Backing Material Research Articles

A one-stop integrated natural antimicrobial microneedles with anti-inflammatory, pro-angiogenic and long-term moisturizing properties to accelerate diabetic wound healing

Diabetic ulcers present a formidable obstacle in diabetes management, typically leading to high mortality and amputation rates. To overcome traditional monotherapy drawbacks, We developed a novel microneedle strategy for combined antimicrobial action: ingeniously integrating quercetin with Platelet-derived Growth Factor-BB(PDGF-BB) and Sucrose Octasulfate(SOS) into the microneedle system(QPS MN). This method allows to penetrate through biofilms, administering quercetin nanocrystals and PDGF-BB deep into the tissue to combat microbial infection, mitigate inflammation, and promote angiogenesis. The accompanying backing material contains SOS, which absorbs wound exudate and forms a dressing that provides a moist environment for wound healing In an in vitro wound-scratch assay demonstrated that co-cultivating Human Umbilical Vein Endothelial Cells(HUVEC) with QPS MN for 48 h (90.3 ± 2.51 %) significantly enhanced cell migration compared to the control group (20.2 ± 1.41 %). Moreover, treatment of streptozotocin-induced diabetic wounds in rats with QPS MN for 14 days resulted in a wound healing rate of 96.56 ± 3.44 %, far surpassing the healing rate of only 40.34 ± 7.26 % observed in the untreated control group. Furthermore, the QPS MN treated wounds exhibited a notable increase in skin appendages and neovascularisation, indicating promising potential for achieving complete wound healing. These results suggest that QPS MN may offer substantial therapeutic benefits for addressing diabetic wounds.

A Cost-Effective Approach to Creating Large Silicone Rubber Molds Using Advanced Rigid Polyurethane Foam.

In practical applications, polyurethane (PU) foam must be rigid to meet the demands of various industries and provide comfort and protection in everyday life. PU foam components are extensively used in structural foam, thermal insulation, decorative panels, packaging, imitation wood, and floral foam, as well as in models and prototypes. Conventional technology for producing PU foam parts often leads to defects such as deformation, short shots, entrapped air, warpage, flash, micro-bubbles, weld lines, and voids. Therefore, the development of rigid PU foam parts has become a crucial research focus in the industry. This study proposes an innovative manufacturing process for producing rigid PU foam parts using silicone rubber molds (SRMs). The deformation of the silicone rubber mold can be predicted based on its wall thickness, following a trend equation with a correlation coefficient of 0.9951. The volume of the PU foam part can also be predicted by the weight of the PU foaming agent, as indicated by a trend equation with a correlation coefficient of 0.9824. The optimal weight ratio of the foaming agent to water, yielding the highest surface hardness, was found to be 5:1. The surface hardness of the PU foam part can also be predicted based on the weight of the water used, according to a proposed prediction equation with a correlation coefficient of 0.7517. The average surface hardness of the fabricated PU foam part has a Shore O hardness value of approximately 75. Foam parts made with 1.5 g of water added to 15 g of a foaming agent have the fewest internal pores, resulting in the densest interior. PU foam parts exhibit excellent mechanical properties when 3 g of water is added to the PU foaming agent, as evidenced by their surface hardness and compressive strength. Using rigid PU foam parts as a backing material in the proposed method can reduce rapid tool production costs by about 62%. Finally, an innovative manufacturing process for creating large SRMs using rigid PU foam parts as backing material is demonstrated.

Exploring the effects of angle of incidence on stabbing resistance in advanced protective textiles: Novel experimental framework and analysis

Despite numerous research investigations to understand the influences of various structural parameters, to the authors' knowledge, no research has been the effect of different angles of incidence on stab response and performance of different types of protective textiles. Three distinct structures of 3D woven textiles and 2D plain weave fabric made with similar high-performance fiber and areal density were designed and manufactured to be tested. Two samples, one composed of a single and the other of 4-panel layers, from each fabric type structure, were prepared, and tested against stabbing at [0°], [22.5°], and [45°] angle of incidence. A new stabbing experimental setup that entertained testing of the specimens at various angles of incidence was engineered and utilized. The stabbing bench is also equipped with magnetic sensors and a UK Home Office Scientific Development Branch (HOSDB)/P1/B sharpness engineered knives to measure the impact velocity and exerted impact energy respectively. A silicon compound was utilized to imprint the Back Face Signature (BFS) on the backing material after every specimen test. Each silicon print was then scanned, digitized, and precisely measured to evaluate the stab response and performance of the specimen based on different performance variables, including Depth of Trauma (DOT), Depth of Penetration (DOP), and Length of Penetration (LOP). Besides, the post-impact surface failure modes of the fabrics were also measured using Image software and analyzed at the microscale level. The results show stab angle of incidence greatly influences the stab response and performance of protective textiles. The outcome of the study could provide not only valuable insights into understanding the stab response and capabilities of protective textiles under different angle of incidence, but also provide valuable information for protective textile manufacturer, armor developer and stab testing and standardizing organizations to consider the angle of incidence while developing, testing, optimizing, and using protective textiles in various applications.

