Atomic Force Microscopy Analysis Research Articles

Extraction and characterization of microcrystalline cellulose from Vachellia nilotica plant leaves: A biomass waste to wealth approach.

Biobased waste utilization is an intriguing area of research and an ecologically conscious approach. Plant-based materials can be used to render cellulose, which is an eco-friendly material that can be used in numerous aspects. In the current investigation, cellulose was extracted from the leaves of the Vachellia nilotica plant via acid hydrolysis. The application of this research is specifically directed toward the utilization of undesirable plant sources. To validate the extracted cellulose, FT-IR spectroscopy was applied. The cellulose was measured to have a density of 1.234 g/cm3. The crystallinity index (58.93%) and crystallinity size (11.56 nm) of cellulose are evaluated using X-ray diffraction spectroscopy analysis. The highest degradation temperature (320.8°C) was observed using thermogravimetry and differential scanning calorimetry curve analysis. The analysis of particle size was conducted utilizing images captured by scanning electron microscopy. Particle size of less than 30 μm was found and they exhibit non-uniform orientation. Additionally, atomic force microscopy analysis shows an improved average surface roughness (Ra), which increases the possibility of using extracted cellulose as reinforcement in biofilms.

Influence of Stacking Order on the Structural and Optical Properties of Cu2ZnSnS4 Absorber Layer Prepared from DC-Sputtered Oxygenated Precursors

Several studies have attempted to overcome the sudden volume expansion of the precursor during sulfurization by the use of oxygen-containing precursors when growing the CZTS absorber. This work demonstrates the influence of precursor stacking orders on the properties of the CZTS thin film absorber layer from DC-sputtered oxygenated precursors for solar cell applications. CZTS absorber layers were prepared from three types of DC-sputtered stacks, namely, Zn-O/Sn/Cu, Sn/Zn-O/Cu, and Sn/Cu/Zn-O. The precursors were sequentially deposited on a soda lime glass (SLG) using DC-magnetron sputtering and annealed in a sulfur and nitrogen ambient. X-ray diffractometry (XRD) and Raman spectroscopy analyses reveal the formation of crystalline kesterite CZTS structure regardless of the precursor stacking order. Atomic force microscope (AFM) analysis showed that CZTS thin films grown from precursor stacks SLG/Zn-O/Sn/Cu and SLG/Sn/Zn-O/Cu had improved morphological properties with densely packed large grains compared to that with stack SLG/Sn/Cu/Zn-O. SLG/Zn-O/Sn/Cu is the best stack among the studied stacking orders since it exhibits large grains in the absorber layer, which is preferential for high-efficiency thin film solar cells. The use of oxygenated precursor with order Sn/Zn-O/Cu promises improved CZTS absorber properties as it exhibits better morphological properties.

High Potential Electrochemical Synthesis of Thermally Reduced Graphene Nanomaterial

In this study, we provide electrochemical techniques for synthesizing thermally reduced graphene nanomaterial that have high potential, low defects, cost-effectiveness, and ecological sustainability. The electrochemical exfoliation is carried out by employing a 195 W DC (voltage = 60[Formula: see text]V and current = 3.25 A) power source at a maximum electrolyte temperature of about 92.5∘C within the aqueous suspension of 2[Formula: see text]M of sulfuric acid (H2[Formula: see text]. Thereafter, the synthesized nanomaterial was treated in the weak piranha [combination of sulfuric acid and hydrogen peroxide (H2[Formula: see text]] solution using an electrochemical technique inside the water bath sonicator at 80∘C. X-ray diffraction (XRD) analysis shows the peak of diffraction to the (002) plane of the reduced graphene oxide (RGO) samples emerges at around 2[Formula: see text] and 26.56∘ with an interplanar distance of 3.40 Å and 3.54 Å. According to the XRD data, after the high-temperature thermal reduction phase, the structure of the crystals and interplanar separation were recovered. The size of the crystallite of RGO produced under H2SO4 conditions was discovered to be greater than the crystallite size of graphene oxide produced under piranha solution conditions. The Raman analysis results show that the degree of disorder of the graphene synthesized within the H2O2 was higher than in comparison to the graphene synthesized in H2SO4. Field emission scanning electron microscopy (FE-SEM) results show that graphene synthesized in the presence of H2O2 has a thin and porous microstructure in comparison to H2SO4 with no significant effect on the presence of the availability of the C/O ratio. The atomic force microscopy (AFM) analysis indicates that the surface roughness of the graphene synthesized in the H2O2 was higher than that of the H2SO4. The Fourier transform infrared spectroscopy (FT-IR spectroscopy) analytical results show that the majority of the functional groups have been eliminated within the samples.

