Biomimetic Topography Research Articles

Synergistic integration of plant derived galactomannan and MXene to produce multifunctional nanocomposites with antibacterial and osteogenic properties

This study proposes to combine plant-derived galactomannan and MXene to form an organic-inorganic hydrogel network with integrative antibacterial and osteogenic properties. Oxidized galactomannan (OxGa) was blended with N-succinyl chitosan (NSC) and varying concentrations of Mxene, owing to its high reactivity and biocompatibility. The results indicated that Mxene-loaded OxGa/NSC scaffolds exhibited biomimetic topography, adequate mechanical features and excellent physicochemical properties with strong antibacterial properties against pathogenic microbes. The cell culture experiments showed dose-dependent cytotoxic behaviour. An optimized MXene content of ≤ 4 mg/ml revealed no cytotoxicity and augmented the proliferation of osteoblast cells. Similar results were obtained in gene expression analysis where ALP, COL1A1, RUNX2, and SOX2 genes showed up-regulation. In addition, the chorioallantoic membrane (CAM) assay also illustrated augmentation of angiogenesis without any toxicity. The overall results highlight the dual performance of OxGa/NSC-MXene scaffolds to exhibit anti-infection with simultaneous osteogenic properties, which is purely determined by the concentration of MXene. Therefore, regulating MXene concentration can serve as a chemical switch in imparting adequate antibacterial functions with the ability to allow new osseous generation. Our findings on the newly designed Mxene-loaded OxGa/NSC scaffolds can be a promising biomaterial for bone-related infections with a concurrent ability to promote osteogenesis.

The Effects of Biomimetic Surface Topography on Vascular Cells: Implications for Vascular Conduits.

Cardiovascular diseases (CVDs) are the leading cause of mortality worldwide and represent a pressing clinical need. Vascular occlusions are the predominant cause of CVD and necessitate surgical interventions such as bypass graft surgery to replace the damaged or obstructed blood vessel with a synthetic conduit. Synthetic small-diameter vascular grafts (sSDVGs) are desired to bypass blood vessels with an inner diameter <6 mm yet have limited use due to unacceptable patency rates. The incorporation of biophysical cues such as topography onto the sSDVG biointerface can be used to mimic the cellular microenvironment and improve outcomes. In this review, the utility of surfacetopography in sSDVG designis discussed. First, the primary challenges that sSDVGs face and the rationale for utilizing biomimetic topography are introduced. The current literature surrounding the effects of topographical cues on vascular cell behaviorin vitrois reviewed, providing insight into which features are optimal for application in sSDVGs. The results of studies that have utilized topographically-enhanced sSDVGs in vivo are evaluated. Current challenges and barriers to clinical translation are discussed. Based on the wealth of evidence detailed here, substrate topography offers enormous potential to improve the outcome of sSDVGs and provide therapeutic solutions for CVDs.

Different Methods to Modify the Hydrophilicity of Titanium Implants with Biomimetic Surface Topography to Induce Variable Responses in Bone Marrow Stromal Cells.

The osteoblastic differentiation of bone marrow stromal cells (bMSCs), critical to the osseointegration of titanium implants, is enhanced on titanium surfaces with biomimetic topography, and this is further enhanced when the surfaces are hydrophilic. This is a result of changing the surface free energy to change protein adsorption, improving cell attachment and differentiation, and improving bone-to-implant contact in patients. In this study, we examined different methods of plasma treatment, a well-accepted method of increasing hydrophilicity, and evaluated changes in surface properties as well as the response of bMSCs in vitro. Commercially pure Ti and titanium-aluminum-vanadium (Ti6Al4V) disks were sand-blasted and acid-etched to impart microscale and nanoscale roughness, followed by treatment with various post-processing surface modification methods, including ultraviolet light (UV), dielectric barrier discharge (DBD)-generated plasma, and plasma treatment under an argon or oxygen atmosphere. Surface wettability was based on a sessile water drop measurement of contact angle; the elemental composition was analyzed using XPS, and changes in topography were characterized using scanning electron microscopy (SEM) and confocal imaging. The cell response was evaluated using bMSCs; outcome measures included the production of osteogenic markers, paracrine signaling factors, and immunomodulatory cytokines. All plasma treatments were effective in inducing superhydrophilic surfaces. Small but significant increases in surface roughness were observed following UV, DBD and argon plasma treatment. No other modifications to surface topography were noted. However, the relative composition of Ti, O, and C varied with the treatment method. The cell response to these hydrophilic surfaces depended on the plasma treatment method used. DBD plasma treatment significantly enhanced the osteogenic response of the bMSCs. In contrast, the bMSC response to argon plasma-treated surfaces was varied, with an increase in OPG production but a decrease in OCN production. These results indicate that post-packaging methods that increased hydrophilicity as measured by contact angle did not change the surface free energy in the same way, and accordingly, cells responded differently. Wettability and surface chemistry alone are not enough to declare whether an implant has an improved osteogenic effect and do not fully explain how surface free energy affects cell response.

