pH Of Background Electrolyte Research Articles

Combined use of [TBA][L-ASP] and hydroxypropyl-β-cyclodextrin as selectors for separation of Cinchona alkaloids by capillary electrophoresis

In this paper, a new capillary electrophoresis (CE) separation and detection method was developed for the chiral separation of the four major Cinchona alkaloids (quinine/quinidine and cinchonine/cinchonidine) using hydroxypropyl-β-cyclodextrin (HP-β-CD) and chiral ionic liquid ([TBA][L-ASP]) as selectors. Separation parameters such as buffer concentrations, pH, HP-β-CD and chiral ionic liquid concentrations, capillary temperature, and separation voltage were investigated. After optimization of separation conditions, baseline separation of the three analytes (cinchonidine, quinine, cinchonine) was achieved in fewer than 7min in ammonium acetate background electrolyte (pH 5.0) with the addition of HP-β-CD in a concentration of 40mM and [TBA][L-ASP] of 14mM, while the baseline separation of cinchonine and quinidine was not obtained. Therefore, the first-order derivative electropherogram was applied for resolving overlapping peaks. Regression equations revealed a good linear relationship between peak areas in first-order derivative electropherograms and concentrations of the two diastereomer pairs. The results not only indicated that the first-order derivative electropherogram was effective in determination of a low content component and of those not fully separated from adjacent ones, but also showed that the ionic liquid appeared to be a very promising chiral selector in CE.

Quantitative determination of potassium hydrogenperoxomonosulfate in “Ecocid S” disinfectant by cathodic voltammetry

The electrochemical behaviour of potassium hydrogenperoxomonosulfate (KHSO5) in the presence of sodium dodecylbenzenesulfonate (SDBS) has been studied using cathodic voltammetry at the carbositall electrode as indicating in the potential range of +1.0…–1.2 V (the reference electrode Ag, AgCl/KСl(sat)) (Ep = +0.3 V). It has been experimentally proven that the height of KHSO5 reduction peak decreases and the potential of the reduction peak is shifted toward more electronegative values with increasing of the background electrolyte pH from 0.80 to 7.17. The maximum peak (Ip) occurs at a pH of approximately 0.8 and at a pH around 5 the analytical signal almost disappears. The effect of pH on the peak potential (Ep) shows the following: when the pH value increases in the interval from 0.8 to 2, Ep remains almost constant, but Ep decreases sharply to the negative value with pH increasing over 2. It has been experimentally proven that SDBS leads to increase of the current peak and the peak potential shifts to the more electropositive side (+0.25→ +0.3V). The influence of the present SDBS has been examined. The current peak increases with the concentration of the surfactant up to 1.2×10–3 mol L–1 and then stays almost constant with the increase in the concentration of SDBS above 3.0×10–3 mol L–1. The linear relationship was observed in the KHSO5 concentration range of (1.8–9.0)×10–5 mol L–1, the calibration curve equation was Iр = (4.3±1.1)×104 с (r = 0.998). When determining KHSO5 in the test solution of “Ecocid S” disinfectant with the concentrations of 4.65×10–5, 6.20×10–5 and 7.75×10–5 mol L–1) the RSDs were 0.025, 0.023 and 0.021, respectively (δ = –0.64 ... +0.16%); LOD = 6.50×10–6 mol L–1, LOQ = 2.17×10–5 mol L–1.

Synthesis and application of a chiral ionic liquid functionalized β‐cyclodextrin as a chiral selector in capillary electrophoresis

A novel chiral ionic liquid functionalized β-cyclodextrin, 6-O-2-hydroxpropyltrimethylammonium-β-cyclodextrin tetrafluoroborate ([HPTMA-β-CD][BF4]), was synthesized and used as a chiral selector in capillary electrophoresis. [HPTMA-β-CD][BF4] not only increased the solubility in aqueous buffer in comparison with the parent compound, but also provided a stable reversal electroosmotic flow, and the enantioseparation of eight chiral drugs was examined in phosphate buffer containing [HPTMA-β-CD][BF4] as the chiral selector. The effects of the [HPTMA-β-CD][BF4] concentration and the background electrolyte pH were studied. Moreover, the chiral separation abilities of β-CD and [HPTMA-β-CD][BF4] were compared and possible mechanisms for the chiral recognition of [HPTMA-β-CD][BF4] are discussed.

