Blue Dye Research Articles

Exploring the potential of olive pomace derived activated charcoal as an efficient adsorbent for methylene blue dye: a comprehensive investigation of isotherms, kinetics, and thermodynamics

Methylene blue (MB) is a heterocyclic aromatic chemical compound used as a dye in various dyeing processes. The accumulation of such an organic compound poses a significant threat to both the environment and human health. Therefore, numerous biological, physical, and chemical processes have been established to remove MB dye, with adsorption being the most predominant dye-based treatment technology. In this context, the aim of this work was to evaluate the adsorption properties of activated carbon derived from olive pomace against methylene blue. To this end, scanning electron microscopy (SEM), energy dispersive x-ray spectroscopy (EDS), and Fourier transform infrared spectroscopy (FT-IR) analyses were carried out to confirm the adsorption of MB on carbon structures. In addition, the effect of contact time, pH, initial dye concentration, adsorbent dose, and temperature on the adsorption efficiency of MB was investigated. On the other hand, kinetic and isothermal models were used to further understand the adsorption mechanism, which showed a good correlation with the pseudo-second-order kinetic model and the Langmuir isotherm. Finally, thermodynamic analysis showed favorable conditions for physisorption, with the process being both endothermic and spontaneous.

The effect of Ce doping on the structural, optical, and photocatalytic degradation of Mn–Co nanoferrites

This work demonstrates the preparation of Ni0.5Mn0.25Co0.25CexFe2-xO4 spinel nanoferrites (NMCCF nanoferrites) using the citrate combustion method. This study also investigated the characteristics of their structure, optics, and ability to degrade under light. The lattice strain and crystallite size of each NMCCF nanoferrite were measured by evaluating the XRD results using Williamson-Hall plots. The crystallite size was between 40 and 78 nm. The hopping lengths, bond lengths, surface areas, and densities of all NMCCF nanocrystals were measured and calculated. FTIR analysis showed two strong frequency bands at 571 and 390 cm−1, which are characteristic of spinel ferrites. SEM was used to investigate the particle size, composition, and distribution of the nanoferrites in the NMCCF sample. Scanning electron microscopy (SEM) analysis revealed the presence of spherical NMCCF nanoparticles and their tendency to aggregate. The Kubelka-Munk function and Tauc plots were used to predict the direct allowed Eg value of the NMCCF samples. NMCCF0, NMCCF1, NMCCF2, NMCCF3, NMCCF4, and NMCCF5 exhibited bandgap values of 1.515, 1.545, 1.506, 1.507, 1.499, and 1.473 eV, respectively. The behavior of Eg can be explained based on two criteria: doping impact and particle size. A comparative analysis of the photocatalytic degradation of the ideal sample (Ni0.5Mn0.25Co0.25Ce0.1Fe1.9O4) and other published photocatalytic materials demonstrated that the NMCCF5 nanoferrite exhibited a greater ability to remove methylene blue dye (97.38 %, within 60 min) compared to those materials. In addition, this comparative investigation demonstrated the enhanced stability of photocatalytic degradation capability exhibited by the current nanoferrites (with just a 1.55 % loss in efficiency after five cycles). This paper introduces an innovative method for producing spinel nanoferrites, with a specific focus on their structural, optical, and photocatalytic properties, which can be useful in the field of water treatment.

WITHDRAWN: Recombinant osteopontin stabilizes the blood brain barrier following subarachnoid hemorrhage in rats

Background and PurposeRecombinant osteopontin (rOPN) decreases neuronal cell death and brain edema and improves the neurological scores following subarachnoid hemorrhage (SAH) in rats. The molecular mechanisms of the preservation of blood-brain barrier of rOPN following SAH in rats were examined in this study. MethodsAdult rats were divided into 3 groups: sham, vehicle, and treatment groups. Each animal in the SAH group underwent a surgical procedure to induce SAH, and the brains was harvested at 24 hours for analysis. For the mechanism part of the study two additional groups were operated and treated with Fib-14 and Wortmannin additional to rOPN. rOPN was administered via the nasal route and neurological scores as well as brain water content were evaluated at 24 hours after SAH induction. The blood brain barrier (BBB) permeability was evaluated using Evans Blue dye extravasation. The expressions of tight junction proteins claudin-3, claudin-5, occludin and the phosphorylation of β-catenin were examined using Western blot analysis. ResultsrOPN improved neurological scores and reduced brain edema at 24 hours after SAH. The BBB preservation action of rOPN is mediated in part through stabilizing β-catenin and increasing expression of tight junction proteins, claudin-3, claudin-5, and occludin. rOPN is thought to exert its effects through FAK activated PI3K-Akt pathway. ConclusionSince BBB disruption is one of the major pathophysiology of EBI after SAH, rOPN may be a promising drug to maintain BBB integrity and functions in SAH treatment.

