Aqueous Solution Research Articles

Does the ionic distribution in the electrical double layer modify second harmonic scattering?

Surface-specific nonlinear optical techniques are ideally suited to investigate the complex structure of aqueous interfaces. For colloidal particles dispersed in aqueous solutions, interfacial properties can be retrieved with angle-resolved second harmonic scattering (AR-SHS). The mathematical framework of AR-SHS does not require a priori knowledge on the electrostatic distribution in the first few nanometers close to the interface, therefore allowing us to formulate a molecular-level description of the electrical double layer (EDL) based on the experimental data. However, farther away from the interface, an analytical form of the electrostatic potential decay is necessary to account for the distance dependence of the surface electrostatic field propagating into the solution. This requirement is especially important at low ionic strengths, where the electrostatic field is not efficiently screened by counterions. Here, we examine to what extent the analytical form of the electrostatic potential decay impacts the AR-SHS data analysis. We analyze the effect of different functions on the scattering form factors, on the integrated AR-SHS signal intensity, and on the surface parameters extracted from fitting the AR-SHS data. We find that the trends of the surface parameters remain similar regardless of the chosen function, demonstrating the robustness of our approach to establish a molecular-level picture of the EDL. At ionic strengths <10-4M for 100-nm diameter particles, a functional form that physically represents counterions packed more densely in the vicinity of the surface than in the case of the Poisson-Boltzmann distribution has the largest impact, resulting in an overestimation of the obtained surface potential.

Degradation of pharmaceuticals and other emerging pollutants employing bi-metal catalysts/magnesium and/or (green) hydrogen in aqueous solution.

Contaminations by pharmaceuticals, personal care products, and other emerging pollutants in water resources have become a seriously burgeoning issue of global concern in the first third of the twenty-first century. As societal reliance on pharmaceuticals continues to escalate, the inadvertent introduction of these substances into water reservoirs poses a consequential environmental threat. Therefore, the aim of this study was to investigate reductive degradation, particularly, catalytic hydrogenation regarding model pollutants such as diclofenac (DCF), ibuprofen (IBP), 17α-ethinylestradiol (EE2), or bisphenol-A (BPA), respectively, in aqueous solutions at lab scale. Iron bimetals (zero valent iron, ZVI, and copper, Cu, or nickel, Ni) as well as zero valent magnesium (Mg, ZVM) in combination with rhodium, Rh, or palladium, Pd, as hydrogenation catalysts (HK), were investigated. Studies were executed through various short-term batch experiments, with multiple sample collections, over a total range of 120min. The results indicated that DCF was attenuated at over 90 % when exposed to Fe-Cu or a Fe-Ni bimetal (applied as a single model pollutant). However, when DCF was part of a mixture alongside with IBP, EE2, and BPA, the attenuation efficacy decreased to 79 % with Fe-Cu and 23 % with Fe-Ni. Conversely, both IBP and BPA exhibit notably low attenuation levels with both bimetals, less than 50 %, both deployed as single substances or in mixtures. No reaction (degradation) products could be identified employing LC-MS, but sometimes a release of the parent pollutant when applying an acetic acid buffer could be noted to a certain extent, suggesting adsorption processes on corrosion products such as iron hydroxide and/or oxides. Surprisingly, Mg in combination with Rh (Rh-HK) or Pd (Pd-HK) showed a significantly rapid decrease in the concentrations of DCF, EE2, and BPA, in part up to approximately 100 %, that is, within a few minutes only in part due to hydrogenation degradation reactions (related reaction products could actually be identified by LC-MS; adsorption processes were not observed here). Moreover, kinetic modeling of the DCF degradation with Mg-Rh-HK was conducted at different temperatures (15 °C, 20 °C, 25 °C, 35 °C) and varied initial concentrations (2.5mg/L, 5.0mg/L, 7.5mg/L, 10.0mg/L). The outcomes prove that the degradation of DCF at the Rh-HK's surface followed a modified first-order kinetics, most probably by catalytic hydrodehalogenation and subsequent hydrogenation of the aromatic moieties (molecular hydrogen was provided by the corrosion of Mg). From the determined reaction rate constants at four different temperatures, the activation energy was estimated to be 59.6kJ/mol by means of the Arrhenius equation what is in good agreement with similar results reported in the literature. This coupled hydrodehalogenation and hydrogenation approach may be upscaled into a new promising technical process for comprehensively removing such pharmaceuticals and similar pollutants in sewage plants in a single step, furthermore, even in combination with adsorption by activated carbon and/or ozonation which have already been established at some sewage plants in Switzerland and Germany recently.

Enhanced Near-infrared Phosphorescent Emission Modulated by Clipping of Metallotweezers in Aqueous Media.

