Centrifugal Spinning Research Articles

High‐Performance Supercapacitor Electrodes Based on Porosity‐Controllable Carbon Paper by Centrifugal Spinning

Carbon paper is widely utilized in supercapacitors primarily for its notable attributes, including high specific surface area, commendable electrical conductivity, and excellent chemical stability. Then investigate the effect of carbon paper with different porosities as supercapacitor substrates on the electrochemical performance of electrodes. Meanwhile, tungsten oxide is grown on the surface of carbon paper using the hydrothermal method to test the electrochemical performance of the composite electrode. The prepared carbon paper and oxygen‐deficient tungsten oxide (WOx) composite electrode (CP@WOx) exhibit an area‐specific capacitance of 915.8 mF/cm² at a current density of 5 mA/cm². In addition, the electrode exhibits good cycling stability. After 20,000 cycles, the capacitance remains 104.1% of the original capacity at 50 mA/cm² current density. Solid‐state symmetric supercapacitors assembled using CP@WOx electrode exhibit excellent performance in terms of surface energy density of 6.25 µWh/cm2(at a power density of 0.6 mW/cm2) and maintain 100.4% of their original capacity after 7000 charge/discharge cycles. Relying on the higher productivity advantage of centrifugal spinning technology over electrostatic spinning technology and other preparation processes, this study develops a new way of thinking for the large‐scale production of composite electrode materials, which has more considerable potential for large‐scale development.

A coalescing filter with hybrid structure of oleophilic/oleophobic media by centrifugal spinning

A coalescing filter with hybrid structure of oleophilic/oleophobic media by centrifugal spinning

Electro–Centrifugal Spinning of Core–Sheath Composite Yarns with Micro/Nano Structures for Self–Powered Sensing

In recent years, triboelectric nanogenerators (TENGs) have garnered extensive attention in the realm of self-powered sensors due to their capability to harness low-frequency mechanical energy. Among these, textile-based triboelectric nanogenerator stands out as a pivotal platform for wearable sensing. Nevertheless, conventional approaches, such as directly coating triboelectric materials on fabrics, often compromise the inherent properties. In this study, we utilized our self-developed electro-centrifugal spinning equipment to continuously fabricate core-sheath yarns with micro/nano structures, resulting in the development of pocket-shaped fabric-based (PF) TENGs. This innovative design preserves the original softness and breathability of the fabric while delivering substantial electrical output owing to its layered structure and extensive specific surface area. PF–TENGs can accurately detect electrical output signals from various motion states. This electro–centrifugal spinning technology offers new research directions and sensing application prospects for self-powered smart textile development.

Processing and Properties of Polyhydroxyalkanoate/ZnO Nanocomposites: A Review of Their Potential as Sustainable Packaging Materials.

The escalating environmental concerns associated with conventional plastic packaging have accelerated the development of sustainable alternatives, making food packaging a focus area for innovation. Bioplastics, particularly polyhydroxyalkanoates (PHAs), have emerged as potential candidates due to their biobased origin, biodegradability, and biocompatibility. PHAs stand out for their good mechanical and medium gas permeability properties, making them promising materials for food packaging applications. In parallel, zinc oxide (ZnO) nanoparticles (NPs) have gained attention for their antimicrobial properties and ability to enhance the mechanical and barrier properties of (bio)polymers. This review aims to provide a comprehensive introduction to the research on PHA/ZnO nanocomposites. It starts with the importance and current challenges of food packaging, followed by a discussion on the opportunities of bioplastics and PHAs. Next, the synthesis, properties, and application areas of ZnO NPs are discussed to introduce their potential use in (bio)plastic food packaging. Early research on PHA/ZnO nanocomposites has focused on solvent-assisted production methods, whereas novel technologies can offer additional possibilities with regard to industrial upscaling, safer or cheaper processing, or more specific incorporation of ZnO NPs in the matrix or on the surface of PHA films or fibers. Here, the use of solvent casting, melt processing, electrospinning, centrifugal fiber spinning, miniemulsion encapsulation, and ultrasonic spray coating to produce PHA/ZnO nanocomposites is explained. Finally, an overview is given of the reported effects of ZnO NP incorporation on thermal, mechanical, gas barrier, UV barrier, and antimicrobial properties in ZnO nanocomposites based on poly(3-hydroxybutyrate), poly(3-hydroxybutyrate-co-3-hydroxyvalerate), and poly(3-hydroxybutyrate-co-3-hydroxyhexanoate). We conclude that the functionality of PHA materials can be improved by optimizing the ZnO incorporation process and the complex interplay between intrinsic ZnO NP properties, dispersion quality, matrix-filler interactions, and crystallinity. Further research regarding the antimicrobial efficiency and potential migration of ZnO NPs in food (simulants) and the End-of-Life will determine the market potential of PHA/ZnO nanocomposites as active packaging material.

