Brake Thermal Efficiency Research Articles

Experimental investigation on in-cylinder working process and thermal efficiency of ammonia/diesel low-carbon engine with pre-injection strategy

Ammonia, as a zero carbon and sustainable fuel, combined with traditional diesel fuel can provide a promising solution for reducing the engine environmental impact. However, ammonia/diesel dual-fuel (ADDF) engine has the significant drawback of low combustion efficiency and poor combustion stability at low loads, which seriously hinders its development. Therefore, this study explored the potential of pre-injection strategy in improving the performance of ADDF engine, comprehensively evaluating the effects of four pre-injection parameters (main injection timing (MIT), pre-injection timing (PIT), pre-injection quantity (PIQ), and diesel injection pressure (DIT)) on in-cylinder combustion process, incomplete combustion emissions, and energy efficiency. The results indicate that MIT has the most significant impact on combustion process. Advancing MIT can significantly increase in-cylinder combustion pressure and reduce CO, HC and unburned NH3 emissions. At MIT = -12 °CA ATDC, the highest brake thermal efficiency (BTE) of 32.3 % is obtained, while simultaneously generating high combustion noise. The advance of PIT has adverse effects on combustion stability. When PIT is advanced from −24 °CA ATDC to −36 °CA ATDC, COVIMEP increases from 2.61 % to 4.44 %, unburned NH3 emission increases by 23.5 %, and the BTE of ADDF engine decreases. Adjusting the PIQ and DIP can improve the reactivity distribution of fuel and reduce incomplete combustion emissions. However, the decrease in main injection quantity would increase the cycle fluctuation. At low loads, shortening the pre-main injection interval and increasing PIQ and DIP can enable the engine to achieve higher BTE while reducing pollutant emissions. This study elucidates in detail the influence of four pre-injection parameters on the operation characteristics of ADDF engine. It can offer insights and practical references for expanding the operating range of ammonia fuel engine.

Screening nano additives for favorable NOx/smoke emissions trade-off in a CRDI diesel engine fueled by industry leather waste fat biodiesel blend

The depletion of petroleum reserves and increasing environmental concerns prompted significant research into alternative fuels. This work, biodiesel, is extracted from the byproduct of industrial leather waste fat to generate beneficial energy.The main objective of this study is to enhance common rail direct injection (CRDI) diesel engine outcome characteristics by substituting industrial leather waste fat biodiesel (ILWFB) with the mixing of aluminium nitrate (Al (NO3)3) nanoparticles and graphene oxide nanoplates (GONPS) in the proportion of 50 ppm (parts per million) as catalysts to enhance ignition process. This research found that with the mixing of Al (NO3)3 nanoparticles and GONPS 50 ppm into the ILWFB blend, the in-cylinder pressure increased by 0.463% and 1.5%, and the heat release rate (HRR) improved by 4.19% and 12.04% than diesel and ILWFB blend at maximum load circumstances. Brake thermal efficiency (BTE) increased by 3.1% and 5.27%, and brake specific fuel consumption (BSFC) decreased by 3.57% and 7.14% in D50ILWFB50+Al (NO3)3 50 ppm blend and D50ILWFB50+GONPS 50 ppm blend related to diesel fuel. The carbon monoxide (CO), hydrocarbon (HC), and smoke emissions were reduced by 26.84%, 13.11%, and 5.75% in D50ILWFB50+Al (NO3)3 50 ppm blend and 38.94%, 21.31%, and 9.12% decreased in D50ILWFB50+GONPS 50 ppm blend than diesel fuel. Oxides of nitrogen (NOx) emissions marginally increased by 3.66%, 5.42%, and 8.94% in ILWFB blend, D50ILWFB50+Al (NO3)3, and D50ILWFB50+GONPSrelated to pure diesel at peak load conditions. This work concluded that the nano additives effectively enhanced BTE and decreased BSFC, CO, HC, and smoke emissions in diesel engine applications.