Synergistic effect of hierarchical topographic structure on 3D-printed Titanium scaffold for enhanced coupling of osteogenesis and angiogenesis

The significance of the osteogenesis-angiogenesis relationship in the healing process of bone defects has been increasingly emphasized in recent academic research. Surface topography plays a crucial role in guiding cellular behaviors. Metal-organic framework (MOF) is an innovative biomaterial with nanoscale structural and topological features, enabling the modulation of scaffold physicochemical properties. This study involved the loading of varying quantities of UiO-66 nanocrystals onto alkali-heat treated 3D-printed titanium scaffolds, resulting in the formation of hierarchical micro/nano topography named UiO-66/AHTs. The physicochemical properties of these scaffolds were subsequently characterized. Furthermore, the impact of these scaffolds on the osteogenic potential of BMSCs, the angiogenic potential of HUVECs, and their intercellular communication were investigated. The findings of this study indicated that 1/2UiO-66/AHT outperformed other groups in terms of osteogenic and angiogenic induction, as well as in promoting intercellular crosstalk by enhancing paracrine effects. These results suggest a promising biomimetic hierarchical topography design that facilitates the coupling of osteogenesis and angiogenesis.

Titanium surfaces with biomimetic topography and copper incorporation to modulate behaviors of stem cells and oral bacteria.

Purpose: Insufficient osseointegration and implant-associated infection are major factors in the failure of Ti-based implants, thus spurring scientists to develop multifunctional coatings that are better suited for clinical requirements. Here, a new biomimetic micro/nanoscale topography coating combined with antibacterial copper was simultaneously designed for Ti-based implant surfaces by adopting a hybrid approach combining plasma electrolytic oxidation and hydrothermal treatment. Results: The biological interactions between this biofunctionalized material interface and stem cells promoted cellular adhesion and spreading during initial attachment and supported cellular proliferation for favorable biocompatibility. Bone marrow mesenchymal stem cells (BMMSCs) on the coating displayed enhanced cellular mineral deposition ability, higher alkaline phosphatase activity, and upregulated expression of osteogenic-related markers without the addition of osteoinductive chemical factors, which improved osseointegration. More interestingly, this new coating reduced the viability of oral pathogens (Fusobacterium nucleatum and Porphyromonas gingivalis)-the primary causes of implant-associated infections as indicated by damage of cellular structures and decreased population. This is the first study investigating the antibacterial property of dental implants modified by a hybrid approach against oral pathogens to better mimic the oral environment. Conclusion: These findings suggest that biofunctionalization of the implant coating by surface modification methods and the incorporation of antibacterial copper (Cu) offer superior osteogenesis capability and effective antibacterial activity, respectively. These strategies have great value in orthopedic and dental implant applications.