Carbon fibers decorated with TiO2 nanoparticles for photocatalytic degradation of methylene blue dye

This report demonstrates the development of carbon fibers (CFs) decorated with TiO2 nanoparticles (NPs) as an efficient photocatalyst for the photocatalytic degradation of methylene blue (MB) as a model dye. Carbon fibers were produced by carbonization of polyacrylonitrile fibers, previously produced by centrifugal spinning. Subsequently, the CFs were decorated with TiO2 NPs (CFs@TiO2) by tailored soaking protocol using aqueous TiCl4 solution with different concentrations (0.025, 0.05, 0.1, and 0.2 M). SEM analyses revealed that soaking in TiCl4 produced a smooth, conformal, continuous TiO2 nanoparticulate coating with thickness increasing from 40.4 ± 21.2 to 257.9 ± 63.9 nm with increasing TiCl4 concentration. X-ray diffraction and Raman spectroscopy confirmed the anatase nature of TiO2. Photocatalytic decomposition rates of MB were assessed under UV light illumination for all CFs@TiO2 samples, and it was revealed that the lowest amount of TiO2 NP on C yielded the highest rates. The synergistic interaction between CFs and TiO2 NPs with a uniform morphology and a well-crystalline anatase structure, present in an optimal amount of fiber bodies, is the key reason for the remarkable photocatalytic performance. This work shows that C fibers decorated with an optimal amount of TiO2 NPs have a great potential as an effective photocatalytic material.

A biodegradable bi‐layer nano fibrous membrane fabricated by centrifugal spinning for active food packaging

AbstractTo solve the problem of cytotoxicity for most antimicrobial agents loaded in packaging materials, we developed a novel bi‐layer fibrous membrane by using centrifugal spinning, which of the outer layer was submicron native potato starch/polyvinyl alcohol (ST/PVA) composite fibers loaded with ZnO nanoparticles (ZnO NPs) for providing high antibacterial activity. The inner layer was nano‐based calcium alginate/polyethylene oxide (CA/PEO) fiber for providing excellent biocompatibility. The addition of ZnO caused the semicrystalline structures of ST/PVA fibers, while the CA/PEO fibers were shown semicrystalline structures due to the PEO. Fourier transform infrared indicated that posttreatment had not effect on the structures of ST/PVA/ZnO fiber, but the structure of CA/PEO fibers were affected by interaction between COO groups of alginate and Ca2+ ions. The results of mechanical property demonstrated that CA/PEO fibers showed highest stress of 3.83 ± 0.25 MPa and helpful for improving the stress of bi‐layer fibrous membrane. The obtained fibrous membrane had excellent antibacterial property with diameters of bacteriostatic zone against E. coli and S. aureus of 20.5 and 21.5 mm, respectively. On this basis, the shelf life of strawberry was improved up to 6th day by inhibit the growth of microorganisms, which indicated that the obtained fibrous membrane showed great potential for food packaging.

Advanced superhydrophobic polylactic acid fibers with high porosity and biodegradability for efficient solvent recovery

The conventional oil-absorbing materials utilized for addressing oil and organic solvent pollution are plagued by the issue of secondary pollution. In this study, biodegradable porous polylactic acid (PLA) fiber materials were prepared using centrifugal spinning technology, with PLA and polyvinyl butyral (PVB) as raw materials. PVB was utilized as a pore-forming agent to fabricate multi-layered porous PLA fiber materials. When the content of PVB in the spinning solution was 14 %, the porous PLA fibers exhibited the maximum specific surface area of 60.7 m2/g and a porosity of up to 85.4 %, interior of the fiber contained numerous mesopores. Additionally, the porous PLA fibers demonstrated excellent superhydrophobic oil absorption properties, with a water static contact angle of 137.8° and oil or organic solvent absorption capacities ranging from 10 to 17.7 g/g. Furthermore, porous PLA fiber materials exhibited outstanding biodegradability, with a degradation mass loss rate of 42.3–45.1 %. Therefore, superhydrophobic and oleophilic biomass-based PLA fiber materials prepared in centrifugal spinning show promising applications in the recovery of organic solvents and oily substances.

