause physical and chemical alterations to sealers. Material preparation should be performed in a laminar flow cabinet and a test for sterility should be performed prior to any biological testing being undertaken. If the materials are not sterile, assessment of the effects of the sterilization methods is recommended.

EFFECTS OF COMBINED CHEMICAL AND HYDROTHERMAL PRETREATMENT ON PAPYRUS CELLULOSE STRUCTURE

"Papyrus (Cyperus papyrus L.) is a lignocellulosic plant suitable for many applications when properly pretreated. This study explores the potential of a two-stage pretreatment (combining hydrothermal and chemical methods) on the characteristics of cellulose fibers derived from papyrus. One-stage and two-stage pretreatments were compared, utilizing sodium hydroxide (NaOH) and ferric chloride (FeCl3) chemical solutions at a 3% (w/v) concentration. Chemical pretreatment was employed for one-stage processing, while hydrothermal pretreatment was introduced prior to chemical pretreatment. As the liquid hot-water process intensified, significant changes in chemical composition and morphology occurred. Hydrothermal pretreatment partially eliminates hemicelluloses and lignin, while increasing the cellulose content and enhancing fiber crystallinity. Following the pulping and bleaching stages, it was determined that the FeCl3-based two-stage pretreatment exhibited the greatest potential for cellulose recovery and hemicelluloses and lignin removal, yielding the highest crystallinity index."

Probing Physicochemical Performances of 3D Printed Carbon Fiber Composites During 8‐Month Exposure to Space Environment

AbstractCarbon fiber reinforced polymers (CFRPs) offer exceptional properties that make them highly relevant in the aerospace industry, such as high thermal conductivity and an outstanding strength‐to‐weight ratio. Advances in additive manufacturing have expanded the aerospace applications of CFRPs, even allowing for in‐space fabrication of complex structures. Understanding the stability of CFRPs in the harsh conditions of low Earth orbit (LEO) is crucial. LEO exposes materials to extreme environmental factors, such as vacuum, radiation, atomic oxygen, and temperature fluctuations, which can accelerate degradation. To investigate the space‐environment effect on material, changes in properties of 3D‐printed CFRPs are compared with CFRPs made through forging and conventional compression molding. Surface analyses examine morphological, chemical, and matrix composition changes, along with an evaluation of mechanical integrity. Remarkably, the naked 3D printed CFRPs withstood 8 months of LEO exposure similar to the compression molded CFRP samples, with changes in chemical properties limited to the sample's outer surface. Further, despite no protective coatings are used, limited surface erosion and no variation in mechanical strength are observed. These results provide relevant information for the development and deployment of novel 3D printed CFRPs materials for a wide spectrum of terrestrial and space applications.

Aluminum tantalum oxide thin films deposited at low temperature by pulsed direct current reactive magnetron sputtering for dielectric applications

This research aims at studying aluminum tantalum oxide thin films (AlxTayOz) deposited at low temperature for dielectric applications. These ternary oxide layers are synthesized at 180 °C by physical vapor deposition (PVD), specifically the mid-frequency pulsed direct current reactive magnetron sputtering. The deposition process uses targets made of a mixture of aluminum and tantalum in various proportions. Four target compositions are studied containing 95 at.%, 90 at.%, 80 at.%, and 70 at.% of aluminum, corresponding to 5 at.%, 10 at.%, 20 at.%, and 30 at.% of tantalum, respectively. The ternary oxide thin films of AlxTayOz are compared to aluminum oxide (AlxOz) and tantalum oxide (TayOz) layers produced in the same experimental conditions. The AlxTayOz thin films are dense, uniform, and amorphous regardless of the experimental conditions used in this study. Their chemical composition changes as a function of the target composition. The oxygen flow used during deposition also affects the chemical composition of the oxide layers and the deposition rate. The oxide thin films with tantalum are deposited at higher deposition rates and contain more oxygen. Tantalum also promotes the amorphization of the oxide layers. The highest dielectric strength is measured for the thin film containing a low amount of tantalum combined with a high amount of oxygen.