Hybrid Soft Ballistic Panel Packages with Integrated Graphene-Modified Para-Aramid Fabric Layers in Combinations with the Different Ballistic Kevlar Textiles.

The purpose of the research discussed in this article is to explore the possibility of creating hybrid soft ballistic panel (BP) package variants by integrating into their composition layers of graphene-modified para-aramid fabrics in combinations with the different ballistic Kevlar textiles to improve the durability of the first layers of the soft ballistic panel. To address this goal, the liquid-phase exfoliation (LPE) method was used for integrating dispersions into composites to solve a number of topical problems in the stages of the technological sequence development of processing methods and optimizing processing parameters in accordance with the processing specifics of aramid textiles to achieve the desired properties of modified ballistic fabric, including the provision of coating adhesion to the surface to be modified. To test the results, ballistic experiments were performed and the back-face signature (BFS) of bullet impact on a backing material was analysed according to standards. Bullet impacts on the first ballistic protective fabric layers were also studied.

Fabrication and Characterization of Microneedle Patches for Loading and Delivery of Exosomes.

Exosomes, as emerging "next-generation" biotherapeutics and drug delivery vectors, hold immense potential in diverse biomedical fields, ranging from drug delivery and regenerative medicine to disease diagnosis and tumor immunotherapy. However, the rapid clearance by traditional bolus injection and poor stability of exosomes restrict their clinical application. Microneedles serve as a solution that prolongs the residence time of exosomes at the administration site, thereby maintaining the drug concentration and facilitating sustained therapeutic effects. In addition, microneedles also possess the ability to maintain the stability of bioactive substances. Therefore, we introduce a microneedle patch for loading and delivering exosomes and share the methods, including isolation of exosomes, fabrication, and characterization of exosome-loaded microneedle patches. The microneedle patches were fabricated using trehalose and hyaluronic acid as the tip materials and polyvinylpyrrolidone as the backing material through a two-step casting method. The microneedles demonstrated robust mechanical strength, with tips able to withstand 2 N. Pig skin was used to simulate human skin, and the tips of microneedles completely melted within 60 s after skin puncture. The exosomes released from the microneedles exhibited morphology, particle size, marker proteins, and biological functions comparable to those of fresh exosomes, enabling dendritic cells uptake and promoting their maturation.

Development and optimization of the Glabridin-loaded dissolving microneedle for enhanced treatment of keloid

Glabridin (Gla) has been reported to have significant effects in scar treatment, and however, the water insolubility of Gla leads to its poor transdermal absorption ability, which affects its bioactivities. Therefore, we attempted to prepare the Gla dissolving microneedles (Gla-MN) to improve the absorbtion of Gla. After investigation of the 3 factors including the needle tip matrix concentration, the prescription concentration of backing material, and the dissolution method of Gla, we finally determined the process parameters of 10% hyaluronic acid (HA) as the needle tip and 5% polyvinyl alcohol (PVA) as the backing, according to which the Gla-MN was prepared with the good characteristics of high hardness, complete appearance and good in vitro dissolution ability. We then loaded Gla onto the microneedles and measured that the average drug loading of Gla-MN was 2.26 ± 0.11 μg/mg and the cumulative transdermal release of Gla-MN was up to 76.9% after 24 h. In addition, Gla-MN had good skin penetration properties, with Gla-MN penetrating at least 4 to 5 layers of parafilm. And the skin basically could return to normal after 4 h of piercing. Importantly, our results showed that Gla-MN had higher transdermal delivery and therapeutic effects against keloid than that of Gla at the same dosage.

