Blue Dye Research Articles

Low-cost ceramic membrane production for dye removal

Low-cost ceramic membrane was evaluated on a bench scale, in the separation process of blue methylene dye. Raw materials were characterized by XRD and XRF. The ceramic membrane was produced by dry uniaxial compaction and characterized by XRD, porosity and permeability with pure water. The membrane contains a composition of 65.00 % chocobofe clay, 5.00 % corn starch kaolin, 20.00 % magnesite concentrate and 5.00 % corn starch and sintering temperature of 650 °C. The initial blue methylene dye concentration was 50 mg/L, pressure 2 bar, 25 °C. The low-cost ceramic membrane was effective in separating blue methylene dye, with porosity of 53 % and average pore size of 0.48 µm, as well as pure water flow of 520 L/m2.h. The blue methylene dye rejection was 100.00 %. The membrane reuse demonstrated good performance after 15 cycles. A preliminary costs analysis of the production for low-cost membrane was carried out and the value found was 233.55 $/m2.

Deep Cleaning of Crystal Violet and Methylene Blue Dyes from Aqueous Solution by Dextran-Based Cryogel Adsorbents.

Polysaccharides have recently attracted growing attention as adsorbents for various pollutants, since they can be extracted from a variety of renewable sources at low cost. An interesting hydrophilic and biodegradable polysaccharide is dextran (Dx), which is well-known for its applications in the food industry and in medicine. To extend the application range of this biopolymer, in this study, we investigated the removal of crystal violet (CV) and methylene blue (MB) dyes from an aqueous solution by Dx-based cryogels using the batch technique. The cryogel adsorbents, consisting of cross-linked Dx embedding a polyphenolic (PF) extract of spruce bark, were prepared by the freeze-thawing approach. It was shown that the incorporation of PF into the Dx-based matrix induced a decrease in porosity, pore sizes and swelling ratio values. Moreover, the average pore sizes of the DxPF cryogels loaded with dyes further decreased from 42.30 ± 7.96 μm to 23.68 ± 2.69 μm, indicating a strong interaction between the functional groups of the cryogel matrix and those of the dye molecules. The sorption performances of the DxPF adsorbents were evaluated in comparison to those of the Dx cryogels and of the PF extract. The experimental sorption capacities of the DxPF cryogel adsorbents were higher in comparison to those of the Dx cryogels and the PF extract. The DxPF cryogels, particularly those with the highest PF contents (sample DxPF2), demonstrated sorption capacities of 1.2779 ± 0.0703 mmol·g-1, for CV, and 0.3238 ± 0.0121 mmol·g-1, for MB. The sorption mechanisms were analyzed using mathematical models, including Langmuir, Freundlich, Sips and Dubinin-Radushkevich isotherms, and kinetic models, like pseudo-first-order (PFO), pseudo-second-order (PSO), Elovich and intra-particle diffusion (IPD). The sorption process was best described by the Sips isotherm and PSO kinetic models, indicating chemisorption as the dominant mechanism. This study outlines the importance of developing advanced renewable materials for environmental applications.

Unravelling the tissue regenerative nature of marine polysaccharide chitosan embedded halloysite reinforced poly (vinyl alcohol) nanocomposite films

The study focuses on developing the poly (vinyl alcohol) (PVA) nanocomposite films reinforced with Halloysite Nano-Tubes (HNT) which were surface functionalised with chitosan forming a Schiff base structure. The work was aimed to traverse its way in tissue engineering. Modification of halloysite with sea polysaccharide chitosan enhanced its ability to bind to the PVA matrix. The modification was assisted by FTIR, XRD, FESEM, TEM, AFM and DSC-TGA techniques. The films could withstand a higher temperature and exhibited high ranges of tensile strength and Young’s modulus. In addition, biocompatible studies such as in-vitro swelling, enzymatic degradation, water contact angle and hemolysis presented extremely well compatibilities proving it to be viable in physiological pH (in phosphate buffered saline). The cell adhesion and proliferation studies conducted on NIH3T3 mouse fibroblasts revealed the cell proliferation and tissue regeneration properties of the films. Both the tests performed for cell growth- Trypan blue dye exclusion and Acridine Orange Ethidium bromide assays showed a doubled rate of cell growth on the films which proves its biomedical nature.Graphical