UV-mediated photochemical synthesis and investigation of the antiviral properties of Silver nanoparticle-polyvinyl butyral nanocomposite coatings as a novel antiviral material with high stability and activity

Effectively developing new antimicrobial surfaces for viral diseases requires considerable research, money, and time. Moreover, new species of microorganisms and pathogens are constantly appearing or entering from other regions, which can cause epidemics or pandemics. The ongoing presence of SARS-CoV-2 underscores the need to develop new antimicrobial materials. In this context, a novel UV-irradiated photochemical in-situ synthesis method is introduced for producing durable, long-lasting antiviral silver-polymer (AgNP-PVB) nanocomposite coatings. These coatings are intended to mitigate infectious disease transmission across various frequently touched surfaces, such as door handles, keypads, bank encoders, telephone locks, lift buttons, etc. Additionally, the significance of the size and concentration of AgNP in influencing the physical and antiviral properties of these nanocomposite coatings is illustrated. Detailed studies of AgNP-PVB coatings were conducted using X-ray diffraction, Raman spectroscopy, atomic force microscopy (AFM), and ultraviolet-visible-near-infrared spectroscopy, and contact angle measurements. The antiviral properties of the coatings were evaluated by a one-step reverse transcription real-time polymerase chain reaction (one-step qRT‒PCR) using synthetic SARS-CoV-2 RNA. Raman spectra signatures confirm AgNPs in the PVB matrix by matching identified peaks in X-ray diffractograms. AFM analysis revealed a reduction in AgNP size in the nanocomposite with an increase in the irradiation duration from 5 to 30 min. Spectroscopic results corresponding to AFM measurements highlighted specific wavelengths related to different AgNP size ranges. Contact angle measurements suggest that antiviral activity can be predicted by calculating the surface free energy (SFE) of the sample. As the SFE value increases, antiviral activity decreases. Nanocomposite coatings (with concentrations of 150, 200, 500, and 1000 ppm AgNP) are effective in reducing the activity of SARS-CoV-2, indicating their potential as long-acting preventive agents against viral infections. A methodology incorporating a specialized algorithm was devised for the application of the investigated coatings, which also integrates 3D scanning and printing techniques for fabricating complex geometry flexible protective cover. Subsequently, this coating was applied to produce a protective cover for the widely utilized public object, the door handle, employing 3D printing technology. As a result of the work, a long-term, durable antiviral AgNP-PVB nanocomposite coating with varying AgNP sizes (ranging from 15 to 118 nm) and concentrations (150, 200, 500, and 1000 ppm) was successfully developed.

Assessment of sealing efficacy, radiopacity, and surface topography of a bioinspired polymer for perforation repair.

Root perforation repair presents a significant challenge in dentistry due to inherent limitations of existing materials. This study explored the potential of a novel polydopamine-based composite as a root repair material by evaluating its sealing efficacy, radiopacity, and surface topography. Confocal microscopy assessed sealing ability, comparing the polydopamine-based composite to the gold standard, mineral trioxide aggregate (MTA). Radiopacity was evaluated using the aluminium step wedge technique conforming to ISO standards. Surface roughness analysis utilized atomic force microscopy (AFM), while field emission scanning electron microscopy (FESEM) visualized morphology. The polydopamine-based composite exhibited significantly superior sealing efficacy compared to MTA (P < 0.001). Radiopacity reached 3 mm aluminium equivalent, exceeding minimum clinical requirements. AFM analysis revealed a smooth surface topography, and FESEM confirmed successful composite synthesis. This study demonstrates promising properties of the polydopamine-based composite for root perforation repair, including superior sealing efficacy, clinically relevant radiopacity, and smooth surface topography. Further investigation is warranted to assess its clinical viability and potential translation to endodontic practice.

