Asymmetrical Faults Research Articles

Adaptive generalized predictive voltage control of islanded ac microgrid in presence of symmetric and asymmetric faults

Adaptive generalized predictive voltage control of islanded ac microgrid in presence of symmetric and asymmetric faults

Transient Interaction Mechanism Analysis and Stability Control of Multi-paralleled DFIG-Based WTs during Asymmetrical Grid Faults

Transient Interaction Mechanism Analysis and Stability Control of Multi-paralleled DFIG-Based WTs during Asymmetrical Grid Faults

FLACON: A Deep Federated Transfer Learning-Enabled Transient Stability Assessment During Symmetrical and Asymmetrical Grid Faults

FLACON: A Deep Federated Transfer Learning-Enabled Transient Stability Assessment During Symmetrical and Asymmetrical Grid Faults

Fault Current Multi-Stages Calculation Method for DFIG-Based Wind Farms with Whole Fault Process Attributes under Asymmetrical Grid Fault Conditions

Fault Current Multi-Stages Calculation Method for DFIG-Based Wind Farms with Whole Fault Process Attributes under Asymmetrical Grid Fault Conditions

Location of Asymmetric Ground Fault Using Virtual Injected Current Ratio and Two-stage Recovery Strategy in Distribution Networks

Location of Asymmetric Ground Fault Using Virtual Injected Current Ratio and Two-stage Recovery Strategy in Distribution Networks

Synchronization Stability Analysis Based on Dual-Sequence Dynamic Coupling Model for GridFollowing Inverters Under Asymmetrical Grid Faults

Synchronization Stability Analysis Based on Dual-Sequence Dynamic Coupling Model for GridFollowing Inverters Under Asymmetrical Grid Faults

Adaptive Supplementary Control of VSG Based on Virtual Impedance for Current Limiting in Grid-Connected and Islanded Microgrids

By applying virtual synchronous generator (VSG) method in high penetration level microgrids, current limiting issue under fault condition has become an important challenge. The main objective of this paper is to propose a novel current limiting strategy which has the capability of voltage tracking error reduction to avoid voltage controller saturation. This purpose is obtained by adaptive virtual impedance-based reference voltage correction during fault condition. Furthermore, positive and negative peak detection-based current limiting method implemented in double loop control system prepares soft transition ability. Moreover, this current limiting method generates the adaptive term of virtual impedance part. In contrast to conventional VSG methods, the proposed approach provides high quality voltage and current for microgrid in both grid-connected and islanded modes during fault conditions. The offline and hardware in the loop (HIL) simulation results confirm that the peak current of the inverter is restricted to the threshold value under symmetrical and asymmetrical faults for two operating modes of microgrid.

Grid-Forming Control of DFIG-based Wind Turbine Generator by Using Internal Voltage Vectors for Asymmetrical Fault Ride-Through

Grid-Forming Control of DFIG-based Wind Turbine Generator by Using Internal Voltage Vectors for Asymmetrical Fault Ride-Through

A new fault location scheme based on local measurements for transmission lines connected to inverter-based resources

This paper aims to reveal conventional impedance-based fault location methods’ shortcomings in the presence of inverter-based resources (IBRs) through an analytical framework established for the analysis of the IBR sequence impedances. Thereafter, a single-ended method is put forward in order to accurately specify the fault location in the lines emanating from the IBRs. The proposed fault location formulation utilizes the negative and zero sequence currents as alternative polarizing currents, therefore it is independent of the pre-fault data, and it can be applied for all kinds of asymmetrical short circuit fault. Furthermore, the established formulation is further amended to make it applicable to long transmission lines. The suggested method also provides acceptable accuracy in various conditions, such as different fault resistances, different host grid codes, and dynamic behavior of the fault resistance. The performance of the proposed scheme is scrutinized using the PSCAD/EMTDC software with an extensive number of simulations. The obtained results reveal the effectiveness and efficacy of the proposed fault location method in the presence of IBRs.