Impact of a Projectile on Fabrics – An Experimental Test Method

Fabric manufacturers are striving to produce value-added, high-end technical fabrics, such as smart textiles, protective clothing and accessories for sports, where the performance of the fabric has become a decisive factor. Fabric impact resistance is one such property of importance. Therefore the development of a suitable method to predict the impact on the fabric at the point of fabric development is of great importance. In this article, the authors have attempted to design and develop a test method to predict fabric impact more accurately. A mathematical model has been developed to show the relationship between impact force, impact velocity and the depth of penetration on impact. Finally, test equipment has been developed to measure the impact based on the developed model. The indentation depth on impact was measured against both impact velocity and kinetic energy, and the experimental impact force was calculated against the impact velocity. It was found that the impact velocity of the projectile affects both the impact on fabric and indentation into the backing material as well as the energy absorbed by the fabric. The energy absorption also increased with impact velocity and higher velocities caused greater damage. No great variation in temperature was detected.

Reusing uncured Fiber-reinforced thermoset composite Prepreg waste with water-soluble PVA backing film

One challenge in reusing uncured composite prepreg waste is the removal of the backing film. Ensuring that no backing film remains during the reuse of composite prepreg material is crucial, as the presence of backing film in the laminate can contaminate the part, leading to defects such as delamination. Manual removal of the backing film from the leftover uncured composite prepreg is a labor-intensive task, and ensuring there is no remaining backing film in the prepreg waste can be challenging. To address these issues, the authors implemented a water-soluble polyvinyl alcohol (PVA) film as the backing material for the prepreg, allowing less labor-intensive removal of the PVA backing film by soaking the prepreg in water before reusing. In this study, 20 μm thick 100% PVA film was utilized as backing material for carbon fiber-reinforced thermoset composite prepreg. The performance of the PVA film as a prepreg backing material was assessed, and the process of removing the backing film was demonstrated. To investigate the impact of the backing film removal process on the mechanical properties of the reused prepreg, tensile and double cantilever beam (DCB) tests were conducted. The results indicated that the PVA backing removal and drying processes did not show any significant influence on the tensile properties and interlaminar strength of the reused composite prepreg. Furthermore, this study demonstrated the recycling of the PVA solution used in the backing removal process to produce new PVA film. The application of PVA as a backing film not only simplified the backing film removal for reused prepreg but also established a sustainable closed-loop recycling system for prepreg backing film.

3D Hybrid modeling for the ultrasonic phased array inspection of porosity in heavy plates: Simulation and experimental validation

Quantitative NDT modeling and simulation tools are important in design and fabrication of ultrasonic phased array probes with optimum characteristics and reduce the number of experimental efforts and development time. In order to achieve high accuracy (Amplitude deviation < 1 dB) with a low computational time in the simulation, the modeling tools require not only the high-frequency approximation of the ultrasonic wave propagation but also the high-precision electro-acoustic coupling model. This paper describes a computationally efficient 3D time-dependent hybrid model for the simulation of ultrasonic phased array inspection of porosity in heavy plates. This method combines the results of both 3D finite element analysis (PZFLex-FEA) and the semi-analytical ultrasonic simulation “Ray-Tracing”. As a first step, we demonstrate the FEA modeling of an ultrasonic phased array probe, which includes the full 1-3 piezocomposite design with the arrangement of array elements, conducting electrodes, multi-phase backing material, acoustical matching layer and electrical circuit of a 50 Ohm coaxial cable. In the current FEA simulation, we considered the acoustical and electrical cross-talk between the adjacent elements of an ultrasonic array sensor. In the second step, the FEA-simulated ultrasonic pulse-echo signal and its frequency spectrum of an array element in the farfield region are further used as the reference input signal in the CIVA-UT software to simulate the imaging of porosity in heavy plates, quantitatively. The design of the 3D wedge-geometry of the application specific array sensor is modeled and optimized using the CIVA raytracing and multi-phase backing models. The real excitation pulse of the industrial ultrasonic testing equipment “ROMIS (ROSEN Modular Inspection System)” is also included in the simulation to achieve high accuracy in the current hybrid modeling. The dependency of the detectability of the porosity on the frequency of the array sensor and the active element group so-called “Virtual Probe” are quantitatively analyzed. Finally, the 3D hybrid model simulated Time Corrected Gain (TCG) curves of the porosity like defects in the reference steel plates are compared with the real experiments and a good quantitative agreement is achieved.

