Cathode Material For Batteries Research Articles

Dual Modification Strategy for Enhanced Cycling and Rate Performance of Ni-Rich Cathode Materials in Lithium-Ion Batteries.

A great challenge in the commercialization process of layered Ni-rich cathode material LiNixCoyMn1-x-yO2 (NCM, x ≥ 80%) for lithium-ion batteries is the surface instability, which is exacerbated by the increase in nickel content. The high surface alkalinity and unavoidable cathode/electrolyte interface side reactions result in significant decrease for the capacity of NCM material. Surface coating and doping are common and effective ways to improve the electrochemical performance of Ni-rich cathode material. In this study, an in situ reaction is induced on the surface of secondary particles of NCM material to construct a stable lithium sulfate coating, while achieving sulfur doping in the near surface region. The synergistic modification of lithium sulfate coating and lattice sulfur doping significantly reduced the content of harmful residual lithium compounds (RLCs) on the surface of NCM material, suppressed the side reactions between the cathode material surface and electrolyte and the degradation of surface structure of the NCM material, effectively improved the rate capability and cycling stability of the NCM material.

Theoretical study on the effect of shear deformation on WSe2 as a cathode material for calcium ion batteries

AbstractIn this paper, the first‐principles method is used to calculate the electronic structure of the intrinsic WSe2 system and the Ca adsorbed WSe2 system under shear deformation, and the diffusion barrier of Ca on WSe2 is studied in depth. The results show that shear deformation can effectively reduce the band gap of WSe2 system, and shear deformation can easily lead to the transition from semiconductor properties to metal properties. The adsorption of Ca leads to the change of the band structure of WSe2. The contribution of Ca‐d electrons leads to an increase in the peak in the range of 3–6 eV. The shear deformation reduces the diffusion barrier of Ca on the WSe2 surface. This paper provides an improvement method for the application of WSe2 in the field of battery.

A Unique Wide-Spacing Fence-Type Superstructure for Robust High-Voltage O3-Type Sodium Layered Cathode.

Enhancing the energy density of layered oxide cathode materials is of great significance for realizing high-performance sodium-ion batteries and promoting their commercial application. Lattice oxygen redox at high voltage usually enables a high capacity and energy density. But the structural degradation, severe voltage decay, and the resultant poor cycling performance caused by irreversible oxygen release seriously restrict the practical application. Herein we introduce a novel fence-type superstructure (2a × 3a type supercell) into O3-type layered cathode material Na0.9Li0.1Ni0.3Mn0.3Ti0.3O2 and achieve a stable cycling performance at a high voltage of 4.4 V. The fence-type superstructure effectively inhibits the formation of the vacancy clusters resulting from out-of-plane Li migration and in-plane transition metal migration at high voltage due to the wide d-spacing, thereby significantly reducing the irreversible release of lattice oxygen and greatly stabilizing the crystal structure. The cathode exhibits a high energy density of 545 Wh kg-1, a high rate capability (112.8 mAh g-1 at 5C) and a high cycling stability (85.8%@200 cycles with a high initial capacity of 148.6 mAh g-1 at 1C) accompanied by negligible voltage attenuation (98.5%@200 cycles). This strategy provides a distinct spacing effect of superstructure to design stable high-voltage layered cathode materials for Na-ion batteries.

Engineering interleaved large and small Na4MnV(PO4)3@NC microspheres cathode towards high performance sodium ion batteries