The biomimetic surface topography of Rubus fruticosus leaves stimulate the induction of osteogenic differentiation of rBMSCs

The interaction between cells and biomaterials is essential for the success of biomedical applications in which the implantation of biomaterials in the human body is necessary. It has been demonstrated that material’s chemical, mechanical, and structural properties can influence cell behaviour. The surface topography of biomaterials is a physical property that can have a major role in mediating cell–material interactions. This interaction can lead to different cell responses regarding cell motility, proliferation, migration, and even differentiation. The combination of biomaterials with mesenchymal stem cells (MSCs) for bone regeneration is a promising strategy to avoid the need for autologous transplant of bone. Surface topography was also associated with the capacity to control MSCs differentiation. Most of the topographies studied so far involve machine-generated surface topographies. Herein, our strategy differentiates from the above mentioned since we selected natural surface topographies that can modulate cell functions for regenerative medicine strategies. Rubus fruticosus leaf was the selected topography to be replicated in polycaprolactone (PCL) membranes through polydimethylsiloxane moulding and using soft lithography. Afterwards, rat bone marrow stem cells (rBMSCs) were seeded at the surface of the imprinted PCL membranes to characterize the bioactive potential of our biomimetic surface topography to drive rBMSCs differentiation into the osteogenic lineage. The selected surface topography in combination with the osteogenic inductive medium reveals having a synergistic effect promoting osteogenic differentiation.

Bone marrow stromal cells generate an osteoinductive microenvironment when cultured on titanium–aluminum–vanadium substrates with biomimetic multiscale surface roughness

Osseointegration of titanium-based implants possessing complex macroscale/microscale/mesoscale/nanoscale (multiscale) topographies support a direct and functional connection with native bone tissue by promoting recruitment, attachment and osteoblastic differentiation of bone marrow stromal cells (MSCs). Recent studies show that the MSCs on these surfaces produce factors, including bone morphogenetic protein 2 (BMP2) that can cause MSCs not on the surface to undergo osteoblast differentiation, suggesting they may produce an osteogenic environment in vivo. This study examined if soluble factors produced by MSCs in contact with titanium–aluminum–vanadium (Ti6Al4V) implants possessing a complex multiscale biomimetic topography are able to induce osteogenesis ectopically. Ti6Al4V disks were grit-blasted and acid-etched to create surfaces possessing macroscale and microscale roughness (MM), micro/meso/nanoscale topography (MN), and macro/micro/meso/nanoscale topography (MMNTM). Polyether-ether-ketone (PEEK) disks were also fabricated by machining to medical-grade specifications. Surface properties were assessed by scanning electron microscopy, contact angle, optical profilometry, and x-ray photoelectron spectroscopy. MSCs were cultured in growth media (GM). Proteins and local factors in their conditioned media (CM) were measured on days 4, 8, 10 and 14: osteocalcin, osteopontin, osteoprotegerin, BMP2, BMP4, and cytokines interleukins 6, 4 and 10 (IL6, IL4, and IL10). CM was collected from D14 MSCs on MMNTM and tissue culture polystyrene (TCPS) and lyophilized. Gel capsules containing active demineralized bone matrix (DBM), heat-inactivated DBM (iDBM), and iDBM + MMN-GM were implanted bilaterally in the gastrocnemius of athymic nude mice (N = 8 capsules/group). Controls included iDBM + GM; iDBM + TCPS-CM from D5 to D10 MSCs; iDBM + MMN-CM from D5 to D10; and iDBM + rhBMP2 (R&D Systems) at a concentration similar to D5–D10 production of MSCs on MMNTM surfaces. Legs were harvested at 35D. Bone formation was assessed by micro computed tomography and histomorphometry (hematoxylin and eosin staining) with the histology scored according to ASTM 2529–13. DNA was greatest on PEEK at all time points; DNA was lowest on MN at early time points, but increased with time. Cells on PEEK exhibited small changes in differentiation with reduced production of BMP2. Osteoblast differentiation was greatest on the MN and MMNTM, reflecting increased production of BMP2 and BMP4. Pro-regenerative cytokines IL4 and IL10 were increased on Ti-based surfaces; IL6 was reduced compared to PEEK. None of the media from TCPS cultures was osteoinductive. However, MMN-CM exhibited increased bone formation compared to iDBM and iDBM + rhBMP2. Furthermore, exogenous rhBMP2 alone, at the concentration found in MMN-CM collected from D5 to D10 cultures, failed to induce new bone, indicating that other factors in the CM play a critical role in that osteoinductive microenvironment. MSCs cultured on MMNTM Ti6Al4V surfaces differentiate and produce an increase in local factors, including BMP2, and the CM from these cultures can induce ectopic bone formation compared to control groups, indicating that the increased bone formation arises from the local response by MSCs to a biomimetic, multiscale surface topography.