Design, Fabrication and Performance Test of an Effective Body Armor

Aims: This original research paper targets an easy but efficient design and fabrication of a safe body armor. A test bed with weapons was another key aim. Therefore, it is essential to verify the vest’s capability to withstand rigorous stab tests as prescribed by the standard. Background: The most widely used armor piece is the torso-protecting overt (worn over the uniform or clothing) one. The main concern of this work was to design and develop such a stabresistant soft body armor made from readily available materials to protect against threats such as knives, blades, and sharp-tipped objects. Objectives: From the Mechanical Engineering point of view, the present research goals for such an armor vest were: low cost, moderately lightweight, comfortable, made from easily available materials, simple forward design, easy to fabricate, and the ability to adjust the level of protection without altering the primary design structure. The effectiveness of the vest needed to be verified through rigorous testing following relevant standards. Methods: The prototype of the stab-resistant armor was fabricated with two different configurations and their performance was rigorously tested in accordance with the NIJ Standard-0115.00 to determine its level of protection. Nylon-based panel elements covered with rubber and cotton-based panels were compared in terms of their ability to stop stab threats. Taking into account the key point of strike energy levels during the stabbing, test beds were created in the laboratory to rigorously conduct the required tests. Blades of two types were made, attached with fixtures, and dropped on the armors (upon backing material) in the test bed. Results: The ‘Complete Armor’ showed excellent performance against stab attacks. The tests revealed that the nylon-based panel elements covered with rubber were more successful in stopping stab threats compared to cotton-based panels. Conclusion: The designed and fabricated prototype of the stab-resistant soft body armor achieved the desired level of protection against stab threats. The armor is also cost-effective, it can be fabricated using locally available materials, at a cost of only 10 USD compared to 300 USD for commercially available armor. Other: However, it should be noted that stab resistance does not necessarily imply ballistic resistance, and no armor can provide invincibility against all types of threats.

An 8 mm endoscopic histotripsy array with integrated high-resolution ultrasound imaging

An 8 mm diameter, image-guided, annular array histotripsy transducer was fabricated and characterized. The array was laser etched on a 5 MHz, 1–3 dice and fill, PZT-5H/epoxy composite with a 45 % volume fraction. Flexible PCBs were used to electrically connect to the array elements using wirebonds. The array was backed with a low acoustic impedance epoxy mixture. A 3.6 by 3.8 mm, 64-element, 30 MHz phased array imaging probe was positioned in the center hole, to co-align the imaging plane with the bubble cloud produced by the therapy array. A custom 16-channel high voltage pulse generator was used to test the annular array for focal lengths ranging from 3- to 8-mm. An aluminum lens-focussed transducer with a 7 mm focal length was fabricated using the same piezocomposite and backing material and tested along with the histotripsy array. Simulated results from COMSOL FEM models were compared to measured results for low voltage characterization of the array and lens-focussed transducer. The measured transmit sensitivity of the array ranged from 0.113 to 0.167 MPa/V, while the lens-focussed transducer was 0.192 MPa/V. Simulated values were 0.160 to 0.174 MPa/V and 0.169 MPa/V, respectively. The measured acoustic fields showed a significantly increased depth-of-field compared the lens-focussed transducer, while the beamwidths of the array focus were comparable to the lens. The measured cavitation voltage in water was between 254 V and 498 V depending on the focal length, and 336 V for the lens-focussed transducer. The array had a lower cavitation voltage than the lens-focussed transducer for a comparable operating depth. The histotripsy array was tested in a tissue phantom and an in vivo rat brain. It was used to produce an elongated lesion in the brain by electronically steering the focal length from 3- to 8-mm axially. Real time ultrasound imaging with a Doppler overlay was used to target the tissue and monitor ablation progress, and histology confirmed the targeted tissue was fully homogenized.

The Effects of Target Thicknesses and Backing Materials on a Ti-Cu Collision Weld Interface Using Laser Impact Welding

This study demonstrates that the thickness of the target and its backing condition have a powerful effect on the development of a wave structure in impact welds. Conventional theories and experiments related to impact welds show that the impact angle and speed of the flyer have a controlling influence on the development of wave structure and jetting. These results imply that control of reflected stress waves can be effectively used to optimize welding conditions and expand the range of acceptable collision angle and speed for good welding. Impact welding and laser impact welding are a class of processes that can create solid-state welds, permitting the formation of strong and tough welds without the creation of significant heat affected zones, and can avoid the gross formation of intermetallic in dissimilar metal pairs. This study examined small-scale impact using a consistent launch condition for a 127 µm commercially pure titanium flyer impacted against commercially pure copper target with thicknesses between 127 µm and 1000 µm. Steel and acrylic backing layers were placed behind the target to change wave reflection characteristics. The launch conditions produced normal collision at about 900 m/s at the weld center, with decreasing impact speed and increasing angle moving toward the outer perimeter. The target thickness had a large effect on wave morphology, with the wave amplitude increasing with target thickness in both cases, peaking when target thickness is about twice flyer thickness, and then falling. The acrylic backing showed a consistently smaller unwelded central zone, indicating that impact welding is possible at a smaller angle in that case. Strength was measured in destructive tensile testing. Failure was controlled by the breakdown of the weaker of the two base metals over all thicknesses and backings. This demonstrates that laser impact welding is a robust method for joining dissimilar metals over a range of thicknesses.