Offline and online capillary electrophoresis enzyme assays of β-N-acetylhexosaminidase

Enzyme assays of β-N-acetylhexosaminidase from Aspergillus oryzae using capillary electrophoresis in the offline and online setup have been developed. The pH value and concentration of the borate-based background electrolyte were optimized in order to achieve baseline separation of N,N',N″-triacetylchitotriose, N,N'-diacetylchitobiose, and N-acetyl-D-glucosamine. The optimized method using 25 mM tetraborate buffer, pH 10.0, was evaluated in terms of repeatability, limits of detection, quantification, and linearity. The method was successfully applied to the offline enzyme assay of β-N-acetylhexosaminidase, which was demonstrated by monitoring the hydrolysis of N,N',N″-triacetylchitotriose. The presented method was also utilized to study the pH dependence of enzyme activity. An online assay with N,N'-diacetylchitobiose as a substrate was developed using the Transverse Diffusion of Laminar Flow Profiles model to optimize the injection sequence and in-capillary mixing of substrate and enzyme plugs. The experimental results were in good agreement with predictions of the model. The online assay was successfully used to observe the inhibition effect of N,N'-dimethylformamide on the activity of β-N-acetylhexosaminidase with nanoliter volumes of reagents used per run and a high degree of automation. After adjustment of background electrolyte pH, an online assay with N,N',N″-triacetylchitotriose as a substrate was also performed.

Simulation of the effects of complex‐formation equilibria in electrophoresis: III. Simultaneous effects of chiral selector concentration and background electrolyte pH

This paper describes the results of the second-level testing of the simulation program Simul 5 Complex. We compare the published experimental results with the simulated migration behavior of the enantiomers at different pH and chiral selector concentration values and use the same optimization object function, separation selectivity, as the original papers. Simul 5 Complex proved to be a suitable tool for the prediction of the effective mobilities, separation selectivities, and migration order reversals in these pH-dependent and CD concentration dependent enantiomer separations. In addition, by performing simulations of four different separations systems (both real and model systems), Simul 5 Complex revealed the existence of unexpected and hitherto unexplained electromigration dispersion effects that were caused by the complexation process itself and could significantly impair the quality of the separations.

Analysis of Volatile Components in Curcuma Rhizome by Microemulsion Electrokinetic Chromatography

Volatile chemicals are a group of very important compounds in natural products. Curcuma rhizome, which contains many bioactive volatile compounds, is a traditional Chinese medicine that has long been used for the treatment of several diseases. In the present study, a microemulsion electrokinetic chromatography (MEEKC) method was developed for the analysis of four volatile components in Curcuma rhizome, including germacrone, furanodiene, curcumenol and curdione. Experimental parameters, including the pH, type and concentrations of background electrolyte, and microemulsion compositions (type and concentrations of surfactant, co-surfactant and oil phase) were intensively investigated. Finally, the primary compounds in the methanol extract of Curcuma rhizome were separated within 30 min using a running buffer composed of 2.31% w/v (80 mmol/L) sodium dodecyl sulfate (SDS), 0.91% w/v (80 mmol/L) 1-octane, 6.95% w/v (937.5 mmol/L) 1-butanol and 1.88% w/v (312.5 mmol/L) propanol in a 5-mM borate buffer (pH 8.1). The contents of the four investigated compounds were determined in the rhizome from C. phaeocaulis. The results showed that the developed MEEKC method provided an alternative tool for the analysis of volatile components, especially those of heat-sensitive compounds from natural products.

Enantiomeric separation and determination of the enantiomeric impurity of armodafinil by capillary electrophoresis with sulfobutyl ether-β-cyclodextrin as chiral selector.

A selective capillary electrophoresis method using sulfobutyl ether-β-cyclodextrin as a chiral selector was developed and validated for the determination of the enantiomeric impurity of (R)-modafinil, i.e., armodafinil. Several parameters were optimized for a satisfactory enantioresolution, including the type and concentration of chiral selector and organic modifier, pH of background electrolyte (BGE), capillary temperature. The finally adopted condition was: 20 mmol/L phosphate buffer at pH 7.5, containing 20 mmol/L sulfobutyl ether-β-cyclodextrin and 20% methanol, at temperature of 25 °C. A good resolution of 3.3 for the two enantiomers of modafinil was achieved by applying the optimal conditions. The limit of detection (LOD) and limit of quantification (LOQ) of (S)-modafinil were 1.25 μg/mL and 2.50 μg/mL, respectively. The established method was also proven to display good selectivity, repeatability, linearity and accuracy. Finally, the method was used to investigate the enantiomeric purity of armodafinil in bulk samples.