The effects of intraoperative use of blue dyes in pediatric pilonidal sinus disease—a retrospective exploratory cohort study

BackgroundIntraoperative use of methylene blue has been shown to reduce postoperative complications and recurrence rates in adults. It has however not been assessed if these beneficial effects would also apply to pediatric pilonidal sinus disease with its high recurrence rates. We, therefore, aimed to assess its effects on complications and recurrences in our retrospective exploratory cohort study.MethodsOf 55 consecutive children treated in our centre between January 2009 and December 2020, 48 were retrospectively included. We used logistic regression with a priori chosen predictors of intraoperative use of blue dyes, previous surgery for pilonidal sinus disease, and the presence of comorbidities on the composite outcome of complications and recurrence. Cramér’s V was used to explore associations between the use of blue dyes and the extent of resection.ResultsThe median age in our cohort was 15.3 years. Five patients were below 2 years of age, and 24 (50%) of them were males. Chronic diseases were present in 13 (27%) patients, eight had previously been operated on for pilonidal sinus disease, and blue dyes were used in 34 patients (71%). Their intraoperative use was linked to the composite outcome with an odds ratio of 5.41 (95% confidence interval (CI) 1.52–25.34, P = 0.017) as were comorbidities with an odds ratio of 1.86 (95% CI 1.18–3.25, P = 0.014), but not re-do surgery (odds ratio 2.94 (95% CI 0.37 23.42, P = 0.3)). The use of blue dyes was associated with larger resections (Cramér’s V 0.556 (95% CI 0.329–0.74)).ConclusionThe intraoperative use of blue dyes was negatively associated with complications and recurrences in pediatric pilonidal sinus disease. However, if blue dyes were used, the extent of resection was also larger. Larger resections had been shown before to be associated with complications and recurrences, too. This potential interaction requires further elucidation in future studies.

Enhanced piezocatalytic degradation of cationic dyes using graphene oxide and magnetic beads Nanomaterials: Synthesis, Characterization, and mechanistic insights

Sequestration of organic pollutants by the method of degradation is one of the safest ways to completely remove them from water bodies, without generating harmful by-products. Piezocatalytic degradation for this approach has been gaining much research attention, in recent times, due to its high efficiency. The present work reports synthesis of four types of Graphene Oxide-Chitin-Magnetic Iron Oxide Beads Nanomaterials, each with a different ratio of Graphene oxide (GO) and Chitin (CH). Among these, GO-CH-MIOBs NM-4 showed a superior Piezocatalytic degradation capacity towards methylene blue (MB), crystal violet (CV) and Rhodamine 6G (R6G) dyes. Various parameters influencing the piezocatalytic performance of the material such as kinetic factors, initial dye concentration, strength of ultrasonic vibration etc., have been analyzed thoroughly. Degradation rate constant (K) values of 63.4, 59.34 and 48.36 /min were obtained for MB, CV and R6G Dyes respectively. Moreover, cycling tests for all three dyes reflected significant stability of these materials as evident from the high degradation efficiencies of 99.80, 99.24 and 99.12 % within 60 min being retained for MB, CV and Rh6G dyes even after the 5th cycle. These nanomaterials can be a good addition in the list of high efficiency piezocatalyts for water purification with no secondary wastes being produced. Comparison of the XPS spectra before and after sonication gave insight into the mechanism of piezocatalytic degradation which highlighted hydroxyl and superoxide radicals as the main attacking species which are responsible for the degradation process.

