Capillary Electrophoresis Separation Research Articles

Achieving Stable Electrospray Ionization Mass Spectrometry Detection from Microfluidic Chips.

The past two decades have witnessed remarkable advances in the development of microfluidic devices as bioanalytical platforms for the analysis of biological molecules. The implementation of mass spectrometry (MS) detection systems on these devices has become inevitable, and various chip-MS ionization interfaces have been developed. As electrospray ionization (ESI) is particularly relevant for the analysis of large biological molecules such as proteins or peptides, efforts have focused on advancing interfaces that meet the demands of nano-separation techniques that are typically used prior to MS detection. Achieving stable ESI conditions that enable sensitive MS detection is, however, not trivial, especially when the spray is generated from a microfabricated platform. This chapter is aimed at providing a step-by-step protocol for producing stable and efficient electrospray sample ionization from microfluidic chips that are used for capillary electrophoresis (CE) separations.

Sample Injection Techniques.

Sample introduction is an important consideration in any microchip electrophoresis (ME) separation. The number of applications and level of complexity of ME devices continue to increase, but the introduction of sample into the separation channel has remained relatively constant. This work describes the most common electrophoretic methods of performing sample injection for ME applications using electroosmotic flow (EOF), providing both a transition from capillary electrophoresis (CE) separations and a straightforward entry point into ME.

Selective capillary electrophoresis separation of mono and divalent cations within a high-surface area-to-volume ratio multi-lumen capillary

In this study, the separation of inorganic mono and divalent cations using multi-lumen silica capillaries (MLCs) of 126 channels, each with either 4 or 8 μm inner diameter, was investigated using capillary electrophoresis and on-capillary capacitively coupled contactless conductivity detection (CE-C4D). MLCs provided sufficiently high surface area-to-volume ratios to generate significant wall ion-exchange interactions for the divalent cations, which significantly affected resultant selectivity, whereas monovalent cations were predominantly separated by simple electrophoresis. The resultant hybrid selectivity was seen for both 4 and 8 μm channel multi-lumen capillaries, without any preconditioning or capillary wall modification. Remarkably, the electrophoretic mobilities for the divalent cations Mg2+ and Ca2+ were reduced 7.5 times compared to those determined using a single channel open tubular capillary of 50 μm i.d., providing much improved selectivity. Apparent electrophoretic mobilities of divalent cations increased as the concentration of BGE increased, while those of monovalent cations decreased parallel to electroosmotic mobility. These results show the electrostatic interaction between the divalent cations and the silica wall. At least, this specific separation of mono- and divalent cations were clearly observed with a mixture standards solution of less than 200 μmol L−1. Using a MLC with 126 × 8 μm i.d. channels and 49.1 cm in length, together with a 20 mmol L−1 MES/His BGE, containing 2 mmol L−1 18-crown-6, monovalent cations (NH4+, K+ Na+ and Li+) and divalent cations (Ca2+ and Mg2+) could be completely separated within 4 min. For monovalent cations, on-capillary detection using C4D provided calibration curve (0–200 μmol L−1) correlation coefficients in the range R2 = 0.995–0.999, and limits of detection of 2.2–6.6 μmol L−1. Relative standard deviations for migration times were less than 0.6%, and recoveries ranged from the 93.8%–105.4%. The new method was applied to the separation and quantitative determination of monovalent and divalent cations in drinking waters and soil extracts.

Thread-based assay for quantitative small molecule analysis of mice tear fluid by capillary electrophoresis

Tear fluid plays blood-like roles in the cornea, and changes in its chemical composition may be reflective of ocular surface disease pathogenesis. Studies of mice tears are limited by the small volume available for collection and difficulty in obtaining representative samples. Here, we establish a non-invasive assay for small volume analysis of small molecules in mice tears that requires no pre-treatment of mice. To the best of our knowledge, this is the first small molecule analysis of mice tears. Nanoliters of mice tears (70 ± 25nL) was collected via a single insertion of phenol red thread in the corner of the eye without anesthesia to prevent any tear production alteration. The processing and elution of tear samples were optimized for minimal sample handling and dilution while maintaining high separation resolution. A capillary electrophoresis separation with light-emitting diode-induced fluorescence detection was developed for the analysis of primary amine-containing small molecules. The levels of arginine, alanine, aspartate, and glutamate after elution were in the micromolar range as seen in human tears. However, taurine and histamine levels were decreased and increased, respectively, compared to human tears, which may be indicative of restraint-induced emotional stress. No significant differences were seen for any of the small molecules between 20-week-old ND4 Swiss Webster females and 12-week-old CD-1 males (N = 3). The developed assay represents a means to assess the chemical composition of tear fluid in mouse models of human disease, which could significantly improve our understanding of ocular surface diseases. Graphical abstract ᅟ.

