Characteristics Of Wood Research Articles

Variation of anatomical characteristics of Nothofagus alpina wood grown under three silvicultural conditions

Variation of anatomical characteristics of Nothofagus alpina wood grown under three silvicultural conditions

Fire behavior of furfurylated paulownia wood

ABSTRACT Wood is an aesthetically pleasing, sustainable material for various uses. All materials, including wood, are intended to be long-lasting, maintaining their original appearance. The effects of furfurylation on the fire characteristics of wood are still unclear, even though it significantly increases the dimensional stability, hardness, and biodegradation resistance of wood. This study aimed to evaluate the fire characteristics of furfurylated wood. Thermogravimetric analysis showed that the time required for the infiltration of furfuryl alcohol into the samples significantly exceeded the values commonly reported in the literature. The results obtained by measurements on a cone calorimeter indicate that furfurylation significantly increases peak values of heat release rate, carbon monoxide, carbon dioxide, and smoke production in the phase immediately after the initiation. On the contrary, carbon-monoxide (CO) production decreased in the phase of heterogeneous combustion of carbonaceous residue.

Willow, Poplar, and Black Locust Debarked Wood as Feedstock for Energy and Other Purposes

Solid biomass can be used for energy generation and the production of various renewable bioproducts. The aim of this study was to determine the yield and characteristics of wood obtained as debarking residue from 14 genotypes of short-rotation woody crops (SRWCs). These included five Populus genotypes, one Robinia genotype, and eight Salix genotypes, harvested in both annual and quadrennial cycles. The results showed that the highest dry wood yield (12.42 Mg ha−1 y−1 DM) and yield energy value (244.34 GJ ha−1 y−1) were obtained from willow (cultivar Żubr) harvested in a quadrennial cycle. The best effect among the poplar genotypes was achieved for the Hybryda275, and it was particularly marked in the quadrennial harvest cycle. The poorest results were determined for black locust. The Robinia characteristics included the significantly lowest moisture content (31.6%), which was a positive attribute from the energy point of view, but, on the other hand, it had some adverse characteristics—the highest levels of sulfur (0.033% DM), nitrogen (0.38% DM), and ash (0.69% DM). More beneficial properties in this respect were determined for willow and poplar wood. Moreover, willow and poplar wood contained more cellulose—51.8 and 50.0% DM, respectively—compared with black locust. Extending the SRWC shoot harvest cycle from annual to quadrennial resulted in an increase in cellulose, lignin, and carbon, higher heating value, and a decrease in nitrogen, sulfur, ash, and moisture content. Therefore, extending the harvest cycle improved the parameters of SRWC wood as an energy feedstock.

SHORT NOTES. THERMAL CHARACTERISTICS OF SENGON WOOD DRYING USING INFRARED AND COMBINED INFRARED-HOT AIR METHODS

This research aimed to determine the thermal characteristics of sengon wood due to drying at temperature of 70, 80, and 90oC with air velocity of 1 and 3 m/s using infrared (IR) and combined infrared-hot air (IR-HA) method. The thermal characteristics analyzed included temperature distribution, reduction in moisture content, and drying rate. The results of drying wood samples using IR method showed that the fastest drying time was obtained at 90oC with air velocity of 1 m/s. However, for combined IR-HA method, the optimal condition was achieved at air velocity of 3 m/s. The largest drying rate attained using combined IR-HA method was 0.27 g/min, while the smallest was recorded at 0.094 g/min with IR method. These results showed that combined IR-HA method produced a more evenly distributed temperature and faster drying time compared to the IR method.

Study on damage and fracture characteristics of wood based on acoustic emission b-value and seismic magnitude difference entropy

To assess the damage and fracture behavior of wood under load, a wood damage assessment method was proposed based on acoustic emission (AE) b-values and seismic magnitude difference entropy. First, AE signals from Pinus sylvestris var. mongolica (softwood) and Zelkova schneideriana (hardwood) specimens were collected separately at a sampling frequency of 500 kHz in a three-point bending test. Then, 52 dB was taken as the threshold of the AE event, and the b-value and seismic magnitude difference entropy were calculated at 4-s intervals. Finally, by comparing with the load‒time curve, the b-value and seismic magnitude difference entropy were used to evaluate the damage fracture degree. The results showed that an increase in the b-value indicates the accumulation of strain energy, and vice versa, corresponding to the concentrated release of strain energy. At the same time, the test process can be divided into three stages—elastic, elastic‒plastic and plastic—based on the level of the seismic magnitude difference entropy.

