Biopotential Electrodes Research Articles

Evaluating Major Electrode Types for Idle Biological Signal Measurements for Modern Medical Technology.

Biological signals such as electrocardiogram (ECG) and electromyography (EMG) that can be measured at home can reveal vital information about the patient’s health. In today modern technology, the measured ECG or EMG signals at home can be monitored by medical staff from long distance through the use of internet. Biopotential electrodes are crucial in monitoring ECG, EMG, etc., signals. Applying the right type of electrode that lasts for a long time and assists in recording high signal quality is desirable in medical devices industry. Three types of electrodes (Silver/Silver Chloride (Ag/AgCl) electrodes, Orbital electrodes and Stainless steel electrodes) were tested to identify the most appropriate one for recording biological signals. The evaluation was based on determining the electrode circuit model components and having high capacitance value or high capacitor value of electrode circuit model (Cd) and low electrode-skin impedance value or low resistor value of electrode circuit model (Rd). The results revealed that Ag/AgCl is the best type of electrodes, followed by Orbital electrodes. Stainless steel electrodes had performed poorly. However, Orbital electrodes material can last longer than Ag/AgCl and hence perform similar to Ag/AgCl electrodes, which can be idle for monitoring biological signals at home without the need for medical staff to replace the electrodes in a short period of time.

Visualization of electrical field of electrode using voltage-controlled fluorescence release

In this study we propose an approach to directly visualize electrical current distribution at the electrode–electrolyte interface of a biopotential electrode. High-speed fluorescent microscopic images are acquired when an electric potential is applied across the interface to trigger the release of fluorescent material from the surface of the electrode. These images are analyzed computationally to obtain the distribution of the electric field from the fluorescent intensity of each pixel. Our approach allows direct observation of microscopic electrical current distribution around the electrode. Experiments are conducted to validate the feasibility of the fluorescent imaging method.

Electrochemical characterization of nanostructured Ag:TiN thin films produced by glancing angle deposition on polyurethane substrates for bio-electrode applications

Flexible polyurethane substrates were coated with Ag:TiN thin films (N/Ti atomic ratio=0.7; 10at.% Ag), with different column inclinations (α=0°, 40° and 80°) and architectures (columnar, zigzag with 2 and 4 periods), using the Glancing Angle Deposition (GLAD) technique. The coatings were characterized in order to assess the best thin film architecture to suit the bio-potential electrode applications. An abrupt increase of porosity of the samples was perceivable with increasing α angles (particularly from 40° to 80°). Hence, the sputtered films could be divided into dense (Ag:TiN 0° and Ag:TiN 40°) and porous (Ag:TiN 80°, Ag:TiN 80° 2Z and Ag:TiN 80° 4Z) samples. The electrochemical behaviour of the samples was consistently linked to the porosity differences, which was accompanied by an increase of the surface Ag content. Furthermore, the porous samples exhibited lower impedances (~104Ωcm2 at 2MHz), as well as electrochemical noise and drift rate values similar to those of the commercial Ag/AgCl electrodes. Hence, the porous Ag:TiN 80°, Ag:TiN 80° 2Z and Ag:TiN 80° 4Z porous Ag:TiN GLAD coatings seem to be the most promising architectures for the envisaged bio-potential electrode applications.

Ag:TiN‐Coated Polyurethane for Dry Biopotential Electrodes: From Polymer Plasma Interface Activation to the First EEG Measurements

Several plasma treatments using argon, oxygen, and nitrogen are studied in order to increase the interfacial adhesion of the polyurethane/Ag:TiN system to be used as biopotential electrodes. The optimized plasma treatments conditions (100 W, 15 min, regardless of the gas) promote a steep decrease of the water contact angle values. The observed chemical and topographic alterations translate into excellent polyurethane/Ag:TiN interfacial adhesion of the plasma treated samples. The in‐service validation of the proposed Ag:TiN‐coated PU multipin electrodes is performed by acquiring EEG signals in parallel with the standard wet Ag/AgCl electrodes. No considerable differences are found in terms of shape, amplitude, and spectral characteristics of the signals when comparing reference wet and dry electrodes.