Development of VEGF mimetic QK peptide on polycaprolactone nanofiber for vascular tissue engineering

Electrospinning allows promoting vascular tissue formation. Polycaprolactone (PCL) is a promising polymer for vascular tissue engineering because of its great mechanical strength and efficient fabrication. However, PCL shows limited biocompatibility owing to its hydrophobic structure. PCL nanofibers can be modified by peptides to improve biological activity. KLTWQELYQLKYKGI (QK) is a peptide that mimics the Vascular Endothelial Growth Factor (VEGF) by organizing endothelial cells. It is critically important to identify the optimum concentration of QK peptide conjugation onto PCL nanofiber for vascularization. Thus, PCL nanofibers were conjugated by different QK peptide concentrations (10 µM, 100 µM and 1000 µM). QK conjugated nanofibers were characterized by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM) analysis. The vascularization was evaluated by Live and Dead staining assay, real time PCR of platelet/endothelial cell adhesion molecule (PECAM-1), VEGF and vascular endothelial-cadherin (VE-cadherin) genes and VEGF immunofluorescence analysis. The surfaces of PCL nanofibers were modified by different concentrations of QK peptide. The roughness of nanofibers increased depending on the increased concentration of QK peptide. The higher cell attachment and cell viability were observed in 1000 µM of QK peptide. 1000 µM of QK peptide showed higher vasculogenic potential in terms of PECAM, VEGF, and VE-cadherin gene expression than all the other experimental groups. In the same on gene expression analysis by qPCR, 1000 µM concentration of QK peptide showed the higher VEGF protein than the other experimental groups. 1000 µM concentration of QK peptide can be used to improve the vasculogenic property of PCL nanofibers.

Enhancing CFRP laminates with plasma jet arrays: A study of interlaminar mechanical properties

AbstractThis study delves into the efficacy of plasma jet array treatment in bolstering the interlaminar toughness of Carbon Fiber Reinforced Polymer (CFRP) prepregs, a crucial parameter for their deployment in high‐performance domains. Employing high‐frequency pulsed microsecond plasma jet arrays for surface modification, this research not only demonstrated a 19.49% upsurge in peak load capacity but also a remarkable 29.94% enhancement in Mode I interlaminar fracture toughness, as evident from Double Cantilever Beam (DCB) tests. Furthermore, the surface wettability improvements were underscored by a substantial decrease in water contact angle from 108.33° to 31.45° and a total surface energy augmentation from 12.20 to 64.16 mN/m, post a 1‐min plasma treatment. X‐ray Photoelectron Spectroscopy (XPS) results indicated an appreciable rise in oxygen functionalities, suggesting enhanced resin‐fiber bonding. Additionally, Atomic Force Microscopy (AFM) and Scanning Electron Microscopy (SEM) analyses revealed notable decreases in surface roughness and microscale defects, contributing to smoother surfaces conducive to better adhesive bonding and reduced manufacturing defects. These multifaceted improvements, stemming from alterations in surface chemistry and topography, underpin the significant potential of plasma treatment in advancing CFRP laminate applications requiring superior durability and mechanical resilience.Highlights A plasma jet arrays method to enhance CFRP's interlaminar properties was studied. The influence mechanism of plasma modification was revealed in detail. The interlayer toughening mechanism of CFRP after plasma modification is proposed.