Microplastics and dye removal from textile wastewater using MIL-53 (Fe) metal-organic framework-based ultrafiltration membranes

Microplastics (MPs) and other organic matters in textile wastewater have posed a formidable challenge for treatment processes, particularly in the primary stages such as ultrafiltration (UF). UF plays a crucial role in preventing the entry of pollutants into subsequent treatment steps. However, the performance efficiency of UF membranes is compromised by the potential fouling of membrane pores by MPs, dyes and other organic pollutants such as bovine serum albumin (BSA). This study focuses on enhancing UF membrane performance, specifically its antifouling properties, through the development of high-performance membranes using MIL-53(Fe) metal-organic framework (MOF) particles (noted as MIL-53 here). Various concentrations of the MIL-53 (0.05, 0.1, 0.2, and 0.5 wt%) were integrated into the membrane structure through phase inversion process. Streaming zeta potential results confirmed the negatively charged surface of the membranes and their high hydrophilicity was validated through contact angle analysis. FTIR, SEM, EDS, and XRD confirmed the presence of MIL-53 particles on the surface of membranes. The developed membranes were tested for 24 h to assess their antifouling properties, with a subsequent 30-min hydraulic flush to measure their flux recovery ratios. Methylene Blue (MB) dye was used as a cationic dye present in textile wastewater to evaluate the efficiency of the developed membranes in dye removal and the synergistic effects of dye rejection in the presence of organic matters (i.e., MPs and BSA). Since previous studies have not fully addressed the combination of dyes and organic matter, this study thoroughly investigated the effect of particle-type foulants (MPs) and their interactions with dye (MB), as well as water soluble protein-type foulants (BSA) and their interaction with MB. The results indicated that the developed membranes exhibited higher MB rejection when the dye was present with either MP or BSA, along with improved antifouling properties. The optimised UF membrane integrated with 0.1 wt% MIL-53 demonstrated nearly 96% BSA rejection and around 86% MB rejection in the mixed foulant case (BSA-MB). The modified membrane exhibited a substantial increase in water flux from 176 L m−2.h−1 to 327 L m−2.h−1. The findings of this research show the potential of iron-based MOFs in improving the performance of UF membranes and provide a platform for future studies on significant areas such as long-term stability studies and testing with other pollutants found in textile wastewater.

Anti-cancer and visible-light-driven photocatalyst activities of graphene oxide nanosheets against A549 lung cancer cells and organic dyes

The use of graphene oxide (GO) nanosheets (NSs) in cancer cell treatment is a promising and innovative approach to eradicate lung cancer cells and to adsorb and photodegrade organic dyes in water. XRD results revealed that the produced GO NSs have a high crystallinity and a d-spacing value of 0.87 nm. The FTIR spectrum showed that several oxygen-containing functional groups were introduced at the graphite surface from the exfoliation process. The TGA curve result supported the synthesis of GO NSs from the characteristic weight loss behavior. The wrinkled and fold surface morphology of the synthesized GO NSs was confirmed using FE-SEM and TEM. Subsequently, the assessment of their in vitro anti-oxidant and hydroxyl radical scavenging characteristics revealed that the synthesized GO NSs possessed effective antioxidant properties. The viability of A549 lung cancer cells against GO NSs was found to decrease in a dose-dependent manner and their morphology and nuclear damages was assessed by AO/EB and DAPI staining assays. The increased oxidative stress resulted in greater apoptotic cell death, loss of nuclear integrity, and mitochondrial membrane damage against A549 lung cancer cells. The increasing caspase-3 and caspase-9 activation resulted in more apoptotic cell death and cell cycle arrest as determined by flow cytometry. Further, GO NSs demonstrated moderate photocatalytic activity under visible light irradiation, degrading methylene blue (MB) and bromothymol blue (BTB) dye molecules by 44 and 53.5 %, respectively, after 120 min irradiation. Finally, the present study demonstrated that GO NSs possess excellent anti-cancer and moderate photocatalyst activities.

Analysing the efficacy of TiO2/g-C3N4 nanohybrid electrospun membranes for visible-light photocatalytic water purification

The significance and reliability of membrane-based water purification in wastewater recycling are emphasized in this study. Hydrophilic cellulose acetate and hydrophobic polycaprolactam membranes incorporated with TiO2/g-C3N4 nanohybrids were fabricated by electrospinning. Synthesis of TiO2/g-C3N4 nanohybrids employed a sol–gel-assisted hydrothermal method, while g-C3N4 through fractional thermal polymerization of acetic acid-modified melamine. The optimized photocatalytic hybrid exhibited methylene blue degradation by a 1.5-fold increase in photoactivity compared to pristine TiO2 and a 3-fold increase compared to g-C3N4. Upon incorporation into electrospun membranes, the hybrids demonstrated effective degradation of Methylene blue dye by photocatalysis, and the membranes exhibited excellent stability over multiple cycles.