The booming consumption of energy storage devices spontaneously accelerates the urgent development of robust cathode materials for sodium-ion batteries (SIBs). In view of this, the sodium superionic conductor Na4MnV(PO4)3 (NMVP), with considerable energy density of 425 Wh kg−1, has become the focus in SIB research. Despite this, the performance of NMVP is substantially compromised by Jahn-Teller distortion of Mn3+ ions in conjunction with inherently limited electronic conductivity. In order to address this limitation, this study introduces a series of N-doped carbon (NC) coated NMVP materials with interleaved large and small microsphere morphology. Of particular note, the optimized NMVP-NC2 shows the most excellent performance, maintaining a capacity of 65.7 mAh g−1 at 5C over 500 cycles. A full cell configuration employing an NMVP-NC2 cathode and a commercial hard carbon (HC) anode manifests commendable circular stability with a capacity of 80.7 mAh g−1 underneath 100 cycles at 1C, with an impressive 95.3 % capacity preservation. This distinctive architecture imparts the materials with a high tap density and a relatively low surface area, which is beneficial to the industrial employment. In addition, density functional theory (DFT) calculations indicate that the NC regulation significantly narrows the NMVP's bandgap and facilitates electron transfer, thereby accelerating electron/ion transport kinetics. The NC coating approach combined with large-scale spray drying tactic in this work offers a clear strategy to industrialize NMVP cathode towards high-performance SIBs.

Investigation of cation doping on the structure and electrochemical properties of K0.5MnO2 cathode materials based on first-principles calculation

In an effort to find high-energy-density and high-mobility cathode material for K-Ion batteries, this paper presents a systematic study of multiple doping concentrations of P3-type K0.5Mn1-xMxO2 (M = Fe, Ti, and Cu) materials using first-principles approach. The most thermodynamically stable phase of each material is predicted by the formation of mixing enthalpy, and the optimal doping concentration of each doping element is screened. It is found that the redox activity of K0.5Mn1-xMxO2 is derived from the anion redox of O2−/O1− during depotassium. At the same time, doped Mn-based cathode materials have the characteristics of large capacity, stable structure, good thermal stability and small diffusion energy barrier. Among them, Fe doping will promote the charge compensation of O 2p-electrons in the intercalation process and reduce the Jahn-Teller distortion caused by Mn3+ (ratio < 46.67 %). Ti doping can improve the lattice stability of O, inhibit the precipitation reaction of oxygen, make TiO more covalent, and reduce the structural change during depotassium. Therefore, the overall thermal stability of the material is improved. Cu doping reduces the diffusion barrier of the material (0.54 eV). Through the basic understanding of the redox reaction mechanism in K0.5Mn1-xMxO2, the work of this paper lays a foundation for the rational design of high-performance K-ion batteries.

Rational Regulation of Optimal Oxygen Vacancy Concentrations on VO2 for Superior Aqueous Zinc-Ion Battery Cathodes.

VO2 with its special tunnel structure and high theoretical capacity is an ideal candidate for cathode materials for aqueous zinc-ion batteries (ZIBs). However, the slow kinetics and structural instability due to the strong electrostatic interactions between the host structure of VO2 and Zn2+ hinder its application. Defect engineering is a well-recognized strategy for improving the intrinsic ion-electron dynamics and structural stability of this material. However, the preparation of oxygen vacancies poses significant difficulties, and it is challenging to control their concentration effectively. Excessive or insufficient vacancy concentration can have a negative effect on the cathode material. Herein, we propose electrode materials with controlled oxygen vacancies prepared in situ on carbon nanofibers (CNF) by a simple, one-step hydrothermal process (Ov-VO2@CNF). This method can balance the adsorption energy and migration energy barrier easily, and we maximized the adsorption energy of Zn2+ while minimizing the adsorption energy barrier. Notably, the Ov2-VO2@CNF electrode delivered a high specific capacity (over 450 mAh g-1 at 0.1 A g-1) and excellent cycle stability (318 mAh g-1 at 5 A g-1 capacity after 2000 cycles with a capacity retention of 85%). This rational design of precisely regulated defect engineering provides a way to obtain advanced electrode materials with excellent comprehensive properties.

Electrochemical Behaviors and Doping Rules of NaRhO2 Cathode Materials for Sodium-Ion Batteries.