Fundamental Origin of Si Surface Defects Caused by Laser Irradiation and Prevention of Suboxide Formation through High Density Ultrathin SiO2

This research investigates surface damage in electronic devices from laser irradiation, particularly focusing on voids, cracks, and vacancies. We discovered that applying a high-density ultrathin SiO2 layer effectively prevents such defects. Atomic Force Microscopy (AFM) analysis showed a significant reduction in surface roughness, with the Rq factor value dropping to 0.158 nm in samples coated with this SiO2 layer. Additionally, X-ray Photoelectron Spectroscopy (XPS) was used to study suboxide formation in the Al2O3/Si structure, revealing insights into defect origins. Electrical tests indicated a substantial decrease in laser-induced damage, evidenced by a leakage current density reduction to 2.4 × 10−6 A/cm2, markedly lower than uncoated samples. Post-metallization annealing (PMA) further improved results, with the interface state density decreasing to 0.63 × 1012 atoms eV−1 cm−2. Our findings highlight the effectiveness of the high-density ultrathin SiO2 layer in mitigating surface defects caused by continuous wave (CW) laser irradiation, promising significant advancements in electronic device manufacturing through potential application in CW laser annealing processes.

Correlating macroscopic plant growth parameters to nanomechanical properties of cellulose microfibrils

The plant cell wall, a vital component in providing structural integrity and facilitating growth, comprises cellulose microfibrils among its major constituents. This study employed Atomic Force Microscopy (AFM) to investigate the intricate relationship between genetic mutation, cellulose microfibril organization, nanomechanical properties of cellulose microfibrils and plant growth. Focusing on the Arabidopsis thaliana wild type (WT) and ixr1–2 mutant population (known for resistance to herbicide ISOXABEN), we utilized AFM to scrutinize cellulose microfibrils on the newly synthesized cell wall in 5-day-old dark-grown hypocotyls. Our macroscopic analysis revealed significant differences in plant growth, prompting a detailed examination at the nanoscale using AFM to discover if the macroscopic disparity between these two populations gets translated in structural details, orientation, and mechanical properties of cellulose microfibrils at the nanoscale too. AFM analysis highlighted distinct organizational disparities in cellulose microfibrils between the WT and mutant population. Our results revealed that the WT manifests a more aligned and oriented microfibril structure in contrast to the mutant population that shows significantly less aligned cellulose microfibrils in the plant growth direction. Also, the WT and mutant population demonstrate nuanced differences in height, width, roughness, deformation, and stiffness. The observed nanoscale alterations in microfibril structure and nano-mechanical properties contribute to an improved understanding of the intricate dynamics governing plant cell wall structure and its pivotal role in growth and development.

Modeling Nonlinear Dynamics of Functionalization Layers: Enhancing Gas Sensor Sensitivity for Piezoelectrically Driven Microcantilever.

This article presents a parametrized response model that enhances the limit of detection (LOD) of piezoelectrically driven microcantilever (PD-MC) based gas sensors by accounting for the adsorption-induced variations in elastic properties of the functionalization layer (binder) and the nonlinear motional dynamics of the PD-MC. The developed model is demonstrated for quantifying cadaverine, a volatile biogenic diamine whose concentration is used to assess the freshness of meat. At low concentrations of cadaverine, an increase in the resonance frequency is observed, contrary to the expected reduction due to mass added by adsorption. The study explores the variations in the elastic modulus vis-à-vis the adsorbed mass of cadaverine and derives the resonance frequency to the adsorbed mass response function. We advance a blended technique involving the analysis of atomic force microscopy (AFM) force-distance (f-d) curves and fitting of the quartz crystal microbalance (QCM) impedance response spectrum to deduce the adsorption-induced changes in the viscoelastic properties of the functionalization layer. The findings obtained are subsequently employed in modeling the response function for a structurally nonhomogenous PD-MC, highlighting the significance of the functionalization layer to the global elastic properties. The structural composition of the PD-MC beam adopted herein features a trapezoidal base hosting the actuating piezoelectric stratum and a rectangular free end with a functionalization layer. The Euler-Bernoulli beam theory coupled with Hamilton's principle is used to develop the equation of motion, which is subsequently discretized into a set of nonlinear ordinary differential equations via Galerkin expansion, and the solutions to the first fundamental mode of vibration are determined using the method of multiple scales. The obtained solutions provide a basis for deducing the nonlinear response function model to the adsorbed mass. The derived model is validated by recorded resonance frequency changes resulting from exposure to known concentrations of cadaverine. We demonstrate that the increase in resonance frequency for low concentrations of cadaverine is due to the dominance of the variation of the elastic modulus of the functionalization layer originating from the initial binder-analyte interactions over damping due to added mass. It is concluded that the developed nonlinear response function model can reliably be used to quantify the cadaverine concentration at low concentrations with an elevated Limit of Detection.