Water-in-Biodiesel Emulsion with Hydroxy (HHO) Gas Fuel Enrichment for Single-Cylinder Diesel Engine Application

The rising issue of the depletion of fossil fuels opened a new pathway to seek alternative fuels to fulfil World Sustainable Development Goals (SDG). The application of high-blending biodiesel is possible however, it causes the diesel engine to perform poorly due to high viscosity, high fuel consumption, and increased NOx emission. To comply with the strict regulation, the idea of combining alternative fuels of high blending biodiesel, water-in-biodiesel emulsion, and hydrogen is seen as possible to solve the issue of each alternative fuel. Therefore, this study focused on the effect of high blending of biodiesel, water-in-biodiesel emulsion with hydroxy (HHO) enrichment in single-cylinder diesel engines on engine performance and exhaust emission. The fuel tested for this study are B10, B50, and an emulsion of B50 with the addition of HHO known as B50H and tested on engine speeds of 2400rpm under various loading conditions of 1kW, 2kW, 3kW, and 4kW. The result showed the B50H showed improvement in Fuel Consumption (FC) by 4%, 5% for Brake Thermal Efficiency (BTE), and reduced Nitrogen oxide (NOx) by 23% compared to B10 fuel. Thus, the combination of high blending of biodiesel, water-in-biodiesel emulsion, and HHO gas successfully improved diesel engine performance and reduced harmful exhaust emissions to promote clean and renewable energy, without depending on current diesel fuel.

Design and performance analysis of hybrid electric class 8 heavy-duty regional-haul trucks with a micro-pilot natural gas engine in real-world highway driving conditions

Diesel-fueled heavy-duty (HD) trucks are a key component of global freight transport, but consume 25% of the transportation industry's energy and emitting substantial greenhouse gas (GHG) emissions. Utilizing low-carbon fuels like natural gas (NG), combined with hybridization, presents an excellent opportunity for reducing GHG emissions and fuel consumption. Micro-pilot dual fuel diesel/NG engines offer high engine brake thermal efficiency (BTE) with an efficient three-way catalyst (TWC) to limit pollutant emissions like CO2 without the need for costly exhaust aftertreatment systems. This engine is particularly well-suited for hybridization, as it features high-efficiency under stable, mid-, and high-load conditions, but with reduced performance at low loads. This paper validates two conventional baseline models (X15 Cummins diesel engine and micro-pilot NG engine) based on a tested class 8 regional-haul truck on highway. The study investigates the combined effect of low-carbon fuels and hybridization on improving the fuel economy and GHG emissions of class 8 regional-haul trucks. This involves designing pre-transmission parallel and plug-in hybrid configurations with downsized 6.7-liter micro-pilot NG engines. The cargo load and performance requirements are maintained equivalent to the conventional diesel baseline. Results show comparable fuel economy and engine BTE between conventional diesel baseline and NG models on highways with full cargo load. The parallel and series plug-in hybrid NG designs exhibit fuel economy improvements of 2.9% and 26%, respectively, compared to the micro-pilot NG over highway with full cargo load. In the same conditions, the CO2 emissions reductions for parallel and series plug-in hybrid NG designs are 15% and 51%, respectively, relative to the conventional diesel baseline. In addition, this article provides a detailed comparison and analysis of non-plug-in and plug-in hybrids based on component energy losses and internal combustion engine (ICE) operating points.