Ag y :TiN x thin films for dry biopotential electrodes: the effect of composition and structural changes on the electrical and mechanical behaviours

In the present work, Ag y :TiN x thin films, obtained by reactive DC magnetron sputtering, with decreasing [N]/[Ti] atomic ratios (from 1 to 0.1) and a fixed amount of Ag pellets placed in the erosion zone of a pure Ti target, were studied envisaging their application as biopotential electrodes. The strongly under-stoichiometric samples, [N]/[Ti] = 0.1 and 10 at.% Ag; [N]/[Ti] = 0.2 and 8 at.% Ag, were found to be composed of a N-doped hcp-Ti structure, with possible formation of TiAg or Ti2Ag intermetallics. These samples exhibit high electrical resistivity values and low hardness and reduced modulus. In the set of samples indexed to a transition zone, [N]/[Ti] = 0.3 and 15 at.% Ag; [N]/[Ti] = 0.7 and 32 at.% Ag, a hcp-Ti to fcc-TiN phase transformation took place, giving rise to a disaggregated N-deficient TiN matrix. It correlates with the high resistivity values as well as the higher hardness and reduced modulus values that were obtained. The last identified zone comprised the stoichiometric Ag:TiN x sample—[N]/[Ti] = 1 and 20 at.% Ag. Extensive metallic Ag segregation was detected, contributing to a significant decrease of the resistivity and hardness values.

A motion artifact generation and assessment system for the rapid testing of surface biopotential electrodes

Dry electrodes can reduce cost while increasing the usability and comfort of wearable monitoring systems. They are, however, susceptible to motion artifacts. The present electrode testing methods lack reliability and do not separate the factors that affect the motion artifact. In this paper, we introduce a first generation motion artifact generation and assessment system that generates the speed, amplitude, and pattern-wise programmable movement of the electrode. The system simultaneously measures electrode–skin impedance, the motion artifact, and one channel of an electrocardiogram that contains the motion artifact and monitors the mounting force applied to the electrode. We demonstrate the system by comparing the applied movement and the measured signals for electrode movements up to 6 mm and movement frequencies from 0.4 Hz to 4 Hz. Results show that the impedance change and surface potential are visually clearly related to the applied motion, with average correlations of 0.89 and 0.64, respectively. The applied force, electrode location, and electrode structure all affect the motion artifact. The setup enables the motion of the electrode to be accurately controlled. The system can be used as a precursor to the testing of integrated systems because it enables thorough, repeatable, and robust motion artifact studies. The system allows a deeper insight into motion artifacts and the interplay of the various factors that affect them.

Conductive rubber electrodes for earphone-based eye gesture input interface

An eartip made of conductive rubber that also realizes biopotential electrodes is proposed for a daily-use earphone-based eye gesture input interface. Several prototypes, each with three electrodes...

Wireless impedance measurements for monitoring peripheral vascular disease.

Wireless microdevices powered by ultrasound energy have been fabricated to measure and telemeter tissue impedance spectrums for applications in peripheral vascular disease monitoring. The system is characterized by simplicity of the implant consisting of only two electrical components. Ex vivo testing shows the potential for constructing tissue impedance spectrum plots over the range from 10 Hz to 10 kHz by a device less than 1 mm in diameter and 1 cm long. The neurostimulator microdevice was powered by continuous waveform 650 kHz ultrasound with a swept-frequency amplitude modulation. The system was operated at safe ultrasound power levels on the order of 10-100 mW/cm(2). The device proved to be sensitive and able to measure tissue impedances over a broad range. Volume conducted signals carrying impedance information from the microdevice were remotely detected by surface biopotential electrodes.

Microscopic imaging of electrical current distribution at the electrode-electrolyte interface.

A method to directly visualize electrical current distribution at the electrode-electrolyte interface of a biopotential electrode is presented in this paper. A voltage-responsive florescent material is first coated on the surface of a bioelectrode. Then, an electric potential is used to activate the release of the florescent material while a camera acquires images at the electrode-electrolyte interface. This imaging method allows observation of microscopic electrical current distribution at the active area of the electrode, providing a new tool to optimize bioelectrode design. Our computational and experimental data demonstrate the feasibility of the florescent imaging method.

Triboelectrification based motion sensor for human-machine interfacing.