Near-infrared phosphorescent materials have received significant attention due to their potential applications in bioimaging and diagnostics. Although, many types of organic phosphors with near-infrared emission have been developed, the low phosphorescence efficiency in aqueous solution hampers their practical applications in biological systems. Hence, there is an urgent need to develop near-infrared phosphorescent materials with high emission efficiency in aqueous media. Metallotweezers, based on d8 transition metal complexes, emerge as the potential candidates for realizing this objective. Specifically, metallotweezers, featuring two positively charged platinum(II) terpyridine and neutral gold(III) diphenylpyridine pincers on diphenylpyridine spacer, have been designed and synthesized, respectively. The pre-organization effect, rendered by the rigid spacer, enables the resulting metallotweezers to complex with each other, resulting in the formation of clipping complex. The synergistic rigidifying and shielding effects of clipping structure results in enhanced phosphorescent emission intensity. Concurrently, due to phase segregation between the clipping units and the polyethylene glycol tail, the clipping complex undergoes self-assembly in aqueous solution, resulting in phosphorescent emission in the near-infrared region. Overall, non-covalent clipping of metallotweezers illustrated in this study presents a new and effective approach toward near-infrared phosphorescent materials.

When Tautomers Matter: UV-Vis Absorption Spectra of Hypoxanthine in Aqueous Solution from Fully Atomistic Simulations.

The UV-Vis spectrum of the solvated purine derivative Hypoxanthine (HYX) is investigated using the Quantum Mechanics/Fluctuating Charges (QM/FQ) multiscale approach combined with a sampling of configurations through atomistic Molecular Dynamics (MD) simulations. Keto 1H7H and 1H9H tautomeric forms of HYX are the most stable in aqueous solution and form different stable complexes with the surrounding water molecules, ultimately affecting the electronic absorption spectra. The final simulated spectrum resulting from the combination of the individual spectra of tautomers agrees very well with most of the characteristics in the measured spectrum. The importance of considering the effect of the solute tautomers and, in parallel, the contribution of the different solvent arrangements around the solute when modeling spectral properties, is highlighted. In addition, the high quality of the computed spectra leads to suggesting an alternative way for acquiring tautomeric populations from combined computational/experimental spectra.

Protector-free, non-plasmonic silver quantum clusters by femtosecond pulse laser irradiation: in situ binding on nanocellulose filaments for improved catalytic activity and cycling performance.

This study introduces a new, facile method to synthesize silver clusters from aqueous silver ion solution by using high intensity femtosecond pulse laser irradiation. The particles obtained in the absence of reducing or capping agents are 1-17 nm in size and presented quantum properties, as characterized by fluorescence, but did not exhibit plasmon signals, which is not a common characteristic of conventional silver nanoparticles. In a further development, small silver quantum clusters (∼1 nm) were bound in situ to wet-spun filaments of cellulose nanofibrils by pulsed laser irradiation. The obtained hybrid filaments as well as free silver quantum clusters revealed a catalytic activity remarkably higher than that of free gold quantum clusters; moreover, the hybrid filaments were found to show improved stability and cycling performance for silver-based catalysis. The present results indicate the potential of femtosecond laser irradiation to generate clusters as well as hybrid systems with excellent performance and reactivity.

Thixotropic Composite Hydrogel Electrode Composed of a Polymer Hydrogelator and Water-Dispersive Tungsten Oxide Flat Microparticles.

Here, we introduce an organic/inorganic composite hydrogel as a versatile gel electrode material. This composite hydrogel was formed by simply mixing an aqueous solution of flat microparticles of tungsten oxide, exhibiting superior water dispersibility, with a hydrogel composed of a water-soluble polyaramide-based polymer hydrogelator. The resulting composite hydrogel exhibited uniform dispersion of tungsten oxide flat particles throughout the hydrogel matrix, supplementing the structure formed by the polymer hydrogelator. It maintained the gel-forming capability and thixotropic behavior inherent to the polymer hydrogelator while showcasing the electrochemical characteristics of tungsten oxide. With its spreadability and applicability to various electrode shapes, a composite hydrogel is presented as a potential spreadable gel electrode material.

One-Stone-for-Two-Birds Method to Improve the SnO2 Layers for High Power-per-Weight Flexible Perovskite Solar Cell Mini-modules.

Maintaining the power conversion efficiency (PCE) of flexible perovskite solar cells (fPSCs) while decreasing their weight is essential to utilize their lightweight and flexibility as much as possible for commercialization. Strengthening the interfaces between functional layers, such as flexible substrates, charge transport layers, and perovskite active layers, is critical to addressing the issue. Herein, we propose a feasible and one-stone-for-two-birds method to improve the electron transport layer (ETL), SnO2, and the interface between the ETL and perovskite layer simultaneously. In detail, poly(acrylate ammonium) (PAAm), a low-cost polymer with a long chain structure, is added into the SnO2 aqueous solution to reduce the aggregation of SnO2 nanoparticles, resulting in the deposition of a conformal and high-quality ETL film on the tin-doped indium oxide film surface. Simultaneously, PAAm addition can effectively regulate the crystallization of the perovskite films, strengthening the interface between the SnO2 film and the buried surface of the perovskite layer. The outstanding PCEs of 22.41% on small-scale fPSCs and 18.54% on fPSC mini-modules are among the state-of-the-art n-i-p type fPSCs. Moreover, the fPSC mini-module on the 20 μm-thick flexible substrate shows a comparable PCE with that of the fPSC mini-module on the 125 μm-thick flexible substrate, exhibiting a high power-to-weight of 5.097 W/g. This work provides an easy but essential direction for further applications of fPSCs in diverse scenarios.