Performance enhancement of diesel engine using Karanja oil methyl ester as a fuel blend with diesel by variable injector nozzle hole

Diesel engines may run on biodiesel, a sustainable fuel that can be made from a variety of feedstocks using various alcohols and catalysts. The type of alcohol has a direct impact on the biodiesel’s fuel qualities. Variations in fuel qualities can lead to variations in diesel engine performance, combustion, and injection characteristics. Using blends of 10%, 20%, 30%, and 40% with Karanja oil and regular diesel fuel separately, experimental tests were conducted to assess the performance and emissions of a direct injection, water-cooled Kirloskar diesel engine at 1500 rpm with variable load. The 3-hole and 5-hole fuel injectors are the subjects of this investigation. Because Karanja methyl esters (KME) have a lower calorific value than diesel, their value increases with the proportion of KME in the mix. For a 20% blend, this means that brake-specific fuel consumption increases. As the amount of KME in the gasoline increases, the brake thermal efficiency falls. At a 20% mix, Brake thermal efficiency is almost identical to diesel fuel. For all blends, CO and HC emissions rise with load and fall with the fraction of KME in the mix. For every combination of KME, the density of smoke rises as the load increases. Smoke density falls as the fraction of mixes containing KME rises. It has been observed that when nozzle holes are increased from three to five, brake thermal efficiency rises with load. When comparing a 5-hole to a 3-hole with load, the Brake-specific fuel consumption (BSFC) will fall. Nozzles have an influence on emissions in that as nozzle holes grow, so do CO, HC, and smoke opacity. According to the findings, a 20% KME blend for a 5-hole fuel injector nozzle is a good substitute for diesel.

Investigations on the effects of injection parameters and EGR in a glow plug assisted methanol fueled Hot Surface Ignition (HSI) Engine

Methanol can be produced from renewable sources and is also clean burning. Hence it is an ideal alternative fuel for transportation applications. However, its low cetane number prevents its direct application in compression ignition (CI) engines. One of the promising but not widely explored methods is to use a hot surface for its ignition in CI engines at normal compression ratios. In this work a turbocharged automotive common rail diesel engine was modified to operate in the hot surface ignition (HSI) mode with methanol as the sole fuel with 3% by mass of lubricity and corrosion inhibiting additive. Initially, a single pulse injection (SPI) strategy was employed at different injection timings at a BMEP of 8 bar. Subsequently a double pulse injection (DPI) strategy was employed and the effects of gap between the injection pulses, injection timing and injection pulse width share among the two pulses were studied. The HSI mode of neat methanol performed with comparable brake thermal efficiency (BTE), reduced combustion rates and hence low NOx emission levels with respect to diesel operation when the DPI mode was employed with almost equal pulse width share. Engine performance was better at rail pressures of around 800 bar. Hot EGR of up to 8% was beneficial as it reduced the engine-out NOx without affecting the BTE. The engine was operated at different BMEPs in the range of 4–10 bar and compared with the baseline diesel operation. The BTE was similar to the baseline diesel engine at all loads. Engine-out NOx was lower than diesel operation by 23.6%–61.5% while near zero smoke levels and similar CO and THC emissions (after the DOC) were observed. Though slipped methanol and formaldehyde were the significant unregulated emissions, they were reduced to very low levels after the DOC.

Experimental Studies on the Jatropha-Biogas Dual Fuel Engine

In the current study, experiments were conducted on a compression ignition engine using neat vegetable oil (Jatropha oil) and biogas in the dual-fuel mode. A mono-cylinder, 4-stroke, direct injection, air-cooled diesel engine producing an output power of 4.4 kW at 1500 rpm was used to carry out the experiment. This engine was modified to operate in a dual fuel mode at 100% and 50% load conditions. From the result, the jatropha oil operation resulted in reduced thermal efficiency and increased smoke and hydrocarbon emissions. Brake thermal efficiency has been observed as 31% and 27% with neat-diesel fuel and jatropha oil respectively. While operating the engine in dual fuel mode, the thermal efficiency was observed to be inferior and increase in hydrocarbon emission, with a considerable reduction in smoke compared with single fuel operation. The key reason for lower thermal efficiency during dual fuel operation is mainly due to the presence of carbon dioxide in primary biogas fuel. Overall, it was concluded that adopting the dual fuel mode with vegetable oil as pilot fuel will result in reduced emissions and improvement in efficiency at medium and high outputs.