Characterization of 235U, 238U and 239Pu fission ionization chamber foils by [formula omitted] and [formula omitted]-ray spectrometry

The masses of thin, electroplated deposits of 235U, 238U and 239Pu on titanium backings have been determined to better than 1.3% precision by employing three complementary measurement techniques: α spectrometry, 2π gas counting, and γ-ray spectrometry. A dedicated α spectrometer was designed and calibrated to allow for repeatable, high-precision measurements of the absolute α activity of a sample. The isotopic composition of the sample was determined by fitting the peaks in the α spectrum, a technique which was demonstrated to be generally consistent with mass spectrometry. Independently, the total activity of the deposits were measured in a 2π gas flow proportional counter. A detailed study of the effects of α particle straggling in the actinide deposit and α particle recoil off the sample backing material was performed. The masses of these actinide deposits were also measured via γ-ray spectrometry. We found that all three systematically independent techniques produced consistent results, and could be combined into a weighted average with further reduced uncertainty. The mass ratios of these actinide deposits were determined to better than 1% precision via α spectrometry, enabling high-precision fission cross section ratio measurements.

Dynamic measurement of ballistic impact using an optical fibre sensor

An optical fibre-based sensor is developed for measuring the dynamics of the back face deformation of soft body armor. The measurement system consists of embedding an optical fibre into a thin silicone mat to increase survivability. The silicone sensor mat is placed between the soft body armor and the backing material. The optical fibre experiences times of sticking and slipping. The portions of the impact with the optical fibre stuck are reconstructed into slipping-equivalent strain using exponential extrapolation from adjacent slipping portions. The strain on the optical fibre is related to the projectile acceleration when the optical fibre is slipping. The strain is measured with the optical fibre sensor using a fibre Bragg grating. The system is characterized using a gas gun in combination with high-speed imaging. The system is experimentally demonstrated at the Army Test Center in Aberdeen, MD. Of the 23 shots 17 had an error less than 10%.

The impact of backplate support conditions on ceramic fracture and energy absorption in the penetration resistance process of ceramic/metal composite armor

As the backing plate conditions significantly affect the ballistic performance of ceramic/metal composite armor, we have conducted impact experiments using 12.7 mm API projectiles (brittle-hard) to examine the influence of different material characteristics of metal backing plates on the ballistic impact performance of ceramic/metal composite armor. By weighing multilevel sieved fragments and employing the Rosin-Rammler fragment distribution model, we analyzed the influence of backing plate material parameters on the fragment size distribution patterns of the penetrator and ceramic panel. Further, we utilized numerical simulations to explore the impact of backing plate density, Young's modulus, and yield strength on ceramic fracture and energy absorption during penetration. Overall, a high-density backing plate provides better inertial support. Backing materials with a high Young's modulus can enhance the ballistic performance of the ceramic composite target, but there is a limit to this effect. The yield strength of the backing plate is not necessarily better when higher; instead, there is an optimal value. Either too high or too low yield strength can reduce the energy absorption efficiency of the ceramic.

Analysis of the Use of Different Backing Layer Materials in the Design of Alpha-Decay Sails for Interplanetary and Interstellar Travel

This paper analyzes the design of an alpha-decay sail. While previous studies have been conducted on the feasibility of alpha-decay sails, none have investigated the effects of different backing materials and backing material thicknesses on propulsion. This paper conducts simulations using the particle simulation toolkit Geant4 to determine the thrust produced from alpha-decay sails constructed of 238Pu and a backing layer made of aluminum, beryllium, lithium, or polyethylene. The results demonstrate that alpha-decay sails can be a very useful form of in-space propulsion, having the potential to dramatically decrease travel time beyond distances of 100 AU.