Detection of NADH and ethanol at a graphite electrode modified with titania sol-gel/Meldola’s Blue/MWCNT/Nafion nanocomposite film

Abstract For electrocatalytic determination of NADH, a graphite electrode modified with titania sol-gel/Meldola’s Blue/MWCNT/Nafion nanocomposite was proposed. The composition of the matrix film was optimised in terms of the content of carbon nanotubes and Nafion. Incorporation of a redox mediator, Meldola’s Blue, into the nanocomposite film enabled electrocatalytic determination of NADH at a low potential, −50 mV. For determination of ethanol, alcohol dehydrogenase (ADH) was immobilized into the matrix layer. Experimental conditions affecting the biosensor response were examined, including enzyme loading, temperature of measurement and pH of background electrolyte. Assessments of the analytical characteristics of the biosensor were performed with respect to sensitivity, limit of detection, operational stability, repeatability and reproducibility. The proposed biosensor showed electrocatalytic activity toward oxidation of ethanol with sensitivity of 2.24 µA L mmol−1, linear range from 0.05 to 1.1 mmol L−1, and limit of detection of 25 µmol L−1. The apparent Michaelis-Menten constant was 1.24 mmol L−1, indicating a high biological affinity of ADH/titania sol-gel/Meldola’s Blue/MWCNT/Nafion electrode for ethanol. The developed biosensor was tested in determinations of ethanol content in alcoholic beverages.

Colloid particle and protein deposition — Electrokinetic studies

Recent developments in the electrokinetic determination of particle, polyelectrolyte and protein deposition at solid/electrolyte interfaces, are reviewed. In the first section basic theoretical results are discussed enabling a quantitative interpretation of the streaming current/potential and microelectrophoretic measurements. Experimental results are presented, pertinent to electrokinetic characteristics of simple (homogeneous) surfaces such as mica, silica and various polymeric surfaces used in protein studies. The influence of the ionic strength, background electrolyte composition and pH is discussed, and the effective (electrokientic) charge of these interfaces is evaluated. In the next section, experimental data obtained by streaming potential measurements for colloid particle mono- and bilayers are presented and interpreted successfully in terms of available theoretical approaches. These results, obtained for model systems of monodisperse colloid particles are used as reference data for discussion of more complicated experiments performed for polyelectrolyte and protein covered surfaces. Results are discussed, obtained for cationic polyelectrolytes (PEI, PAH) and fibrinogen adsorbing on mica, interpreted quantitatively in terms of the theoretical approach postulating a heterogeneous 3D charge distribution. The Gouy–Chapman model, based on the continuous charge distribution proved inadequate. Interesting experimental data are also discussed, obtained by electrophoretic methods in the case of protein adsorption on colloid latex particles. In the last section, supplementary results on particle deposition on heterogeneous surfaces produced by controlled protein adsorption are discussed. Quantitative relationships between the amount of adsorbed protein, zeta potential of the interface and the particle coverage are specified. Possibility of evaluating the heterogeneity of protein charge distribution is pointed out. The anomalous deposition of colloid particles on protein molecules bearing the same sign of zeta potential, which contradicts classical DLVO theory, is interpreted in terms of the fluctuation theory. It is concluded that theoretical and experimental results obtained for model colloid systems and flat interfaces can be effectively used for interpretation of protein adsorption phenomena, studied by electrophoresis. In this way the universality of electrokinetic phenomena is underlined.

Development and validation of a capillary electrophoresis method for the enantiomeric purity determination of RS86017 using experimental design

A selective capillary electrophoresis method for determination of enantiomeric purity of RS86017, a new antiarrhythmic agent with two chiral centers, was developed and validated using sulfobutyl ether-β-cyclodextrin as chiral selector. The concentration of the chiral selector and organic modifier, pH of background electrolyte (BGE), capillary temperature, and applied voltage were systematically optimized by using orthogonal design and concentration of chiral selector was further optimized. The optimal conditions included 25 mM phosphate buffer at pH 8.0, containing 28 mg/mL sulfobutyl ether-β-cyclodextrin and 20% acetonitrile as running buffer, an applied voltage of 22 kV, and a temperature of 20 °C. The detection wavelength was 206 nm. The obtained method was capable of separating RS86017 from its potential chiral impurities, the S,R-enantiomer, the R,R-diastereomer and the S,S-diastereomer with a short analysis time of 10 min. The separation was validated with respect to its selectivity, repeatability, linearity, precision, accuracy, limits of detection (LOD), limits of quantitation (LOQ) and robustness testing. The LODs and LOQs were 0.8 μg/mL and 2.5 μg/mL for all isomers of RS86017, respectively. Finally, the method was used to investigate the chiral purity of RS86017 in bulk samples.