Sodium-ion batteries (SIBs) have great advantages for energy storage and conversion due to their low cost and large storage capacity. Currently, NaRhO2 is used as an electrode material for sodium-ion batteries. Doping first- and second-row transition metals has been carried out to comprehensively assess NaRhO2 as a cathode material. The geometric and electronic structures and electrochemical and doping behaviors of NaRhO2 cathode materials for SIBs have been investigated using density functional theory calculations. The results show that the bond lengths of Rh-O in NaRhO2 decrease during sodium deintercalation. The band gap of NaRhO2 with sodium extraction gradually reduces. The density of states of NaxRhO2 shows that the interaction between the Rh-4d and O-2p orbitals increases and the orbitals shift toward the right. The average intercalation voltage of NaxRhO2 cathode material increased from 2.7 to 3.9 eV. After doping with first- and second-row transition metal elements from Sc to Zn and Y to Cd, the changes in the band gaps of the doped NaRhO2 materials exhibit a W-type rule. In contrast, their magnetic moments show a reverse W-type rule. These findings on the pristine and doped NaRhO2 can provide theoretical guidance for the preparation of novel electrode materials suitable for sodium-ion batteries.

Unveiling the role of fluorinated interface on anionic redox chemistry in Li-rich layered oxide cathode materials towards high-energy Li metal batteries

The utilization of Lithium-rich materials (LR) with oxygen anionic redox (OAR) activity as cathode materials in Li metal batteries has gradually emerged as a prevailing trend in designing high-specific energy batteries. However, the interface design of LR and its influence mechanism on anionic redox chemistry are still ambiguous. Herein, in-situ interface engineering with an LiF-rich cathode-electrolyte interface (CEI) using all-fluorinated electrolyte was proposed and the role of the CEI on OAR was clarified. The shielding effect on high-valence oxygen ions is revealed that the dense, uniform, thin, and robust LiF-rich CEI protects high-valence oxygen ions from the electrolyte, inhibits electrolyte decomposition and interface thickening, and ameliorates structural degradation and oxygen loss of LR. And a more critical effect of CEI on the OAR process is demonstrated that the LiF-rich CEI layer prevents molecular oxygen in the bulk from escaping into the electrolyte as O2 gas and makes the oxidized oxygen exists more in the form of peroxo-like oxygen dimer O2n−. Besides the stabilization of OAR in the cathode side, the all-fluorinated electrolyte along with its enhancement in the Li anode enable high safety, excellent cycling stability, and fast charging performance for high energy lithium metal batteries.

Effect of pre-inserted monovalent cations on vanadium-based cathode materials for rechargeable aqueous zinc-ion batteries

Understanding the effect of pre-inserted cations in vanadium-based from a comprehensive perspective plays a vital role in exploring novel cathode materials for Zn-ion storage. In this work, we provide a study of monovalent cations (i.e., Na+, K+, and NH4+) on the Zn2+ storage behaviors of proton-substituted vanadates (i.e., NaVO, KVO, and NH4VO), revealing the intrinsic property (e.g., hydration capacity, bonding strength) of monovalent ions has a significant impact on the amount of pre-inserted cations and crystal water in stacked V–O layers, as well as the morphology of the obtained products, and the structural evolution during the activated process. Due to the enhancement of the ion-diffusion kinetics and stronger capacitance properties from the synergistic effect by pre-inserted Na+ ions and crystal water, the NaVO cathode exhibits superior rate performance and better energy efficiency (60.87 % at 10 A g−1), delivers a high specific capacity of 427.0 mAh g−1 at 0.2 A g−1 and retains 74.3 % of capacity after 1900 cycles at 2 A g−1. Moreover, the correlation between the pre-inserted cations in the cathode and the issues (e.g., side-products and dendrites) of the Zn anode has been revealed, providing new insight into designing high-performance cathodes for Zn ion batteries.