Impact of ground adsorption capacity on the change in chemical composition of groundwater

Impact of ground adsorption capacity on the change in chemical composition of groundwater

The Origin of Strain Effects on Sulfur Redox Electrocatalyst for Lithium Sulfur Batteries

AbstractIntroducing strain is considered an effective strategy to enhance the catalytic activity of host material in lithium‐sulfur batteries (LSB). However, the introduction of strain through chemical methods often inevitably leads to changes in chemical composition and phase structure, making it difficult to truly reveal the essence and root cause of catalytic activity enhancement. In this paper, strain into MoS2 is introduced through a simple heat treatment and quenching. Experimental research and theoretical analysis show that the strain raises parts of antibonding orbitals in Mo─S bonds above the Fermi level and weakens Li─S and S─S bonds, resulting in tight anchoring and accelerating the conversion for lithium polysulfides (LiPSs). The cells based on the MoS2 with high strain delivers an initial discharge specific capacity as high as 1265 mAh g−1 under 0.2 C and a low average capacity fading of 0.041% per cycle during 1500 cycles under 1 C. This research work deeply reveals the origin of strain effects in the reaction process of LSB, providing important design principles and references for the rational design of high‐performance catalytic materials in the future.

Optimizing the thermophysical qualities of innovative clay–rGO composite bricks for sustainable applications

This work concerned the development of a unique reduced graphene oxide (rGO) nano-filler to provide innovative opportunities in enhancing the thermophysical performance of clay composite bricks. Whereas, a series of clay–rGO composite bricks were produced, doped with various levels of rGO nanosheets (i.e., 0, 1, 2, 4, and 6 wt% clay). Each clay–rGO composite’s microstructure, shrinkage, morphology, density, porosity, and thermophysical characteristics were carefully investigated, and the thermal conductivity performance was optimized. Incorporation of different levels of rGO NPs to the clay matrix allowed all the peaks intensity to rise relative to the untreated one in the XRD pattern. Meanwhile, the inclusion of these doping resulted in a grew in the crystallite sizes and apparent porosity within the compositions. In this vein, shrinkage fracture of fabricated brick composites varied depending on dopants type and levels during the drying and firing processes. Moreover, there are some changes in chemical compositions, as well as wave shifts, suggesting that functional groups of rGO may have contributed to partially introduce carbonyl groups in clay–rGO composites. Besides, the porous topography and bulk density improved rapidly with respect to the plane of the rGO nanosheets within the composites. The differ-dense microstructure displayed in the SEM micrographs supports these outcomes. Remarkably, clay–(4%)rGO compound not only has an optimum thermal conductivity value (0.43 W/mK), but it also has a high heat capacity (1.94 MJ/m3K). These results revealed the exceptional features of rGO sheets such as large surface area with high porosity within the modified clay composites.

Synthesis and characterization of new composite sponge combining of metal-organic framework and chitosan for the elimination of Pb(II), Cu(II) and Cd(II) ions from aqueous solutions: Batch adsorption and optimization using Box-Behnken design

By using a one-step hydrothermal process in an acidic environment, an unique Ag-MOF/chitosan composite sponge (Ag-MOF/CSC composite sponge) was effectively created. Chitosan synthesis has been studied for more than half a century, but its Use for adsorption of heavy metals (HM) is presently being researched. As Particularly with regard to adsorbents constructed of metal organic framework, to increase an adsorbent material's adsorption capacity, its composition is commonly changed. Pb(II), Cu(II), and Cd(II) adsorption and elimination were examined in this study in relation to the composite Ag-MOF/CSC sponge. Following thorough analysis including measurements of the surface area using Brunauer-Emmett-Teller, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and SEM and Fourier transform infrared spectroscopy (FTIR) (BET).The Ag-MOF/CSC composite sponge exhibits an impressive large surface area of 1496.58 square meters per gram, besides having the best capacity for adsorption (qmax) for various ions: 1.80, 1.49 and 1.72 mmol per gram for Pb(II), Cu(II) and Cd(II), respectively. Consider the factors that influence the adsorption characteristics, such as temperature, pH, metal concentration, and adsorbent dosage. The kinetic isotherm and the adsorption isotherm were fitted using the pseudo-second-order equation and the Langmuir equation, respectively. It was shown that the adsorption process was endothermic and spontaneous in accordance with adsorption thermodynamics. With rise in temperature, more metal were absorbed. With good efficiency, no change in chemical composition, and similar XRD and XPS data before and after reuse, the Ag-MOF/CSC composite sponge was repurposed six times. Investigate the mechanism of interaction between the heavy metals and the Ag-MOF/CSC composite sponge. Utilizing Box-Behnken design, the adsorption outcomes were optimized (BBD).