Effect of In-Situ H Doping on the Electrical Properties of In2O3 Thin-Film Transistors

In this article, this research demonstrates the influence of in-situ introduction of H2 into the working gas on the physical properties of post-annealed In2O3 thin films and the performance of associated devices. A gradual increase in the H2 ratio leads to improved film quality, as indicated by spectroscopic ellipsometry, X-ray photoelectron spectroscopy, and atomic force microscope analyses showing a reduction in defect states such as band-tail states and VO in the film, and a smoother surface morphology with the root mean square roughness approximately 0.446 nm. Furthermore, this hydrogen doping effect results in a distinct shift in the device’s threshold voltage toward the positive direction, and an improvement in the field-effect mobility and subthreshold swing. Consequently, a high-performance In2O3:H TFT is developed, exhibiting a field-effect mobility of 47.8 cm2/Vs, threshold voltage of −4.1 V and subthreshold swing of 0.25 V/dec. These findings highlight the potential of in-situ H doping as a promising approach to regulate In2O3-based TFTs.

Facile Preparation of Gold Nanoparticles Silica Composite Film Embedded in Anodized Aluminium Oxide-Glass Substrate

Thin film based on gold nanoparticles or AuNPs is typically used as catalyst in the industrial processes due to their high stability and good reusability. In this work, a thin AuNPs-silica composite film was fabricated firstly from sol-gel method by mixing gold pyrazolate complex to a medium comprised of ethanol, deionized water, and hydrochloric acid followed by addition of tetrabutyl orthosilicate as silica source. Next, 70 microliters of the sol-gel solution were spin-coated on several type of substrates such as glass, anodized aluminium oxide or AAO, and combination of both to yield gold complex-silica composite film. It was found that gold complex-silica composite film fabricated on combination of both AAO-glass substrate gave the best quality based on its surface thickness, layer uniformity and film brittleness. Later, the film was selected and subjected to thermal hydrogen reduction at 210 degrees Celsius for 2 hours to facilitate the formation of gold nanoparticles to give AuNPs-silica in AAO-glass film. Before the heat treatment, the light-brownish colour of the original gold complex-silica in AAO-glass film in daylight will appear as a pinkish red film under UV light, suggesting the interaction between gold atoms and supported by its luminescence spectrum at 692 nm. Upon heat treatment, the resulting AuNPs-silica in AAO-glass film gave a deep-red colour indicating the successful formation of AuNPs. The presence of AuNPs in the film was further confirmed based on the absorption peak at 545 nm, X-ray diffraction pattern at 38.20 degrees for d111 plane in wide-angle region, transmission electron microscopy images showing a small and sphere shape particles as well as its elemental composition in energy dispersive X-ray analysis. Moreover, scanning electron microscope images also suggested that the AAO pores is fully filled with the composite and is in accordance with its surface roughness study via atomic force microscopy analysis.

ZnO nanoparticles induced biofilm formation in Klebsiella pneumoniae and Staphylococcus aureus at sub-inhibitory concentrations.