Macroscopic and microscopic diagnosis of three Entandrophragma species traded in Türkiye

The anatomical characteristics are highlighted for Entandrophragma cylindricum, Entandrophragma utile, and Entandrophragma angolense. Wood samples, which were previously obtained from commercial timber industries in the Marmara region of Türkiye and used as course materials, were used. Qualitative and quantitative anatomical characteristics were determined. Qualitatively, characters such as distinct growth rings, diffuse-porous wood, deposits in vessel elements, simple perforation plates, alternate intervessel pits, heterogeneous ray type, and septate fibres, were common to all species. The quantitative evaluation showed that there were differences between species. Entandrophragma species differ in some wood characteristics such as the tangential diameter of the vessel, ray height, ray width, and fibre lumen diameter. E. utile had higher values of the mean tangential vessel diameter (180 μm) and fiber lumen diameter (18.4 μm) than the other two species. It is possible to say that the anatomical features of E. cylindricum differ from that of other species and that it will be easier to diagnose among other species. E. cylindricum had the lowest values of the mean tangential vessel diameter (147 μm) and ray height (361 μm). Distinctive characters for E. utile and E. angolense are tangential vessel diameter, vessel length, ray height, ray width, and all fibre dimensions.

Research data in paleobotany: petrographic thin sections fossil wood dataset

Objective: This study was aimed at analyzing and disseminating the fossil wood collection data stored in the thin slide sections of the paleobotany collection of the Department of Paleontology and Stratigraphy of the Institute of Geosciences of a university in Southern Brazil. Thin sheets of petrified wood are described. Research data used in geosciences specifically seek to develop a model for the use of this type of sheet in paleobotany, enabling visualization of its representativeness in studies published over 40 years to obtain the anatomical characteristics of fossil woods and define their systematic affinities as a specific typology of research data in geosciences. Methods: The methodology involved interviewing a paleobotanical specialist and using different techniques applied in metric studies to map scientific production. Thus, a dataset of (20) thin slide sections of petrified fossil wood used in “Stressing environmental conditions in the “petrified forest” from the Mata Sequence in the Triassic context of the Paraná Basin,” a paper published by the Journal of South American Earth Sciences (DOI:10.1016/j.jsames.2023.104415), was used. Depending on the methodology, these thin petrified wood sheets can reveal paleoclimatic signatures based on the anatomical characteristics of the fossil wood. In addition to this case study, which represents a collection of more than (2.000) thousand blades of fossil wood and approximately 40 years of research, the paleobotanical collection of the department is reused in methodology classes. The collection comprises a database created by research physicists that provides information on anatomical features, systematic affinities, paleoclimatic conditions, and paleoenvironmental insights. Potential for reuse: The reuse, registration, storage, identification, and preservation of thin slide sections as a type of research data used in paleobotany aims to improve the methodology associated with the organization of the physical database of the institution. The research data and blades of fossil wood are being digitized, and soon will be available under the CC BY 4.0 license in the ZENODO repository, according to the sample described here in this data paper (DOI Mendeley:10.17632/b8phfcsync.1). Furthermore, the data can be reused in optical and electronic scanning microscopy software.