We present triboelectrification based, flexible, reusable, and skin-friendly dry biopotential electrode arrays as motion sensors for tracking muscle motion and human-machine interfacing (HMI). The independently addressable, self-powered sensor arrays have been utilized to record the electric output signals as a mapping figure to accurately identify the degrees of freedom as well as directions and magnitude of muscle motions. A fast Fourier transform (FFT) technique was employed to analyse the frequency spectra of the obtained electric signals and thus to determine the motion angular velocities. Moreover, the motion sensor arrays produced a short-circuit current density up to 10.71 mA/m(2), and an open-circuit voltage as high as 42.6 V with a remarkable signal-to-noise ratio up to 1000, which enables the devices as sensors to accurately record and transform the motions of the human joints, such as elbow, knee, heel, and even fingers, and thus renders it a superior and unique invention in the field of HMI.

Impedance spectroscopy of changes in skin-electrode impedance induced by motion.

BackgroundThe motion artifact is an ever-present challenge in the mobile monitoring of surface potentials. Skin-electrode impedance is investigated as an input parameter to detect the motion artifact and to reduce it using various methods. However, the impact of the used impedance measurement frequency on the relationship between measured impedance and the motion artifact and the relationship between the impedance and the motion is not well understood.MethodsIn this paper, for the first time, we present the simultaneous measurement of impedance at 8 current frequencies during the application of controlled motion to the electrode at monitored electrode mounting force. Three interwoven frequency groupings are used to obtain a spectrum of 24 frequencies between 25 Hz and 1 MHz for ten volunteers. Consequently, the surface potential and one channel of ECG are measured from the electrode subject to controlled motion. The signals are then analyzed in time and frequency domain.ResultsThe results show that the different frequencies of impedance measurements do not reflect the motion in the same manner. The best correlation between impedance and the applied motion was seen at impedance current frequencies above 17 kHz. For resistance this relationship existed for frequencies above 11 kHz, Reactance did not show good time domain correlation, but had good frequency domain correlation at frequencies higher than 42 kHz. Overall, we found that the impedance signal correlated well with the applied motion; however impedance had lower correlation to actual motion artifact signal.ConclusionBased on our results, we can conclude that the current frequency used for the impedance measurement has a great effect on the relationship of the measurement to the applied motion and its relationship with the resulting motion artifact. Therefore, when flat textile contact biopotential electrodes are used, frequencies higher than 17 kHz are best suited for impedance measurements intended for the estimation of electrode motion or motion artifact. For resistance, the best frequencies to use are higher than 11 kHz.

Towards true unipolar ECG recording without the Wilson central terminal (preliminary results)

We present an innovative bio-potential front-end capable of recording true unipolar ECG leads for the first time without making use of the Wilson central terminal. In addition to the convenience in applications such as continuous monitoring and rapid diagnosis, the information in unipolar recordings may yield unique diagnostic information as it avoids the need to essentially subtract data or make use of the averaging effect imposed from the Wilson central terminal. The system also allows direct, real-time software calculation of signals corresponding to standard ECG leads which achieve correlations in excess of 92% with a gold standard ECG during a parallel in vivo recording. In addition, the implemented circuit is wideband (0.05–1000 Hz), compatible with standard (Ag/AgCl) bio-potential electrodes, and dry (paste-less) textile electrodes. The circuit is also low power, requiring less than 50 mW (when powered at 12 V) per standard ECG lead (two channels required). It is therefore well suited for wearable, long-term applications.

전도성 에폭시를 이용한 직물 위에 구현된 건식 생체전위 전극의 연구

In this paper, micro dried bio-potential electrodes are demonstrated for sEMG (surface ElectroMyoGraphic) signal measurement using conductive epoxy on the textile fabric. Micro dried bio-potential electrodes on the textile fabric substrate have several advantages over the conventional wet/dry electrodes such as good feeling of wearing, possibility of extended-wearing due to the good ventilation. Also these electrodes on the textile fabric can easily apply to the curved skin surface. These electrodes are fabricated by the screen-printing process with the size of and the resultant resistance of these electrodes have the average value of . The conventional silver chloride electrode shows the average value of . However, the electrode on the textile fabric are able to measure the sEMG signal without feeling of difference and this electrode shows the lower resistance of than conventional silver chloride electrode with in the condition of the very sharp curve surface (the radius of curvature is 40 mm).