Temporal evolution of optical and photocatalytic properties of hydrothermally synthesized EDTA-encapsulated CdS spherical nanostructures

EDTA encapsulated CdS spherical nanocrystals have been prepared via hydrothermal approach at three different reaction times 16 h, 20 h, and 24 h. The XRD investigation confirms the formation of cubic and hexagonal mixed phase of CdS while HRSEM image validates the synthesis of spherical nanocrystals. The EDX spectra confirm the purity of the samples. The optical properties have been studied using UV–Vis and photoluminescence spectroscopic techniques. The PL spectrum at 20 h reaction time shows utmost intensity. The vibrational properties of the synthesized CdS samples have been investigated using FTIR technique in the range of 500 – 4000 cm−1. The photocatalytic properties of EDTA@CdS spherical nanocrystals to degrade methyl blue dye have been studied under sunlight.

Unveiling the synthesis, characteristics, electrical conductivity, photocatalytic activity, and electrochemical activity of eco-friendly zinc oxide nanoparticles

The Nigella Sativa seeds were utilized for the environment-friendly zinc oxide nanoparticles (ZnO NPs), as evident by the observation of a white precipitate. Numerous analytical techniques, such as XRD, FTIR, UV–vis, SEM, and EDX, were utilized to describe the specimen's structural, optical, and electrical properties. XRD analysis was used to confirm that the ZnO NPs were crystalline. An absorbance peak at 401 nm was observed in the UV–vis, indicating that the ZnO NPs have a 2.91 eV bandgap. Functional groups are present in ZnO NPs, as seen by the FTIR graph. The nanoparticles' spherical form and average size of 37.9 nm were confirmed by the SEM image. EDX analysis confirmed the composition of the nanoparticles, with zinc accounting for 73.17% and oxygen for 26.83%. ZnO NPs demonstrated excellent electrical conductivity because of their higher surface-to-volume ratio. Additionally, the synthesis of ZnO NPs exhibited effective degradation of methylene blue dye. These results point to potential applications in several domains, including electronics, biomedical devices, industry, and agriculture, and they call for immediate follow-up research.

Liposomal Nanocarriers of Preassembled Glycocalyx Restore Venular Permeability in Sepsis: Assessed Quantitatively with a Novel Microchamber System

Background: The endothelial glycocalyx (EG), covering the luminal side of endothelial cells, regulates vascular permeability and senses wall shear stress. In sepsis, EG undergoes degradation leading to increased permeability and edema formation. We hypothesized that restoring EG integrity using liposomal nanocarriers of preassembled glycocalyx (LNPG) will restore normal venular permeability in a lipopolysaccharide (LPS)-induced sepsis model of mice. Methods: To test this hypothesis, we designed a unique perfusion microchamber in which the vascular permeability of isolated and cannulated mice mesenteric venules could be assessed by measuring the concentration of Evans blue dye (EBD) by fluorescent spectroscopy in microliter-samples of extravascular solution (ES). Results: Histamine-induced time- and dose-dependent increases in EBD in the ES could be measured, confirming the sensitivity of the microchamber system. Notably, the histamine-induced increase in permeability was significantly attenuated by histamine receptor (H1) antagonist, triprolidine hydrochloride. Subsequently, mice were treated with LPS, or LPS + LNPG. Compared to control mice, venules from LPS-treated mice showed a significant increased permeability, which was significantly reduced by LNPG administration. Moreover, in the presence of wall shear stress, intraluminal administration of LNPG significantly reduced the permeability in isolated venules from LPS-treated mice. Conclusion: Our newly developed microchamber system can quantitatively measure the permeability of isolated venules. LPS-induced sepsis increases permeability of venules that is attenuated by in vivo LNPG administration, which is also reestablished endothelial vasomotor responses to shear stress. Thus, LNPG presents a promising therapeutic potential for restoring EG function and thereby mitigating the increased permeability in sepsis. Support: National Institute of Health [grant number: HL144528, Dong Sun] and the Uehara Memorial Foundation [grant number: 202241049, Shinya Ishiko) and Hungarian Academy of Sciences Post-Covid 2021-34 (AK) and MIT of Hungary, National Research, Development, and Innovation Fund, OTKA K 132596 (AK). This is the full abstract presented at the American Physiology Summit 2024 meeting and is only available in HTML format. There are no additional versions or additional content available for this abstract. Physiology was not involved in the peer review process.