Photocatalytic activity (dye degradation) of pristine and doped LaFeO3 (dopant Y at a site and Ni at B site) by impedance spectroscopy

Lanthanum iron oxide (LaFeO3) nanoparticles, doped with yttrium (Y) at the A-site and nickel (Ni) at the B-site, were synthesized using a sol-gel method at 600 °C. This study focuses on the synthesis of nanocrystalline La1−xYxFeO3 (Y doped LaFeO3), LaFe1−xNixO3 (Ni doped LaFeO3) and La1−xYxFe1−xNixO3 (Y/Ni doped LaFeO3) materials, where x = 0.01. The Synchrotron-based XRD analysis confirmed the single-phase formation of orthorhombic LaFeO3 (Pbnm space group) in each sample. The characterization through scanning electron microscopy and EDX revealed grains of irregular shape with an average particle size of around 200 nm. Optical properties were explored using UV–Visible spectroscopy, indicating a band gap of 1.7 eV for the pure sample. Additionally, the photocatalytic properties of the synthesized nanoparticles were evaluated for dye degradation. Electrical properties were systematically examined using impedance spectroscopy across a frequency range of 1 Hz–10 MHz at room temperature. The effect of doping on crystal structure and possible implications on dielectric and photocatalytic properties were studied. The complex impedance diagram displayed a depressed semicircle, suggesting non-Debye relaxation processes. A correlation was established between impedance and UV–Vis spectroscopy. However, the current literature lacks a comprehensive investigation for isovalent i.e. +3 substitution at A and B site simultaneously for dye degradation properties of LaFeO3-based materials. This study addresses this research gap by systematically exploring the influence of separate as well as simultaneous Y+3 and Ni+3 doping on the structural, optical, electrical, and photocatalytic characteristics of LaFeO3 nanoparticles, thereby providing valuable insights for the development of advanced functional materials for environmental applications. It was found that Y+3 dopants had a notable impact on the dye degradation properties for Mythlene blue dye at room temperature.

Assessment of microbial safety of fresh vegetables through Caenorhabditis elegans model

Caenorhabditis elegans is widely used as a model to predict the virulence of animal-origin human pathogens, as C. elegans and humans share similar intestinal epithelial cells. A study was undertaken to assess the feasibility of C. elegans for surveillance of foodborne pathogens in fresh vegetables. First, the virulent strains of four foodborne pathogens viz., Pseudomonas aeruginosa (PAO1), Escherichia coli (O157), Salmonella enterica (CI1), and Staphylococcus aureus (ATCC25923) were fed to the worm as sole diet and compared the survival, phenome traits, and gut integrity with standard E. coli OP50. Secondly, the vegetable surface microbiota (tomato) was enriched with gradient concentrations of PAO1, and the worm's survival and gut distension and leakage were assessed. Thirdly, the total microbiota of fresh vegetables (tomato, brinjal, and lablab) were evaluated for the worm's survival. The gut epithelial cell damage and leakage were monitored by blue dye-based smurf assay. Foodborne pathogens reduced the median lifespan (LT50) of the worm drastically, with PAO1 had 2.5 days, O157 (6 days), CI1 (8 days), ATCC25923 (6 days), while the standard diet OP50 had 16 days. The phenome traits of worms, viz., pharyngeal pumping, defecation cycle, body bends, head thrashes, touch stimulus, paralysis, gut leakage, and reproduction, were significantly negatively affected due to pathogen feeding. The gut epithelial integrity was severely affected, and blue dye leakage was the highest in O157 (73 %), followed by PAO1 (55 %), CI1 (40 %) and ATCC25923 (38 %), while the gut epithelial cells were intact in OP50 fed worms. The pathogen enrichment in tomato surface microbiota diet showed that LT50 of the worms was reduced from 8 days to 2.5 days and 10 to 8 days with increasing gradient of PAO1 in fresh tomato microbiota and 24-hours pre-enriched tomato microbiota, respectively. Smurf test also confirmed that an increase in PAO1 proportion in total microbiota distended the gut with high dye leakage. The total microbiota extracted from tomato, brinjal, and lablab did not affect the worm's health and had an extended median life span (11 – 13 days) when they were devoid of any foodborne pathogens. These findings provide a novel and straightforward approach for assessing foodborne pathogens using animal models.