Serial Cultivation of an MSC-Like Cell Line with Enzyme-Free Passaging Using a Microporous Titanium Scaffold.

In vitro studies on adherent cells require a process of passage to dissociate the cells from the culture substrate using enzymes or other chemical agents to maintain cellular activity. However, these proteolytic enzymes have a negative influence on the viability and phenotype of cells. The mesenchymal stem cell (MSC)-like cell line, C3H10T1/2, adhered, migrated, and proliferated to the same extent on newly designed microporous titanium (Ti) membrane and conventional culture dish, and spontaneous transfer to another substrate without enzymatic or chemical dissociation was achieved. The present study pierced a 10 μm-thick pure Ti sheet with 25 μm square holes at 75 μm intervals to create a dense porous structure with biomimetic topography. The pathway of machined holes allowed the cells to access both sides of the membrane frequently. In a culture with Ti membranes stacked above- and below-seeded cells, cell migration between the neighboring membranes was confirmed using the through-holes of the membrane and contact between the membranes as migration routes. Furthermore, the cells on each membrane migrated onto the conventional culture vessel. Therefore, a cell culture system with enzyme-free passaging was developed.

Laser-Induced µ-Rooms for Osteocytes on Implant Surface: An In Vivo Study.

Laser processing of dental implant surfaces is becoming a more widespread replacement for classical techniques due to its undeniable advantages, including control of oxide formation and structure and surface relief at the microscale. Thus, using a laser, we created several biomimetic topographies of various shapes on the surface of titanium screw-shaped implants to research their success and survival rates. A distinctive feature of the topographies is the presence of "µ-rooms", which are special spaces created by the depressions and elevations and are analogous to the µ-sized room in which the osteocyte will potentially live. We conducted the comparable in vivo study using dental implants with continuous (G-topography with µ-canals), discrete (S-topography with μ-cavities), and irregular (I-topography) laser-induced topographies. A histological analysis performed with the statistical method (with p-value less than 0.05) was conducted, which showed that G-topography had the highest BIC parameter and contained the highest number of mature osteocytes, indicating the best secondary stability and osseointegration.

Experimental analyses of surface treatment on titanium samples

The roughness of the dental implant surface will influence the behavior of osteoblastic cells regarding the spread, proliferation, differentiation and synthesis of proteins on the surface of titanium. Depending on its characteristics, roughness can be macro-, micro- and nano-roughness. Material and method. We achieved the obtaining of thin layers of biomaterials by the pulsed laser deposition method (PLD, Pulsed Laser Deposition) on the titanium samples and the deposition has been made by Spin coating method of a thin film based on hydroxyapatite, respectively hydroxyapatite-maleic copolymer, only on one side of the sample. Results. From a microscopic point of view, the qualities of bio-glass are remarkable. Thus, bio-glasses are amorphous materials and are successfully used as covering material for metallic and polymeric implants, to significantly increase their biocompatibility. Discussion. The biological properties of the materials for implants are of fundamental importance for the success of the treatments and they are reflected along with other characteristics of the implants, in the tissue reaction they cause under the conditions of their insertion in biological systems. Conclusion. Osseointegration could be impaired in people with diabetes, osteoporosis, with bone metabolism disorder where therapeutic success depends on the biomimetic and functional topography of the dental implant.

