Aqueous Suspensions Of Carbon Nanotubes Research Articles

Aqueous suspensions of carbon nanotubes: Surface oxidation, colloidal stability and uranium sorption

The objective of this study is to obtain information on the behaviour of carbon nanotubes (CNTs) as potential carriers of pollutants in the case of accidental CNT release to the environment and on the properties of CNTs as a potential adsorbent material in water purification. The effects of acid treatment of CNTs on (i) the surface properties, (ii) the colloidal stability and (iii) heavy metal sorption are investigated, the latter being exemplified by uranium(VI) sorption. There is a pronounced influence of surface treatment on the behaviour of the CNTs in aqueous suspension. Results showed that acid treatment increases the amount of acidic surface groups on the CNTs. Therefore, acid treatment has an increasing effect on the colloidal stability of the CNTs and on their adsorption capacity for U(VI). Another way to stabilise colloids of pristine CNTs in aqueous suspension is the addition of humic acid.

Translational and Rotational Dynamics of Individual Single-Walled Carbon Nanotubes in Aqueous Suspension

Near-infrared fluorescence videomicroscopy has been used to study simultaneously the translational and rotational diffusion of individual semiconducting single-walled carbon nanotubes (SWCNTs) in aqueous suspension. Analysis of translational trajectories revealed diffusion coefficient values from approximately 0.3 to 6 microm(2)/s. The nanotube lengths deduced from these values ranged between approximately 130 nm and 6 microm. From the minor bending motions observed in individual nanotubes several micrometers in length, we confirmed that the shorter SWCNTs of primary interest here can be considered to be rigid rods under normal conditions. Because the nanotubes act as highly rigid, photostable, steady, and anisotropic fluorophores, it was possible to monitor their rotational reorientations through fluctuations in emission intensity under linearly polarized excitation. The magnitudes of observed orientational fluctuations varied substantially among individual nanotubes. These magnitudes correlated strongly with translational diffusion coefficient, reflecting the length dependence of both types of motions. Combined translational and rotational measurements also revealed the influence of local environment on nanotube mobility.

Bundling dynamics of single walled carbon nanotubes in aqueous suspensions

A simple optical method based on absorption of monochromatic light to investigate the dynamics of single walled carbon nanotube (SWCNT) suspensions is described. The well dispersed suspensions display a complex behavior, exhibiting peaks due to resonant scattering from SWCNT bundles with increasing diameters as a function of time. The results indicate that the bundling of SWCNTs initiates almost immediately after termination of sonication (after ∼0.1 h) and continues to increase up to a critical time (∼10 h), above which precipitation according to the Stokes relationship occurs. The absorbance behavior can be explained by the depletion of the effective medium as well as the Mie scattering from growth of bundles. A semiquantitative analysis of the experimental data based on the Mie theory of light scattering from cylindrical particles allows the extraction of diameters at the nucleation and growth of SWCNT bundles. The bundling dynamics have been correlated with the electrical properties such as the sheet resistance and transistor characteristics of the SWCNT thin films. Our work is a useful step toward reproducible solution processed electronics because it provides a simple method to monitor the quality of SWCNT suspensions in real time and correlate it to device characteristics.

The manufacture of carbon nanotubes decorated with ZnS to enhance the ZnS photocatalytic activity

Carbon nanotubes with attached ZnS nanocrystals were prepared by a reaction between Zn(NO 3) 2 and Na 2S in an aqueous suspension of carbon nanotubes. Post-refluxing treatment and the order in which the reactants were introduced played a crucial role in the improvement of the interaction between ZnS nanocrystals and carbon nanotubes. Studies on methylene blue degradation revealed that carbon nanotubes could effectively increase the photocatalytic activity of the ZnS nanocrystals. Close contact between carbon nanotubes and the ZnS improved the interfacial electron transfer and restrained the electron/hole (e−/h+) pair recombination of ZnS.