Selective adsorption of methylene blue dye by a flocculation sludge-derived adsorbent prepared by carboxymethyl chitosan-based flocculants

The flocculation of dyeing wastewater generated a large amount of sludge that was often disposed as refractory hazardous waste. The resource utilization of flocculation sludge was of great significance in terms of low treatment cost of sludge, low environmental risk and high usage efficiency of reactive dyes. Herein, a flocculation sludge-derived (FSD) adsorbent was prepared via cross-linking of flocculation sludge yielding by carboxymethyl chitosan-based flocculants and dyes. FSD adsorbent had excellent selective adsorption performance for methylene blue (MB) treatment. The highest removal rate of MB and adsorption capacity of FSD adsorbent were 96.48 % and 354.7066 mg/g, attributing to its rich functional groups, negative charges and special micropore structure. FSD adsorbent owned the favorable regeneration efficiency and stability. Its removal rate of MB was still above 71.8 % after 6 regeneration-adsorption cycles. Its leaching rate of dyes was only 0.0016 mg/mg that was rather lower than common dried flocculation sludge. The adsorption processes of FSD adsorbent were complex in accordance with its characteristics, adsorption isotherms, adsorption kinetics and theoretical calculation. Multiple adsorption mechanisms were present in the treatment of dyeing wastewater by FSD adsorbent. The resource utilization of flocculation sludge, as adsorbents, was a potential candidate in field application.

Dynamic intercalation of methylene blue in BC-MgFe-HT composite: Unveiling adsorption mechanisms for efficient wastewater treatment

Developing efficient and eco-friendly adsorbents for removing dye from wastewater presents a significant challenge. In this study, by combining MgFe-hydrotalcite (MgFe-HT) with bamboo charcoal (BC) we report the synthesis of a composite material named BC-MgFe-HT to achieve rapid and effective adsorption of methylene blue (MB) dye. The novelty of our work lies in the distinctive intercalation arrangement of the MB dye post-adsorption within the BC-MgFe-HT layers, which was quantitatively measured and found to be at an intercalation angle of approximately 44.26° rather than the conventional vertical positioning. This unique phenomenon indicates a dynamic rearrangement of the composite structure upon MB adsorption, significantly enhancing its adsorption capacity and efficiency. Comprehensive characterization of the BC-MgFe-HT composite was performed using the following techniques such as X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), Brunauer–Emmett–Teller (BET) surface area analysis, and thermogravimetric analysis (TGA). The adsorption studies demonstrated a maximum adsorption capacity of 194.09 mg/g within 20 min, attributed to the composite's high surface area, porous architecture, and dye intercalation capacity. Kinetic studies revealed that the pseudo-second-order (PSO) kinetics model best describes the adsorption process, while the Langmuir isotherm model provided the most accurate fit for the adsorption equilibrium data. These findings offer novel insights into the adsorption mechanisms of MB onto the BC-MgFe-HT composite, highlighting its potential for the design and optimization of composite materials for effective wastewater remediation.

Facile construction of efficient WO3/V2O5 coupled g-C3N4 ternary composite photocatalyst for environmental emergent aqueous pollutant degradation: Stability, degradation reaction pathway and effect of pH evaluation.