Highly effective ultrafiltration membranes based on plastic waste for dye removal from water.

Applicable and low-cost ultrafiltration membranes based on waste polystyrene (WPS) blend and poly vinylidene fluoride (PVDF) were effectively cast on nonwoven support using phase inversion method. Analysis was done into how the WPS ratio affected the morphology and antifouling performance of the fabricated membranes. Cross flow filtration of pure water and various types of polluted aqueous solutions as the feed was used to assess the performance of the membranes. The morphology analysis shows that the WPS/PVDF membrane layer has completely changed from a spongy structure to a finger-like structure. In addition, the modified membrane with 50% WPS demonstrated that the trade-off between selectivity and permeability is met by a significant improvement in the rejection of the membrane with a reduction in permeate flux due to the addition of PVDF. With a water permeability of 50 LMH and 44 LMH, respectively, the optimized WPS-PVDF membrane with 50% WPS could reject 81% and 74% of Congo red dye (CR) and methylene blue dye (MB), respectively. The flux recovery ratio (FRR) reached to 88.2% by increasing PVDF concentration with 50% wt. Also, this membrane has the lowest irreversible fouling (Rir) value of 11.7% and lowest reversible fouling (Rr) value of 27.9%. The percent of cleaning efficiency reach to 71%, 90%, and 85% after eight cycles of humic acid (HA), CR, and MB filtration, respectively, for the modified PS-PVDF (50%-50%). However, higher PVDF values cause the membrane's pores to become clogged, increase the irreversible fouling, and decrease the cleaning efficiency. In addition to providing promising filtration results, the modified membrane is inexpensive because it was made from waste polystyrene, and as a result, it could be scaled up to treat colored wastewater produced by textile industries. PRACTITIONER POINTS: Recycling of plastic waste as an UF membrane for water/wastewater treatment was successfully prepared and investigated. Mechanical properties showed reasonable response with adding PVDF. The modified membrane with 50% PS demonstrated that the trade-off between selectivity and permeability is met by a significant improvement in the rejection.

Effect of the Photoreduction Process on the Self-Cleaning and Antibacterial Activity of Au-Doped TiO2 Colloids on Cotton Fabric.

This study aims at understanding the effect of the photoreduction process during the synthesis of gold (Au)-doped TiO2 colloids on the conferred functionalities on cotton fabrics. TiO2/Au and TiO2/Au/SiO2 colloids were synthesized through the sol-gel method with and without undergoing the photoreduction step based on different molar ratios of Au:Ti (0.001 and 0.01) and TiO2/SiO2 (1:1 and 1:2.3). The colloids were applied to cotton fabrics, and the obtained photocatalytic self-cleaning, wet photocatalytic activity, UV protection, and antibacterial activity against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) bacteria were investigated. The obtained results demonstrated that the photoreduction of Au weakened the self-cleaning effect and reduced the photocatalytic activity of coated fabrics. Also, an excess amount of Au deteriorated the photocatalytic activity under both UV and visible light. The most efficient self-cleaning effect was obtained on fabrics coated with a ternary TiO2/Au/SiO2 colloid containing ionic Au, where it decomposed coffee and red-wine stains after 3 h of illumination. Adding silica (SiO2) made the fabrics superhydrophilic and led to greater methylene blue (MB) dye adsorption, a faster dye degradation pace, and more efficient stain removal. Moreover, the photoreduction process affected the size of Au nanoparticles (NPs), weakened the antibacterial activity of fabrics against both types of tested bacteria, and modestly increased the UV protection. In general, the photoactivity of Au-doped colloids was influenced by the synthesis method, the ionic and metallic states of the Au dopant, the concentration of the Au dopant, and the presence and concentration of silica.