Fast and Controlled Integration of Carbon Nanotubes into Microstructures

AbstractIn this paper, we report the results of a rapid and room temperature integration approach for the selective and structured deposition of carbon nanotubes (CNTs) into three-dimensional microstructures. The approach exploits electrophoretic deposition (EPD) from an aqueous suspension of CNTs, together with suitably patterned and electrically-energized microstructure-bearing substrates. Uniform 2-D and 3-D micropatterns of CNTs on wafer scale have been achieved in less than 4 minutes with controllable thicknesses ranging from 133nm to several micrometers. Orientation of the deposited CNTs was observed in microstructures with certain dimensions. Surface hydrophobicity of the microstructures was found to be critical in achieving well-defined micropatterning of CNTs. A hydrophobic microstructure surface leads to the selective patterning profiles of CNTs, while a hydrophilic surface induces CNTs assembly over the entire microstructure, with resultant loss of selectivity. This approach can be further extended to fabricate 3-D micropatterns with multilayer materials on flexible substrate through the aid of transfer micromolding techniques.

An experimental study on the pressure drop of nanofluids containing carbon nanotubes in a horizontal tube

This article reports an experimental study on the flow characteristics of the aqueous suspensions of carbon nanotubes (CNTs). Stable nanotube suspensions were made for pressure drop measurements by two different methods. One of them is to disperse nanotubes using a surfactant, and the other is to introduce oxygen-containing functional groups on the CNT surfaces by acid treatment. The pressure drops in a horizontal tube and viscosities of nanofluids were measured and the effects of CNT loading and different preparation methods were investigated. Viscosity measurements show that both CNT nanofluids prepared by two methods are shear thinning fluids and at the same volume fraction, the nanofluids prepared by the acid treatment have much smaller viscosity than the ones made with surfactant. Under laminar flow conditions, the friction factor of CNT nanofluids stabilized by adding surfactant is much larger than that of CNT nanofluids prepared by acid treatment, and both nanofluids show larger friction factors than distilled water. In contrast to this, under turbulent flow conditions, the friction factors of both nanofluids become similar to that of the base fluids as the flow rate increases. It is also shown that as CNT loading is increased, laminar regime of nanofluids has been extended to further higher flow rates, therefore, nanofluids could have low friction factors than pure water flows at certain range of flow rates.

Bioactive ceramic coatings containing carbon nanotubes on metallic substrates by electrophoretic deposition

A range of potentially bioactive ceramic coatings, based on combinations of either hydroxyapatite (HA) or titanium oxide nanoparticles with carbon nanotubes (CNTs), have been deposited on metallic substrates, using electrophoretic deposition (EPD). Sol–gel derived, ultrafine HA powders (10–70 nm) were dispersed in multi-wall nanotube-containing ethanol suspensions maintained at pH = ∼3.5 and successfully coated onto Ti alloy wires at 20 V for 1–3 min For TiO2/CNT coatings, commercially available titania nanopowders and surface-treated CNTs in aqueous suspensions were co-deposited on stainless steel planar substrates. A field strength of 20 V/cm and deposition time of 4 min were used working at pH = 5. Although the co-deposition mechanism was not investigated in detail, the evidence suggests that co-deposition occurs due to the opposite signs of the surface charges (zeta potentials) of the particles, at the working pH. Electrostatic attraction between CNTs and TiO2 particles leads to the creation of composite particles in suspension, consisting of TiO2 particles homogenously attached onto the surface of individual CNTs. Under the applied electric field, these net negatively charged “composite TiO2/CNT” elements migrate to and deposit on the anode (working electrode). The process of EPD at constant voltage conditions was optimised in both systems to achieve homogeneous and reasonably adhered deposits of varying thicknesses on the metallic substrates.

Triazenes as a Stable Diazonium Source for Use in Functionalizing Carbon Nanotubes in Aqueous Suspensions

Organic triazene compounds are stable precursors to diazonium salts for functionalizing single-wall carbon nanotubes (SWNTs) in aqueous media. This method is particularly useful when a target molecule has functionality that will not tolerate diazotization conditions. We illustrate this by detailing the synthesis of a biotin-containing triazene followed by reaction with SWNTs.