Speciation of organomercury compounds by capillary electrophoresis with pre-column derivatization and on-line stacking

Simultaneous separation and detection of three organomercury species, namely methylmercury (MeHg), ethylmercury (EtHg), and phenylmercury (PhHg), was performed by using capillary electrophoresis (CE) with UV detection. Pre-column derivatization with thiosalicylic acid and on-line salt-induced stacking significantly improved the detection performance. Buffer pH, ion strength, and additive were optimized for CE separation, concentration of NaCl in sample solution and injection time were optimized for on-line stacking. The limits of detection were 76.9, 83.0 and 76.4 μg/L for PhHg, EtHg and MeHg, respectively. The developed method was validated by certified reference material and liquid chromatography-atomic fluorescence spectroscopy, which suggests this method could be useful in the speciation of organomercury compounds in biological samples.

Investigation of dextrin-based synergistic system with chiral ionic liquids as additives for enantiomeric separation in capillary electrophoresis

In this paper, two spiral structure CILs, 1-butyl-3-methylimidazolium(T-4)-bis[(2S)-2-(hydroxy-κO)-3-methyl-butanoato-κO]borate(BMIm+BLHvB−) and 1-butyl-3-methylimidazolium (T-4)-bis[(αS)-α-(hydroxy-κO)-4-methyl-benzeneacetato-κO]borate (BMIm+BSMB-)were applied to evaluate their potential synergistic effect with dextrin for CE enantiomeric separation. The established dextrin-based synergistic system with CILs as additives showed good separation performance towards four tested drugs, including duloxetine, ketoconazole, sulconazole and citalopram. It was also observed that significantly improved separation and selectivity for tested analytes were achieved in CILs/dextrin synergistic system compared to single dextrin system. Primary parameters, such as the concentration of CIL, dextrin concentration, buffer pH and applied voltage, were systematically investigated to optimize the enantiomeric separation with BMIm+BLHvB−/dextrin as model system. Finally, the method of Statistical Product and Service Solutions (SPSS) was exploited to further elucidate the influence of experimental parameters on the synergistic effect.

Electropreconcentration, gate injection, and capillary electrophoresis separation on a microchip

The nanochannel-based electropreconcentration is not compatible with successive capillary zone electrophoresis (CZE). In this study, the incompatibility is theoretically discussed and experimentally proven, and then, the development of a monolithic glass microfluidic chip for performing integrated electropreconcentration and CZE separation is described. The sample is electropreconcentrated at the interface of a micro- and nanochannel where electric double layer overlap conditions exist. Because an ion-depletion region develops at the leading front of the preconcentrated plug, a field-enhanced sample stacking effect occurs which limits the separation efficiency unless compensated for. The ion-depletion region was confirmed by monitoring the solution conductivity at discrete points in the microchannel during the preconcentration step. The solution conductivity decreased >20-fold during the preconcentration step. To overcome the effects of this region, a cross-intersection was used to shunt the ion-depleted buffer away from the analysis channel while reintroducing the running buffer. When the preconcentrated sample plug arrives at the cross-intersection, it is gate injected into the analysis channel so that fresh running buffer surrounds the plug. Under these conditions, three-peptide mixture was preconcentrated ∼200-fold in 60 s and the preconcentrated plug was successfully resolved with better than 1% relative standard deviations in migration times.

Novel electrophoretic acetonitrile-based stacking for sensitive monitoring of the antiepileptic drug perampanel in human serum