Biomimetic surface topography as a potential modulator of macrophages inflammatory response to biomaterials

The implantation of biomaterial devices can negatively impact the local microenvironment through several processes including the injury incurred during the implantation process and the associated host inflammatory response. Immune cell responses to implantable biomaterial devices mediate host-material interactions. Indeed, the immune system plays a central role in several biological processes required for the integration of biomaterials such as wound healing, tissue integration, inflammation, and foreign body reactions. The implant physicochemical properties such as size, shape, surface area, topography, and chemistry have been shown to provide cues to the immune system. Its induced immune-modulatory responses towards inflammatory or wound healing phenotypes can determine the success of the implant.In this work, we aim to evaluate the impact of some biomimetic surface topographies on macrophages' acute inflammatory response. For that, we selected 4 different biological surfaces to replicate through soft lithography on spin casting PCL membranes. Those topographies were: the surface of E. coli, S.eppidermidis and L929 cells cultured in polystyrene tissue culture disks, and an Eggshell membrane. We selected a model based on THP-1-derived macrophages to study the analysis of the expression of both pro-inflammatory and anti-inflammatory markers. Our results revealed that depending on the surface where these cells are seeded, they present different phenotypes. Macrophages present a M1-like phenotype when they are cultured on top of PCL membranes with the surface topography of E. coli and S. epidermidis. When cultured on membranes with L929 monolayers or Eggshell membrane surface topography, the macrophages present a M2-like phenotype. These results can be a significant advance in the development of new implantable biomaterial devices since they can help to modulate the inflammatory responses to implanted biomaterials by controlling their surface topography.

Tailoring of TiAl6V4 Surface Nanostructure for Enhanced In Vitro Osteoblast Response via Gas/Solid (Non-Line-of-Sight) Oxidation/Reduction Reactions.

An aging global population is accelerating the need for better, longer-lasting orthopaedic and dental implants. Additive manufacturing can provide patient-specific, titanium-alloy-based implants with tailored, three-dimensional, bone-like architecture. Studies using two-dimensional substrates have demonstrated that osteoblastic differentiation of bone marrow stromal cells (MSCs) is enhanced on surfaces possessing hierarchical macro/micro/nano-scale roughness that mimics the topography of osteoclast resorption pits on the bone surface. Conventional machined implants with these surfaces exhibit successful osseointegration, but the complex architectures produced by 3D printing make consistent nanoscale surface texturing difficult to achieve, and current line-of-sight methods used to roughen titanium alloy surfaces cannot reach all internal surfaces. Here, we demonstrate a new, non-line-of-sight, gas/solid-reaction-based process capable of generating well-controlled nanotopographies on all open (gas-exposed) surfaces of titanium alloy implants. Dense 3D-printed titanium-aluminum-vanadium (TiAl6V4) substrates were used to evaluate the evolution of surface nanostructure for development of this process. Substrates were either polished to be smooth (for easier evaluation of surface nanostructure evolution) or grit-blasted and acid-etched to present a microrough biomimetic topography. An ultrathin (90 ± 16 nm) conformal, titania-based surface layer was first formed by thermal oxidation (600 °C, 6 h, air). A calciothermic reduction (CaR) reaction (700 °C, 1 h) was then used to convert the surface titania (TiO2) into thin layers of calcia (CaO, 77 ± 16 nm) and titanium (Ti, 51 ± 20 nm). Selective dissolution of the CaO layer (3 M acetic acid, 40 min) then yielded a thin nanoporous/nanorough Ti-based surface layer. The changes in surface nanostructure/chemistry after each step were confirmed by scanning and transmission electron microscopies with energy-dispersive X-ray analysis, X-ray diffraction, selected area electron diffraction, atomic force microscopy, and mass change analyses. In vitro studies indicated that human MSCs on CaR-modified microrough surfaces exhibited increased protein expression associated with osteoblast differentiation and promoted osteogenesis compared to unmodified microrough surfaces (increases of 387% in osteopontin, 210% in osteocalcin, 282% in bone morphogenic protein 2, 150% in bone morphogenic protein 4, 265% in osteoprotegerin, and 191% in vascular endothelial growth factor). This work suggests that this CaR-based technique can provide biomimetic topography on all biologically facing surfaces of complex, porous, additively manufactured TiAl6V4 implants.

Biomimetic Surface Topography from the Rubus fruticosus Leaf as a Guidance of Angiogenesis in Tissue Engineering Applications.