Effect of surfactants (cetyl trimethyl ammonium-bromide, ethyl di-tetra amine and polyacrylamide) on the synthesis of zinc oxide for photocatalytic application

In this work, we report the effect of cetyl trimethyl ammonium bromide (CTAB), ethyl di-tetra amine (EDTA) and polyacrylamide as surfactants on synthesis of zinc oxide for photocatalytic application. The ZnO nanoparticles were synthesized with and without the surfactants and characterized using powder X-ray diffraction (PXRD), and Fourier transform infrared spectroscopy (FTIR). In addition to this, the morphology of zinc oxide prepared in the absence and presence of these surfactants investigated through scanning electron microscopy (SEM). As confirmed from XRD and FTIR characterization results, the use of different surfactants did not affect the composition of ZnO nanomaterials. The photocatalytic activities were investigated by the degradation of methylene blue (MB) dye under sunlight irradiation. To optimize the effects of operational parameters, the study was carried out as a function of dye concentration, catalyst dose, and pH on the degradation efficiency of the photocatalysts. The optimum values of catalyst dose, dye concentration and pH of solution were found to be 0.09 g, 5 mg/L and 10, respectively. The ZnO nanomaterials prepared with CTAB surfactant showed highest degradation efficiency of 98% indicating potential application for practical decontamination of wastewater from toxic organic pollutants. KEY WORDS: Surfactants, Zinc oxide nanoparticles, Photocatalysis, Methylene blue Bull. Chem. Soc. Ethiop. 2024, 38(4), 923-935. DOI: https://dx.doi.org/10.4314/bcse.v38i4.9

Adsorption and bacterial performance of Nd2O3 modified Ag nanoparticles with enhanced degradation of methylene blue

Our study focused on the optical behavior, methylene blue (MB) dye degradation potential, antibacterial performance, and silver and trioxide mineral interaction with different bacterial species. We found that the addition of silver nanoparticles (Ag NPs) to neodymium oxide (Nd2O3) resulted in a significant response, with an enlargement of the inhibition zone for bacterial species such as Staphylococcus aureus and Escherichia coli. Specifically, the inhibition zone for S. aureus increased from 9.3 ± 0.5 mm for pure Nd2O3 to 16.7 ± 0.4 mm for the Ag/Nd2O3 nano-composite, while for E. coli, it increased from 8.8 ± 0.4 mm for Nd2O3 to 15.9 ± 0.3 mm for Ag/Nd2O3. Furthermore, the optical behavior of the composites showed a clear band-gap narrowing with the addition of Ag NPs, resulting in enhanced electronic localization. The direct and indirect transitions reduced from 6.7 to 6.1 eV and from 5.2 to 2.9 eV, respectively. Overall, these results suggest that the Ag/Nd2O3 nano-composite has potential applications in sensor industries and water treatment, thanks to its enhanced optical behavior, antibacterial performance, and efficient MB degradation capabilities. In terms of MB degradation, the Ag/Nd2O3 mixed system exhibited more efficient degradation compared to pure Nd2O3. After 150 min, the MB concentration in the mixed system decreased to almost half of its starting point, while pure Nd2O3 only reached 33%.

Decolourization of Methylene Blue by using Eucalyptus Globulus Leaf Powder as a Adsorbent

In the present study, the feasibility of using low-cost adsorbent Eucalyptus Globulus leaf powder for the cationic dyes adsorption from aqueous solutions have been investigated. Batch adsorption studies are conducted to study conducted to the different parameters are adsorbent dosage of 2-20 g/L, initial dye concentration of 50-250 mg /L, Temperature of 293oK, 303 oK and 313 oK on adsorption of methylene blue dye at equilibrium time of 80 minutes respectively and optimal pH of 5.0. The equilibrium data is analysed with isotherm models are Langmuir and Freundlich and kinetic models are Pseudo-first order, Pseudo-second order model. The adsorption equilibrium and kinetic data fitted well to Freundlich isotherm model for methylene blue dye and Pseudo-second order model for methylene blue dyes. The adsorption is an Endothermic and it is energetically favourable adsorption. The result demonstrates that Eucalyptus Globulus leaf powder could be employed as effective and low-cost adsorbent for the removal of methylene blue and from aqueous solutions.

BREWERY WASTE FOR INDIGO BLUE ADSORPTION

Brewery waste (BW) is among the natural adsorbents that have been evaluated for different chemical pollutants removal present in the aqueous medium. In this work, we investigated the BW capacity to remove the commercial indigo blue dye (IB) from laboratory aqueous solutions and river water samples. Results utilizing laboratory distilled water showed a satisfactory maximum capacity (166.94 mg/g) of BW for IB. The ∆G value (-16.53 Kj/mol) and other parameters reveal a favorable adsorptive process. Furthermore, tests in glass columns using river water samples enriched with IB (1,000 mg/L) revealed high BW efficiency for IB removal (96.0 %). These results are important to demonstrate that BW can be more a new alternative for IB removal from water. In addition, this study provides an alternative for the reuse of BW.