Effect of Mo6+ induced valence changes of transition metal ions in Mn-rich layered cathode materials on electrochemical performance

Layered cathode materials for lithium-ion batteries have been extensively investigated; however, comparatively scant attention has been paid to Mn-rich layered cathode materials. Herein, LiNi0.5Mn0.5O2 cathode materials are doped to investigate the effect of doping elements on the electrochemical properties of Mn-rich layered cathodes. XRD (X-ray diffraction), XPS (X-ray photoelectron spectroscopy), and SQUID (superconducting quantum interference device) results reveal that Mo doping affects the electrochemical properties of the cathode materials by changing the valence state of transition metal ions. Due to the Mo6+ ions doping, a large proportion of Mn3+ ions present in LiNi0.5Mn0.5O2 were converted to Mn4+ ions, which alleviated the Jahn-Teller effect and reduced the elongated Mn-O octahedra, thus increasing the Li layer spacing and facilitating Li+ diffusion. Therefore, 1 % Mo-doped cathode exhibits a significantly improved Li-ion diffusion coefficient and superior rate performance with a specific discharge capacity of 103 mAh·g−1 at 5C. Meanwhile, the cathode materials significantly improve cycling performance due to the reduction in the amount of Mn3+. The current study provides guidelines for the modification of Mn-rich layered cathodes in the future.

Design of Coatings for Sulfur-Based Cathode Materials in Lithium-Sulfur Batteries: A review.

Lithium-sulfur batteries (LSBs) are considered next-generation energy storage and conversion solutions owing to their high theoretical specific capacity and the high abundance/low-cost of sulfur-based cathode materials. However, LSBs still encounter significant challenges, including the low conductivities of sulfur-based materials, severe volumetric expansion of sulfur during the discharge process, and the persistent "shuttle effect" of polysulfides. In recent years, a tremendous amount of research has been conducted to address the above challenges by developing coating and compositing materials and corresponding fabrication strategies for sulfur-based cathode materials. In this study, the surface coating, compositing materials, and fabrication methodologies of LSB cathodes are comprehensively reviewed in terms of advanced materials, structure/component characterization, functional mechanisms, and performance validation. Some technical challenges are analyzed in detail, and possible future research directions are proposed to overcome the challenges toward practical applications of lithium-sulfur batteries.

Synthesis, intercalation reactions, and electrochemical studies for VO2/PEO/Chitosan

VO2 obtained by hydrothermal synthesis from V2O5 was used as a matrix to obtain hybrid compounds containing different proportions of polyethylene oxide and chitosan. The XRD results demonstrate that monoclinic VO2 was obtained, and hybrid compounds showed variation in the displacement of the lamella peak, indicating an intercalation of polymers into the matrix. The stretching and vibration bands show a variation towards higher wavelength values of the hybrid compounds, which indicates that the intercalation of the polymers occurred into the matrix. The UV–Vis spectra show the absorptions that can be attributed to the transitions of each material. Absorption in the visible region decreases for hybrid compounds in relation to VO2. The hybrid compounds presented lower bandgap values compared to VO2. From cyclic voltammetry, it was possible to observe anodic and cathodic peaks linked to the redox process of the VIV/VIII pair for both VO2 and VO2/polymers, which is derived from the insertion/disinsertion process of lithium ions, where the hybrid compound presented a different voltammetric profile compared to VO2. The total charge curves as a function of the number of cycles demonstrate better cycling stability and a greater total charge of the hybrid compounds compared to VO2. These results demonstrate that hybrid compounds have potential as cathode materials for lithium-ion batteries.

Coordination engineering for iron-based hexacyanoferrate as a high-stability cathode for sodium-ion batteries

Iron-based hexacyanoferrate (Fe-HCF) are promising cathode materials for sodium-ion batteries (SIBs) due to their unique open-channel structure that facilitates fast ion transport and framework stability. However, practical implementation of SIBs has been hindered by low initial Coulombic efficiency (ICE), poor rate performance, and short lifespan. Herein, we report a coordination engineering to synthesize sodium-rich Fe-HCF as cathodes for SIBs through a uniquely designed 10-kg-scale chemical reactor. Our study systematically investigated the relationship between coordination surroundings and the electrochemical behavior. Building on this understanding, the cathode delivered a reversible capacity of 99.3 mAh g-1 at 5 C (1 C = 100 mA g-1), exceptional rate capability (51 mAh g-1 even at 100 C), long lifespan (over 15,000 times at 50 C), and a high ICE of 92.7%. A full cell comprising the Fe-HCF cathode and hard carbon (HC) anode exhibited an impressive cyclic stability with a high-capacity retention rate of 98.3% over 1,000 cycles. Meanwhile, this material can be readily scaled to the practical levels of yield. The findings underscore the potential of Fe-HCF as cathodes for SIBs and highlight the significance of controlling nucleation and morphology through coordination engineering for a sustainable energy storage system.