The promotion of angiogenesis is a fundamental step for efficient organ/tissue reconstitution and replacement. Thus, several strategies to promote vascularization of scaffolds were studied to satisfy this unsolved clinical need. The interface between cells and substrates is a determinant for the success of tissue engineering (TE) strategies. Substrate's topography is reported to play a key role in influencing endothelial cell behavior, namely, on its proliferation, metabolic activity, morphology, migration, and secretion of cytokines and chemokines. Therefore, surface topography of the biomaterial-based grafts is a crucial property that is considered in the development of a new TE approach. Herein, we hypothesize that the surface of Rubus fruticosus leaf plays a crucial role in driving angiogenesis since its architecture resembles the vascular structures at a biologically relevant size scale. For this, we produced biomimetic polycaprolactone (PCL) membranes (BpMs) replicating the surface topography of a R. fruticosus leaf by replica molding and nanoimprint lithography. Our results showed an enhanced performance in terms of proliferation of the human endothelial cell line on top of the BpM. Moreover, an asymmetric cellular spatial distribution among the surface of the BpM was observed. These cells seem to have higher density for longer time periods in the region that replicates the leaf veins. Finally, we assess the angiogenic capacity through a chick chorioallantoic membrane assay, revealing that BpMs are more prone to support angiogenesis than flat PCL membranes. We strongly believe that this strategy can bring new insights into developing TE strategies with an enhanced performance in terms of the vascular integration between the host and the scaffolds implanted.

A Review of Biomimetic Topographies and Their Role in Promoting Bone Formation and Osseointegration: Implications for Clinical Use.

The use of metallic and polymeric materials for implants has been increasing over the past decade. This trend can be attributed to a variety of factors including a significant increase in basic science research focused on implant material characteristics and how various surface modifications may stimulate osseointegration and, ultimately, fusion. There are many interbody fusion devices and dental implants commercially available; however, detailed information about their surface properties, and the effects that various materials and surface modifications may have on osteogenesis, is lacking in the literature. While the concept of bone-implant osseointegration is a relatively recent addition to the spine fusion literature, there is a comparatively large body of literature related to dental implants. The purpose of this article is to summarize the science of surface modified bone-facing implants, focusing on biomimetic material chemistry and topography of titanium implants, to promote a better understanding of how these characteristics may impact bone formation and osseointegration. This manuscript has the following aspects: highlights the role of titanium and its alloys as potent osteoconductive bioactive materials; explores the importance of biomimetic surface topography at the macro-, micro- and nano-scale; summarizes how material surface design can influence osteogenesis and immune responses in vitro; focuses on the kinds of surface modifications that play a role in the process. Biomimetic surface modifications can be varied across many clinically available biomaterials, and the literature supports the hypothesis that those biomaterial surfaces that exhibit physical properties of bone resorption pits, such as roughness and complex hierarchical structures at the submicron and nanoscale, are more effective in supporting osteoblast differentiation in vitro and osteogenesis in vivo.

A Study to Compare the Fouling Resistance and Self-cleaning Properties of Two-patterned Surfaces with an Un-patterned Control Surface

Biofouling is an unwelcomed phenomenon where unwanted biological matter adheres to surfaces with the presence of water, resulting in alteration to the properties of the surface. This affects many industries, especially the marine industry. Multiple biofouling control studies have been conducted to minimize damage and maintenance cost of these surfaces. With rising concerns on the toxicity of current control methods towards the environment, non-toxic methods shown to be effective are surface modifications such as self-cleaning or biomimetic textured surfaces. One of the biomimetic surfaces, shark’s skin has shown anti-fouling properties due to its surface riblets with low drag properties based on studies done. However, few researches are conducted to implement these biomimetic surface topographies for real anti-fouling applications. Therefore, this project explores the possibilities in implementing biomimetic surface topographies such as shark’s skin in real life applications using computational fluid dynamics (CFD) analysis and also to manufacture these surfaces using 3D printing methods. A computer-aided design (CAD) model of shark skin and un-patterned surface topographies are used to study the behavior of fluid over these surfaces in CFD fluent in ANSYS software. The hydrodynamic variable data such as wall shear stress over the surface topography is represented in a contour and vector plot, these results are then analyzed. According to the hypotheses, the biomimetic shark skin surface topography will show higher wall shear stress, indicating anti-fouling properties. In the next part of this project is the manufacturing of these surface, the goal is to provide a cheaper alternative to current micro-structured surface production methods such as photolithography. Additive manufacturing such as fused deposition modeling (FDM) 3D printing can potentially provide a manufacturing method with a much lower cost and time needed. Thus, 3D printing of the biomimetic shark skin surface topography will be carried out in this project to determine if FDM can provide a manufacturing solution to anti-fouling micro-topography surfaces.