In vitro analysis of material micro-leakage in pit and fissure sealants

A preferable choice of material offers superior resistance against micro-leakage for clinical applications in preventing dental caries in pits and fissures is of interest. A total of 45 extracted human premolars were cleaned, stored in a saline solution, and randomly divided into three groups, each intended for treatment with one of the sealants: Fuzi VII, ClinPro, and Embrace Wetbond. The application of the sealants followed the manufacturers' instructions strictly. The teeth were subjected to thermal cycling to simulate oral conditions. Marginal micro-leakage was then assessed by dye penetration method using a 0.5% methylene blue dye. Teeth were sectioned, and dye penetration was measured under a stereomicroscope. The results showed that all the tested materials exhibited some degree of micro-leakage. Within the limitations of this in vitro study, it was concluded that Embrace Wetbond exhibited superior performance in terms of minimizing marginal micro-leakage among the tested pit and fissure sealants.

Environmentally friendly silver nanoparticles synthesized from Verbascum nudatum var. extract and evaluation of its versatile biological properties and dye degradation activity.

In the present study, green synthesis of silver nanoparticles (VNE-AgNPs) via Verbascum nudatum extract was carried out for the first time. The synthesized AgNPs were characterized by different spectral methods such as UV-vis, FTIR, XRD, TEM, and EDAX. According to TEM analyses, the average size range of AgNPs was 17-21nm, and the dominant peaks in the 111°, 200°, 221°, and 311° planes in the XRD pattern indicated the Ag-NPs FCC crystal structure. FTIR data showed that VNE-AgNPs interacted with many reducing, capping, and stabilizing phytochemicals during green synthesis. VNE-AgNPs had higher antibacterial activity against S. aureus and E. coli bacterial strains with a maximum inhibition zone of 21 and 18mm, respectively, than penicillin 5IU, used as a positive control in the study. The cytotoxic effect of VNE-AgNPs appeared at a concentration of 50µg/mL in L929 cells and 5µg/mL in cancer (A549) cells. When the impact of VNE-AgNPs and C-AgNPs on inflammation was compared, it was found that VNE-AgNPs increased TNF-α levels (333.45 ± 67.20ng/mg-protein) statistically (p < 0.05) more than TNF-α levels (256.92 ± 27.88ng/mg-protein) in cells treated with C-AgNPs. VNE-Ag-NPs were found to have a degradation efficiency of 65% against methylene blue (MB) dye within 3h.

By-product Eucalyptus leaves valorization in the basic dye adsorption: kinetic equilibrium and thermodynamic study

Abstract Algerian Eucalyptus Leaves (AEL), a natural biodegradable adsorbent abundantly available, was used for the removal of methylene blue (MB) dye. The AEL properties for the removal of MB were investigated under different conditions by varying the AEL amount, MB concentration, pH of the solution and the reaction temperature. Scanning electron microscopy (SEM) and infrared spectroscopy (FTIR) techniques have been used to characterize AEL biosorbent. Experimental results showed that the adsorption of MB dye at the concentration of 50 mg L−1 reached to 91 % at pH 10 with a stirring speed of 200 rpm and after 180 min of reaction time. The experimental data were analyzed using the linear forms of different kinetic models (pseudo-first order kinetic model, pseudo-second order kinetic model, and intra-particle diffusion models). The results demonstrated that the adsorption kinetics of MB was consistent with the pseudo-second order model with R 2 value of 0.9969. The isotherm models Langmuir, Freundlich, Dubinin, Elovich, Brunaut Emmet Teller and Temkin models were also investigated to describe the adsorption equilibrium. The results show that the AEL adsorption is in accordance with Temkin isotherm. The thermodynamic study revealed that the adsorption is spontaneous and exothermic. Therefore, as a cheap green adsorbent with high MB adsorption performance, AEL is expected to become one of the best candidate materials for future industrial wastewater treatment.