Performance and Emission Measurement of Spark Ignition Engines Operating with 100% Methanol Fuel

A small two-wheeler engine and a large, multi-cylinder bus engine are demonstrated for 100% methanol operation and, performance and emissions with methanol are compared to baseline. This kind of study on both small and large engines operating with 100% methanol is not reported in the literature as per the authors’ knowledge. A high flow injector is incorporated for the small engine for methanol. The fuel-air ratio is adjusted to operate the engine around a Lambda value of 1, and ignition timing is optimized to achieve maximum torque. Finer adjustments to Lambda are performed to maintain the nitrogen oxides emission less than that of the gasoline engine. The torque at wide-open throttle is higher than that of gasoline, around 5% higher brake thermal efficiency, and lower or similar regulated emissions are observed with methanol. For the large engine, a liquid nozzle and an electric fuel-pump are incorporated for methanol. Lambda is maintained around 1, and ignition timing is optimized for maximum brake torque while avoiding knocking. The rated torque and power are achieved with around 50% throttle opening, 3% higher brake-thermal efficiency, and lower nitrogen oxides are observed with methanol.

Optimizing soybean biofuel blends for sustainable urban medium-duty commercial vehicles in India: an AI-driven approach

This article presents the outcomes of a research study focused on optimizing the performance of soybean biofuel blends derived from soybean seeds specifically for urban medium-duty commercial vehicles. The study took into consideration elements such as production capacity, economics and assumed engine characteristics. For the purpose of predicting performance, combustion and emission characteristics, an artificial intelligence approach that has been trained using experimental data is used. At full load, the brake thermal efficiency (BTE) dropped as engine speed increased for biofuel and diesel fuel mixes, but brake-specific fuel consumption (BSFC) increased. The BSFC increased by 11.9% when diesel compared to using biofuel with diesel blends. The mixes cut both maximum cylinder pressure and NOx\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${{\ ext{NO}}}_{{\ ext{x}}}$$\\end{document} emissions. The biofuel-diesel fuel proved more successful, with maximum reduction of 9.8% and 22.2 at rpm, respectively. The biofuel and diesel blend significantly improved carbon dioxide (CO2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${{\ ext{CO}}}_{2}$$\\end{document}) and smoke emissions. The biofuel blends offer significant advantages by decreeing exhaust pollutants and enhancing engine performance.Graphical

Waste plastic oil as an alternative fuel: A review

Today, with the high population density of the world, the energy demand is increasing continuously. Global dependency on fossil fuels is very strong and there is a compelling need to reduce our energy consumption in order to offset greenhouse gas emissions. Due to regularly increasing prices of fossil fuels alternative fuels are needed to fulfill the requirements of developing countries like India. Plastics in today's world have become crucial. They are excessively used in industry, as well as in households and other fields due to their lightweight, durability, and design flexibility. Plastic demand is growing day by day, which now poses a huge environmental threat. The current study summarizes the use of WPO (waste plastic oil) in the diesel engine and also concludes the combustion, performance, and emission parameters. After an exhaustive literature search, some interesting results have been found. The study reveals that when using WPO as an alternative source in a diesel engine, the combustion, performance, and emissions are similar to those using conventional diesel fuel. An enhanced BTE (brake thermal efficiency) and reduced emissions of unburned hydrocarbons (UBHC) and carbon monoxide (CO) are reported.