Biofilm formation by the pathogenic bacteria generates a serious threat to the public health as it can increase the virulence potential, resistance to drugs, and escape from the host immune response mechanisms. Among the environmental factors that influence thebiofilm formation, there are only limited reports available on the role of antimicrobial agents. During the antimicrobial drug administration or application for any purpose, the microbial population can expect to get exposed to the sub-minimum inhibitory concentration (sub-MIC) of the drug which will have an unprecedented impact on microbial responses. Hence, the study has been conducted to investigate the effects of sub-MIC levels of zinc oxide nanoparticles (ZnO NPs) on the biofilm formation of Klebsiella pneumoniae and Staphylococcus aureus. Here, the selected bacteria were primarily screened for thebiofilm formation by using the Congo red agar method, and their susceptibility to ZnO NPs was also evaluated. Quantitative difference in biofilm formation by the selected organisms in the presence of ZnO NPs at the sub-MIC level was further carried out by using the microtiter plate-crystal violet assay. Further, the samples were subjected to atomic force microscopy (AFM) analysis to evaluate the properties and pattern of thebiofilm modulated under the experimental conditions used. From these, the organisms treated with sub-MIC levels of ZnO NPs were found to have enhanced biofilm formation when compared with the untreated sample. Also, no microbial growth could be observed for the samples treated with the minimum inhibitory concentration (MIC) of ZnO NPs. The results observed in the study provide key insights into the impact of nanomaterials on clinically important microorganisms which demands critical thinking on the antimicrobial use of nanomaterials.

Disulfiram Reduces Atherosclerosis and Enhances Efferocytosis, Autophagy, and Atheroprotective Gut Microbiota in Hyperlipidemic Mice.

Pyroptosis executor GsdmD (gasdermin D) promotes atherosclerosis in mice and humans. Disulfiram was recently shown to potently inhibit GsdmD, but the invivo efficacy and mechanism of disulfiram's antiatherosclerotic activity is yet to be explored. We used human/mouse macrophages, endothelial cells, and smooth muscle cells and a hyperlipidemic mouse model of atherosclerosis to determine disulfiram antiatherosclerotic efficacy and mechanism. The effects of disulfiram on several atheroprotective pathways such as autophagy, efferocytosis, phagocytosis, and gut microbiota were determined. Atomic force microscopy was used to determine the effects of disulfiram on the biophysical properties of the plasma membrane of macrophages. Disulfiram-fed hyperlipidemic apolipoprotein E-/- mice showed significantly reduced interleukin-1β release upon invivo Nlrp3 (NLR family pyrin domain containing 3) inflammasome activation. Disulfiram-fed mice showed smaller atherosclerotic lesions (~27% and 29% reduction in males and females, respectively) and necrotic core areas (~50% and 46% reduction in males and females, respectively). Disulfiram induced autophagy in macrophages, smooth muscle cells, endothelial cells, hepatocytes/liver, and atherosclerotic plaques. Disulfiram modulated other atheroprotective pathways (eg,efferocytosis, phagocytosis) and gut microbiota. Disulfiram-treated macrophages showed enhanced phagocytosis/efferocytosis, with the mechanism being a marked increase in cell-surface expression of efferocytic receptor MerTK. Atomic force microscopy analysis revealed altered biophysical properties of disulfiram-treated macrophages, showing increased order-state of plasma membrane and increased adhesion strength. Furthermore, 16sRNA sequencing of disulfiram-fed hyperlipidemic mice showed highly significant enrichment in atheroprotective gut microbiota Akkermansia and a reduction in atherogenic Romboutsia species. Taken together, our data show that disulfiram can simultaneously modulate several atheroprotective pathways in a GsdmD-dependent as well as GsdmD-independent manner.