Oil Sorption Properties of Centrifugally Spun Polyisobutylene-Based Thermoplastic Elastomer Microfibers

Fiber-based sorbent materials are an essential part of containing oil spills, thus preventing ecological damage. Poly(styrene-b-isobutylene-b-styrene) thermoplastic elastomer fibers were successfully produced by centrifugal spinning. Scanning electron microscopy revealed that the fibers were bead free and smooth-surfaced, with an average fiber diameter of 5.9 ± 2.3 μm. Contact angle measurements proved the highly hydrophobic (water contact angle of 126.8 ± 6.4°) and highly oleophilic nature of the fiber mat. The sorption and retention capacities of the fiber mat were tested for various oils and benchmarked against polypropylene as the industry standard and polystyrene, which is widely used in the literature. The oil uptake of the fiber mat showed a strong correlation with the viscosity of the oil, resulting in sorption capacities of 10.1 ± 0.8 g/g for sunflower oil, 19.9 ± 2.1 g/g for motor oil, and 23.8 ± 1.8 g/g for gear oil. Oil–water separation tests were also conducted, resulting in ~100% oil removal. The thermoplastic elastomer fiber mat outperformed the industry standard; however, the polystyrene fiber mat demonstrated the best oil sorption performance.

Studying microbially induced corrosion on glass using ToF-SIMS.

Microbially induced corrosion (MIC) is an emerging topic that has huge environmental impacts, such as long-term evaluation of microbial interactions with radioactive waste glass, environmental cleanup and disposal of radioactive material, and weathering effects of microbes. Time-of-flight secondary ion mass spectrometry (ToF-SIMS), a powerful mass spectral imaging technique with high surface sensitivity, mass resolution, and mass accuracy, can be used to study biofilm effects on different substrates. Understanding how to prepare biofilms on MIC susceptible substrates is critical for proper analysis via ToF-SIMS. We present here a step-by-step protocol for preparing bacterial biofilms for ToF-SIMS analysis, comparing three biofilm preparation techniques: no desalination, centrifugal spinning (CS), and water submersion (WS). Comparisons of two desalinating methods, CS and WS, show a decrease in the media peaks up to 99% using CS and 55% using WS, respectively. Proper desalination methods also can increase biological signals by over four times for fatty acids using WS, for example. ToF-SIMS spectral results show chemical compositional changes of the glass exposed in a Paenibacillus polymyxa SCE2 biofilm, indicating its capability to probe microbiologically induced corrosion of solid surfaces. This represents the proper desalination technique to use without significantly altering biofilm structure and substrate for ToF-SIMS analysis. ToF-SIMS spectral results showed chemical compositional changes of the glass exposed by a Paenibacillus bacterial biofilm over 3-month inoculation. Possible MIC products include various phosphate phase molecules not observed in any control samples with the highest percent increases when experimental samples were compared with biofilm control samples.

Research on the process of preparing fiber filtration membrane by centrifugal blowing electrospinning technology

AbstractCurrently, the problem of air pollution is getting more and more serious, especially the pollution of tiny solid particles (PM, particulate matter) in the air, which poses a great challenge to the environment and human health. Therefore, it is particularly important to develop air filtration materials with high filtration efficiency and low resistance to meet this challenge. In this study, we propose to prepare air filtration membranes by centrifugal jet electrospinning technology, design multifactorial orthogonal coupling experiments, and investigate the effects of key process parameters of centrifugal jet electrostatic spinning, including solution concentration, airflow rate, rotational speed, and voltage, on the fiber diameter and uniformity by applying the polar analysis of variance and analysis of variance. PAN‐BaTiO3 electret nanofiber filtration membranes with high efficiency and low resistance were prepared by combining the optimized process of centrifugal blowing electrospinning. Various characterization methods (tensile test, water contact angle test, surface charge test, filtration test) were used to evaluate the effect of different BaTiO3 electret contents (0%, 0.1%, 0.5%, 1%) on the comprehensive performance of the filtration membranes, and the electret filtration efficiency of the electret filtration membranes prepared by the present process reached as high as 96.56% with a pressure drop of 29 Pa.

Characterization of Fibers Prepared by Centrifugal Spinning from Biotechnologically Derived Chicken Gelatin.