Improvement of reproducibility and sensitivity of CE analysis by using the capillary coated dynamically with carboxymethyl chitosan

Analysis reproducibility and detection sensitivity of capillary electrophoresis (CE) are often questioned by applied scientists, which has hindered its application as a routine method. To address these issues, a simple, precise, and reproducible dynamic coating method was developed by applying carboxymethyl chitosan (CMC) dynamic coating on fused silica capillary. The proposed coating was accomplished by simply rinsing the capillary with CMC solution for 1 min in between runs, with no regeneration procedure or buffer additives needed. Electroosmotic flow could be well controlled by adjusting the pH of background electrolyte, and the adsorption of analytes onto the capillary inner wall was effectively eliminated. The main parameters of the coating condition were optimized, and extensive applications of these CMC-dynamically coated capillaries in CE separations were then firmly confirmed. By using proteins, aristolochic acids, and inorganic anions as model analytes, the coating showed a good stability, high reproducibility, as well as improved sensitivity. Baseline separations could be obtained with high efficiency. The reduced adsorption was impressively effective for basic proteins, with an average plate number of 90,000/m for each protein, apart from the good resolution on the chromatogram. A high sensitive detection of α-lactalbumin was achieved with a limit of detection (S/N = 3) of 3.5 nM, and the number of theoretical plates was as high as 1,200,000/m. In addition, the combination of the CMC coating with nonaqueous CE and CE-mass spectrometry proved to be practical. All results showed that the CMC-dynamically coated capillary has special properties and obvious superiority over the uncoated ones for CE analysis.

Analysis of flavonoids by capillary zone electrophoresis with electrokinetic supercharging

On-line concentration via Electrokinetic Supercharging (EKS) was used to enhance the sensitivity of the capillary electrophoretic separation of the four flavonoids naringenin, hesperetin, naringin and hesperidin. Separation conditions, including the background electrolyte pH and concentration, the length and choice of terminator and the electrokinetic injection time were optimized. The optimum conditions were: a background electrolyte of 30 mM sodium tetraborate (pH 9.5) containing 5% (v/v) of methanol, electrokinetic injection of the sample (130 s, -10 kV) followed by hydrodynamic injecting of 100 mM 2-(cyclohexylamino)ethanesulfonic acid (CHES) (17 s, 0.5 psi) as terminator, and separation with -20 kV. Under these conditions the four flavonoids could be separated with a sample-to-sample time of 15 min and detection limits from 2.0 to 6.8 ng mL(-1). When compared to a conventional hydrodynamic injection the sensitivity was enhanced between 824 and 1515 times which is 7.6-16 times higher than other CE methods for the on-line concentration of flavonoids. The applicability of the developed method was demonstrated by the detection of the four flavonoids in an aqueous extract of Clematis hexapetala pall.

Development and application of a rapid and efficient CZE method coupled with correction factors for determination of monosaccharide composition of acidic hetero‐polysaccharides from Ephedra sinica