Tailoring of charge carriers with deposition temperature in pulsed laser deposited BiFeO3 thin films

This research investigates the structural, topological, electrical and optical properties of pulsed laser deposited polycrystalline BiFeO3 thin films on silicon and glass substrate at varying deposition temperatures ranging from 400 °C to 700 °C. X-ray diffraction confirm rhombohedral phase and X-ray photoelectron spectroscopy reveals stoichiometric BiFeO3 films. The optical bandgap of thin films obtained from absorption spectra increases with the substrate temperature. Photoluminescence emission spectrum reveals the defects and Atomic Force Microscopy analysis bring out the surface topography and crystallinity improvement with temperature. The charge transport studies reveal a transition in conductivity from n-type at lower deposition temperature to p-type at higher deposition temperature, attributed to oxygen and bismuth vacancies respectively. The intricate understanding of conductivity tuning and the leaky nature of BiFeO3 thin film opens avenues for applications in non-volatile memories, particularly neuromorphic devices.

Atomic force microscopy, deformation-recovery and numerical study of wheat dough

Experimental and numerical modelling work related to microstructure and deformation of starch, gluten and wheat dough was presented. Atomic force microscopy analyses through force spectroscopy on starch samples showed elastic behaviour of both dried and reconstituted wet starch granules, where wet starch was shown to be more cohesive than dried starch. Deformation-recovery test over time under compression mode showed almost complete recovery to original sample height of gluten, whereas only a slight recovery was observed for dough. Finite element modelling was then commenced to simulate gluten deformation-recovery and starch-gluten dough deformation. The gluten geometry used for the starch-gluten dough model was obtained from cryo-SEM image from the previous work before the starch geometry was then included. The interface between the starch and gluten model was defined using viscoelastic cohesive zone elements. The modelling results suggested significant influence of gluten cellular structure towards starch-gluten dough integrity. In addition, the results from the current work further supported the previous report of the starch-gluten interfacial behaviour using viscoelastic cohesive zone model.

NanoLocz: Image Analysis Platform for AFM, High-Speed AFM, and Localization AFM.

Atomic Force Microscopy (AFM), High-Speed AFM (HS-AFM) simulation AFM, and Localization AFM (LAFM) enable the study of molecules and surfaces with increasingly higher spatiotemporal resolution. However, effective and rapid analysis of the images and movies produced by these techniques can be challenging, often requiring the use of multiple image processing software applications and scripts. Here, NanoLocz, an open-source solution that offers advanced analysis capabilities for the AFM community, is presented. Integration and continued development of AFM analysis tools is essential to improve access to data, increase throughput, and open new analysis opportunities. NanoLocz efficiently leverages the rich data AFM has to offer by incorporating and combining existing and newly developed analysis methods for AFM, HS-AFM, simulation AFM, and LAFM seamlessly. It facilitates and streamlines AFM analysis workflows from import of raw data, through to various analysis workflows. Here, the study demonstrates the capabilities of NanoLocz and the new methods it enables including single-molecule LAFM, time-resolved LAFM, and simulation LAFM.

Polyelectrolyte Platforms with Copper Nanoparticles as a Multifunctional System Aimed at Healing Process Support

(1) Purpose: The aim of the study was to develop a nanocomposite with copper nanoparticles constituting a bacteriostatic surface to maintain human lung cell function. (2) Methods: A polyelectrolyte layer coating that incorporated copper nanoparticles was designed. As a bacteriostatic factor, copper nanoparticles were applied as a colloidal solution of copper nanoparticles (ColloidCuNPs) and a solution of copper nanoparticles (CuNPs). The influence of the polyelectrolytes on selected Gram (+) and Gram (−) strains was examined. The function and morphology of the human adenocarcinoma A549 cell line, comprising human epithelial lung cells cultured in the presence of nanocomposite layer coatings, were evaluated. We applied fluorescence and scanning electron microscopies, as well as flow cytometry, for these studies. Furthermore, the layer coating material was characterized by atomic force microscopy (AFM) and energy dispersive X-ray analysis (EDX). (3) Results: It was observed that the polyelectrolytes polyethyleneimine (PEI) and poly-L-lysine (PLL) did not induce proliferation of the E. coli strain. However, they did induce the proliferation of the S. aureus strain. Due to the effectiveness of the CuNPs against the E. coli strain, CuNPs were selected for further research. The designed coatings of proper NPs shared the sustained function of human lung cells within 10 days of culture. The AFM and EDX characterization confirmed the presence of copper in the layer coating nanomaterial. The presence of CuNPs in polyethyleneimine-based nanocomposite deepened the bacteriostatic effect on E. coli compared with PEI alone. Meanwhile, incorporating CuNPs in PLL allowed A549 cell maintenance but did not exert a bacteriostatic influence on the examined strain. (4) Conclusions: The platform based on polyelectrolytes, incorporated with copper nanoparticles, that ensures the growth and appropriate morphology of the human lung epithelial cells, might be considered an element of a system for medical devices used to maintain the function of human lung cells.