Boosting solar-driven photocatalytic degradation of organic contaminants and bacterial deactivation using marigold- like Cu2O decorated g-C3N4 nanocomposite

Keeping the high efficiency in designing photocatalysts in view, the present work was aimed at the development of a heterojunction photocatalyst with boosted efficiencies, both for degradation of organic contaminants and bacterial deactivation. Heterojunction nanocomposites of g-C3N4 (GCN) and Cu2O (Cu2O /GCN-5 %, Cu2O /GCN-15 %, Cu2O/GCN-25 %, and Cu2O /GCN-50 %) were prepared by hydrothermal method and their photocatalytic performance was evaluated. XPS result confirms the surface chemical composition of nanocomposite and consistent with EDX analysis. The BET studies of Cu2O/GCN −25 % nanocomposite reveals the larger specific surface area (128.10 m2/g), compared to intact Cu2O, which facilitates more active sites on the surface. The optical bandgap energy (2.39 eV-2.58 eV) is tuned towards the visible region by loading g-C3N4 in marigold-like Cu2O. The efficient charge transfer betwixt marigold-like Cu2O and g-C3N4 was demonstrated in PL, CV, and EIS analysis. The Cu2O/GCN-25 % nanocomposite exhibits superior photocatalytic activity towards Aniline blue dye (86.4 %) and β-lactam antibiotic amoxicillin (79 %) under 100 min of sunlight irradiation. HPLC analysis further confirmed the degradation and disintegration of Amoxicillin. The probable photocatalytic mechanism was proposed and tested through a radical scavenger experiment. It was found that ●OH radicals significantly take part in the photodegradation. In addition, the bactericidal activities of Cu2O/GCN-25 % nanocomposite was determined. The highest bactericidal activity was observed for Bacillus subtilis (26 mm). Hence, the marigold-like Cu2O/GCN-25 % nanocomposite is a feasible material for the degradation of dyeing and pharmaceutical industrial effluents as well as bacterial growth inhibition.

Development of 2D/2D h-MoO3/Ag/g-C3N4 heterojunction photocatalyst with enhanced photocatalytic performance for the detoxification of methylene blue and tetracycline under solar light illumination

In this study, direct thermal polycondensation, hydrothermal, and ultrasonic techniques were used to fabricate photocatalysts consisting of bare g-C3N4 (GCN), h-MoO3 (MoO3), MoO3/g-C3N4 (MGCN), and MoO3/Ag/g-C3N4 (MAGCN) composites. These methods were used to improve the photocatalytic effect, especially for environmental applications. The surface and chemical properties of the fabricated samples were investigated by XRD, FT-IR, FE-SEM, HR-TEM, UV-DRS, XPS, and PL analysis. Bare and composite photocatalysts were tested for photodegradation of the methylene blue (MB) dye and tetracycline (TC) antibiotic under solar irradiation. The MAGCN composite material exhibits remarkable efficiency in degrading 99% of MB dye and 90% of TC antibiotic within a time frame of 60 min when exposed to sunlight irradiation. The degradation rate constants (k) of MB and TC in the most active MAGCN photocatalyst were 11.02 and 7.03 times higher than those of pristine GCN, respectively. The scavenger reaction shows that the most important reactive species in the photocatalytic process are superoxide and photogenerated holes. The outstanding photocatalytic efficiency of the MAGCN catalyst was demonstrated by the fact that Ag nanoparticles act as mediators of fast charge transfer, resulting in higher absorption of sunlight, enhanced charge separation/transfer, and regeneration by MoO3 and GCN. The MAGCN photocatalyst exhibits remarkable activity, maintains its performance over six consecutive reaction cycles, and exhibits excellent stability and reusability. Intermediates were analyzed by GC-MS, and suitable degradation pathways were proposed. These results enable the development of an effective Z-scheme heterojunction photocatalyst and facilitate its wide application in the degradation of organic pollutants in wastewater.

Limonia acidissima fruit juice mediated eco-friendly synthesis of pervoskite ZnSnO3 nanoparticles: Applications to photocatalytic, electrochemical, antioxidant and antibacterial activities