Experimental investigations of CI engine performance using ternary blends of n-butanol/biodiesel/diesel and n-octanol/biodiesel/diesel

This study explored the ternary blends of biodiesel-diesel-n-butanol and biodiesel-diesel-n-octanol on common rail direct injec-tion (CRDI) diesel engines. The compositions of fuels, which varied from 0% to 100%, were altered by up to 5%. On the basis of their properties, these blends were chosen, with various concentrations of alcohol at 5% and 10%, 5% diesel, and the remainder being biodiesel. Two ternary fuel blends of waste cooking oil biodiesel (90–85%), diesel (5%), and butanol (5–10%), namely BD90D5B5 and BD85D5B10, and subsequently, another two ternary similar blends of waste cooking oil biodiesel (90–85%), diesel (5%), and octanol (5–10%), namely BD90D5O5 and BD85D5O10, were used to conduct the experiments. The experiments were done with varying injection pressure from 17° to 29° crank angle (CA) before top dead centre (bTDC). The optimum con-dition for the blends is achieved at 26°CA bTDC for 80% loading. So, the engine trials were conducted on 26°CA bTDC to attain the results. The BD90D5O10 blend achieved the lowest brake specific fuel consumption (BSFC) reading of 0.308 kg/kWh while operating at full load. The maximum brake thermal efficiency (BTE) was 31.46% for BD90D5B5. The maximum heat release rate (HRR) achieved with BD85D5O5 fuel blend was 58.54 J/°CA. The quantity of carbon monoxide that BD85D5B10 created was the lowest (25.86 g/kWh). BD85D5B10 had a minimal unburned hydrocarbon emission of 0.157 g/kWh while operating at full load. Oxides of nitrogen (NOx) were emitted in the maximum quantity by BD85D5O10, which was equal to 6.01 g/kWh. This study establishes the viability of blends of biodiesel and alcohol as an alternative for petro-diesel in the future to meet the growing global energy demand.

Experimental investigation of performance, emission, and combustion characteristics of a variable compression ratio engine using waste cooking vegetable oils blended with diesel

The availability of crude oil and petroleum products has become scarce and costly over the years leading to a stiff rise in engine fuel. Due to the depletion of conventional fuels; alternative fuels are gaining importance in recent times and Waste Cooking Vegetable Oils (WCVOs) are the viable option for the same. The present study highlights the performance, emission, and combustion characteristics of the Variable Compression Ratio (VCR) engine using three varieties of WCVOs (Ground Nut (GDN), Palm (PM), and Sunflower (SF)). Their inferior fuel features (density, viscosity, calorific value, etc.) are enhanced by blending 30 % of these oils with 70 % Diesel. The experiments are then conducted in the VCR engine using these blended oils under varying loading conditions (0–8 N) and at a constant speed of 1500 (RPM) with a compression ratio (18:1). It is seen that a single blend of Palm oil (PM) increases the engine Brake Thermal Efficiency (BTE) by 5 % in comparison to Diesel and other blended fuels (GDN, SF) owing to its lower calorific value and greater viscosity. The engine Brake Specific Fuel Consumption (BSFC) decreases with the increase in load and the lower loads reduce the BSFC for WCVOs by 9–15 % compared to Diesel. Engine emissions like Carbon Monoxide (CO), Nitrogen Oxide (NOx), and Hydrocarbons (HC) are also reduced significantly (by 12–15 %) using these blended oils compared to Diesel. The surge in both the Peak Cylinder Pressure (PCP) and Heat Release Rate (HRR) is also observed using these blended fuels, especially for Sunflower. Hence, these WCVOs are an appropriate option to advance the VCR engine performance and decrease its emissions.

Optimization and impact of modified operating parameters of a diesel engine emissions characteristic utilizing waste fat biodiesel/di-tert-butyl peroxide blend