Currently, one of the primary challenges that human society must overcome is the task of decreasing the amount of energy used and the adverse effects that it has on the environment. The daily increase in liquid waste (comprising organic pollutants) is a direct result of the creation and expansion of new companies, causing significant environmental disruption. Water contamination is attributed to several industries such as textile, chemical, poultry, dairy, and pharmaceutical. In this study, we present the successful degradation of methylene blue dye using g-C3N4 (GCN) mixed with WO3 and V2O5 composites (GCN/WO3/V2O5 ternary composite) as a photocatalyst, prepared by a simple mechanochemistry method. The GCN/WO3/V2O5 ternary composite revealed a notable enhancement in photocatalytic performance, achieving around 97% degradation of aqueous methylene blue (MB). This performance surpasses that of the individual photocatalysts, namely pure GCN, GCN/WO3, and GCN/V2O5 composites. Furthermore, the GCN/WO3/V2O5 ternary composite exhibited exceptional stability even after undergoing five consecutive cycles. The exceptional photocatalytic activity of the GCN/WO3/V2O5 ternary composite can be ascribed to the synergistic effect of metal-free GCN and metal oxides, resulting in the alteration of the band gap and suppression of charge recombination in the ternary photocatalyst. This study offers a better platform for understanding the characteristics of materials and their photocatalytic performance under visible light conditions.

In-situ halloysite functionalization of anionic hybrid gels possessing easily implemented site-specific (alkyl)amide and carboxyl groups

Design of functional materials with tunable properties based on anionically-modified copolymer network of poly (N-isopropyl acrylamide-co-methacrylic acid) P(NIPA-co-MA) containing linear polyacrylamide and various amounts of Halloysite nanotubes (Hal) was presented using a facile route of solution casting. The organic/inorganic nanostructures based on thermo-responsive PNIPA were constructed to create hybrid materials via in situ polymerization with different Hal-loading and then used for the removal of cationic methylene blue (MB) dye from aqueous solutions. To achieve the desired mechanical property, the optimum composition of hybrids was determined following a simple and cost-effective synthesis procedure. In situ one-pot polymerization was promoted by semi-IPN formation, following a much simpler route than traditional preparation approaches for stable cross-linked hybrid formation. The swelling of hybrids decreased by 2.9-fold with loading of 5.40 % Hal, confirming the hydrogen bonding interactions between Hal and PAAm/P(NIPA-co-MA) network. The mechanical properties of Hal-doped hybrid gels showed an increase–decrease tendency with increase of Hal-content from 0.80 to 5.40 % (w/v) due to the high aspect ratio of Hal and strong secondary interactions between Hal and PAAm/P(NIPA-co-MA) chains. The effective cross-link density for Hal-doped hybrids was expressed by a cubic polynomial as a function of Hal concentration. Temperature-sensitive swelling results showed that the advantage of sustained release property of Hal can be combined with excellent controllability of PNIPA-based network. Adsorption results of MB onto Hal-doped hybrids bearing methacrylic acid moieties demonstrated their potential as efficient adsorbents for the removal of cationic dyes. A new route offered by the proposed procedure for design of hybrids containing “green” one-dimensional nanofillers creates an innovative perspective on robust hybrid structures for practical applications.

Synthesis, characterization and correlation studies on the Ni–Zn–Mn ferrite as a photocatalyst

Samples of Ni0.3Zn0.7−xMnxFe2O4 (x = 0, 0.15, 0.25, 0.35, 0.45, 0.55) nanoparticles (NPs) were synthesized by auto-combustion flash method. These ferrites were used as catalysts for photodegradation of methylene blue (MB) dye utilizing visible light energy. Structural analysis was carried out using the X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy, while nanoparticle dimensions were elucidated through transmission electron microscopy (TEM). The magnetic and optical behaviours were unveiled via vibrating sample magnetometer and UV–VIS spectroscopy, respectively. The XRD outcomes established the presence of a cubic spinel-type structure for the studied ferrite samples. The FTIR spectra unveiled two absorption characteristic bands of the spinel ferrite. TEM images revealed nanoscale dimensions of ferrite NPs with the range from 21.1 to 51.8 nm. The optical features exhibited an indirect band gap energy spanning from 4.25 to 4.36 eV. Magnetization behaviour displayed a sinusoidal trend corresponding to varying Mn concentrations. The ferrite NPs catalyst (10 mg) yield photodegradation efficiency ranged from 22.8 to 33.9% for 100 ml MB dye solution after 120 min of light irradiation. The effects of dye concentration and catalyst dose on the degradation efficiency were examined using the Ni0.3Zn0.35Mn0.35Fe2O4 catalyst with highest degradation (= 33.9%). On the other hand, the dependence of the degradation efficiency on the structure, morphological, magnetic and optical properties of the photocatalyst was investigated. The findings of this study underscore the potential of the prepared ferrite nanoparticles for advanced applications in environmental restoration.Graphical abstract

Protective Effects of Chitosan-Loaded Pomegranate Peel Extract Nanoparticles on Infertility in Diabetic Male Rats.

