Background Gas Research Articles

Particle-in-cell simulations of EUV-induced hydrogen plasma in the vicinity of a reflective mirror

Particle-In-Cell (PIC) simulations were performed in this work to study the dynamics of the EUV-induced hydrogen plasma. The Monte-Carlo Collision (MCC) model was employed to deal with the collisions between charged particles and background gas molecules. The dynamic evolution of the plasma sheath, as well as the flux and energy distribution of ions impacting on the mirror surface, was discussed. It was found that the emission of secondary electrons under the EUV irradiation on the ruthenium mirror coating creates a positively charged wall and then prevents the ions from impacting on the mirror and therefore changes the flux and energy distribution of ions reaching the mirror. Furthermore, gas pressure has a notable effect on the plasma sheath and the characteristics of the ions impinging on the mirrors. With greater gas pressure, the sheath potential decreases more rapidly. The flux of ions received by the mirror grows approximately linearly and at the same time the energy corresponding to the peak flux decreases slightly. However, the EUV source intensity barely changes the sheath potential, and its influence on the ion impact is mainly limited to the approximate linear increase in ion flux.

Characterization of an RF-excited broad beam ion source operated with a mixture of CHF3 and O2

The composition and ion energy distributions of the main ion species of an ion beam were recorded and analyzed. The RF-type broad beam ion source was operated with a mixture of CHF3 and O2. A plasma bridge neutralizer operating with Ar was employed for ion beam neutralization. The data were collected with an energy-selective mass spectrometer (ESMS). The mass spectrum showed numerous ion species, beginning with ionized molecules, dissociation products of the process gases and products from reactions with background gas and the plasma discharge vessel, and the extraction system. For a quantification of the ion beam composition, the mass dependent transmission functions for two ESMS were determined. The ion energy distributions show that, in comparison to operation with inert gases, there are additional slower ions present. These ions can be related to dissociation processes outside of the ion beam source. As a result of their typically lower etching yield, these slower ions affect the etching behavior.

Latent-to-sensible heat conversion kinetics during nanoparticle coalescence.

Coagulational growth in an aerosol is a multistep process; first particles collide, and then they coalesce with one another. Coalescence kinetics have been investigated in numerous prior studies, largely through atomistic simulations of nanoclusters (102-104 atoms). However, with a few exceptions, they have either assumed the process is completely isothermal or is a constant energy process. During coalescence, there is the formation of new bonds, decreasing potential energy, and correspondingly increasing internal kinetic (thermal) energy. Internal kinetic energy evolution is dependent not only on coalescence kinetics but also on heat transfer to the surrounding gas. Here, we develop and test a model of internal kinetic energy evolution in collisionally formed nanoclusters in the presence of a background gas. We find that internal kinetic energy dynamics hinge upon a power law relationship describing latent-to-sensible heat release as well as a modified thermal accommodation coefficient. The model is tested against atomistic models of 1.5-3.0nm embedded-atom gold nanocluster sintering in argon and helium environments. The model results are in excellent agreement with the simulation results for all tested conditions. Results show that nanocluster effective temperatures can increase by hundreds of Kelvin due to coalescence, but that the rise and re-equilibration of the internal kinetic energy is strongly dependent on the background gas environment. Interestingly, internal kinetic energy change kinetics are also found to be distinct from surface area change kinetics, suggesting that modeling coalescence heat release solely due to surface area change is inaccurate.

Effect of nitrogen/oxygen ratios on surface charge distributions generated by repetitive surface dielectric barrier discharges

Studies on the dielectric surface parameters and dielectric barrier discharges (DBD) characteristics considering the influence of gases in DBD on the surface charge distribution are scarce. Thus, to overcome this research gap, this study measured the potential distributions of AC-driven surface DBD in oxygen (O2), synthetic air and nitrogen (N2) as background gases using the Pockels effect. The results showed that the patterns of the filamentary discharges generated during the positive voltage polarity phase differed depending on the O2 ratio. In addition, the electrostatic repulsion forces between the residual charge and the newly created filament were analysed from the measured potential distribution and the greatest effect was observed in air, rather than in N2 and O2. The potential distribution was transformed into a charge density distribution and compared with the discharge luminescence in air and N2. The results showed that the shape of the filament tip differed between the charge density and discharge luminescence only in the case of air, which was attributed to the effect of attachment reactions on the formation of residual charge. The measurements showed that in a surface discharge, similar to the case in a volume discharge, the photoionisation and ionisation coefficients significantly affected the geometrical properties of the discharges.