A Low-Power Bio-Potential Acquisition System with Flexible PDMS Dry Electrodes for Portable Ubiquitous Healthcare Applications

This work describes a bio-potential acquisition system for portable ubiquitous healthcare applications using flexible polydimethylsiloxane dry electrodes (FPDEs) and a low-power recording circuit. This novel FPDE used Au as the skin contact layer, which was made using a CO2 laser and replica method technology. The FPDE was revised from a commercial bio-potential electrode with a conductive snap using dry electrodes rather than wet electrodes that proposed reliable and robust attachment for the purpose of measurement, and attaching velcro made it wearable on the forearm for bio-potential applications. Furthermore, this study proposes a recording device to store bio-potential signal data and provides portability and low-power consumption for the proposed acquisition system. To acquire differential bio-potentials, such as electrocardiogram (ECG) signals, the proposed recording device includes a low-power front-end acquisition chip fabricated using a complementary metal-oxide-semiconductor (CMOS) process, a commercial microcontroller (MSP430F149), and a secure digital (SD) card for portable healthcare applications. The proposed system can obtain ECG signals efficiently and are comfortable to the skin. The power consumption of the system is about 85 mW for continuous working over a 3 day period with two AA batteries. It can also be used as a compact Holter ECG system.

A dynamic measurement system for evaluating dry bio-potential surface electrodes

In this paper, a dynamic measurement system (DMS) is presented for assessing performance of wearable and dry bio-potential surface electrodes (DBSEs) in air, especially motion artifacts. A pair of perforated membranes is assembled on the two ends of the barrel which contains electrolyte to simulate surface of the skin. The pressure of electrode/membrane can be controlled and measured, one of electrodes can move on membrane by the motion controller. Experimental results show maximum coefficient of variation (CV) of electrical impedance spectra (EIS) and dynamic open circuit potential variation (DOCP, so-called motion artifacts) of gold electrode pair are, respectively, 4.3% and 7.2% in continuous measurements, 12.6% and 22% in discontinuous measurements, the pressure and the length of motion track between electrode and membrane are strongly linear correlation with DOCP variations. EIS and DOCP of five types of electrodes were measured on DMS and their parameters of equivalent circuit (EC) of EIS and DOCP variation show larger is equivalent capacitance in electrode/electrolyte interface, less is DOCP variation. DOCP variations of two batches of electrode performed respectively on DMS and on skin have approximate 0.64 of Pearson correlation coefficient. In general, the DMS provides a powerful tool to investigate the mechanism of DOCP variation and evaluates the static or dynamic performance of electrodes. However, parameters of EC model by fitting EIS can predict the motion artifact and help the design of electrode and its integrated wearable garments.

Performance Evaluation of Surface Biopotential Dry Electrodes based on PSD and EIS

Performance Evaluation of Surface Biopotential Dry Electrodes based on PSD and EIS

A MEMS-based pyramid micro-needle electrode for long-term EEG measurement

The microelectromechanical systems process including cutting, isotropic wet-etching and sputtering was used to fabricate a pyramid micro-needle electrode, which could be applied in long-term electroencephalogram (EEG) measurement. A penetrating testing and comfort survey was presented to optimize the parameters of applying force and penetrating depth in order to make user comfort, safe and free of pain and bleeding. To investigate the performance of the micro-needle electrode, three micro-needle electrodes with different arrays were deployed to perform skin–electrode contact impedance experiments. Moreover, the impedances in time domain were measured to verify the feasibility of long time measurement. At last, EEG signals were recorded directly by three pairs of standard wet/micro-needle electrodes and the power spectrum density (PSD) was presented between standard wet electrode and micro-needle electrode to estimate signal quality. Based on the results of EEG signals and the PSD, the micro-needle electrode can be as a biopotential electrode for recording EEG with low skin–electrode contact impedance.