Diabetes Mellitus (DM) is known to have an impact on the health of the male reproductive system. It is linked to low sperm quality, increased oxidative stress, and an increased generation of reactive oxygen species in the seminal fluid. Pomegranate extract has phenolic compounds and significant protective properties against oxidative stress, male sex hormone disruptions, and sperm abnormalities. The current study aimed to evaluate the effectiveness of Pomegranate Peel Extract Nanoparticles (PPENPs) on male fertility in diabetic rats. DM was induced in rats by intraperitoneal injection of streptozotocin (60 mg/kg). Twenty-four rats were divided into four groups, 6 rats in each group: control, DM, DM+empty NPs (60 mg/kg, orally), and DM+PPENPs (60 mg/kg, orally). Administration of PPENPs increased the levels of insulin, FSH, LH, testosterone, catalase, glutathione reduced, and semen fructose. PPENPs also improved sperm quality, as seen by improvements in sperm morphology, motility, count, and the ability of metabolically active spermatozoa to convert blue resazurin dye to pink resorufin. However, PPENPs decreased levels of glucose, malonaldehyde, nitric oxide, and sperm abnormalities. Also, histological investigation of the PPENPs showed improvement in testis tissue architecture and increased the diameter size of seminiferous tubules and germinative layer thickness. Our investigation proved that the treatment of PPENPs has a protective effect on the reproductive system of male diabetic rats, improving fertility parameters, healthy sperm profiles, and the antioxidant system.

Structural, optical and morphological properties of Eu rare earth doped WO3 nanoparticles enhanced photocatalytic for waste water treatment and antibacterial activities

In this paper, summarise the characterization and synthesis of the pure and Eu:WO3 nanoparticles and their applications in photocatalytic and antibacterial activity. The monoclinic phase confirmed by the XRD analysis of the prepared specimens. SEM and HR-TEM scrutiny revealed nanoplate morphology scrutiny. EDS and XPS scrutiny confirmed the composition of elements of Eu, O, and W. FTIR analysis likely used for additional confirmation of functional groups. UV–Vis Analysis determined the band gap energy (Eg) of the nanoparticles, which decreased with raising the concentration of Eu doping. Optical properties of the band gap energy decreased with raising the concentration of Eu doping. Photocatalytic activity of the nanoparticles exhibited high photocatalytic activity, with a 95.3 % methylene blue (MB) dye split when exposed to visible light. The Eu:WO3 (7 wt%) nanoparticles showed the best photocatalytic property within 120 min. The Eu:WO3 (7 wt%) nanoparticles showed the maximum antibacterial efficiency against Staphylococcus aureus, with a zone of embarrassment of 19 mm. Overall, the study demonstrates the successful synthesis of Eu-doped WO3 nanoparticles and their potential applications in photo catalysis and antibacterial activity, with promising results particularly at higher Eu doping concentrations.

Dye Removal From Tannery Wastewater Utilizing Footwear Waste: A Sustainable Approach