Large Wood Transport and Accumulation Near the Separation Zone of a Channel Confluence

AbstractFallen trees enter the adjacent stream and are carried away downstream by the current. As the stream joins another one, the complex hydrodynamics near their confluence make the movement of wood hard to predict. These woods may accumulate near the confluence resulting in backwater and subsequent potential flooding. A laboratory study was conducted to investigate the movement and accumulation behavior of individual pieces of wood near the confluence. The characteristics of wood (i.e., the length, diameter, and density) and the hydraulic conditions (i.e., the discharge ratio and the release distance) were varied in this investigation. It was found that the wooden pieces released from the tributary got occasionally trapped in the flow separation zone of the confluence, whereupon they were mainly trapped by a clockwise vortex and continued to stay driven by a reverse cluster of currents within this zone. The accumulation probability of wood was mainly related to its length, the discharge ratio and the release distance. The effect of wood diameter and density within the tested parameters was negligible. The probability increased with an increase in the discharge ratio as well as a decrease in the release distance. The longer pieces had a higher probability of being trapped, whereas for those exceeding some critical value, the probability was nearly the same, or dropped sharply. A generalized model for wood accumulation near the confluence was developed for practical application. These findings carry significant implications for river management, particularly in preventing the risk of flooding caused by wood blockage.

Perbandingan Teknik Isolasi DNA pada Daun dan Kayu Sonokeling (Dalbergia latifolia)

Sonokeling (Dalbergia latifolia) is a hardwood plant, resistant to termite attack, its wood has beautiful patterned fibers and textures, so it is widely used for furniture in luxury categories with high economic value. According to CITES (Convention on International Trade in Endagered Species of Wild Fauna and Flora), rosewood trade status is included in appendix II. In the trade of rosewood in both domestic and international markets, there are relatively many obstacles and difficulties in identifying the origin of rosewood. It is very important to establish a reference on the identity of wood based on the location of origin as an effort to prevent illegal trade, namely by using a molecular-based identification approach (DNA fingerprinting). In the isolation of rosewood DNA, special techniques are required due to its hard wood characteristics. This study aims to compare DNA isolation techniques from rosewood and rosewood leaves using the CTAB (Cetyl Trimethyl Ammonium Bromide) protocol and the DNA Mini Kit Plant protocol. The research used molecular biology-based identification methods. PCR results showed that the DNA isolation protocol using the commercial kit outperformed the CTAB protocol for both leaf and wood samples. DNA isolation from wood samples was more difficult than leaf samples. Overall, the best protocol for DNA isolation from rosewood leaves and wood was to use a commercial kit.

Forest Adaptation to Climate Change: Altitudinal Response and Wood Variation in Natural-Growth Cunninghamia lanceolata in the Context of Climate Change

This research delves into the impact of climate change on the wood traits of Cunninghamia lanceolata across various altitudinal gradients, aiming to understand the influence of altitude and climatic factors like temperature and precipitation on key wood characteristics. Employing a comprehensive approach, samples were collected from different altitudes for detailed phenotypic analysis. Methods included Pearson correlation, principal component analysis, cluster analysis, and random forest analysis. Results revealed significant variations in wood traits such as heartwood ratio, tracheid length, and width across altitudes. Notably, wood traits in lower- and middle-elevation populations exhibited higher variability compared to higher elevations, indicating greater environmental diversity and genetic adaptability at these altitudes. Climatic factors, particularly temperature and precipitation, were found to increasingly influence wood trait variation with altitude. The research concludes that the adaptation of Cunninghamia lanceolata to climate change is significantly influenced by both altitudinal and climatic factors, highlighting their importance in forest genetic breeding and conservation strategies amidst global climate change.

Large wood recruitment, retention and mobilization in low-order streams of the Brazilian Savanna

The delivery of wood to streams varies in space and time and may occur continuously or episodically. Once in a stream, wood may be retained or transported due to the balance between driving (water flow) and resisting forces (channel features and wood characteristics). Despite there being few studies directly measuring wood mobility, notable variations in annual transport rates and mean travelled distances have already been detected worldwide. In the tropics, due to wetter and warmer conditions and consequently higher decay rates and peak discharge, wood is believed that more readily degraded and transported downstream. However, there exists a knowledge gap regarding wood dynamics in tropical streams and even more considering tropical non-forested environments. In the present study, we aimed to document large wood (LW) recruitment, retention, and mobilization over a period of one year in eight low-order streams of the Cerrado (the South American Savanna) by tagging and tracing LW pieces. We detected high LW transport and recruitment rates in Cerrado streams, such that the total wood amounts remained constant over time. However, there were important differences between streams due to their distinct channel morphologies and the occurrence of episodic events. The LW length and diameter, original location and orientation were the most important factors in the prediction of the LW travelled distance, which ranged from zero to almost 100 m in one year. Our findings provide unprecedented information regarding wood mobility in tropical savanna streams in South America. To further advance knowledge about the dynamics of wood in Cerrado streams, future studies should characterize the great diversity of wood, especially with regard to densities that may strongly affect wood mobility. Furthermore, it is essential to perform long-term studies to document the dynamics of wood over years in these environments.