This study comprehensively investigated the transesterification process of converting waste pork fat oil into biodiesel as a fuel for the common rail direct injection (CRDI) diesel engine. In addition, Di-tert-butyl peroxide (DTBP) is used as an ignition enhancer to minimize exhaust gas emissions. The test fuels are diesel and diesel-waste pork fat biodiesel (WPFB)-DTBP blend (B20DTBP10 by volume), were used to analyze the engine outcome parameters with modified engines operating conditions like various compression ratios (CRs 16, 17.5, and 19) and injection pressures (IPs 400, 500 and 600 bar) at maximum load. The experiment results revealed that higher CRs and IPs, the heat release rate (HRR) and cylinder pressure increased. The brake thermal efficiency (BTE) is enhanced by increasing CRs and IPs but lowered than neat diesel. Smoke opacity decreased while increasing CRs and IPs. At CR 19 and IP 600 bar, smoke opacity decreased by 18.29%, related to baseline diesel. Increasing CRs and IPs lowered HC and CO emissions, but increasing IPs increased both emissions. HC and CO emissions were lowered in CR 19 and IP 500 bar by 21.73% and 28.49% more than neat diesel. The lower CRs and IPs, the oxides of nitrogen (NOx) emissions decreased, but further increasing CRs and IPs, the NOx emissions increased. Compared to baseline diesel, NOx emissions decreased in CR 16 and IP 400 bar by 15.49%. It was discovered that with increasing CRs and IPs, the emissions decreased with a minor rise in NOx emissions. Furthermore, the experimental results matched the predictions of an artificial neural network (ANN) model. The research concluded that the blend B20DTBP10 with modified engine operating conditions CRs and IPs suits diesel engine operation.

Effect of multi ferrites nanoparticles added Terminalia bellirica biodiesel on diesel engine: Combustion, performance, and emission studies

The objective of current investigation is to assess the diesel engine performance, combustion, and emissions fuelled with bismuth ferrite codoped with zinc and manganese (BZnFMO) nanoparticles dispersed Terminalia bellirica biodiesel. BZnFMO nanoparticles were uniformly dispersed in B20 together with the surfactant and the dispersant at a concentration of 50 ppm and 75 ppm, respectively, and the stability of the nanoparticles in B20 was evaluated by UV photo spectroscopy. In addition, the experimental analysis of all nano-fuel samples was tested on diesel engines with different injection timing (i.e. 21°bTDC, 23°bTDC and 25°bTDC). The addition of nanoparticles in B20 led to an improvement in performance and combustion properties while simultaneously reducing emissions. The dispersion of BZnFMO nanoparticles in B20 led to a significant improvement in cylinder pressure (CP), cumulative heat release rate (CHRR), rate of pressure rise (RoPR) and brake thermal efficiency (BTE), while reducing brake specific fuel consumption (BSFC), carbon monoxide (CO), unburnt hydrocarbons (UHC), nitrogen oxides (NOx) and diesel engine smoke opacity. The increase in injection timing also led to an improvement in performance and combustion characteristics, as well as a reduction in emissions, with the exception of NOx. At 25°bTDC, a CP of 71.14 bar, a CHRR of 3.27 J/°CA and a RoPR of 5.3 bar/°CA were found, while BTE and BSFC were 35.03 % and 0.391 kg/kWh, respectively for B20 + 75 ppm BZnFMO + 75 ppm TWEEN 80. The values for CO, UHC, NOx, smoke opacity and nitrogen oxides were 0.01 %, 22 ppm, 826 ppm and 35.85 % respectively.

Performance and emission characteristics of biogas fuelled dual fuel engine with waste plastic oil as secondary fuel

This study investigates the performance, emission and combustion characteristics of a stationary engine under diverse operating conditions. The research focuses on the impact of waste plastic oil (WPO) blends with and without biogas addition. WPO added in diesel at various proportions such as 20%, 35% and 50% by volume. Biogas is inducted through inlet manifold. Biogas flow rate was varied. This study introduces a pioneering approach by investigating the superior performance of WPO blends coupled with the unique exploration of biogas addition, revealing intricate relationships between fuel blends and combustion characteristics for enhanced stationary engine efficiency and reduced emissions. Notably, WPO with 80% diesel (WPO20) demonstrates superior Brake Thermal Efficiency (BTE), showcasing a significant increase compared to WPO35 and WPO50 across varying load conditions. The addition of biogas to WPO20 results in a measurable reduction in BTE due to incomplete combustion, insufficient excess air, and increased emissions. Hydrocarbon (HC) emissions increase with load for WPO blends, with WPO20 exhibiting the lowest HC emissions. Carbon monoxide (CO) emissions are influenced by WPO concentration, with WPO20–B12 and WPO20–B16 dual fuel mode showing varying trends. Nitrogen oxides (NOx) emissions decrease with the addition of biogas, indicating a 10% reduction for WPO20–B16 compared to WPO20–B12. Smoke emissions increase with higher WPO concentrations but decrease with the introduction of biogas, exhibiting a 20% reduction in smoke for WPO20–B16 compared to WPO20–B12.