Simulation-based post-fault analysis in WECS using DFIG systems under an unbalanced fault scenario

Fault analysis in an integrated Wind Energy Conversion System (WECS) is the highest priority factor to be taken into account for distributed generation (DG). The contribution of renewable energies (like solar and wind) to the power system is increasing continuously. New challenges are being faced while integrating such systems because of the no inertial response provided by renewable resources. So, for a reliable integration further exploration, development, and even new strategies are needed to improve the reliability, power quality, control and protection of renewable energy generation. Disintegration in distributed generation is still a huge question mark on the reliability of modern power systems. Disintegration has many causes and faults are one of them, that cause severe voltage profile distortions, which makes WECS a complex system in terms of control and protection of power system. In this work, focus has been paid to the analysis of asymmetrical faults in wind farms and their impacts are evaluated on the overall generation system. A 30 MW wind power plant has been developed in MATLAB to study the faults. Since wind farms are Low Voltage (LV) networks, therefore, fault impedance method (IEC 60909) and the Fort-cue Method have been used for the fault analysis. The fault current response and behaviour of the DG system under asymmetrical fault conditions at different locations in and around the wind farm have been obtained. It is found that fault loop impendence, transformer grounding type, and fault location largely affect the dynamic behaviour of the co-generation system under asymmetrical faults. In this work dynamic behaviour of the wind generation system has been analysed for the different asymmetrical faults induced at different locations of the system. The response of the wind generator has been evaluated based on the different fault simulations considering the sequence component method.

Estimation of powerquality in distribution system using fuzzy logic theory

There are several methods are used to calculate the power quality indicators. These objectives are now served by the most recent soft computing theories, such as neural networks, fuzzy time series, fuzzy logic theory, and other techniques. The fuzzy logic theory is one of the methods used to calculate the power quality indicators for the distribution electric network in this paper. It resolves the issue of forecasting the voltage values on distribution electrical networks' buses and enhances the quality of electricity in the face of fluctuating consumer loads and uncertainty. This paper proposed a device that has the ability for monitoring the quality of electricity domestically which leads to getting rid of many problems such as voltage deviations and asymmetrical faults. The fuzzy logic theory is implemented to develop the algorithm for this purpose. The actual data is recorded at the distribution transformer and implement the fuzzy logic theory by using a mathematical model as well as the simulation on MATLAB for optimizing the power quality indicators with the help of fuzzy logic theory and results are discussed at the end of the paper.

Asymmetric air gap fault detection in linear permanent magnet Vernier machines

PurposeThe aim of this paper is to introduce an accurate asymmetric fault index for the diagnosis of the faulty linear permanent magnet Vernier machine (LPMVM).Design/methodology/approachThree-dimensional finite element method is applied to model the LPMVM. The geometrical and physical properties of the machine, the effect of stator and translator teeth, magnetic saturation of core and nonuniform air gap due to asymmetric fault are taken into account in the simulation. The air gap asymmetric fault is proposed. This analytical method estimates the air gap flux density of an LPMVM.FindingsThis paper presents an analytical method to predict the performance of a healthy and faulty LPMVM. The introduced index is based on the frequency patterns of the stator current. Besides, the robustness of the index in different loads and fault severity is addressed.Originality/valueIntroducing index for air gap asymmetry fault diagnosis of LPMVM.

Development of a Novel Control Scheme to Achieve the Minimum Unbalance Factor and Real Power Fluctuations under Asymmetrical Faults

The increasing share of converter-based renewable energy sources in the power system has forced the system operators to demand voltage support from the converters in case of faults. In the case of symmetric faults, all the phases have equal voltage support, but in the case of asymmetric faults, selective voltage support is required. The grid codes define the voltage support required in the case of symmetric/asymmetric faults, which is the reactive current injection in the respective sequence proportional to its voltage dip, but studies confirm that it does not result in a minimum unbalance factor in the case of asymmetric faults. The unbalance factor is an indication of the level of imbalance voltage among the phases. Moreover, it also results in fluctuated active power injection in the case of asymmetric faults, which causes dc link voltage fluctuations, and the power reversal may also occur due to such fluctuations, which leads to higher protection costs for the dc link. In order to (1) enhance the uniformity of voltage among different phases in the case of asymmetric faults and (2) minimize the real power fluctuations in such conditions, a novel control scheme is presented in this paper. It optimally distributes the negative sequence current phasor into its active and reactive components to achieve the minimum voltage unbalance factor. It also confirms the minimum real power fluctuations by adjusting the positive and negative sequence current phasors. The proposed scheme also ensures the current limit of the converter. The proposed scheme is developed in Matlab/Simulink and tested under different faulty conditions. The results confirm the better performance of the proposed scheme against the grid code recommendation under different faulty conditions.