Impact of wood surface roughness on optical properties of photonic crystal and amorphous photonic crystal structural color coatings

ABSTRACT Photonic crystal structural coloration represents a novel method for surface decoration of wood. Employing thermal-assisted gravity deposition and spray coating techniques, this study fabricated photonic crystal (PC) and anisotropic photonic crystal (APC) coatings on Aspen and African blackwood surfaces with varying roughness. Taking into consideration wood characteristics such as color and texture, the correlation between wood surface roughness and the decorative effects of PC and APC coatings was analyzed. In summary, lower wood surface roughness enhances the optical effects of PC coatings. Different effects are observed when constructing PC coatings on wood with varying colors. APC coatings fail to achieve decorative effects on light-colored wood, and for dark-colored wood, maintaining a higher level of wood surface roughness is recommended when applying APC coatings for optimal decorative outcomes.

Short-term hygro-mechanical behaviour of lime wood (Tilia cordata) in principal anatomical directions

Abstract The hygroscopic and moisture-dependent mechanical characteristics of small-leaved lime wood (Tilia cordata) were investigated experimentally. This study includes sorption, swelling and shrinkage experiments, as well as tension and compression tests in the three principal anatomical directions at four relative humidity levels. Four sample groups from trees of three different locations in Germany were used. The findings are comparable to those of earlier studies. The hygro-expansion anisotropy is relatively small. Young’s moduli at tension/compression decreased by about 52 %/64 % in radial, 19 %/48 % in tangential and 16 %/58 % in longitudinal direction for an increase of moisture content from 10 % (65 % RH) to 20 % (95 % RH). Tension strengths/compression yield stresses decreased by about 25 %/45 % in radial, 9 %/42 % in tangential, and 32 % (compression) in longitudinal direction, respectively. These parameters increased with an increasing density. Based on the mechanical tests, Young’s modulus, tension strength and compression yield stress were derived as density- and moisture-dependent material model parameters. Shear modulus and shear strength were estimated by a theoretical approach. The experimental and modelling study was accompanied by a literature survey on characteristics of lime wood relevant for hygro-mechanical material modelling.

The Characteristics of Ancient Residence Wood from the Qing Dynasty in Yunnan Province

This study takes the wooden components of the different parts of the ancient buildings at the site of the Zhuangzishang Conference as the object of study, and investigates the deterioration state of the different wood components. To assess their degree of degradation, the wood anatomy, basic density (BD), maximum water content (MWC), cell wall major components, X-ray diffraction (XRD), infrared spectroscopy (IR), and thermogravimetry (TG) were used to compare the samples of new and old wood from the same species. The window (W) was identified by microscopic characterization as cypress (Cupressus sp.), the footing beam (FB) and the weatherboard (WB) as pine (Pinus spp.), the purlin (P) and the column (C) as Chinses fir (Cunninghamia spp.), and the floor (F) as spruce (Picea sp.). In terms of their physical properties, the old wood had a lower basic density of 2.58%–38.19%, a lower air-dry density of 2.87%–39.81%, and a higher maximum moisture content of 8.52%–41.38% compared to the reference wood. The degradation of the FB, which has been subjected to moisture and sunlight, and the P, which has been subjected to termite damage, was greater than that of their conspecifics. The integrated holocellulose of the ancient wood was 3.34%–16.48% less, and the hemicellulose was 1.6%–21.92% less compared to that of the reference wood, and the lignin was 1.32%–25.07% more. The XRD results showed that the crystallinity of the cellulose was greater in the different species of ancient wood compared to the control wood, which was caused by the decrease in the amorphous zones of the hemicellulose and cellulose in the ancient wood. The IR indicated that the degradation of cellulose and hemicellulose occurred in the old wood of all species, from the new lignin uptake peaks in the UV-exposed W, FB, and WB compared to the control timber. The pyrolytic behavior of the ancient and control timber is mainly related to the degradation of the tree species and the ancient wood holocellulose. These results show that the differences in the wooden components of the different parts of the ancient buildings at the Zhuangzishang Conference site are mainly related to the species of trees used in the components, and are secondly related to the location of the ancient wood members, which provides useful information for the protection and repair of the ancient buildings at the site.