Intriguing properties of graphite/polysiloxane composite-based pencil electrodes

Pencil leads can be considered well-defined and cheap graphite electrodes for a wide range of electrochemistry applications. These electrodes display many intriguing properties; however, the origin of these properties is not clear. Using various analytical approaches applied to two different commercially available Tombow (TO) and Staedtler (ST) pencils we reveal a causal relationship between the unique properties of pencils and their graphite/polysiloxane composite. We explore the impact of chloroform etching on chemical composition changes, thermal stability and electrochemical parameters of pencils. Using a combination of X-ray photoelectron spectroscopy (XPS) and gas chromatography-mass spectrometry (GC-MS/MS) various polydimethylsiloxanes in composites are revealed. The polysiloxane species leave into the chloroform solvent during the etching resulting in a significant decrease of their content within the electrodes. Differential scanning calorimetry (DSC) data, corroborated by gravimetric measurements, provide additional proof of the presence of composite structures in ST and TO pencils, showing glass transition temperatures at around 76 °C and 81 °C. The main difference between the TO and ST electrodes is the content and composition of the polysiloxanes within the graphite matrix. ST composites have significantly higher polymer content (∼ 30 %) with traces of Na and S impurities compared to TO ones (∼ 14 %) free of contaminations. Furthermore, mainly cyclic nanostructures appear in chloroform extracts of ST composites whereas rather chain-like clusters are liberated out of the TO counterparts. Complementary electrochemical experiments using cyclic voltammetry (CV), impedance spectroscopy (EIS) and the less known elimination voltammetry with linear scan (EVLS) reflect the performance superiority of TO electrodes with much lower polysiloxane content and free of impurities. High conductivity, low capacitive current along with favoured charge carrier transfer all promise a wide range of technological applications for the TO pencil material.

Numerical Prediction of Changes in Atmospheric Chemical Compositions During a Solar Energetic Particle Event on Mars

AbstractPrecipitation of solar energetic particles (SEPs) into planetary atmospheres causes changes in atmospheric chemical composition through ionization, dissociation, and excitation of atmospheric molecules. In contrast to the terrestrial atmosphere, where depletion of ozone in the polar mesosphere has been studied by observations and models for decades, there have been no studies on the effects of SEPs on the neutral chemical composition of Mars' present‐day atmosphere. This study provided the first estimate of the impacts of SEPs on neutral chemical composition in the present‐day Martian atmosphere coupling a Monte Carlo model and a one‐dimensional photochemical model. Our results showed that ozone density in the Martian atmosphere might decrease in the altitude range of 20–60 km with a factor 10 maximum enhancement occurring at 40 km during a Halloween‐class SEP event due to an enhanced concentration of HOx. The depletion of ozone occurred in the altitude range of 20–60 km, corresponding to the penetration of protons with an energy range of 4.6–46 MeV. Such ozone depletion should be detected by Trace Gas Orbiter/Nadir and Occultation for MArs Discovery during intense SEP event. A 75% depletion of the ozone density at 40 km can be expected during SEP events occurring once in every 1 year. Therefore, ozone concentration in the Martian atmosphere might sufficiently decrease during a SEP event as on Earth, but through different chemical pathways driven by CO2 ionization and CO recombination catalytic cycle.

Advanced thin films of indium-tin oxide doping with photosensitive polymer via embossing process

We propose a sol-gel thin film formation process involving nanoimprint lithography. First, indium tin oxide was dissolved in 2-methoxyethanol at a ratio of 5:5 and the mixture were mixed with 10 wt% of a UV-curable. Subsequently, a polydimethylsiloxane sheet prepared by covering a silicon wafer with a polydimethylsiloxane mold was attached to a InSnO thin film to duplicate the nanostructure through UV irradiation exposure. The replicated nanostructured thin films formed about morphological and chemical composition changes on the surface, we progressed to x-ray photoelectron spectroscopy and atomic force microscopy analysis. Furthermore, atomic force microscopy image analysis showed superior patterned grooves for a UV exposure time of 3 min. A suitability test involving the measurement of the transmittance was performed for examining the suitability of the thin film for use in display devices.