Ephedrine alkaloids cannot account for all the effects of Ephedra sinica and the polysaccharides are also demonstrated to be one of the main bioactive constituents of E. sinica. However, no work has been reported on the analysis of monosaccharide composition of purified polysaccharides isolated from the stem of E. sinica. To develop a rapid and efficient capillary zone electrophoresis (CZE) method based on pre-column derivatisation with 1-phenyl-3-methyl-5-pyrazolone for the simultaneous determination of neutral and acidic sugars of purified polysaccharides from E. sinica. Three polysaccharides (ESP-A3, ESP-A4 and ESP-B4) were isolated and purified by ion exchange and gel-filtration chromatography from the stem of E. sinica. The effects of background electrolyte pH and concentration, applied voltage and temperature on the separation were investigated. Meanwhile, factors affecting the hydrolysis of ESP-B4 with sulphuric acid were investigated by changing the hydrolysis time, acid concentration and hydrolytic temperature to achieve complete hydrolysis. The standard curves coupled with correction factors were used to calculate molar ratios. The optimal CZE method coupled with correction factors was successfully applied to the determination of molar ratios of three purified polysaccharides and their corresponding partial acid hydrolysis products. ESP-A3, ESP-A4 and ESP-B4 were all typical acidic hetero-polysaccharides and consisted of xylose, arabinose, glucose, rhamnose, mannose, galactose, glucuronic acid and galacturonic acid, and their corresponding molar ratios were 6.8:7.5:1.0:14.0:13.7:22.3:10.2:3.8 for ESP-A3, 1.2:4.1:1.0:5.1:1.6:17.3:3.1:2.2 for ESP-A4, and 1.0:4.5:1.0:2.0:1.0:5.5:1.5:50.0 for ESP-B4. The results provided scientific evidence for the further study of the structure and bioactivity of complex acidic E. sinica polysaccharides.

Separation of cis-β-lactam enantiomers by capillary electrophoresis using cyclodextrin derivatives

Chiral separation of 19 pairs of cis-β-lactam (BL) stereoisomers of pharmacological importance was examined by capillary electrophoresis using cyclodextrin (CD) derivatives. In order to select the most effective conditions separating the highest number of stereoisomers of BLs, single carboxymethyl α-, β- and γ-, as well as sulfobutyl β-CD derivatives were applied. Additionally, carboxymethyl and sulfobutyl β-CD derivatives complemented with neutral β-CD derivatives as dual CD systems were tested. Both the composition and concentration of applied selectors and the pH of background electrolyte were selected. In single systems the structural characteristics of BLs and the complex forming affinity were correlated. Most BLs provided optimal complexation with β-CD derivatives. In conclusion, the efficiency of combining sulfobutyl-β-CD and permethylated β-CD was superior to other single and dual CD systems applied. This method successfully separated each pair of stereoisomers investigated.

Reactive Diffusion of Uranium in Compacted Clay: Evaluation of Diffusion Coefficients by a Kinetic Approach

The effect of compaction of bentonite on the diffusion behavior of uranium was studied for the safety assessment of radioactive waste (storage and disposal practices). Since the permeability of the compacted clay is very low, the main mechanism for radionuclide transport is governed by the diffusion phenomenon. The diffusion process of uranium in compacted clay as a porous medium has been modeled by Fick's second law taking into account the effect of sorption and considering the non-steady state. The diffusion coefficients and profiles concentration values were calculated by a computational method using a numerical program based on the Newton-Raphson algorithm. In this simulation, the experimental values were used to determine the uranium concentration profiles versus depth of the clay pellet. It was concluded that the dry density of the compacted clay and the aqueous solution properties (pH and ionic strength of background electrolyte) played an important role in the uranium transport through compacted clays.

Polymeric ionic liquid as additive for the high speed and efficient separation of aromatic acids by co-electroosmotic capillary electrophoresis

A simple and reliable co-electroosmotic capillary electrophoresis system for the fast determination of aromatic acids has been developed by employing poly (1-vinyl-3-butylimidazolium bromide) as the background electrolyte modifier. The polymeric ionic liquid was synthesized by the conventional radical polymerization. The reversed electroosmotic flow was obtained by adding a small amount of the polymeric ionic liquid (0.0006%, w/v) to the electrolyte. To further improve the resolution of aromatic acids, conditions including the concentration of polymeric ionic liquid and pH of background electrolytes were optimized. All eight aromatic acids were baseline resolved in one measurement in a short time (less than 3.5 min) under optimized conditions, 100 mM NaH 2PO 4 buffer containing 0.006% (w/v) polymeric ionic liquid, pH 6.0. Separation efficiencies were in the range from 355,000 to 943,000 (plates/m). Satisfactory reproducibility on the basis of the migration time of analytes was achieved. RSDs ( n = 3) were less than 0.33% except the p-aminobenzoic acid (0.9%). The applicability of the present method has been demonstrated for the determination of water-soluble aromatic acids in a common drug for external use.