Forestry control in the Brazilian Amazon III: anatomy of wood and charcoal of tree species from sustainable forest management

Summary The illegal harvest of timber and the subsequent production of charcoal have been contributing to the deforestation of the Brazilian Amazon and its degradation. Analysis of wood anatomy is a well-established tool used to detect illegally harvested wood and is commonly employed in the control of illegal forestry activities. This study aimed to contribute to a database used for the anatomical identification of wood and charcoal from tree species commonly harvested and marketed in the Amazon. The macro- and microscopic characteristics of wood and charcoal for 15 forest species were described. Characteristics that could be described in detail, such as vessel grouping, type of axial parenchyma, and in some cases, perforation plates and uniseriate rays, are fundamental to the identification of wood and charcoal that are illegally, or even legally, marketed. The study aids in the monitoring of the illegal marketing of wood and charcoal and will contribute to the construction of a database and reference collections that will be available for research, training, and use by forest managers, anatomists and anthracologists who study both wood and charcoal.

The physical, mechanical, and chemical properties of black cherry tree wood (Prunus serotina Ehrh.) and its susceptibility to fungal decomposition in areas where it is secondary and invasive: a case study in the Kampinos National Park (Poland)

The properties of black cherry mature wood (Prunus serotina Ehrh.) and its susceptibility to fungal decay were studied in the invaded range of the species on six trees aged between 39 and 47 years old growing in poor, acidic soils with varying levels of moisture and organic carbon and nitrogen content. Wood from trees that grew in wetter and richer soil had better physical properties. Of the 95 parameters analyzed, 80 showed significant differences in favor of this wood. These differences included wider rings that averaged 3.25 mm, a higher density of 662.71 kg/m3 at 12% humidity, and 1.5 times higher content of extractives. Gas chromatography with mass spectrometry revealed the presence of 44 extractives. Out of these, six had antifungal properties and were found in the wood of trees grown in richer soil, corresponding to 62.93% of the peaks area of all identified substances. Only three were found in trees grown in poorer soil, corresponding to 8.68% of the peaks area respectively. The wood of trees grown in more fertile soil was also less prone to fungal decay, which was generally low. Only Trametes versicolor caused a mass loss of more than 10% of the wood in both sites out of the four basidiomycete species tested. The results indicate that even slight variations in soil fertility and moisture can benefit black cherry, leading to differences in wood features and properties in its exotic range.

Unmanned Aerial Vehicle–Light Detection and Ranging-Based Individual Tree Segmentation in Eucalyptus spp. Forests: Performance and Sensitivity

As an emerging powerful tool for forest resource surveys, the unmanned aerial vehicle (UAV)-based light detection and ranging (LiDAR) sensors provide an efficient way to detect individual trees. Therefore, it is necessary to explore the most suitable individual tree segmentation algorithm and analyze the sensitivity of the parameter setting to determine the optimal parameters, especially for the Eucalyptus spp. forest, which is one of the most important hardwood plantations in the world. In the study, four methods were employed to segment individual Eucalyptus spp. plantations from normalized point cloud data and canopy height model generated from the original UAV-LiDAR data. And the parameter sensitivity of each segmentation method was analyzed to obtain the optimal parameter setting according to the extraction accuracy. The performance of the segmentation result was assessed by three indices including detection rate, precision, and overall correctness. The results indicated that the watershed algorithm performed better than other methods as the highest overall correctness (F = 0.761) was generated from this method. And the segmentation methods based on the canopy height model performed better than those based on normalized point cloud data. The detection rate and overall correctness of low-density plots were better than high-density plots, while the precision was reversed. Forest structures and individual wood characteristics are important factors influencing the parameter sensitivity. The performance of segmentation was improved by optimizing the key parameters of the different algorithms. With optimal parameters, different segmentation methods can be used for different types of Eucalyptus plots to achieve a satisfying performance. This study can be applied to accurate measurement and monitoring of Eucalyptus plantation.