MRI compatibility testing of commercial high intensity focused ultrasound transducers

PurposeThe study aimed to compare the performance of eight commercially available single-element High Intensity Focused Ultrasound (HIFU) transducers in terms of Magnetic Resonance Imaging (MRI) compatibility. MethodsImaging of an agar-based MRI phantom was performed in a 3 T MRI scanner utilizing T2-Weighted Fast Spin Echo (FSE) and Fast low angle shot (FLASH) sequences, which are typically employed for high resolution anatomical imaging and thermometry, respectively. Reference magnitude and phase images of the phantom were compared with images acquired in the presence of each transducer in terms of the signal to noise ratio (SNR), introduced artifacts, and overall image quality. ResultsThe degree of observed artifacts highly differed among the various transducers. The transducer whose backing material included magnetic impurities showed poor performance in the MRI, introducing significant susceptibility artifacts such as geometric distortions and signal void bands. Additionally, it caused the most significant SNR drop. Other transducers were shown to exhibit high level of MRI compatibility as the resulting images closely resembled the reference images with minimal to no apparent artifacts and comparable SNR values. ConclusionsThe study findings may facilitate researchers to select the most suitable transducer for their research, simultaneously avoiding unnecessary testing. The study further provides useful design considerations for MRI compatible transducers.

Pin-less moisture meter comparison to pin-type moisture meters in gypsum board and the effect of backing materials on pin-less readings

Moisture meters are invaluable tools used in the building inspection industry. Little comparative data is available for pin-type (resistance) verse pin-less (capacitance) moisture meters. There is also a lack of data for pin-less moisture meters in regard to the effect of backing materials on the readings obtained. We present data comparing four common moisture meters used in building inspections and investigate the effect of backing materials on readings in gypsum board. Moisture readings taken by the Trotec and CEM meters correlated well with moisture readings taken with resistance measurements and comparison to gravimetric moisture content. The moisture meters varied in their responses to backing materials with the Trotec showing the smallest effects and the CEM showing the largest. Different moisture meters may be useful in different applications, and inspectors must carefully consider results from pin-less readings to obtain relevant data of moisture investigations.

Data-driven and physics-based modelling of process behaviour and deposit geometry for friction surfacing

In the last decades, there has been an increase in the number of successful machine learning models that have served as a key to identifying and using linkages within the process-structure–property-performance chain for vastly different problems in the domains of materials mechanics. The consideration of physical laws in data-driven modelling has recently been shown to enable enhanced prediction performance and generalization while requiring less data than either physics-based or data-driven modelling approaches independently. In this contribution, we introduce a simulation-assisted machine learning framework applied to the solid-state layer deposition technique friction surfacing, suitable for solid-state additive manufacturing as well as repair or coating applications. The objective of the present study is to use machine learning algorithms to predict and analyse the influence of process parameters and environmental variables, i.e. substrate and backing material properties, on process behaviour and deposit geometry. The effects of maximum process temperatures supplied by a numerical heat transfer model on the predictions of the targets are given special attention. Numerous different machine learning algorithms are implemented, optimized and evaluated to take advantage of their varied capabilities and to choose the optimal one for each target and the provided data. Furthermore, the input feature dependence for each prediction target is evaluated using game-theory related Shapley Additive Explanation values. The experimental data set consists of two separate experimental design spaces, one for varying process parameters and the other for varying substrate and backing material properties, which allowed to keep the experimental effort to a minimum. The aim was to also represent the cross parameter space between the two independent spaces in the predictive model, which was accomplished and resulted in an approximately 44 % reduction in the number of experiments when compared to carrying out an experimental design that included both spaces.

Sustainable Perforated Acoustic Wooden Panels Designed Using Third-Degree-of-Freedom Bezier Curves with Broadband Sound Absorption Coefficients.

The current interior design scope places high demands on acoustic treatment manufacturers. The state of the art does not provide satisfactory material proposals for architects to satisfy design needs. There is a need for a novel approach concerning decorative, recognized materials that adapts them to the acoustic surface properties. The final design proposed in this study presents a modern functional solution with high acoustic properties, which can be produced with sustainable materials such as FSC wood and has a low environmental impact because of its low waste production. This research presents the complete design process of a novel type of wooden acoustic panel. A comprehensive explanation of the scientific development is covered, including basic material testing in an impedance tube, FEM simulations of the initial designs, and final measurements in a reverberation chamber. The solution's novelty is based on the optimized placement of the perforation holes on the surface of a wooden overlay using a ship deck optimization algorithm. The methods used cover the original solution of mixing FEM modeling of the surface impedance with the application of the Jeong-Thomasson correction for random incidence sound absorption coefficient simulation. The contribution of this research is the development of wooden perforated panels with Class A sound absorption and an overall depth of 90 mm, including the 50 mm depth of the backing material. The discussion will explain the difficulties of working with this material and the need for a combination of the aesthetic and acoustic sides of the project.