ABSTRACTWaste‐to‐3R (reduce, reuse, and recycle) is a promising mass balance approach in the leather sector for addressing the current challenge of overproduction of rubber sole waste in the footwear industry and dye pollution in tanneries. In this study, low‐cost charcoal derived from discarded natural rubber (NR) soles was effectively employed to remove anionic and cationic dyes from a model tannery dye solution, aligning with mass balance approaches in the leather sector. Discarded rubber charcoal (DRC) was prepared at 350°C using a self‐fabricated pyrolytic cell. The resulting charcoal was then dried, ground, and separated through 40‐mesh size lab‐scale sieves, and it was subsequently employed for the removal of dyes from tannery wastewater. The dye removal performance was optimized by adjusting parameters such as dosage, pH, contact time, and concentration. The maximum adsorption capacity and removal efficiency of the anionic acid dye (AD) were found to be 158.22 mg/g and 88.39% at pH 1, respectively, while those of the cationic methylene blue dye were 166.18 mg/g and 85.53% at pH 12, respectively, between 15 and 30 min, depending on the DRC conditions. Fresh charcoal and dye‐loaded charcoal were characterized through Fourier transform infrared spectroscopy, x‐ray diffraction, Brunauer–Emmett–Teller, scanning electron microscope (SEM), and transmission electron microscope with Energy‐Dispersive X‐ray (EDX) Spectroscopy for respective functional groups and morphology studies, and zeta potential measurements were employed to characterize the charcoal surface charge. The SEM image revealed that the shape of the DRC particles resembles a honeycomb structure, with an average size of 573.56 µm. The adsorption kinetic study indicates that the Freundlich isotherm model and pseudo‐second‐order kinetics were well‐fitted for dye removal in this study. The charcoal exhibited robust stability, retaining its capacity of 57.42 mg/g of AD and 44.94 mg/g of MB dye after four reuse cycles. This resilience was observed in treatment with various desorption agents, including HCl, CH3COOH, NaOH, and C2H5OH. The findings of this study suggest that NR‐derived charcoal could be used as a successful substitute for commercial activated carbon in wastewater treatment to get rid of the acid and basic dyes of the leather industry. Based on the observed results, a plausible mechanism was also proposed.

Removal of hazardous Aniline Blue dye using a potential Biosorbent – Hen feather

In this research we have successfully removed a highly toxic dye, “Aniline Blue”, from its aqueous solution employing an adsorbent, Hen Feathers. The dye adsorption over Hen Feather was comprehensively studied over ranges of contact time, pH, concentration, and adsorbent dosage, and the optimum values were evaluated. In order to understand the behaviour of the adsorption system, various isotherm models were evaluated at temperatures of 30, 40 and 50 °C. The data obtained from contact time studies were used to test pseudo-first and pseudo-second order kinetic models and it was found that the adsorption follows pseudo-second-order kinetics. Using the Langmuir constant, b, thermodynamic parameters including ΔG°, ΔH° and ΔS° were calculated and it was ascertained that the process is endothermic (positive ΔH°), involves an increase in disorder (positive ΔS°) and is spontaneous (negative ΔG°). The values of the separation factor (r) also confirmed a favourable adsorption process at all three temperatures studied. Overall, it is affirmed that the adsorbent, Hen Feather, acts as highly potent scavenger to remove the dye Aniline Blue from its aqueous solutions.

Eco-friendly synthesis of CuO/NiO nanocomposite and their enhanced photocatalytic organic dyes degradation, antimicrobial, cytotoxicity and antioxidant applications

In this study, Macroptilium lathyroides leaf extract was used as a reducing and capping agent to prepare the biogenic CuO-NiO nanocomposite. The synthesized samples were analyzed using UV–visible spectroscopy, Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), High-resolution transmission electron microscopy, X-ray photoelectron spectroscopy (XPS), Scanning electron microscopy with energy-dispersive X-ray (EDX) analysis, Dynamic light scattering, and Zeta potential. The structure, surface morphology, elemental compositions, and stability of the particles were determined. The average size of the particles from TEM was found to be 10.6 nm with a cubic structure. Furthermore, CuO-NiO nanocomposite was used to study the methylene blue dye degradation when exposed to sunlight for 90 min, about 98.1 % of the dye degraded. The nanocomposite showed high antimicrobial activity against both Gram-positive bacteria Staphylococcus aureus (18 mm), Streptococcus pyogenes (20 mm) and Gram-negative strains Klebsiella pneumonia (16 mm), Escherichia coli (18 mm) at 30 µg/mL. The antifungal activity against Trichoderma viride (14 mm), Candida albicans (13 mm) and excellent antioxidant properties with an IC50 value of 184.52 µg/mL were observed. Furthermore, it shows potent cytotoxic effects against the lung cancer cell line A549, and breast cancer cell line MCF 7 with an IC50 value of 59.8 µg/mL, 42.90 µg/mL, respectively.