The application of biopolymer-based materials is increasing due to better sustainability and environmental protection properties. Gelatin fibers have a specific surface and high porosity, which is why their use in medicine and the food industry is being researched. This article explores the potential of centrifugal spinning to produce gelatin fibers. Gelatin for fiber preparation was obtained from a non-traditional source of collagen (chicken by-products) using a unique enzymatic process. The fiber quality was compared with those prepared from gelatins produced from traditional collagen tissues (porcine, bovine). The results showed that fibers cross-linked with glutaraldehyde vapor preserved their structure even in contact with water. Using a cross-linker controlled swelling ability and solubility while maintaining the fiber structure. On the contrary, uncross-linked gelatin fibers were water soluble due to a high surface-to-volume ratio, facilitating water penetration and dissolution. Scanning electron microscopy (SEM) provided a clearer picture of the morphology of gelatin fibers obtained by centrifugal spinning. Differences in the amount of bonding depending on the raw material used and the presence of a cross-linker were analyzed using Fourier transform infrared spectroscopy (FTIR). The overall results showed that chicken gelatin is a suitable alternative to gelatins from traditional sources and can be used for preparing food and pharmaceutical packaging and coatings, fibers, or bioprinting of 3D matrices.

Aerogel Fibers Made via Generic Sol‐Gel Centrifugal Spinning Strategy Enable Dynamic Removal of Volatile Organic Compounds From High‐Flux Gas

AbstractAerogels with ultrahigh porosity and large specific surface area have demonstrated great potential for capturing volatile organic compounds (VOCs). Especially, aerogel fiber aggregates with macropores formed by overlapping aerogel fibers and mesopores in the aerogel fibers might realize fast sorption kinetics and high sorption capacity simultaneously. However, how to develop fast fabrication and large‐scale production of aerogel fibers remains a challenge. Herein, a generic sol‐gel centrifugal spinning (SCS) strategy with a spinning rate capable of reaching 700 m min−1 is developed for producing aerogel fibers. The representative SCS aerogel fiber made from aramid nanofiber (ANF) dispersion exhibits a large specific surface area (313 m2 g−1) and high tensile strength (12.48 MPa). The SCS strategy is further applied to fabricate various kinds of aerogel fibers, including sodium alginate, cellulose, and chitosan. The ANF aerogel fiber aggregates exhibit superior VOC adsorption capacity of 438.0 mg g−1 under an ultrafast gas flux of 3.8 × 104 L m−2 h−1, which also has satisfactory cyclic stability. This work not only develops a powerful and generic strategy for fabricating aerogel fibers in large scale, but also provides inspiration for applying these SCS aerogel fibers in dynamic removal of VOCs and other environmental protection fields.

High-performance cellulose-based nanostructured carbons for rechargeable batteries

Binder-free, highly porous carbon nanofibers (CNFs) with novel sponge-like pore structures were synthesized for the first time via centrifugal spinning of cellulose-based polymers, and SnO2 was introduced to improve the electrochemical performance. Cellulose-based binder-free centrifugally spun carbon-coated SnO2/carbon nanofibers (C@SnO2/CNFs) were employed as anodes in Na-ion batteries. Owing to their highly porous morphology with novel sponge-like pore structures and SnO2 nanoparticles providing rapid Na-ion transport, better electrolyte accessibility, and good mechanical strength, the C@SnO2/CNFs showed outstanding electrochemical performance, with a high reversible capacity of 660 mAh/g at 50 mA/g, high rate capability, and excellent cycling performance. The specific capacity of C@SnO2/CNFs was approximately 390 mAh/g after 2000 cycles at 0.2 A/g. These results prove that the combination of centrifugal spinning, carbon coating, and heat treatment is a promising and sustainable approach for creating cellulose-based carbon nanostructures with highly porous structures that can be used to synthesize high-performance electrodes for energy storage systems.

Facile preparation of alkali metal‐modified hollow nanotubular manganese‐based oxide catalysts and their excellent catalytic soot combustion performance

AbstractThe soot emitted during the operation of diesel engine exhaust seriously threatens the human health and environment, so treating diesel engine exhaust is critical. At present, the most effective method for eliminating soot particles is post‐treatment technology. Preparation of economically viable and highly active soot combustion catalysts is a pivotal element of post‐treatment technology. In this study, different single‐metal oxide catalysts with fibrous structures and alkali metal‐modified hollow nanotubular Mn‐based oxide catalysts were synthesized using centrifugal spinning method. Activity evaluation results showed that the manganese oxide catalyst has the best catalytic activity among the prepared single‐metal oxide catalysts. Further research on alkali metal modification showed that doping alkali metals is beneficial for improving the oxidation state of manganese and generating a large number of reactive oxygen species. Combined with the structural effect brought by the hollow nanotube structure, the alkali metal‐modified Mn‐based oxide catalysts exhibit superior catalytic performance. Among them, the Cs‐modified Mn‐based oxide catalyst exhibits the best catalytic performance because of its rich active oxygen species, excellent NO oxidation ability, abundant Mn4+ ions (Mn4+/Mnn+ = 64.78%), and good redox ability. The T10, T50, T90, and CO2 selectivity of the Cs‐modified Mn‐based oxide catalyst were 267°C, 324°C, 360°C, and 97.8%, respectively.