Perampanel is a novel antiepileptic drug used in paediatric patients. Existing methods that determine serum perampanel are of limited practicability. We developed a novel capillary electrophoresis (CE) method using a new version of acetonitrile stacking for on-line sample pre-concentration, and fluorescence detection (FD). CE separations were performed in a fused-silica capillary where the electroosmotic flow was reduced by coating the inner surface using a INST coating solution. The optimised background electrolyte composition was 50 mM chloroacetic acid with addition of 0.5% m/v polyvinylalcohol (pH 2.15) and separation was driven by application of positive voltage + 30 kV. Serum samples (25 μL) treated by the addition of acetonitrile in a ratio of 1:3 v/v were each injected into the capillary at a large volume that corresponded to the length (129 mm) of the sample zone (hydrodynamic pressure impulse 6000 mbars). Acetonitrile stacking is based on the forcing the sample zone out of the capillary with simultaneous application of the separation voltage. Under such conditions, the enhancing factor achieves the value 57 for peak area compared to the small sample injection length (3.2 mm, hydrodynamic pressure impulse 150 mbar.s). A fluorescence detector with a broad excitation filter (240–400 nm) and an emission filter (495 nm) was used for visualisation of the native fluorescence of perampanel. The calibration dependence of the method was linear (in the range of 10–1000 ng mL−1), with adequate accuracy (99.8–103.3 %) and precision (13.1%). LOD and LOQ for perampanel were 2.9 ng mL-1 and 9.5 ng mL−1, respectively. Clinical applicability was validated using serum samples from patients treated with perampanel and the results corresponded with reference LC–MS/MS values. Our method offers a promising alternative for determining serum perampanel with several advantages. In particular, the low quantity of serum (25 μL) required means that testing can be performed on samples obtained for monitoring other antiepileptic medications, and thus reduces the test-burden on paediatric patients.

Ion-Exchange Chromatography Coupled With Dynamic Coating Capillary Electrophoresis for Simultaneous Determination of Tropomyosin and Arginine Kinase in Shellfish.

Tropomyosin (TM) and arginine kinase (AK) are known as two major allergens in seafood. For the first time, we demonstrate a newly developed ion-exchange chromatography coupled with dynamic coating capillary electrophoresis (IEC-DCCE) method to simultaneously analyze the TM and AK in shellfish. First, we have optimized the procedure of IEC for simple enrichment of TM and AK crude extract. By using 30 mM borate-borax at pH 9.0 with 0.3% (v/v) Tween-20 as a dynamic coating modifier for capillary electrophoresis (CE) separation, the migration time, separation efficiency and electrophoretic resolution greatly improved. The limits of detection (LOD) were 1.2 μg mL−1 for AK and 1.1 μg mL−1 for TM (S/N = 3), and the limits of quantification (LOQ) were 4.0 μg mL−1 for AK and 3.7 μg mL−1 for TM (S/N = 10). The recovery of AK ranged from 91.5 to 106.1%, while that of TM ranged from 94.0 to 109.5%. We also found that only when the concentrations of AK and TM were above LOD reported here, these proteins can stimulate human mast cell (LAD2) degranulation. Finally, the use of IEC-DCCE to analyze fresh shellfish samples highlights the applicability of this method for the simultaneous detection of these allergens in complex food systems.

Direct Hadamard Transform Capillary Zone Electrophoresis without Instrumental Modifications

We report the first successful implementation of a multiplexing method on a standard capillary electrophoresis system with UV detection that is independent of additional hardware. This was achieved using the Hadamard transform approach and employing vial exchange and voltage suspensions for translation of pseudorandom binary sequence elements into sample and background electrolyte injections of a capillary zone electrophoresis separation. Sequences exceeding peak capacity of the capillary were subdivided into shorter subsequences measured successively and realigned afterward based on EOF marker or analyte peaks. This way, we realized and deconvoluted modulation sequences as long as 8-bit (255 injections) for two systems containing either AMP or a mixture of the nucleotides (A,C,G,U)MP resulting in electropherograms of considerably improved signal-to-noise ratio. We achieved factors of intensity enhancement of around 6.9 and 5.2, respectively (theoretical maximum 8.0). This contribution, further, presents experimental and simulation studies on the effects on zones during injection and separation when experiencing voltage suspensions. Besides analysis of EOF behavior and influence of diffusion dispersion, we also provide data on the significance of specific electrophoretic errors such as peak position shift, inconsistent sample injection, and peak broadening on the quality of the inverse Hadamard transform. Moreover, the application of our approach to the practical analysis of a milk sample is described. The results demonstrate the applicability of multiplexing on unmodified standard CE instrumentation and establish a new suitable methodology to enhance the low sensitivity of on-column UV detection in capillary electrophoresis.

Using ZIF-8 as stationary phase for capillary electrophoresis separation of proteins

Recently, the separation of proteins has received much attention, although many techniques require expensive instrumentation and trained analysts. In this work, a low-cost, effective, and environmental friendship capillary electrophoresis (CE) for proteins separation was first time introduced. The ZIF-8 with outstanding properties of large surface area, and accessible tunnels and cages were coated the inner surface of silica capillary as a separation media by electrostatic interaction. The fast baseline separation of Lys, CC, BSA and RNase A can be obtained within 10 min using the ZIF-8 nanocrystals coated capillary column under the optimum separation conditions. Meanwhile, this system showed good reproducibility and stability. Using L-glutamic acid as the selector ligand, the D- and L-phenylalanine were successfully separated by the ZIF-8 nanocrystals coated capillary column. Furthermore, the method was also applied to separate egg white proteins, and three main proteins were separated in a single run.