Qualitative Evaluation for Asphalt Binder Modified with SBS Polymer

Solutions for safer, more durable infrastructure are required in light of increasing traffic and severe weather in Iraq. The most significant road conservation and maintenance challenges are the pavement's low resistance to dynamic loads and short service life. As a result, vast sums of money are spent annually to enhance the road service capacities in Iraq. Thermoplastic electrometric polymers for bitumen modification create long-lasting, cost-effective roadways. This study aims to determine how the mechanical properties of neat asphalt binder change when styrene butadiene styrene (SBS) is added as a modifier. The current research investigates adding three percentages of SBS (3, 5, and 7% of the weight of bitumen). Both neat and polymer-modified bitumen (PMB) were subjected to a series of physical laboratory and Superpave tests, including a dynamic shear rheometer tester (DSR) and a storage stability test. In addition, a chemical analysis test was conducted to identify any change in the neat binder chemical composition due to the addition of SBS polymer. The results indicated that 5% of SBS polymer was the optimum addition percentage to the local asphalt in Iraq. Additionally, it reduced the susceptibility of bitumen to temperature changes and enhanced its characteristics in all laboratory tests. The obtained PMB significantly improved rutting and fatigue factors compared to the neat asphalt binder. Based on the DSR tester and the storage stability test, the ratio of 5% SBS met the requirements of class PG76-10, used in the central and southern governorates of Iraq. Using SBS polymer on the surface course in Iraq reduces road damage due to the scorching summer sun, reduces the likelihood of rutting and fatigue cracking, and works well in hot regions, resulting in roads that last longer, provide comfortable riding, and require less maintenance.

Changes in sensory characteristics, chemical composition and microbial succession during fermentation of ancient plants Pu-erh tea

“Ancient tea plants” are defined as tea trees > 100 years old, or with a trunk diameter > 25 cm; their leaves are manufactured to high - quality, valuable ancient plants pu-erh tea (APPT). In this study, a fermentation of APPT were developed, and outstanding sweetness of APPT infusion was observed. During fermentation, the content of soluble sugars, theabrownins (p < 0.05), as well as 41 metabolites were increased [Variable importance in projection (VIP) > 1.0; p < 0.05 and Fold-change (FC) FC > 2]; While relative levels of 72 metabolites were decreased (VIP > 1.0, p < 0.05 and FC < 0.5. Staphylococcus, Achromobacter, Sphingomonas, Thermomyces, Rasamsonia, Blastobotrys, Aspergillus and Cladosporium were identified as dominant genera, and their relative levels were correlated with contents of characteristic components (p < 0.05). Together, changes in sensory characteristics, chemical composition and microbial succession during APPT fermentation were investigated, and advanced the formation mechanism of its unique quality.

Structural, defense enzyme activity and chemical composition changes in the xylem of Aquilaria sinensis during fungus induction

Agarwood is a dark resinous wood, of high quality and in a short period, can be formed after inoculation with the efficient fungus in Aquilaria sinensis. However, the action site and mechanism of the fungus inducing the agarwood formation remain unclear. In this work, the efficient fungal infection was used to induce agarwood formation on A. sinensis, and samples were collected according to inoculation time. Subsequently, the xylem structure, histochemistry, defense enzyme activities, and the accumulation and in-situ distribution of chemical composition were investigated. The transition layer (TL) was the critical layer for the continuous accumulation of agarwood, and began to appear in the injection of fungal inducers for 15 days (15D). The parenchyma cells of the xylem rays and interxylary phloem were the main action site of fungus in the formation and accumulation of agarwood. The sesquiterpenes and 2-(2-phenylethyl) chromones (PECs) were mainly accumulated in the agarwood layer (AL) and decay layer (DL), while their relative contents were highest in the injection of fungal inducers for 30 days and 180 days (30D and 180D), respectively. Among them, PECs appeared earlier than sesquiterpenes, and both were flindersia-type PECs. They were mainly concentrated in the cell corners and intercellular layer of the cell wall. In addition, Redundancy analysis (RDA) and Mantel test revealed that the different layer percentage (DLP), phenylalanine ammonia lyase (PAL), and starch grains (SG) were the drivers of PECs, and catalase (CAT) was the driver of sesquiterpenes. Therefore, this study will provide a theoretical foundation for revealing the mechanism of fungus-induced agarwood formation and inducing high-quality and high-yielding agarwood in the future.