Separation and Determination of Amino Acids by CE Using 1-Butyl-3-methylimidazolium-Based Ionic Liquid as Background Electrolyte

Capillary electrophoresis using 1-butyl-3-methylimidazolium tetrafluoroborate as background electrolyte for the separation and determination of 11 amino acids was studied. Several parameters, such as ionic liquid concentration, pH of background electrolyte and applied voltage, were optimized. Amino acids were derived with Sanger’s reagent (2,4-dinitrofluorobenzene) and the detection was performed by an ultraviolet absorption detector at 360 nm. Under selected conditions, 11 amino acids were completely separated within 16 min. The RSD values of integrated areas and migration times are <3.03 and <1.64%, respectively. The electroosmotic flow can be influenced by imidazolium cation, and the association between the imidazolium cation and the derived amino acids plays an important role in the separation mechanism. This method not only provides an approach for the separation and determination of amino acids, but is also an extension of the ionic liquid application to capillary electrophoresis.

Prediction of electrophoretic enantioseparation of aromatic amino acids/esters through MIA-QSPR

Multivariate image analysis (MIA) descriptors have been applied to predict the enantiomer migration orders of a series of aromatic amino acids and aromatic amino esters. In MIA-QSPR, pixels of chemical structures (2D images) stand for descriptors, and structural changes account for the variance in relative migration times (RMTs). R and S enantiomers were differentiated by drawing up or down stereo bonds at the chiral carbon, and the RMT predictions of the title compounds in specific medium (20 mM Tris–citric acid background electrolyte (pH 2.50) containing 5.0 mM of (+)-18-crown-6-tetracarboxylic acid) were reliably obtained ( r 2 = 0.992, q LOO - CV 2 = 0.926 , and q L - 20 % - O - CV 2 = 0.910 ) after removing two outliers from the dataset. MIA descriptors were capable to recognize the physicochemical information and may be useful to predict enantiomer migration orders of amino acids and amino esters whose pure enantiomers are unavailable.

Validated Assay for the Determination of Mitoxantrone in Pharmaceuticals Using Capillary Zone Electrophoresis

The first capillary zone electrophoretic (CZE) method for the determination of mitoxantrone (MTX) in pharmaceutical formulations was developed. The influence of background electrolyte (BGE) species, pH, concentration (c BGE), organic modifier, capillary temperature, applied voltage, and injection time was investigated. Optimum results were achieved with 25 mM ammonium acetate at an apparent pH value of 5.0 in 50% v/v acetonitrile, applied voltage of +30 kV, and capillary temperature of 25°C. The samples were introduced into the capillary hydrodynamically for 2 s at 33.5 mbar. Mitoxantrone was detected at a wavelength of 242 nm. Mitoxantrone and doxorubicin (DOX) (used as internal standard, ISTD) were completely separated in less than 7 min. The method was suitably validated with respect to linearity, limits of detection (LOD) and quantification (LOQ), accuracy, precision, selectivity, and robustness. The proposed method was applied successfully for the determination of MTX in its injectable pharmaceutical formulation.

Multidimensional Separation of Chiral Amino Acid Mixtures in a Multilayered Three-Dimensional Hybrid Microfluidic/Nanofluidic Device

Microscale total analysis systems (microTAS) allow high-throughput analyses by integrating multiple processes, parallelization, and automation. Here we combine unit operations of microTAS to create a device that can perform multidimensional separations using a three-dimensional hybrid microfluidic/nanofluidic device composed of alternating layers of patterned poly(methyl methacrylate) and nanocapillary array membranes constructed from nuclear track-etched polycarbonate. Two consecutive electrophoretic separations are performed, the first being an achiral separation followed by a chiral separation of a selected analyte band. Separation conditions are optimized for a racemic mixture of fluorescein-isothiocyanate-labeled amino acids, serine and aspartic acid, chosen because there are endogenous D-forms of these amino acids in animals. The chiral separation is implemented using micellar electrokinetic chromatography using beta-cyclodextrin as the chiral selector and sodium taurocholate as the micelle-forming agent. Analyte separation is monitored by dual-beam laser-induced fluorescence detection. After separation in the first electrophoretic channel, the preselected analyte is sampled by the second-stage separation using an automated collection sequence with a zero-crossing algorithm. The controlled fluidic environment inherent to the three-dimensional architecture enables a series of separations in varying fluidic environments and allows sample stacking via different background electrolyte pH conditions. The ability to interface sequential separations, selected analyte capture, and other fluidic manipulations in the third dimension significantly improves the functionality of multilayer microfluidic devices.