Capillary electrophoresis, a method for the determination of nucleic acid ligands covalently attached to quantum dots representing a donor of Förster resonance energy transfer.

The synthesis and determination of the structure of a Förster resonance energy transfer probe intended for the detection of specific nucleic acid sequences are described here. The probe is based on the hybridization of oligonucleotide modified quantum dots with a fluorescently labeled nucleic acid sample resulting in changes of the fluorescence emission due to the energy transfer effect. The stoichiometry distribution of oligonucleotides conjugated to quantum dots was determined by capillary electrophoresis separation. The results indicate that one to four molecules of oligonucleotide are conjugated to the surface of a single nanoparticle. This conclusion is confirmed by the course of the dependence of Förster resonance energy transfer efficiency on the concentration of fluorescently labeled complementary single-stranded nucleic acid, showing saturation. While the energy transfer efficiency of the probe hybridized with complementary nucleic acid strands was 30%, negligible efficiency was observed with a noncomplementary strand.

Effective mobility as a robust criterion for compound annotation and identification in metabolomics: Toward a mobility-based library

Capillary electrophoresis (CE) presents many advantageous features as an analytical technique in metabolomics, such as very low consumption of a sample or the possibility to easily detect very polar and ionizable compounds. However, CE remains an approach only used by a few research groups due to a relatively lower sensitivity and, higher analysis time compared to liquid chromatography. To circumvent these drawbacks, herein we propose a generic CE–mass spectrometry (MS) approach using positive electrospray ionization mode and performing normal- and reverse-polarity CE separations to analyze anionic and acidic compounds. Preliminary experiments showed better sensitivity using the ESI positive mode compared to the ESI negative mode on a set of representative anionic compounds from different biochemical families. This approach was applied to the investigation of an available library of metabolites. More than 450 compounds out of the 596 in the library were detected, with the possibility to monitor negatively ionizable compounds through their ammonium adducts. Migration time of each data point was converted to an effective mobility (μeff) scale and used for peak alignment in data pre-processing; μeff features were used as a robust migration index for peak annotation and identification criterion. For the first time, a large database based on experimental μeff was built, allowing for the straightforward annotation of detected features in biological samples and demonstrating how CE-MS can complement other analytical techniques commonly used in metabolomics.

Characterization of oligo(acrylic acid)s and their block co-oligomers

Oligo(acrylic acid), oligoAA are important species currently used industrially in the stabilization of paints and also for the production of self-assembled polymer structures which have been shown to have useful applications in analytical separation methods and potentially in drug delivery systems. To properly tailor the synthesis of oligoAA, and its block co-oligomers synthesized by Reversible-Addition Fragmentation chain Transfer (RAFT) polymerization to applications, detailed knowledge about the chemical structure is needed. Commonly used techniques such as Size Exclusion Chromatography (SEC) and Electrospray Ionization-Mass Spectrometry (ESI-MS) suffer from poor resolution and non-quantitative distributions, respectively. In this work free solution Capillary Electrophoresis (CE) has been thoroughly investigated as an alternative, allowing for the separation of oligoAA by molar mass and the RAFT agent end group. The method was then extended to block co-oligomers of acrylic acid and styrene. Peak capacities up to 426 were observed for these 1D CE separations, 10 times greater than what has been achieved for Liquid Chromatography (LC) of oligostyrenes. To provide a comprehensive insight into the chemical structure of these materials 1H and 13C Nuclear Magnetic Resonance (NMR) spectroscopy was used to provide an accurate average chain length and reveal the presence of branching. The chain length at which branching is detected was investigated with the results showing a degree of branching of 1% of the monomer units in oligoAA with an average chain length of 9 monomer units, which was the shortest chain length at which branching could be detected. This branching is suspected to be a result of both intermolecular and intramolecular transfer reactions. The combination of free solution CE and NMR spectroscopy is shown to provide a near complete elucidation of the chemical structure of oligoAA including the average chain length and branching as well as the chain length and RAFT agent end group distribution. Furthermore, the purity in terms of the dead chains and unreacted RAFT agent was quantified. The use of free solution CE and 1H NMR spectroscopy demonstrated in this work can be routinely applied to oligoelectrolytes and their block co-oligomers to provide an accurate characterization which allows for better design of the materials produced from these oligomers.