Research on the Control Method of the PV Grid-Connected Inverter under an Asymmetrical Power Grid Fault

The negative-sequence current component and harmonic components generated when an asymmetrical fault occurs in the power grid seriously affect the normal operation of the photovoltaic (PV) grid-connected inverter. In order to suppress the negative-sequence current component and the harmonic component of the grid-connected current, and to meet the normal grid-connected operation requirements of the PV grid-connected inverter when asymmetrical faults occur in the grid, this paper proposes the proportional integral double-resonant (PI-DR) current controller, which consists of the PI controller and double-resonant controllers. The PI-DR current controller can directly control the negative-sequence current component and the grid-connected current harmonic component in the output current in the forward synchronous rotating coordinate system, without decomposing the positive and negative sequence currents. The PI-DR current controller ensures that the PV grid-connected inverter can realize normal grid-connected operation and improves the quality of the power when an asymmetrical fault occurs in the power grid. MATLAB/Simulink experiments show that the PI-DR current controller can improve the dynamic characteristics of the PV grid-connected inverter and improve the operating capability of the system when an asymmetrical fault occurs in the power grid.

Enhanced DC-link voltage control of PMSG-based wind turbine generators by machine-side converter during asymmetrical grid faults

Under asymmetrical grid fault conditions, oscillating active power can occur on the grid-side converter (GSC) of permanent magnet synchronous generator (PMSG)-based wind turbine generators. The oscillating active power flows into the DC-link, causing voltage oscillations that can lead to a shortened lifetime of DC-link capacitors and additional harmonics injected into the grid. While conventional methods can mitigate the oscillating active power through negative sequence current injection by the GSC, this hinders the grid support of the GSC regarding negative sequence reactive current during grid fault. To address this issue, a novel control scheme is proposed that uses the machine-side converter (MSC) to transfer the oscillating power to the motor. Firstly, the active power capacity of the MSC is analyzed and compared with that of GSC, and the results show that MSC has enough capacity to accommodate the oscillating active power. On this basis, a novel MSC control scheme is proposed to transfer the oscillating active power on the DC-link to the motor, which has a much larger inertia to buffer the power oscillation. Compared with conventional methods, the proposed control scheme relieves the GSC from mitigating the power oscillation to support the grid. Simulation studies using DIgSILENT PowerFactory are presented to verify the effectiveness of the proposed control scheme for PMSG-based wind turbine generators.

Analytical Dual-Sequence Current Injections Feasible Region of Weak-Grid Connected VSC Under Asymmetric Grid Faults

For phase-locked-loop synchronization (PLL-Syn) based Weak-Grid connected Voltage Source Converter (WG-VSC) system under asymmetric grid faults, published works mainly focus on existing of equilibrium point and small signal stability, which cannot address PLL-Syn transient stability problems. For the first time, we have proposed an analytical solution to the question of “ <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">Whether the WG-VSC system can reach to a new available equilibrium point (EP) of fault-on state from original EP of pre-fault state without loss of PLL-Syn transient stability under asymmetric faults?</i> ”. Dual-sequence current injections feasible region (CIFR) of WG-VSCs in positive and negative sequence current injection space is defined firstly. Then, by considering <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">PLL-Syn transient stability constraint, Maximum available current constraint, and PCC Voltage constraint</i> , an analytical expression of CIFR has been obtained. Finally, experiments results based on detailed switching model in RT-BOX hardware-in-loop platform have been provided to verify the CIFR constructed in this paper. It should be noted that the work of this paper can not only address PLL-Syn transient stability problems of WG-VSC system under asymmetric faults, but also can pave the way for asymmetric fault ride-through control considering transient stability constraints.