Plum (Prunus domestica) Extract Acts as a Natural Antioxidant in Minced Sardine Muscles During Frozen Storage

ABSTRACT The potential usage of plum extract (PE) in minced sardine systems as a natural antioxidant was studied. Methanol-extracted PE indicated the highest antioxidant activity and was used (1%, 2%, 3%) in minced fish treatments. PE did not cause significant changes in chemical composition, while it decreased pH values. Redness and yellowness were not affected, although lightness decreased with increasing levels of PE. The extract was effective to retard oxidation by decreasing free fatty acids, peroxide, and malondialdehyde concentrations during frozen storage. Consequently, PE could be used up to 3% as a natural source in fish mince.

Mechanism of elemental segregation around extended defects in high-entropy alloys and its effect on mechanical properties

Elemental segregation around extended defects is common in high-entropy alloys (HEAs) composed of multi-principal elements, which profoundly impacts their mechanical properties. In HEAs, the driving force for segregation usually competes with chemical short-range ordering (CSRO) formation, making it challenging to elucidate the segregation mechanisms. In this study, we systematically investigate the chemical composition changes around extended defects, including dislocations, stacking faults, and grain boundaries (GBs) in CoNiCrFe HEAs, to explore the chemical-structure-mechanical relationship utilizing hybrid Monte Carlo and molecular dynamic (MC/MD) simulations and theoretical analysis. We find a pronounced Cr enrichment and Co/Ni/Fe depletion around all defects considered in this work. A correlation between the degree of structural disorder and the chemical segregation/depletion phenomenon in the proximity of extended defects has been uncovered. Our results show that due to the extreme chemical complexity in HEAs, CSRO inevitably contributes to the elemental rearrangement and affects segregation. Consequently, the segregation behavior in HEAs is mainly controlled by interactions between different atomic pairs, and the segregation entropy also plays a dominant role. By decoupling the strengthening contribution from elemental segregation and CSRO, we demonstrate and highlight that the strengthening in HEAs can be modulated by elemental segregation. The positive impact of element segregation on interfacial properties - improved ultimate tensile strength and elongation, has been evidenced through experimental comparisons of CoNiCrFe with different Fe additions. This work elucidates the mechanism of heterogenous elemental distributions in HEAs where elemental segregation and CSRO coexist, paving the way for manipulating their mechanical properties by modulating the compositional variations.

Boric Acid as A Low-Temperature Graphitization Aid and Its Impact on Structure and Properties of Cellulose-Based Carbon Fibers.

In the present paper, a scalable, economically feasible, and continuous process for making cellulose-based carbon fibers (CFs) is described encompassing precursor spinning, precursor additivation, thermal stabilization, and carbonization. By the use of boric acid (BA) as an additive, the main drawback of cellulose-based CFs, i.e., the low carbon yield, is overcome while maintaining a high level of mechanical properties. This is demonstrated by a systematic comparison between CFs obtained from a BA-doped and an un-doped cellulose precursor within a temperature range for carbonization between 1000 and 2000 °C. The changes in chemical composition (via elemental analysis) and physical structure (via X-ray scattering) as well as the mechanical and electrical properties of the resulting CFs were investigated. It turned out that, in contrast to current opinion, the catalytic effect of boron in the formation of graphite-like structures sets in already at 1000 °C. It becomes more and more effective with increasing temperature. The catalytic effect of boron significantly affects crystallite sizes (La, Lc), lattice plane spacings (d002), and orientation of the crystallites. Using BA, the carbon yield increased by 71%, Young's modulus by 27%, and conductivity by 168%, reaching 135,000 S/m. At the same time, a moderate decrease in tensile strength by 25% and an increase in density of 14% are observed.

Effect of phlorotannin extracts from Ascophyllum nodosum on the textural properties and structural changes of Apostichopus japonicus

In this work, phlorotannin extracts (PhTEs) were isolated from Ascophyllum nodosum. The effects of PhTEs on the textural properties, structural changes and oxidation level of Apostichopus japonicus (A. japonicus) were investigated. The results showed that thermal treatment could lead to the dissolution of TCA-soluble peptides and free hydroxyproline and promote the degradation of A. japonicus. The chemical compositional changes and texture profile analysis results indicated that PhTEs could effectively inhibit the degradation of A. japonicus and improve the hardness and chewiness of A. japonicus. Analysis of multiple spectroscopic methods suggested that the secondary and tertiary conformations tended to be stable after PhTEs were added. In addition, electron spin resonance results indicated that PhTEs could reduce the oxidation level of A. japonicus. These results suggest that the degradation of A. japonicus during mild heat treatment can be regulated by PhTEs, which provides insights for quality control in A. japonicus heat treatment.