Phase Evolution, Dielectric, and Electric Behavior of Sm‐Doped BCTO Ceramic Fabricated by Semi‐Wet Method

AbstractBi(2/3)‐xSmxCu3Ti4O12 (BSCTO x = 0.05, 0.10, and 0.20) ceramics are synthesized using semi‐wet technique and an extensive investigation into their structural, morphological, and elemental properties, alongside dielectric and impedance behaviors, is meticulously carried out. X‐ray powder diffraction analysis unequivocally confirmed the formation of a monophasic BCTO cubic phase without any discernible secondary phases. and the crystallite size of the BSCTO ceramic, obtained by X‐ray diffraction using Debye Scherrer formula, range from 62 to 81 nm. Rietveld analysis reveals that ceramics have a body centered cubic structure with space group Im‐3. The Scanning electron microscope image displays the dense microstructure of the ceramics, while EDX analysis unveils the elemental composition of resulting products. Doping with Sm3+ induced a notable reduction in grain size, as observed through Scanning electron microscope and Atomic Force Microscope analyses, indicating Sm3+ hindered grain growth during sintering, potentially resulting in reduced dielectric constant (ε′). Dielectric constant and dielectric loss of the composition (x = 0.2) are found to be 152 and 0.04, respectively at room temperature (1 kHz). Impedance characteristics revealed a substantial increase in grain boundary resistance, leading to improved dielectric loss. The AC conductivity of BSCTO ceramics exhibited a frequency‐dependent increase satisfying to Johncher's power law.

In Situ Real-Time Atomic Force Microscopy Observations of Chain Mobility at Polymer/Water Interfaces of Poly(methyl methacrylate), Poly(2-hydroxyethyl methacrylate), and Poly(2-methoxyethyl methacrylate) Films in Water.

Polymer materials are widely used in water or in contact with an aqueous environment. However, evaluating the chain mobility, a crucial parameter, at a polymer-water interface is challenging. In this study, we, for the first time, observed poly(methyl methacrylate) (PMMA), poly(2-hydroxyethyl methacrylate) (PHEMA), and poly(2-methoxyethyl methacrylate) (PMEMA) film surfaces in water via in situ real-time atomic force microscopy (AFM) in tapping mode and quantified the chain mobility. The average displacement between adjacent images (nm/8.75 min) was evaluated using particle image velocimetry. The displacement of PMMA, which has a high bulk glass-transition temperature (Tg) (108 °C) and exhibits limited water absorption, was low both in air (0.54 nm/8.75 min) and water (0.86), while PHEMA, which has a high bulk Tg (99 °C) and exhibits high water absorption, exhibited low mobility in air (0.40) but two orders of magnitude higher mobility in water (60). PMEMA, which has a low bulk Tg (14 °C) and exhibits limited water absorption, already started to move in air (4.5), and its mobility moderately increased in water (20). These behaviors were reasonable, considering the bulk Tg and water absorption characteristics of the polymers. Further, the chain mobility in water was compared with that of dried samples at high temperatures in air. The mobility of PMMA, PHEMA, and PMEMA in water corresponded to that of the dried samples observed in air below the surface Tg (97 °C) for PMMA, at ∼125 °C for PHEMA, and at ∼35 °C for PMEMA. In situ real-time AFM analysis of polymer materials in water is an effective method for evaluating the chain mobility at the polymer/water interface.