Radial breathing mode of single-walled carbon nanotubes: Optical transition energies and chiral-index assignment

We present a comprehensive study of the chiral-index assignment of carbon nanotubes in aqueous suspensions by resonant Raman scattering of the radial breathing mode. We determine the energies of the first optical transition in metallic tubes and of the second optical transition in semiconducting tubes for more than 50 chiral indices. The assignment is unique and does not depend on empirical parameters. The systematics of the so-called branches in the Kataura plot are discussed; many properties of the tubes are similar for members of the same branch. We show how the radial breathing modes observed in a single Raman spectrum can be easily assigned based on these systematics. In addition, empirical fits provide the energies and radial breathing modes for all metallic and semiconducting nanotubes with diameters between 0.6 and 1.5 nm. We discuss the relation between the frequency of the radial breathing mode and tube diameter. Finally, from the Raman intensities we obtain information on the electron-phonon coupling.

Heat transfer of aqueous suspensions of carbon nanotubes (CNT nanofluids)

This paper is mainly concerned about the heat transfer behaviour of aqueous suspensions of multi-walled carbon nanotubes (CNT nanofluids) flowing through a horizontal tube. Significant enhancement of the convective heat transfer is observed and the enhancement depends on the flow conditions (Reynolds number, Re), CNT concentration and the pH, with the effect of pH smallest. Given other conditions, the enhancement is a function of axial distance from the inlet, increasing first, reaching a maximum, and then decreasing with increasing axial distance. The axial position of the maximum enhancement increases with CNT concentration and Re. Given CNT concentration and the pH level, there appears to be a Re above which a big increase in the convective heat transfer coefficient occurs. Such a big increase seems to correspond to the shear thinning behaviour. For nanofluids containing 0.5 wt.% CNTs, the maximum enhancement reaches over 350% at Re = 800, which could not be attributed purely to the enhanced thermal conduction. Particle re-arrangement, shear induced thermal conduction enhancement, reduction of thermal boundary due to the presence of nanoparticles, as well as the very high aspect ratio of CNTs are proposed to be possible mechanisms.

Fluorescence spectroscopy of single-walled carbon nanotubes in aqueous suspension

Optical studies of single-walled carbon nanotubes have advanced greatly through the recent discovery of near-infrared band gap photoluminescence from single-walled carbon nanotubes (SWNT) isolated in aqueous surfactant suspensions. This fluorescence emission has enabled the detection of many distinct optical transitions and their assignment to specific (n,m) semiconducting species of SWNT. The resulting set of precise transition energies presents a challenge to current theoretical models of nanotube electronic structure and a guide to nanotube researchers using resonance Raman spectroscopy. In the near future, structure-resolved fluorimetry should prove useful for revealing the quantitative (n,m) composition of mixed SWNT samples through sensitive, rapid, and nondestructive measurements. It will also permit detailed studies of many physical and chemical processes that vary with nanotube structure.

Processing and characterization of carbon nanotube/poly(styrene-co-butyl acrylate) nanocomposites

Nanocomposite materials were prepared from an amorphouspoly(styrene-co-butyl acrylate) latex as the matrix using an aqueous suspension of carbon nanotubes as the filler. After stirring, the preparations were cast and evaporated. The morphology of the resulting films was examined by scanning electron microscopy and a good dispersion of the filler was observed, except for the 5 wt% filled sample. The electrical conductivity and mechanical behavior in both the linear and non-linear ranges were analyzed. From conductivity measurements, a clear percolation threshold has been observed for a relatively low critical volume fraction around 1.5%. The mechanical characterization displayed a continuous reinforcing effect of the carbon nanotubes without lowering of the elongation at break up to 3 wt%. The thermal stability of the composites was strongly improved by carbon nanotubes loading. For instance, the terminal zone was shifted by 115 K with only 15 wt% of nanotubes.