Emission and performance investigation of mango seed oil biodiesel supplied with n-pentanol and n-hexanol additives and optimization of fuel blends using modified deep neural network

Abstract In this study, the emission and performance characteristics of single-cylinder diesel engines were tested using various biodiesel blends prepared by mixing diesel with mango seed oil biodiesel (MSOB). Furthermore, the effect of n-amyl and n-hexanol alcohol additions on the performance and emission results of manufactured biodiesel blends is investigated and compared with diesel fuel. On the other hand, a hybrid deep neural network (DNN) based on the manta ray foraging optimization (MRFO) method is developed to forecast ideal biodiesel blends in order to reduce emissions from diesel engines while improving performance. The optimal brake thermal efficiency (BTE) and brake specific fuel consumption (BSFC) for this study were 32.3916 % for 75 % diesel + 20 % MSOB + 5 % n-hexanol fuel and 0.0453 kg/kWh for 75 % diesel + 20 % MSOB + 5 % n-amyl fuel, respectively. The optimal emissions from the test engine were 0.1034 % CO from 60 % diesel + 20 % MSOB + 20 % n-hexanol and 28.886 ppm HC from 75 % diesel + 20 % MSOB + 5 % n-hexanol fuel. The optimal smoke and NO x levels are achieved with a blend of 60 % diesel, 20 % MSOB, 5 % n-amyl, and 5 % n-hexane. Moreover, the developed DNN-MRFO achieved 0.9979, 0.9992 and 0.9975 overall regression coefficients during training, validation and testing. The root mean square error (RMSE) of DNN-MRFO also ranges from 0.019 to 0.032.

Combined influence of thermal barrier coating and nanoparticle on performance and emissions of DI diesel engine fueled with neat palm oil biodiesel: An experimental, statistical and energy and exergy analysis

In the present work, neat palm biodiesel (BD 100) was utilized in the compression ignition (CI) engine under the influence of thermal barrier coating and cerium oxide (CeO2) nanoparticles.The optimal factor conditions were determined through statistical analysis using the Response Surface Methodology (RSM), with appropriate input parameters provided. The results show that using a thermal barrier coated (TBC) engine with a 200 micron (0.2 mm) thickness of cylinder liner and 45 ppm cerium oxide nanoparticles combined with 100% palm biodiesel significantly improves performance and reduces emissions.The energy and exergy methodology tool was then used to analyze the various fuel conditions in order to examine the variations in energy flow.The assessment criteria that were experimentally confirmed were an average reduction in specific fuel consumption (SFC) of 0.065 kg/kWh and an increase in brake thermal efficiency (BTE) of 4.07%. The reduction of exhaust gases was seen to be significant when compared to those obtained from an uncoated engine running on diesel fuel, as indicated by the carbon monoxide (CO) level of 0.0916% by volume, the unburned hydrocarbon (UBHC) level of 38.2 parts per million (ppm), NOx of 132 ppm and the smoke opacity level of 10.52%.