Development of high sensitivity composite sensors for proprioceptive applications

This study describes the fabrication of extremely sensitive piezoresistive composite sensors designed to detect human motion and speech. Starting out, a solution of thermoplastic polyurethane (TPU) was formed in dimethyl formamide (DMF) with a concentration of 35 % weight to volume. The solution was subsequently spun using a custom-built centrifugal spinning setup to produce TPU fibers. Following their fabrication through spinning, TPU fibers were immersed in a solution of carbon nanoparticles (CNPs) dispersed in tetra hydrofuran (THF), having a concentration of 25 %w/v, for dip coating TPU fibers with CNPs. This resulted in the formation of highly piezoresistive fibers having strain sensing capability. These fibers were then spun into the form of a yarn and tested as a strain sensor for proprioceptive applications. The composite sensors exhibited exceptional repeatability in tests involving continuous stretching and relaxing for more than 5000 cycles. The composite strain sensor demonstrated remarkable extensibility as well. The composite strain sensor was attached to different body parts such as the elbow, knees, fingers, and ankles to detect and track motion. It was found that the sensor could measure and track the angle, position, and frequency of motion in all of these scenarios. The sensor's remarkable sensitivity allowed it to detect different spoken words and letters, in addition to recognizing the action of swallowing in humans. The results show that the newly developed composite strain sensors are suitable for proprioceptive and speech recognition applications in soft robotics, wearable devices, and human-machine interactions.

Centrifugally spun hydroxyapatite/carbon composite nanofiber scaffolds for bone tissue engineering

In recent years, advancements in tissue engineering have demonstrated the potential to expedite bone matrix formation, leading to shorter recovery times and decreased clinical challenges compared to conventional methods. Therefore, this study aims to develop composite carbon nanofibers (CNFs) integrated with nano-hydroxyapatite (nHA) particles as scaffolds for bone tissue engineering applications. A key strategy in achieving this objective involves harnessing nanofibrous structures, which offer a high surface area, coupled with nHA particles expected to accelerate bone regeneration and enhance biological activity. To realize this, polyacrylonitrile (PAN)/nHA nanofibers were fabricated using the centrifugal spinning (C-Spin) technique and subsequently carbonized to yield CNF/nHA composite structures. Scanning Electron Microscopy (SEM) confirmed C-Spin as a suitable method for PAN and CNF nanofiber production, with nHA particles uniformly dispersed throughout the nanofibrous structure. Carbonization resulted in reduced fiber diameter due to thermal decomposition and shrinkage of PAN molecules during the process. Furthermore, the incorporation of nHA particles into PAN lowered the stabilization temperature (by 5 °C–20 °C). Tensile tests revealed that PAN samples experienced an approximately 80% increase in ultimate tensile strength and a 187% increase in modulus with a 5 wt.% nHA loading. However, following carbonization, CNF samples exhibited a 50% decrease in strength compared to PAN samples. Additionally, the addition of nHA into CNF improved the graphitic structure. The incorporation of nHA particles into the spinning solution represents a viable strategy for enhancing CNF bioactivity.

Nanostructured Carbon Fibres (NCF): Fabrication and Application in Supercapacitor Electrode.

A facile interconnected nanofibre electrode material derived from polybenzimidazol (PBI) was fabricated for a supercapacitor using a centrifugal spinning technique. The PBI solution in a mixture of dimethyl acetamide (DMA) and N, N-dimethylformamide (DMF) was electrospun to an interconnection of fine nanofibres. The as-prepared material was characterised by using various techniques, which include scanning electron microscopy (SEM), X-ray diffractometry (XRD), Raman, X-ray photoelectron spectroscopy (XPS), and Brunauer-Emmett-Teller (BET) among others. The specific surface area of the interconnected NCF material was noticed to be around 49 m2 g-1. Electrochemical properties of the material prepared as a single-electrode are methodically studied by adopting cyclic voltammetry, electrochemical impedance spectroscopy, and constant-current charge-discharge techniques. A maximum specific capacitance of 78.4 F g-1 was observed for the electrode at a specific current of 0.5 A g-1 in a 2.5 M KNO3 solution. The electrode could also retain 96.7% of its initial capacitance after a 5000 charge-discharge cycles at 5 A g-1. The observed capacitance and good cycling stability of the electrode are supported by its specific surface area, pore volume, and conductivity. The results obtained for this material indicate its potential as suitable candidate electrode for supercapacitor application.