Oxygen diffusion in freestanding body centered cubic tantalum structural thin films in air and in high vacuum

Sensors and actuators constructed from freestanding tantalum thin films show promise for micromachining applications and for the study of thin film mechanical behavior. To assess this promise, it is necessary to gain further understanding of the performance of Ta as a structural material. We first evaluate the coefficient of thermal expansion, αTa, using micromachined bent beams, which amplify displacement compared to linear expansion. The value for αTa is 6.8 × 10−6 m/m °C, in good agreement with the bulk value. This validation enables the study of interstitial oxygen diffusion in Ta, for which literature values of activation energy vary widely, from 0.60 to 1.98 eV. Displacement in air due to oxygen diffusion becomes measurable after 30 min exposure at 180 °C. We extract an activation energy for interstitial oxygen in Ta of 0.53 eV/atom. Analysis indicates that lattice rather than grain boundary diffusion is the associated mechanism. To inhibit the oxidation, we construct a thermal stage that controls specimen temperature in 10−5 Pa vacuum. Then, after a 24 h hold, oxidation is suppressed up to 400 °C. This result is discussed in terms of O dissolution from its native oxide, coupled with further absorption from background gases.

Analysis of the trigger characteristics for a pseudospark switch triggered by nanosecond focused laser

Clarifying the trigger characteristics of pseudospark switch triggered by laser (backlight thyratron, BLT) is crucial for optimizing the trigger performance under different conditions. This paper investigates the electron and ion emission characteristics of metal irradiated by nanosecond focused laser, and tests the trigger characteristics of BLT triggered from the back of the cathode (CBLT) and the back of anode (ABLT) with different targets (Mg, Ti, Cu, Mo, W), and discusses the trigger mechanism. The trigger characteristics of CBLT depends on the emission of prompt electrons e1 and the expansion of ultrafast electrons e2. When the laser energy ε is less than 0.3 mJ, there will be no e1 emission, and low-density metals (e.g. Mg and Ti) are prone to ablation, resulting in large e2 amplitude and short trigger delay td. Due to the slow speed of e2, td of CBLT has an exponential relationship with the laser irradiation position. When ε is increased to above 1 mJ, different metals can be fully heated, and the emission of e1 will be enhanced and play a major role in trigger. In this case, metals with high melting and boiling points will produce more e1, so the trigger performance of Mg is the worst and W is the best. Due to the fast speed of e1, the sensitivity of td of CBLT triggered by e1 to the laser irradiation position is low, and the trigger lifetime can be improved by fine-tuning the laser irradiation position. The trigger of ABLT depends on the expansion of fast ions i2, and heavy metal ions diffuse easily in the background gas, so the laser irradiation area where ABLT can be stably triggered is larger, and the corresponding trigger performance of ABLT is better.

Dynamics of Star Cluster Formation: Mergers in Gas-rich Environments

We perform high-resolution simulations of forming star clusters as they merge inside giant molecular clouds (GMCs) using hydrodynamics coupled to N-body dynamics to simultaneously model both the gas and stars. We zoom in to previously run GMC simulations and resolve clusters into their stellar and gas components while including the surrounding GMC environment. We find that GMC gas is important in facilitating the growth of clusters in their embedded phase by promoting cluster mergers. Mergers induce asymmetric expansion of the stellar component of the clusters in our simulations. As well, mergers induce angular momentum in the clusters’ stellar and gas components. We find that mergers can lead to an increase in the amount of dense gas present in clusters if a background gas distribution is present. We predict that this can lead to new star formation that can change the overall distribution of cluster stars in velocity space. Our results suggest that subcluster mergers in the presence of background gas can imprint dynamical signatures that can be used to constrain cluster formation histories.