Modeling of Asymmetrical Grid Faults for P-HIL Accuracy and Stability Analysis in LVRT Tests

Modeling of Asymmetrical Grid Faults for P-HIL Accuracy and Stability Analysis in LVRT Tests

Multi-target fault ride-through strategy for transformerless MMCs under asymmetric grounding faults in AC/DC hybrid distribution networks

In AC/DC hybrid distribution networks (HDNs), when asymmetric grounding faults occur, transformerless multiterminal modular multilevel converters (MMCs) should achieve three key targets of fault ride-through (FRT): 1) limiting the unbalanced fault currents; 2) injecting currents to support grid voltages in case of disconnection from grids; and 3) eliminating the zero-sequence circulating currents (ZSCCs) from fault networks through MMCs to nonfaulted networks. However, in medium voltage-level HDNs, the line impedances are mainly resistive-inductive, and traditional current injection methods are no longer effective. Moreover, in neutral nondirect grounding networks with multiple AC voltage levels, the voltages of nonfaulted phases rise, and it is difficult for MMCs to achieve fault current control. To solve the above issues, this manuscript proposes a multi-target FRT strategy. First, negative-sequence current controllers are used to eliminate the negative-sequence fault currents. Then, to support the positive-sequence voltages of grids, optimal and suboptimal active-reactive current references based on the line impedance ratios are proposed. To help transformerless MMCs with low modulation indices eliminate zero-sequence circulating currents, two zero-sequence voltage compensation modes and an improved zero-sequence current eliminator are proposed. Finally, the proposed fault current control is verified in MATLAB/Simulink.

Low-voltage ride-through capability in a DFIG using FO-PID and RCO techniques under symmetrical and asymmetrical faults

The power grid faults study is crucial for maintaining grid reliability and stability. Understanding these faults enables rapid detection, prevention, and mitigation, ensuring uninterrupted electricity supply, safeguarding equipment, and preventing potential cascading failures, ultimately supporting the efficient functioning of modern society. This paper delves into the intricate challenge of ensuring the robust operation of wind turbines (WTs) in the face of fault conditions, a matter of substantial concern for power system experts. To navigate this challenge effectively, the implementation of symmetrical fault ride-through (SFRT) and asymmetrical fault ride-through (AFRT) control techniques becomes imperative, as these techniques play a pivotal role in upholding the stability and dependability of the power system during adverse scenarios. This study addresses this formidable challenge by introducing an innovative SFRT–AFRT control methodology based on rotor components optimization called RCO tailored for the rotor side converter (RSC) within a doubly-fed induction generator (DFIG) utilized in wind turbine systems. The proposed control strategy encompasses a two-fold approach: firstly, the attenuation of both positive and negative components is achieved through the strategic application of boundary constraints and the establishment of reference values. Subsequently, the optimization of the control characteristic ‘beta’ is accomplished through the utilization of a particle swarm optimization (PSO) algorithm integrated within an optimization loop. This intricate interplay of mechanisms aims to optimize the performance of the RSC under fault conditions. To measure the efficacy of the proposed control technique, a comparative analysis is conducted. Fractional-order (FO) proportional–integral–derivative (PID) controllers are employed as an additional method to complement the novel approach. By systematically juxtaposing the performance of the proposed SFRT–AFRT control technique with the FO-PID controllers, a comprehensive evaluation of the proposed approach's effectiveness is attained. This comparative assessment lends valuable insights into the potential advantages and limitations of the novel control technique, thereby contributing to the advancement of fault mitigation strategies in WT systems. Finally, the paper highlights the economic viability of the proposed control method, suggesting its suitability for addressing broader power network issues, such as power quality, in future wind farm research.

Enhancement of low-voltage ride-through capability for virtual synchronous generators based on virtual impedance voltage control

Virtual Synchronous Generator (VSG)-based grid-forming converters (GFC) increasingly serve as interfaces between renewable energy resources and the power grids with high penetration. Although the emulation of the characteristics of Synchronous Generator (SG) enables GFC to provide virtual inertia and oscillation damping under the VSG control, it remains challenging to replicate the short-circuit behaviors of SGs under the grid voltage sag/recovery conditions. The existing technologies are limited and lack full functionalities in terms of power synchronization, overcurrent suppression and capability of dealing with asymmetric grid-faults. This paper presents a Virtual Impedance Voltage Control (VIVC) strategy to enhance the fault-ride-through capability of the converter under a variety of fault conditions. In the case of asymmetric faults, a negative-sequence current control is performed to mitigate the negative-sequence voltages and achieve the grid current balance. The fault current is restrained and the power synchronization is improved by the virtual reactance without oversizing the GFC. The simulation and experimental results validate the effectiveness of the proposed control strategies.