Capillary Electrophoresis Sensitivity Enhancement Based on Adaptive Moving Average Method.

In the present work, we demonstrate a novel approach to improve the sensitivity of the "out of lab" portable capillary electrophoretic measurements. Nowadays, many signal enhancement methods are (i) underused (nonoptimal), (ii) overused (distorts the data), or (iii) inapplicable in field-portable instrumentation because of a lack of computational power. The described innovative migration velocity-adaptive moving average method uses an optimal averaging window size and can be easily implemented with a microcontroller. The contactless conductivity detection was used as a model for the development of a signal processing method and the demonstration of its impact on the sensitivity. The frequency characteristics of the recorded electropherograms and peaks were clarified. Higher electrophoretic mobility analytes exhibit higher-frequency peaks, whereas lower electrophoretic mobility analytes exhibit lower-frequency peaks. On the basis of the obtained data, a migration velocity-adaptive moving average algorithm was created, adapted, and programmed into capillary electrophoresis data-processing software. Employing the developed algorithm, each data point is processed depending on a certain migration time of the analyte. Because of the implemented migration velocity-adaptive moving average method, the signal-to-noise ratio improved up to 11 times for sampling frequency of 4.6 Hz and up to 22 times for sampling frequency of 25 Hz. This paper could potentially be used as a methodological guideline for the development of new smoothing algorithms that require adaptive conditions in capillary electrophoresis and other separation methods.

Separation of superparamagnetic magnetite nanoparticles by capillary zone electrophoresis using non-complexing and complexing electrolyte anions and tetramethylammonium as dispersing additive.

Separations of bare superparamagnetic magnetite nanoparticles (BSPMNPs, approx. 11 nm diameter) was performed using non-complexing (nitrate) and complexing (chloride, citrate and phosphate) electrolyte ions with additions of tetramethylammonium hydroxide (TMAOH), which is commonly applied to control the synthesis of stable iron oxides. The use of TMAOH as a background electrolyte (BGE) additive for capillary electrophoresis (CE) separations provided for the first time electropherograms of BSPMNPs exhibiting symmetrical and highly reproducible peaks, free of spurious spikes characteristic of nanoparticle clusters. Consequently, accurate determination of the electrophoretic effective mobility of BSPMNPs was possible, yielding a value of -3.345E-08 m2 V-1 s-1 (relative standard deviation (RSD) of 0.500%). The obtained mobilities of BSPMNPs in the presence of various electrolyte ions show that the degree of complexation with the surface of BSPMNPs follows the order chloride < citrate < phosphate, correlating with the stabilities of Fe(III) complexes with the respective anions. Finally, bare and carboxylated iron oxide nanoparticles were successfully separated in only 10 min using 10 mM Tris-nitrate containing 20mM of TMAOH as electrolyte. Our findings show that simple and rapid CE experiments are an excellent tool to characterise and monitor properties and interactions of iron oxide nanoparticles with other molecules for surface modification purposes.

Simultaneous detection of eight avian influenza A virus subtypes by multiplex reverse transcription-PCR using a GeXP analyser

Recent studies have demonstrated that at least eight subtypes of avian influenza virus (AIV) can infect humans, including H1, H2, H3, H5, H6, H7, H9 and H10. A GeXP analyser-based multiplex reverse transcription (RT)-PCR (GeXP-multiplex RT-PCR) assay was developed in our recent studies to simultaneously detect these eight AIV subtypes using the haemagglutinin (HA) gene. The assay consists of chimeric primer-based PCR amplification with fluorescent labelling and capillary electrophoresis separation. RNA was extracted from chick embryo allantoic fluid or liquid cultures of viral isolates. In addition, RNA synthesised via in vitro transcription was used to determine the specificity and sensitivity of the assay. After selecting the primer pairs, their concentrations and GeXP-multiplex RT-PCR conditions were optimised. The established GeXP-multiplex RT-PCR assay can detect as few as 100 copies of premixed RNA templates. In the present study, 120 clinical specimens collected from domestic poultry at live bird markets and from wild birds were used to evaluate the performance of the assay. The GeXP-multiplex RT-PCR assay specificity was the same as that of conventional RT-PCR. Thus, the GeXP-multiplex RT-PCR assay is a rapid and relatively high-throughput method for detecting and identifying eight AIV subtypes that may infect humans.