Laser-induced breakdown spectroscopy for helium detection in beryllium coatings

Laser Induced Breakdown Spectroscopy (LIBS) method is considered to be a promising tool for analyzing the retention of hydrogen isotopes (D and T) and helium (He) on the first walls and divertor regions of future fusion reactors. Helium will be produced in DT reactions but could also be used in the initial non-nuclear phases of DEMO concepts. The present study investigates the He detection by LIBS method in the Be coatings simulating the deposits on the divertor plasma-facing components of JET while the results are also relevant for He detection in the deposits of other wall materials. The study was carried out in a vacuum vessel filled with 2–40 mbar argon background gas. It was shown that 2.8 at. % of He was confidently detectable by LIBS at optimized measurement conditions and the estimated limit of detection at used experimental conditions is approximately 0.7 at. %. The intensity of the He emission line at 587.56 nm was the strongest at the center of the laser-induced plasma plume. The He line intensity increased with the pressure of Ar gas but the broadening of the He line and the increase of the background emission and noise set an upper limit to the Ar background pressure usable for He detection. The application of the calibration-free LIBS procedure resulted in the overestimation of the He/Be ratio by several orders of magnitude. The overestimation can be explained by the deviation of LIBS plasma from the local thermodynamic equilibrium, which is caused by the very high excitation energy of He atoms.

Two-term Boltzmann approximation versus Monte-Carlo simulation: effect of magnetic field

In this paper, we investigate the spatial-local electron energy distribution function (eEDF) interacting with a background gas at the sub-atmospheric pressure in a wide range of applied crossed electric and magnetic fields using the Boltzmann kinetic equation. We compare solutions obtained using two numerical approaches (deterministic two-term approximation and stochastic Monte Carlo method) to identify their applicability in the context of determining drift velocity and reaction constants for electrons. For argon and helium, the upper limit of the reduced electric field applicability of the two-term approximation is discussed. It has been shown that the presence of a magnetic field can reduce this limit. Two explanations are given, one is based on the math of two-term formalism, and the other is based on velocity-space analysis. Two-term approximation fails due to it’s inability to resolve underlying cyclotron oscillation (it should result in an energy variation along the electron’s trajectory). The absence of this feature causes an incorrect estimation of momentum-transfer rate. This results an inaccuracy in the estimation of the angle between electric field and drift velocity.

Process simulation, optimization, and cost analysis of a proposed sulfur recovery unit by applying modified Claus technology

Removing sour gas from any suitable gas sweetening technology in a cost-effective and environmentally responsible manner is a major challenge. This paper discusses how to safely and economically dispose of small amounts of acid gases resulting from the amine sweetening process. A two-stage Claus desulfurization unit was studied and simulated to treat acid gases resulting from natural gas sweetening operations in Ras Gharib oil fields (Egypt). These acid gases are used as feedstock for the proposed plant to produce a valuable product, such as elemental sulfur, which is used as a raw material in many industries. Although many sulfur recovery techniques are available for various conditions and applications, the Claus process is a critical and widely used method for recovering elemental sulfur from gaseous hydrogen sulfide. This work represents the potential benefits of treating acid gases with high hydrogen sulfide content. In addition, operational variables that could affect sulfur production and sulfur recovery efficiency of the studied Claus unit were studied and optimized. Aspen HYSYS simulation software (version 9) was used to evaluate the economic aspects and optimize the operational parameters of the unit for producing sulfur from acid background gases. The results showed that the maximum sulfur production was achieved at a catalytic converter reactor temperature of 270 °C and 210 °C for the first and second catalytic reactor, respectively, with an air flow rate of 933.3 kg mol/h. The economic study of the proposed desulfurization unit showed that the Claus unit would be economically acceptable with an expected return on investment of approximately 10% and an average payback period of 10 years. Moreover, the introduced plant has a positive impact on the environment by reducing the concentration of hydrogen sulfide in the gas from 69.58 to 0.16%.