Micromachined three-dimensional electrode arrays for transcutaneous nerve tracking

We report the development of metal transfer micromolded (MTM) three-dimensional microelectrode arrays (3D MEAs) for a transcutaneous nerve tracking application. The measurements of electrode–skin–electrode impedance (ESEI), electromyography (EMG) and nerve conduction utilizing these minimally invasive 3D MEAs are demonstrated in this paper. The 3D MEAs used in these measurements consist of a metalized micro-tower array that can penetrate the outer layers of the skin in a painless fashion and are fabricated using MTM technology. Two techniques, an inclined UV lithography approach and a double-side exposure of thick negative tone resist, have been developed to fabricate the 3D MEA master structure. The MEAs themselves are fabricated from the master structure utilizing micromolding techniques. Metal patterns are transferred during the micromolding process, thereby ensuring reduced process steps compared to traditional silicon-based approaches. These 3D MEAs have been packaged utilizing biocompatible Kapton® substrates. ESEI measurements have been carried out on test human subjects with standard commercial wet electrodes as a reference. The 3D MEAs demonstrate an order of magnitude lower ESEI (normalized to area) compared to wet electrodes for an area that is 12.56 times smaller. This compares well with other demonstrated approaches in literature. For a nerve tracking demonstration, we have chosen EMG and nerve conduction measurements on test human subjects. The 3D MEAs show 100% improvement in signal power and SNR/√area as compared to standard electrodes. They also demonstrate larger amplitude signals and faster rise times during nerve conduction measurements. We believe that this microfabrication and packaging approach scales well to large-area, high-density arrays required for applications like nerve tracking. This development will increase the stimulation and recording fidelity of skin surface electrodes, while increasing their spatial resolution by an order of magnitude or more. Although biopotential electrode systems are not without their challenges, the non-invasive access to neural information, along with the potential for automation with associated electronic and software development, is precisely what makes this technology an excellent candidate for the next generation in diagnostic, therapeutic, and prosthetic devices.

Classification of Bio-potential Surface Electrode based on FKCM and SVM

In this paper, a method which is used for evaluating the performance of bio-potential surface electrode (BSE) with multi-index is presented. The Fuzzy kernel C-means (FKCM) algorithm and KF statistic are employed for classifying the BSE samples and searching an optimal classification amount respectively. Subsequently, a discriminant function is constructed by support vector machines (SVM) for recognizing the new measured samples. Experimental result shows classification correction ratios of improved FKCM algorithm are 96.3% and 85% on the IRIS and BSE dataset according a priori knowledge, furthermore, the recognition correction ratios of SVM algorithm are 96.3% and 90% on the IRIS and BSE dataset. Index Terms—FKCM, SVM, classification, recognition, bio- potential surface electrode

Wireless Point-of-Care Diagnosis for Sleep Disorder With Dry Nanowire Electrodes

Currently, available sleep monitoring systems use electrical recording where the electrodes make contact with the patient’s skin using a conducting gel. The electrode wires are connected to a processing recording system. The subject has to be in close proximity of these machines due to the direct electrical connections with the body and the machine. The conductive gel along with many wires connected to the biopotential electrodes makes them uncomfortable for the subject, with the result that recording and monitoring of the patient’s sleep patterns can become very difficult. The patient has to be in a sleep lab and/or a hospital at all times and at least one technician needs to watch the patient’s sleep behavior via video. The patient may not experience normal sleep patterns under such environments and as such, the diagnostic results are not really very conclusive. The commonly monitored biopotential electrodes are electrocardiogram, electroencephalogram, electromyogram, and electrooculogram. The electrodes used for monitoring these signals are Ag/AgCl and gold, which require skin preparation by means of scrubbing to remove the dead cells and application of electrolytic gel to reduce the skin contact resistance. The gel takes a role of reducing skin contact impedance in the conventional Ag/AgCl electrode and its usage is directly related to the sensitivity. However, the wet conventional Ag/AgCl electrode has some drawbacks such as difficulty in long time monitoring because the gel dries out after few hours and skin irritations. Usually, physiological parameters are monitored over an extended period of time during the patient’s normal daily life to diagnose a disease. In this case, the wet conventional Ag/AgCl cannot be used because of the dry-out of gel. The dry-out of gel increases the impedance between skin and electrode and it is reflected in the poor signal sensitivity. Also noises, such as motion artifact and baseline wander, are added to the biopotential signals as the electrode floats over the electrolytic gel during monitoring. To overcome these drawbacks, dry nanoelectrodes are proposed in this paper where the electrodes are held against the skin surface to establish contact with the skin without the need for electrolytic fluids or gels. The results are presented along with a wireless communication such that the proposed system is ideal for point-of-care diagnosis of the patient at home.