Material advancement in tissue-engineered nerve conduit

Abstract Peripheral nerve injuries resulting from various traumatic events can cause mobility problems and sensory impairment, jeopardizing patients’ life quality and bringing serious economic burdens. Due to the shortcomings of autologous nerve grafts, such as limited tissue sources, unmatched size, and loss of innervation at the donor site, tissue-engineered nerve grafts using both natural and synthetic materials have been employed in the treatment of peripheral nerve defect and to promote nerve regeneration. Apart from traditional advantages such as good biocompatibility and controllable degradation, the development of fabrication technology and the advancement in material science have endowed tissue-engineered nerve conduits with upgraded properties such as biomimetic surface topography, extracellular matrix components, neurotrophic factors, and cell seeding, or a conduit with micropores on the surface for substance exchange and/or with fillers inside for microenvironment simulation. This article reviews recent progress in the biomaterials employed in fabricating tissue-engineered nerve conduits, in vitro characterization, and their applications in nerve repair in animal studies as well as in clinical trials.

Biomimetic electrospun tubular PLLA/gelatin nanofiber scaffold promoting regeneration of sciatic nerve transection in SD rat

The micro- or nanoscale surface morphology of the tissue engineering nerve guidance scaffold (NGS) will affect different cell behaviors, such as their growth rate, migration, and matrix secretion. Although different technologies for manufacturing scaffolds with biomimetic topography have been established, most of them tend to be high cost and long preparation time. Here we have prepared a biomimetic NGS with physical properties to simulate native nerve tissue more accurately. We used poly(l-lactic acid) (PLLA) nanofibers doped with gelatin to prepare a biomimetic NGS whose structure mimics the native epineurium layer. By adjusting the doping ratio of gelatin and PLLA in the tubular scaffold, the bionic scaffold's surface morphology and mechanical properties are closer to native tissues. In vitro cell scaffold interaction experiments demonstrated that the PLLA/gelatin nanofibers could significantly promote the elongation, proliferation, and the secretion of glial cell-derived neurotrophic factor (GDNF) of RSC96 Schwann cells (SCs), as well as the diffusion of GDNF. In vivo scaffold replacement of SD rat, sciatic nerves showed that the nerve guide scaffold composed of PLLA/gelatin nanofibers was helpful to the myelination of SCs and the remolding of epineurium in the injured area, which could effectively rehabilitate the motor and sensory functions of the injured nerve and prevent the atrophy of the target muscle tissue. This study showed that the synergistic impact of nano topographical and biochemical clues on designing biomimetic scaffolds could efficiently promote regenerating nerve tissue.

Tendon-Derived Biomimetic Surface Topographies Induce Phenotypic Maintenance of Tenocytes In Vitro

The tenocyte niche contains biochemical and biophysical signals that are needed for tendon homeostasis. The tenocyte phenotype is correlated with cell shape in vivo and in vitro, and shape-modifying cues are needed for tenocyte phenotypical maintenance. Indeed, cell shape changes from elongated to spread when cultured on a flat surface, and rat tenocytes lose the expression of phenotypical markers throughout five passages. We hypothesized that tendon gene expression can be preserved by culturing cells in the native tendon shape. To this end, we reproduced the tendon topographical landscape into tissue culture polystyrene, using imprinting technology. We confirmed that the imprints forced the cells into a more elongated shape, which correlated with the level of Scleraxis expression. When we cultured the tenocytes for 7 days on flat surfaces and tendon imprints, we observed a decline in tenogenic marker expression on flat but not on imprints. This research demonstrates that native tendon topography is an important factor contributing to the tenocyte phenotype. Tendon imprints therefore provide a powerful platform to explore the effect of instructive cues originating from native tendon topography on guiding cell shape, phenotype, and function of tendon-related cells.