Characterization of Athabasca lean oil sands and mixed surficial materials: Comparison of capillary electrophoresis/low-resolution mass spectrometry and high-resolution mass spectrometry.

Oil sands mining in Alberta, Canada, requires removal and stockpiling of considerable volumes of near-surface overburden material. This overburden includes lean oil sands (LOS) which cannot be processed economically but contain sparingly soluble petroleum hydrocarbons and naphthenic acids, which can leach into environmental waters. In order to measure and track the leaching of dissolved constituents and distinguish industrially derived organics from naturally occurring organics in local waters, practical methods were developed for characterizing multiple sources of contaminated water leakage. Capillary electrophoresis/positive-ion electrospray ionization low-resolution time-of-flight mass spectrometry (CE/LRMS), high-resolution negative-ion electrospray ionization Orbitrap mass spectrometry (HRMS) and conventional gas chromatography/flame ionization detection (GC/FID) were used to characterize porewater samples collected from within Athabasca LOS and mixed surficial materials. GC/FID was used to measure total petroleum hydrocarbon and HRMS was used to measure total naphthenic acid fraction components (NAFCs). HRMS and CE/LRMS were used to characterize samples according to source. The amounts of total petroleum hydrocarbon in each sample as measured by GC/FID ranged from 0.1 to 15.1mg/L while the amounts of NAFCs as measured by HRMS ranged from 5.3 to 82.3mg/L. Factors analysis (FA) on HRMS data visually demonstrated clustering according to sample source and was correlated to molecular formula. LRMS coupled to capillary electrophoresis separation (CE/LRMS) provides important information on NAFC isomers by adding analyte migration time data to m/z and peak intensity. Differences in measured amounts of total petroleum hydrocarbons by GC/FID and NAFCs by HRMS indicate that the two methods provide complementary information about the nature of dissolved organic species in a soil or water leachate samples. NAFC molecule class Ox Sy is a possible tracer for LOS seepage. CE/LRMS provides complementary information and is a feasible and practical option for source evaluation of NAFCs in water.

Capillary electrophoresis for aluminum ion speciation: Optimized separation conditions for complex polycation mixtures

Aluminum chlorohydrates (ACH) are used in numerous applications and commercial products on a global scale including water treatment, catalysis or antiperspirants. They are complex mixtures of water soluble aluminum polycations of different degrees of polymerization, that are difficult to separate and quantify due to their susceptibility to depolymerize in solution when placed out of equilibrium, which is inherent to any separation process. We recently achieved the first capillary electrophoresis separation and characterization of ACH oligomers using 4-morpholineethanesulfonic acid (MES) as background electrolyte counter-ion. MES stabilizes the separated ACH oligomers during the electrophoretic process leading to highly repeatable and fast separations. In this work, the separation of ACH oligomers was further studied and perfected by varying the ionic strength, MES concentration and pH of the background electrolyte. Complex electrophoretic behavior is reported for the separation of Al13, Al30 and Na+ ions according to these experimental parameters. The transformation of the electropherograms in effective mobility scale and the use of the slope-plot approach are used to better understand the observed changes in selectivity/resolution. Optimal conditions (700 mM MES at 25 mM ionic strength containing 0.1 mM didodecyldimethylammonium bromide for dynamic capillary coating, pH 4.8) obtained for the separation of ACH oligomers are used for the baseline separation of samples difficult to analyze with other methods, including different molecular, aggregated and colloidal forms of aluminum from the Al13, Al30 and Na+ mixture, validating the rationale of the approach.

Plastid trnH-psbA intergenic spacer serves as a PCR-based marker to detect common grain adulterants of coffee (Coffea arabica L.)

The present work describes the utilization of interspecific length polymorphisms within the chloroplastic trnH-psbA intergenic spacer to standardize a DNA-based method that identifies adulteration in Arabica coffee (Coffea arabica L.). Adulteration of coffee with roasted cereal grains and soybean is a common fraudulent practice, yet, research to design sensitive DNA-based tests in order to establish traceability in coffee is extremely limited. In the present study, PCR-CE (PCR-capillary electrophoresis) analysis of the trnH-psbA intergenic spacer proved successful to discriminate Arabica coffee and its common adulterants, namely corn, soybean, rice, wheat and barley. When the barcode PCR-CE assay was tested on admixtures, adulteration as low as 1% was successfully detected simply through barcode amplification and capillary electrophoresis separation. Moreover, it is important to note that the proposed barcode assay not only detects adulteration but also reveals the identity of the adulterant species based on barcode amplification profiles obtained from reference sets of anticipated adulterants.