Low energy femtosecond pulsed laser ablation of Nd:YAG laser crystal in high-pressure oxygen and nitrogen background gas

A low-energy femtosecond (fs) pulsed laser was utilized to ablate the Nd:YAG laser crystal target in high-pressure oxygen (O2) and nitrogen (N2) background gases. Only minute amounts of neodymium (Nd), yttrium (Y), and aluminum (Al) were detected in the deposited material due to the thermalization resulting from low laser pulse energy and significant scattering caused by the high background gas pressure. We used a collision-based model and peak-fitting method of the angular distribution of the plume to explain the result. The collision-based model was used to explain and determine the probability distribution of the elements arriving from the target to the substrate. The magnitude of the probability distribution obtained with O2 background gas is higher as compared to N2 background gas owing to the former’s higher collision frequency. The peak-fitting method of the angular distribution of Nd, Y, and Al provided better approximations of the ratio of atoms arriving after ablation as compared to the collision-based model. Further improvements can be carried out to better predict the deposited material ratio.

Modelling of plasma discharge in a filament negative ion source

Most of the currently operating Negative ion Neutral Beam Injectors (N-NBIs) exploit filament powered sources for the generation of beam ions. Being widely used in fusion experiments, the filament arc technology has been thoroughly investigated and optimized over the years, allowing to achieve excellent performances in terms of extracted beam optics. The source geometry, the magnetic field topology and the arc power strongly influence both the plasma discharge and the background gas properties and, consequently, the beam features. In this framework, this contribution describes a numerical investigation of the plasma properties in a filament-powered negative ion source, performed by means of a 2D3V Particle In Cell-Monte Carlo Collisions (PIC-MCC) code. Specifically, we discuss plasma formation by the thermionic electrons emitted by the filaments, investigating their interaction with the background gas. We also study the plasma diffusion through the magnetic filter field and how the latter modifies plasma density, electron temperature and plasma potential along the axial direction when approaching the plasma facing electrode.

Phase and Morphology of Water-ice Grains Formed in a Cryogenic Laboratory Plasma

Grains of ice are formed spontaneously when water vapor is injected into a weakly ionized laboratory plasma in which the background gas has been cooled to cryogenic temperatures comparable to those of deep space. These ice grains are levitated indefinitely within the plasma so that their time evolution can be observed under free-floating conditions. Using microscope imaging, ice grains are shown to have a spindle-like fractal structure and grow over time. Both crystalline and amorphous phases of ice are observed using Fourier transform infrared spectroscopy. A mix of crystalline and amorphous grains coexists under certain thermal conditions, and a linear mixing model is used on the ice absorption band surrounding 3.2 μm to examine the ice phase composition and its temporal stability. The extinction spectrum is also affected by inelastic scattering as grains grow, and characteristic grain radii are obtained from Mie scattering theory and compared to size measurements from direct imaging. Observations are used to compare possible ice nucleation mechanisms, and it is concluded that nucleation is likely catalyzed by ions, as ice does not nucleate in the absence of plasma and impurities are not detected. Ice grain properties and infrared extinction spectra show similarity to observations of some astrophysical ices observed in protoplanetary disks, implying that the fractal morphology of the ice and observed processes of homogeneous ice nucleation could occur as well in such astrophysical environments with weakly ionized conditions.

Rubber-like PTFE Thin Coatings Deposited by Pulsed Electron Beam Deposition (PED) Method.

PTFE coatings were manufactured using the pulsed electron beam deposition (PED) technique and deposited on Si substrates. The deposition was carried out at constant parameters: temperature 24 °C, discharge voltages 12 kV, and 5000 electron pulses with a pulse frequency of 5 Hz. Nitrogen was used as the background gas. The gas pressure varied from 3 to 11 mTorr. The coating adhesion was evaluated using micro scratch testing and the residual scratch morphology was characterized by atomic force microscopy. Detailed studies of the chemical and physical structure were conducted using infrared spectroscopy and X-ray diffraction. These analyses were then correlated with the mechanical response of the coatings observed during the scratch tests. Drawing upon a review of the literature concerning energetic beam interactions with PTFE material, hypotheses were posed to explain why only specific conditions of the PED process yielded PTFE coatings with rubber-like properties.