Corneal endothelium tissue engineering: An evolution of signaling molecules, cells, and scaffolds toward 3D bioprinting and cell sheets.

Cornea is an avascular and transparent tissue that focuses light on retina. Cornea is supported by the corneal-endothelial layer through regulation of hydration homeostasis. Restoring vision in patients afflicted with corneal endothelium dysfunction-mediated blindness most often requires corneal transplantation (CT), which faces considerable constrictions due to donor limitations. An emerging alternative to CT is corneal endothelium tissue engineering (CETE), which involves utilizing scaffold-based methods and scaffold-free strategies. The innovative scaffold-free method is cell sheet engineering, which typically generates cell layers surrounded by an intact extracellular matrix, exhibiting tunable release from the stimuli-responsive surface. In some studies, scaffold-based or scaffold-free technologies have been reported to achieve promising outcomes. However, yet some issues exist in translating CETE from bench to clinical practice. In this review, we compare different corneal endothelium regeneration methods and elaborate on the application of multiple cell types (stem cells, corneal endothelial cells, and endothelial precursors), signaling molecules (growth factors, cytokines, chemical compounds, and small RNAs), and natural and synthetic scaffolds for CETE. Furthermore, we discuss the importance of three-dimensional bioprinting strategies and simulation of Descemet's membrane by biomimetic topography. Finally, we dissected the recent advances, applications, and prospects of cell sheet engineering for CETE.

Infarct Collagen Topography Regulates Fibroblast Fate via p38-Yes-Associated Protein Transcriptional Enhanced Associate Domain Signals.

Myocardial infarction causes spatial variation in collagen organization and phenotypic diversity in fibroblasts, which regulate the heart's ECM (extracellular matrix). The relationship between collagen structure and fibroblast phenotype is poorly understood but could provide insights regarding the mechanistic basis for myofibroblast heterogeneity in the injured heart. To investigate the role of collagen organization in cardiac fibroblast fate determination. Biomimetic topographies were nanofabricated to recapitulate differential collagen organization in the infarcted mouse heart. Here, adult cardiac fibroblasts were freshly isolated and cultured on ECM topographical mimetics for 72 hours. Aligned mimetics caused cardiac fibroblasts to elongate while randomly organized topographies induced circular morphology similar to the disparate myofibroblast morphologies measured in vivo. Alignment cues also induced myofibroblast differentiation, as >60% of fibroblasts formed αSMA (α-smooth muscle actin) stress fibers and expressed myofibroblast-specific ECM genes like Postn (periostin). By contrast, random organization caused 38% of cardiac fibroblasts to express αSMA albeit with downregulated myofibroblast-specific ECM genes. Coupling topographical cues with the profibrotic agonist, TGFβ (transforming growth factor beta), additively upregulated myofibroblast-specific ECM genes independent of topography, but only fibroblasts on flat and randomly oriented mimetics had increased percentages of fibroblasts with αSMA stress fibers. Increased tension sensation at focal adhesions induced myofibroblast differentiation on aligned mimetics. These signals were transduced by p38-YAP (yes-associated protein)-TEAD (transcriptional enhanced associate domain) interactions, in which both p38 and YAP-TEAD (yes-associated protein transcriptional enhanced associate domain) binding were required for myofibroblast differentiation. By contrast, randomly oriented mimetics did not change focal adhesion tension sensation or enrich for p38-YAP-TEAD interactions, which explains the topography-dependent diversity in fibroblast phenotypes observed here. Spatial variations in collagen organization regulate cardiac fibroblast phenotype through mechanical activation of p38-YAP-TEAD signaling, which likely contribute to myofibroblast heterogeneity in the infarcted myocardium.