Determination of Optimum Operating Parameters in a Non-Road Diesel Engine Fueled with 1-Heptanol/Biodiesel at Different Injection Pressures and Advances

It is important to reduce the negative environmental effects of non-road diesel engines, which are increasingly used in many facilities and machines, without loss of performance. Biodiesel is used as an alternative to fossil-based diesel fuels to eliminate these effects and ensure sustainability in energy. This study focused on the optimization of the operating parameters of a non-road diesel engine operating with a waste frying oil biodiesel mixture at 50% load. Pure biodiesel, 1-heptanol, different injection advances and pressures were determined as input parameters for optimization. The tests were designed according to Taguchi’s L16 orthogonal array. ANOVA analysis was performed to determine the importance of input parameters on engine performance and exhaust emissions. Optimization was made based on the highest brake thermal efficiency (BTE) in addition to the lowest values of brake-specific fuel consumption (BSFC), brake-specific hydrocarbon (BSHC), brake-specific nitrogen oxide (BSNOx) and smoke emissions. In the optimization carried out according to the response surface methodology (RSM), the optimum combinations to obtain the best engine characteristics were determined as 17.27% 1-heptanol, a 226-bar injection pressure, 27 CAD injection advance and B75. These optimization results were verified by engine experiments within the recommended error range.

Performance and CO2 emission of a single cylinder compression ignition engine powered by Khaya senegalensis non-edible seeds fuel blends

This work aimed at investigating blends of Khaya senegalensis biodiesel in a compression ignition engine, attempting to improve engine performance and reduce CO2 emission compared with conventional diesel. Analysis of System (ANSYS) was used to predict in-cylinder behavior of the fuel. ANSYS SpaceClaim generated the geometric model on which 5° sector and mesh refinement was on ANSYS Internal Combustion Engine Modeler (ICEM). Computational domain of interest lies within the compression and expansion strokes. Experimental validation followed: 5% biodiesel, 95% diesel (B5); 15% biodiesel, 85% diesel (B15); 25% biodiesel, 75% diesel (B25); pure diesel (D100); pure biodiesel (B100) in volume proportions. B15 has the highest brake mean effective pressure (BMEP) of 4 bar as load increases. An experimental and numerical comparison reveals pressure declination against speed increment. Ignition temperature fluctuated between 799.76 and 806.256 K for D100 and 760.73–790.62 K for B100 within 1800–2800 rpm speed limit prediction. Power and brake thermal efficiency (BTE) had parallel load increment with all blends. CO2 emission on increasing load conditions were 47.01%, 8.07%, 21.72% and 6.06% for B5, B15, B25, and B100 respectively lower than D100. Pressure and temperature contours gave proper combustion predicted behaviors. All blends possess replaceable performance potential for D100 however, B5 offers better reliable potentials.

Integrated optimization of common rail direct injection diesel engine input parameters with linseed biodiesel: A hybrid approach using grey relational analysis and genetic algorithm techniques

In the pursuit of improved productivity and efficiency, the search for alternative fuels that reduce dependence on fossil fuels is of utmost importance. This research study aims to investigate the influence of process parameters, namely blend percentage, fuel injection pressure, exhaust gas recirculation (EGR) rate, and engine load, on various engine performance parameters such as torque, brake thermal efficiency (BTE), brake mean effective pressure (BMEP), hydrocarbon emissions (HC), and mechanical efficiency. The experiments are conducted following the Taguchi orthogonal array (L25) design of experiments. Additionally, grey relational analysis, a multi-objective optimization technique, is applied to identify the optimal levels of the process variables that optimize all the response parameters. The optimal values obtained through grey relational analysis are determined as 0% blend, 600 bar fuel injection pressure, 12% EGR rate, and 12 kg engine load. Moreover, the Genetic Algorithm-based Multi-Objective Genetic Algorithm (MOGA) is employed for multi-objective optimization of the engine input variables, yielding optimal levels of 19.45% blend, 594.35 bar fuel injection pressure, 14.12% EGR rate, and 12 kg engine load. Furthermore, multivariable regression models are developed to predict the response variables within the experimental domain. These models are validated through a confirmation test. The findings of this study provide insights into the optimization of process variables for enhanced engine performance, with the developed models serving as valuable tools for future predictions and optimization.