Properties of collisional plasma sheath with ionization source term and two-temperature electrons in an oblique magnetic field

A collisional magnetized plasma sheath with two groups of electrons has been studied using a fluid model including the effects of the ionization source term and the collisional force between ions and neutral atoms. Two kinds of non-Maxwellian descriptions of electron velocity distribution, non-extensive distribution and truncated distribution, are applied in the model, and the ionization effects of both kinds are considered. By applying Sagdeev potential, the modified Bohm sheath criterion is derived. The effects of ionization, magnetic field, and high-temperature electron concentration ratio on plasma sheath density, potential, sheath thickness, and ion kinetic energy are studied. In cases with high background gas density, ion density accumulates at the sheath edge position, forming a peak and manifesting as a rapid drop in the potential profile. The distribution characteristics of electrons have a significant impact on the transport properties of ions. Oscillations and non-monotonic characteristics of net charge near the sheath edge occur as the magnetic field angle increases, leading to an increase in the sheath layer width. It can be seen that in the case of a collisional sheath structure with high-temperature electrons, it is essential to consider the sheath changes induced by the ionization and the collisional force. Compared to a symmetric electron velocity distribution, the actual thickness of the sheath layer in a truncated electron distribution assumption could be significantly reduced.

Effect of background gas composition on the stoichiometry and lithium ion conductivity of pulse laser deposited epitaxial lithium lanthanum tantalate (Li3xLa1/3−xTaO3)

Lithium lanthanum tantalate (Li3xLa1/3−xTaO3, x = 0.075) thin films were grown via pulsed laser deposition using background gas atmospheres with varying partial pressures of oxygen and argon. The background gas composition was varied from 100% to 6.6% oxygen, with the pressure fixed at 150 mTorr. The maximum ion conductivity of 1.5 × 10−6 S/cm was found for the film deposited in 100% oxygen. The ion conductivity of the films was found to decrease with reduced oxygen content from 100% to 16.6% O2 in the background gas. The 6.6% oxygen background condition produced ion conductivity that approached that of the 100% oxygen condition film. The lithium transfer from the target to the film was found to decrease monotonically with decreasing oxygen content in the background gas but did not account for all changes in the ion conductivity. The activation energy of ion conduction was measured and found to correlate well with the measured ion conductivity trends. Analysis of x-ray diffraction results revealed that the films also exhibited a change in the lattice parameter that directly correlated with the ion conduction activation energy, indicating that a primary factor for determining the conductivity of these films is the changing size of the ion conduction bottleneck, which controls the activation energy of ion conduction.

Downhole detection of gas kick using low-frequency elastic wave: Multiphysics modeling and its implications

Gas kick is a common and high-risk drilling trouble in geo-energy engineering, especially for deep-water drilling and ultra-deep well drilling. The most favorable way of early detection of gas kick is to move the detection from the wellhead or near surface to the downhole. In this paper, a new conception of downhole detection of gas kick using low-frequency elastic wave was put forward. The framework of coupling the multiple physic processes of gas-liquid two-phase annulus flow, bubble migration and low-frequency elastic wave propagation during gas kick was developed. The characteristic responses of low frequency elastic wave to gas kick were quantitatively analyzed based on multiphysics modeling under the ideal case and different levels of background gas (BGG), respectively. The modeling results indicated that: (i) The velocity decreases cliff-like and the attenuation coefficient increases significantly at the gas-kick bubble front. The change magnitudes of the velocity and the attenuation coefficient increase with the gas intrusion rate, and decrease with the pump displacement. The change magnitude of attenuation coefficient decreases with mud density, while the increase of velocity is not sensitive to the mud density. (ii) For the ideal case of the vertical well, the effective detection within the depth section of (2014–2568) meter could identify gas kick about (14.3–29.2) minutes earlier than the conventional pit-gain method. The gas kick could be identified earlier when the deviation angle is smaller and/or the monitoring point goes deeper. (iii) The changing magnitudes and rates of the velocity and the attenuation coefficient decrease with the BGG. The downhole detection of gas kick using low-frequency elastic wave should be reliable when the BGG is lower than 5%. The effects of rock cuttings, phase transition of the gas, and drill-string vibrations should be further investigated in future study.