In anticipation toa growing desire for start-ups to be both green and sustainable, there has been an increase in research focus on the effective removal and degradation of toxic wastewater effluents. A viable and sustainable wastewater treatment method is the use of light to degrade organic contaminants. Photocatalysis holds great potential for addressing environmental, energy, and health challenges, offering sustainable solutions for a wide range of applications with significant societal and economic benefits. In this paper, a multicomponent heterostructure photocatalyst ZnSnO3 was designed and prepared via a simple environmentally responsible path, which included the use of limonia acidissima natural fruit juice as a capping and reducing agent. The ZnSnO3 nanoparticles that were generated were examined using XRD, FT-IR, UV-DRS, SEM-EDAX, TEM, PL and BET investigations. The structure and crystallographic parameters were examined using XRD analysis, and found that the crystallite had orthorhombic geometry. The functional groups were investigated using FTIR spectroscopy. The band gaps (3.59 & 3.69 eV) were estimated using a Tauc plot employing the data of UV-DRS. According to SEM and TEM studies, the morphologies are irregular in shape and have particles that are about 14 nm in size. EDAX analysis was used to determine the elemental composition of the examined ZnSnO3 nanostructures, which demonstrated their purity. Using PL spectroscopy, superficial defects were investigated. The synthesized NPs were used as photocatalysts to degradethe methylene blue dye. Electrochemical measurement of K3[Fe(CN)6] revealed a good sensory activity with a detection limit of 38 μL. K3[Fe(CN)6] is used to detect ferrous ions in biological specimens. Furthermore, it also shows the superior anti-bacterial activity against gram-positive bacteria such as Staphylococcus aureus, and gram-negative bacteria Pseudomonas fluorescens. To the best of our literature survey, it’s the first report for the synthesis of ZnSnO3 nanostructures using the natural reducing agent limonia acidissima natural fruit juice for dye degradation, electrochemical, anti-oxidant, and anti-bacterial applications.

Design of novel FeSe2/ZnO composites and their application in photodegradation of methylene blue

Water pollution has become one of the major global issues, posing serious threat to both humans and aquatic life. The elimination of organic industrial pollutants from wastewater is currently a major area of research. Herein, we report for the first time a novel FeSe2/ZnO composite system for highly efficient removal of organic dyes under visible light. FeSe2/ZnO composites with varying mass ratios of FeSe2 were successfully prepared through simple and low-cost chemical method. The physiochemical properties of the prepared FeSe2/ZnO composites were carefully evaluated and compared with those of pure ZnO rods and FeSe2 flowers. UV–vis spectroscopy confirmed that the coupling of FeSe2 with ZnO caused a significant improvement in the optical absorption of ZnO. The bandgap energies of FeSe2/ZnO composites showed a red shift with increasing the ratio of FeSe2 flowers. The prepared samples were evaluated for their photocatalytic response against the removal of methylene blue dye. Compared to the pure FeSe2 and ZnO, the composites displayed impressive photocatalytic performance. Among the prepared samples, composite with an optimum ratio of 75 wt% FeSe2 revealed outstanding photocatalytic efficiency, making it a promising candidate for the removal of organic pollutants.

Contrast-enhanced Ultrasound Using Intradermal Microbubble Sulfur Hexafluoride in Non-invasive Axillary Staging in Breast Cancer: Are we Missing a Chance?

In the context of surgical de-escalation in early breast cancer (EBC), this study aimed to evaluate the contrast enhancement ultrasound (CEUS) sentinel lymph node (SLN) procedure as a non-invasive axillary staging procedure in EBC in comparison with standard SLN biopsy (SLNB). A subanalysis of the AX-CES study, a prospective single-arm, monocentric phase 3 study was performed (EudraCT: 2020-000393-20). The study included patients with EBC undergoing upfront surgery and SLN resection, with no prior history of locoregional treatment, and weighing between 40-85 kg. All patients underwent the CEUS SLN procedure as a non-invasive axillary staging procedure, with CEUS SLN accumulation marked using blue dye. After the CEUS SLN procedure, all patients underwent the standard mapping procedure. Data on success rate, systemic reactions, mean procedure time, mean surgical procedure, mean procedure without axillary staging, CEUS SLN appearance (normal/pathological), SLN number, and concordance with standard mapping procedure were collected. After the CEUS SLN procedure, 29 LNs among 16 patients were identified and marked. In all cases, CEUS SLN revealed at least one LN enhancement. Six (37.50%) LNs were defined as pathological after the CEUS SLN procedure. Definitive staining of CEUS SLN pathology revealed metastatic involvement in four (66.67%) of the cases. Two SLNs were identified during the CEUS SLN procedure; however, owing to the low disease burden, no change in the surgical plan was reported. The CEUS SLN procedure shows promise as a technique for non-invasive assessment of the axilla, potentially enabling safe axillary de-escalation in EBC by estimating the axillary disease burden.