Preparation of CNT/CNF/PDMS/TPU Nanofiber-Based Conductive Films Based on Centrifugal Spinning Method for Strain Sensors.

Flexible conductive films are a key component of strain sensors, and their performance directly affects the overall quality of the sensor. However, existing flexible conductive films struggle to maintain high conductivity while simultaneously ensuring excellent flexibility, hydrophobicity, and corrosion resistance, thereby limiting their use in harsh environments. In this paper, a novel method is proposed to fabricate flexible conductive films via centrifugal spinning to generate thermoplastic polyurethane (TPU) nanofiber substrates by employing carbon nanotubes (CNTs) and carbon nanofibers (CNFs) as conductive fillers. These fillers are anchored to the nanofibers through ultrasonic dispersion and impregnation techniques and subsequently modified with polydimethylsiloxane (PDMS). This study focuses on the effect of different ratios of CNTs to CNFs on the film properties. Research demonstrated that at a 1:1 ratio of CNTs to CNFs, with TPU at a 20% concentration and PDMS solution at 2 wt%, the conductive films crafted from these blended fillers exhibited outstanding performance, characterized by electrical conductivity (31.4 S/m), elongation at break (217.5%), and tensile cycling stability (800 cycles at 20% strain). Furthermore, the nanofiber-based conductive films were tested by attaching them to various human body parts. The tests demonstrated that these films effectively respond to motion changes at the wrist, elbow joints, and chest cavity, underscoring their potential as core components in strain sensors.

Fabrication and evaluation of centrifugal spun Miconazole-loaded sugar-based fibers

Oral candidiasis is considered a very common infection in the oral cavity caused by Candida albicans (C. albicans). Miconazole is considered to be a very effective drug against many fungal infections but suffers from water insolubility and an unpleasant taste. Therefore, this study aims to prepare miconazole encapsulated into a sugar-based fibrous system composed of sucrose as the main component, along with polyvinylpyrrolidone (PVP) as a stabilizer, and miconazole using centrifugal spinning and to assess its antifungal activity in in vitro and in vivo mice models. The data showed that the miconazole-loaded fibers had a diameter of 6.6 ± 2.5 μm, an encapsulation efficiency % of 52 ± 4.5 %, a drug loading of 52 ± 4.5 μg/mg and full and rapid drug release after 4 h. The in vitro antifungal assessment exhibited that the miconazole-loaded fibers have a comparable antifungal activity to that of the positive control miconazole against two C. albicans strains. The in vivo mice oral candidiasis model demonstrated the ability of the miconazole-loaded fibers to inhibit C. albicans similarly to the commercially available product after 7 days of the treatment. Therefore, the miconazole-loaded fibers can be used as a potential alternative medication for oral candidiasis owing to its anti-Candida activity and its presence as a cotton-candy-like dosage form that would improve the children's acceptability and adherence. Further in vivo testing and long-term stability are required to ensure the safety, efficacy, and stability of this dosage form before its clinical application.

Spinning the Future: The Convergence of Nanofiber Technologies and Yarn Fabrication.

The rapid advancement in nanofiber technologies has revolutionized the domain of yarn materials, marking a significant leap in textile technology. This review dissects the nexus between cutting-edge nanofiber technologies and yarn manufacturing, aiming to illuminate the pathway toward engineering advanced textiles with unparalleled functionality. It first discusses the fundamentals of nanofiber assemblies and spinning techniques, primarily focusing on electrospinning, centrifugal spinning, and blow spinning. Additionally, the study delves into integrating nanofiber spinning technologies with traditional and modern yarn fabrication principles, elucidating the design principles that underlie the creation of yarns incorporating nanofibers. Twisting technologies are explored to examine how they can be optimized and adapted for incorporating nanofibers, thus enabling the production of innovative nanofiber-based yarns. Special attention is given to scalable strategies like centrifugal and blow spinning, which are spotlighted for their efficiency and scalability in fabricating nanofiber yarns. This review further analyses recently developed nanofiber yarn applications, including wearable sensors, biomedical devices, moisture management textiles, and energy harvesting and storage devices. We finally present a forward-looking perspective to address unresolved issues in nanofiber-based yarn technologies.