Chestnut blight (Cryphonectria parasitica (Murr.) Barr) disease incidence and its effect on the morphological and anatomical features of Castanea sativa trees

AbstractSweet chestnut (Castanea sativa) is an ecologically and economically valuable tree species worldwide. Various pathogens, both endemic or introduced, cause severe damage or death to chestnut trees. Chestnut blight, caused by the fungus Cryphonectria parasitica, is one of the most devastating plant diseases known which influences chestnut trees in all major cultivation regions. The work presented here aimed to investigate how the incidence of chestnut blight varied between trees growing at two altitudes (200–400 m vs. 400–600 m) and to determine the impact of chestnut blight on tree‐ring width, morphology and anatomy of C. sativa trees. The incidence of C. parasitica infections was greater at 200–400 m than at 400–600 m. Greater stem diameters were found at 200–400 m than at 400–600 m. There were no differences in stem diameters and heights, however, between healthy and C. parasitica infected chestnut trees. The anatomical characteristics of wood were also compared between healthy and C. parasitica‐infected chestnut trees. Fibre cell traits (length/width, lumen width, lumen area) were higher in healthy trees than in C. parasitica‐diseased trees. Vessel diameters were greater in infected compared with healthy trees. Tree ring widths and wood anatomical characteristics therefore were significantly influenced by C. parasitica infections.

Influence of fertilization and water deficit on the density and anatomical characteristics of eucalyptus grandis wood

The expansion of plantations may be compromised by climate change, altering the frequency and intensity of precipitation. This study aimed to evaluate the influence of potassium and sodium fertilization and water deficit on the apparent density property and anatomical characteristics of Eucalyptus grandis wood. Six treatments varying in fertilization and rainfall incidence were evaluated. Apparent density testing was conducted via X-ray, while the anatomical features of fibers and vessels were examined through image analysis using a polarized light microscope. Cartography was also performed to map the density variation along the trunk in longitudinal and radial directions. Trees without fertilization exhibited higher apparent density, whereas those with partial rain exclusion displayed less homogeneous wood. Overall, treatments involving potassium and sodium showed no significant difference between them and resulted in a thinner secondary wall. The results indicate that water deficit and fertilization methods significantly impact wood properties.

Effects of physicochemical characteristics on natural durability of eucalypts woods to wood-decaying fungi

This study aimed to relate the biological resistance of seven eucalypt woods to wood-decaying fungi with physicochemical characteristics of wood. Two 12-year-old trees per species were randomly sampled, removing disks at 0 (base), diameter to breast height - DBH, 25, 50, 75, and 100% of the commercial height to determine the wood specific gravity. One basal log of 2.20 m of each wooden species was obtained for chemical analysis and biological tests with brown and white rot fungi (Gleophyllum trabeum, Rhodonia placenta, and Trametes versicolor). For these tests, wood samples were taken in two positions in the radial direction of the trunk in the pith-bark direction (median heartwood and transition region; containing heartwood and sapwood), and the relation between wood natural resistance and physicochemical characteristics was established. Wood specific gravity ranged of 0.51 g cm−3 to 0.73 g cm−3, total lignin of 27.34–32.18%, and holocellulose of 53.39–66.18, not being influenced by pith-bark direction. The extractive and ash contents were affected by the pith-bark direction, in which, in general, the transition region exhibited the highest values contents. The extractive showed a negative relation (−0.67) regarding the loss of mass caused by the fungus Rhodonia placenta. For the holocellulose content, it showed positive relations (0.61; 0.54) to the degradation by Rhodonia placenta and Gleophyllum trabeum, respectively. Independently of the analyzed wood and tested fungus, the median heartwood region was more resistant to wood decay fungi than the transition region.