A Fundamental Correlative Spectroscopic Study on Li1‐xNiO2 and NaNiO2

AbstractThe intricate relationship between local atomic arrangements and electronic states significantly influences the electrochemical properties of Li‐ion battery cathode materials. Despite decades of investigation, a consensus regarding the local atomic and electronic structure of LiNiO2 remains elusive. This ambiguity stems from the potential distortion of Ni sites, either via Jahn‐Teller (JT) distortion or bond disproportionation (BD), complicating the understanding of the charge compensation mechanism involving Ni and O. This study compares the structures of LiNiO2 and NaNiO2, a JT system, using an innovative approach that integrates bulk spectroscopy techniques on standardized interoperable samples for enhanced reliability. While X‐r and theoretical calculations fail to differentiate between the proposed scenarios, Raman spectroscopy highlights local structural distinctions between monoclinic NaNiO2 and rhombohedral LiNiO2. HAXPES confirms various formal oxidation states for Ni, supported by RIXS data indicating 3d8 states, emphasizing negative charge transfer from Ni and some bond disproportionation in LiNiO2. Regarding charge compensation, XRS and RIXS suggest oxygen hole involvement in redox activity, whereas Raman spectroscopy does not detect molecular oxygen. This comprehensive spectroscopic analysis highlights the importance of correlative characterization workflows in elucidating complex structural‐electrochemical relationships.

Anionic-surfactant-assisted synthesis of Ni0.8Co0.1Mn0.1(OH)2 as precursors of high-performance cathode materials for lithium-ion batteries

A facilitated anionic-surfactant-assisted method is developed to synthesize hierarchical microstructure Ni0.8Co0.1Mn0.1(OH)2 precursors. The anionic surfactant β-styrylphosphonic acid could directionally regulate the growth and the arrangement of the precursor nanosheets, where the primary nanosheets could maintain layered growth and ordered arrangement. The cathode material of the LiNi0.8Co0.1Mn0.1O2 synthesized from the above precursors exhibits best electrochemical performances and its capacity retention rates could reach 93 % (164.5 mAh g−1) after 100 cycles and 84.3 % (149.0 mAh g−1) after 300 cycles. Meanwhile, the detailed atomic arrangements on the crystal facets of cathodes are investigated both via first-principles calculations and transmission electron microscopy (TEM) analysis, and this research reveals that the crystal facet structures of cathode materials determine the electrochemical properties significantly.

Imaging inter - and intra-particle features in crystalline cathode materials for Li-ion batteries using nano-focused beam techniques at 4th generation synchrotron sources

Imaging inter - and intra-particle features in crystalline cathode materials for Li-ion batteries using nano-focused beam techniques at 4th generation synchrotron sources

Spin Symmetry Breaking-Induced Hubbard Gap Near-Closure in N-Coordinated MnO2 for Enhanced Aqueous Zinc-Ion Battery Performance.

Transition metal oxides (TMOs) are promising cathode materials for aqueous zinc ion batteries (ZIBs), however, their performance is hindered by a substantial Hubbard gap, which limits electron transfer and battery cyclability. Addressing this, we introduce a heteroatom coordination approach, using triethanolamine to induce axial N coordination on Mn centers in MnO2, yielding N-coordinated MnO2 (TEAMO). This approach leverages the change of electronegativity disparity between Mn and ligands (O and N) to disrupt spin symmetry and augment spin polarization. This enhancement leads to the closure of the Hubbard gap, primarily driven by the intensified occupancy of the Mn eg orbitals. The resultant TEAMO exhibit a significant increase in storage capacity, reaching 351 mAh g-1 at 0.1 A g-1. Our findings suggest a viable strategy for optimizing the electronic structure of TMO cathodes, enhancing the potential of ZIBs in energy storage technology.