Initiation mechanism of arcing generated in RF capacitively coupled plasma

In our previous study, we established an arcing generation and measurement system and we observed prior light emission before arcing current development. However, we briefly analyzed those light emissions with strong assumptions without detailed experiment evaluations and thus, the investigation of the formation mechanism in the initiation phase with detailed experiment evaluations has yet to be conducted. In this work, we investigated the initiation mechanism of arcing generated on an arcing inducing probe (AIP) in a radio frequency capacitively coupled plasma (CCP) environment. Here, the AIP is an aluminum rod covered by anodized film and its tip edge is partially stripped to localize arcing on this edge. We measured emission light, voltage, and current waveforms induced by arcing. The spatiotemporal image of the emission light revealed that the tip glow is the brightest intensity and has longest lifetime during arcing, meaning that it is the primary process in whole arcing process. The current waveform induced by arcing corresponds to the time evolution of the tip glow and estimations revealed that the electron emission is the predominant component of the current formation. Furthermore, snapshot images with AIPs having enlarged stripping area exhibited that arcing occurs at the boundary between the alnuminum and anodized film (dielectric), where charging of ions from the CCP on the film surface can induce high-electric field. In addition, we found that the energy relaxation length of emitted electrons for collisions with Ar atoms, which are the background gas, is much larger than the tip glow diameter, meaning that the electon-Ar collision cannot maintain tip glow. This result supports additional source of atoms to sustain the tip glow such as the surface evaporation from arcing spot, of which evidence was speculated our previous study. We estimated minimum aluminum vapor density and surface temperature, which is sufficiently high enough to induce surface vaporization. Combining those experiment results and estimations, that are electron emission, high surface temperature, and surface evaporation, we can speculate that the initiation mechanism of arcing near dielectric surface in radio-frequency CCP environment is the thermionic emission and surface evaporation from arcing spot.

Investigation of high field plasma dynamics in a laser-produced plasma expanding into a background gas

This paper presents an overview of experimental results of a laser-produced plasma expanding into a background gas, immersed within a large range of highly uniform magnetic fields (of up to 3 T), that are transverse to the expanding plasma. We used intensified gated imaging to capture the expansion of the plasma across and along the magnetic field lines to observe the spatiotemporal expansion dynamics for different magnetic field strengths. We observe changes in the perpendicular and parallel dynamics of the laser-produced plasmas expansion at high magnetic field. In addition, our results have also indicated the presence of electron-ion hybrid instabilities at relatively high pressures (100 mTorr) and relatively high magnetic field strengths (2 T), in accordance with theoretical calculations.

Dielectric Behavior and Prolate Growth Patterns of Silicon Clusters SiN with N = 12-30 by Cryogenic Electric Beam Deflection.

We present a comprehensive investigation of the dielectric behavior and geometric structures of cold neutral SiN clusters of intermediate size with N = 12-30 atoms. For this, cryogenic electric beam deflection experiments were carried out for the first time for Si clusters at nozzle temperatures below 30 K. In combination with quantum chemical calculations based on density functional theory and classical trajectory simulations of the rotational dynamics in the electric field, the geometric structures of the clusters are discriminated. Clusters with N < 15 favor a single-capped square antiprism as a nucleus for cluster growth, forming compact geometries in the molecular beam. Starting with 15 atoms, a prolate-like growth is observed. The prolate structures are based on stable building blocks which reappear for numerous sizes throughout the cluster growth. Finally, the transition from prolate to quasi-spherical shapes is shown to take place around Si29/Si30 as predicted theoretically by the literature. The influence of the exchange-correlation functional on the predicted structure and dielectric properties is discussed in detail for some clusters. Relaxation of the electric-dipole moment and therefore quenching of the observed electric response due to vibrational excitation and collisions with the background gas are also considered, which explains deviations between experiment and theory.