Microwave-assisted synthesis of highly uniform Prussian Blue@Carbon cathode materials for sodium-ion batteries

Prussian blue (PB) and its analogues (PBAs) as cathode material for sodium-ion batteries suffer from poor cycling stability because of crystal defects and sluggish ion diffusion kinetics. Composite with carbon materials is an effective solution to alleviate this problem. However, this is typically achieved through simple physical mixing or encapsulation, which relies heavily on the compatibility between carbon and PB, often resulting in composites that are neither stable nor uniform. Herein, we have developed a facile strategy that utilizes microwave radiation to anchor PB onto the surface of polyvinylpyrrolidone (PVP) functionalized graphene oxide (GO-PVP) through stable, uniform covalent bonds via the amide groups in PVP, in order to obtain an excellent composite material with Prussian blue and carbon materials for sodium-ion batteries. The as-prepared composite materials exhibit lower content of crystallization water and higher crystal integrity, delivering a high initial specific capacity of 165.2 mAh g−1 at 1 C rate and maintaining a capacity of 120.1 mAh g−1 after 500 cycles. This composite approach offers novel insights into the creation of uniform and stable PB/carbon materials as the cathode of sodium-ion batteries.

Spin Symmetry Breaking‐Induced Hubbard Gap Near‐Closure in N‐Coordinated MnO2 for Enhanced Aqueous Zinc‐Ion Battery Performance

AbstractTransition metal oxides (TMOs) are promising cathode materials for aqueous zinc ion batteries (ZIBs), however, their performance is hindered by a substantial Hubbard gap, which limits electron transfer and battery cyclability. Addressing this, we introduce a heteroatom coordination approach, using triethanolamine to induce axial N coordination on Mn centers in MnO2, yielding N‐coordinated MnO2 (TEAMO). This approach leverages the change of electronegativity disparity between Mn and ligands (O and N) to disrupt spin symmetry and augment spin polarization. This enhancement leads to the closure of the Hubbard gap, primarily driven by the intensified occupancy of the Mn eg orbitals. The resultant TEAMO exhibit a significant increase in storage capacity, reaching 351 mAh g−1 at 0.1 A g−1. Our findings suggest a viable strategy for optimizing the electronic structure of TMO cathodes, enhancing the potential of ZIBs in energy storage technology.

Functionalized porous conductive carbon layer improves the low-temperature performance of LiFePO4 cathode material for lithium-ion batteries

Lithium iron phosphate (LiFePO4) has been successfully utilized due to its stable structure, low cost, and higher safety. Nevertheless, the sluggish diffusion kinetics and low electrical conductivity have suppressed the rate capacity and long-term cyclability at lower temperature, causing significant capacity degradation problems. Herein, to address such issues, a well-designed 3D porous structure LFP@NS is synthesized via the sol-gel method combined with a high-temperature calcination route. Furthermore, the nitrogen and sulfur in thiourea can be induced to enter the carbon matrix, resulting in generating more defects and active sites. Simultaneously, N,S co-doped carbon matrix can form successive migration channels for lithium-ion, which can promote the diffusion kinetics and electrical conductivity. The as-prepared LFP@NS-2 sample provides 158.5 mAh g−1 discharge capacity in the room temperature (RT) and 101.3 mAh g−1 (in −20 °C) at 1C, and exhibits remarkable cyclic performance (122.3 mAh g−1 after 2000 circles at 10C in the RT). Furthermore, to investigate the practical application in low temperature, coupled with a graphite (Gr) anode, the LFP@NS-2||Gr full battery releases 100.1mAh g−1 at 1C in −20 °C. Therefore, this work has a far-reaching implication for designing the high-performance LIBs electrode materials for practical application at low temperature.