Sequestration of divalent heavy metal ions from aqueous environment by adsorption using biomass-bentonite composites as potential adsorbent: Equilibrium and kinetic studies

Hybrid clay adsorbents have been investigated in recent studies as cheap and effective adsorbents for eliminating micropollutants, such as heavy metal ions from aqueous solution. Here, we modified bentonite (BEN) with palm kernel shell and groundnut shell by calcination to obtain palm kernel shell-modified bentonite (BPKS) and groundnut shell-modified bentonite (BGS). We studied the batch equilibrium adsorption of Pb2+, Cd2+ and Ni2+ ions under the influence of dosage, solution pH, contact time and concentration. Under these conditions, we found that the modified adsorbents (BGS and BPKS) had a higher equilibrium adsorption (qe) for the metal ions than unmodified BEN. BEN exhibited Langmuir adsorption capacities (Qo) of 32.47, 14.04 and 14.16 mg/g for Pb2+, Cd2+ and Ni2+, respectively. BGS and BPKS had Qo values of 29.15, 14.27, 16.61 and 31.75, 17.67, 15.625 mg/g for Pb2+, Cd2+, Ni2+, respectively. Investigations revealed that the rate of adsorption on the three adsorbents is best described by a pseudo-second-order kinetic model, with R2 values ≥ 0.9; the intra-particle diffusion model establishes a surface interaction mechanism involving the exchange of electrons between the surfaces of the adsorbents and the adsorbate. Scanning electron microscopy results suggest porous and heterogeneous adsorbent surfaces, indicating a physio-sorption phenomenon. The modifications increased the surface area of BEN from 78.435 to 194.850 and 140.650 m2/g in BGS and BPKS, respectively, using BET surface area analysis. However, the average pore width of BEN reduces from 3.8 to 3.3 nm in both BGS and BPKS. Also, the modification enhanced the cation exchange capacity in BPKS only. The findings from this study offered invaluable insights into how biomass can enhance the physicochemical properties of BEN, as needed for practical environmental application and/or optimization, during the removal of Pb2+, Cd2+ and Ni2+ ions from aqueous media.

Influence of biochar on the removal of Microcystin-LR and Saxitoxin from aqueous solutions

The present study assessed the effective use of biochar for the adsorption of two potent HAB toxins namely, Microcystin-LR (MCLR) and Saxitoxin (STX) through a combination of dosage, kinetic, equilibrium, initial pH, and competitive adsorption experiments. The adsorption results suggest that biochar has excellent capabilities for removing MCLR and STX, with STX reporting higher adsorption capacities (622.53–3507.46 µg/g). STX removal required a minimal dosage of 0.02 g/L, while MCLR removal needed 0.4 g/L for > 90%. Similarly, a shorter contact time was required for STX removal compared to MCLR for > 90% of toxin removed from water. Initial pH study revealed that for MCLR acidic conditions favored higher uptake while STX favored basic conditions. Kinetic studies revealed that the Elovich model to be most suitable for both toxins, while STX also showed suitable fittings for Pseudo-First Order and Pseudo-Second Order in individual toxin systems. Similarly, for the Elovich model the most suited kinetic model for both toxins in presence of each other. Isotherm studies confirmed the Langmuir–Freundlich model as the best fit for both toxins. These results suggest adsorption mechanisms including pore filling, hydrogen bonding, π–π interactions, hydrophobic interactions, electrostatic attraction, and dispersive interactions.

Adsorption of Chromium (III) and Chromium (VI) Ions from Aqueous Solution Using Chitosan–Clay Composite Materials

Adsorption of Chromium (III) and Chromium (VI) Ions from Aqueous Solution Using Chitosan–Clay Composite Materials

Solution Behavior of Glyco-Copoly(l-Glutamic Acid)s in Dilute Saline Solution.

A small series of copoly(α,l-glutamic acid/dl-allylglycine)s with the same chain length and allylglycine content (∼10 mol %) but different spatial distribution of allylglycine units was synthesized and subsequently glycosylated via thiol-ene chemistry. Dilute aqueous copolypeptide solutions (0.1 wt %, physiological saline) were analyzed by circular dichroism spectroscopy, dynamic light scattering, and cryogenic transmission electron microscopy. The copolypeptides adopted a random coil or α-helix conformation, depending on solution pH, and the glycosylated residues either distorted or enhanced the folding into an α-helix depending on their location and spatial distribution along the chain. However, regardless of their secondary structure and degree of charging, all partially glycosylated copolypeptides self-assembled into 3D spherical structures, supposedly driven by a hydrophilic effect promoting microphase separation into glucose-rich and glutamate-rich domains.

Open-Framework Vanadate as Efficient Ion Exchanger for Uranyl Removal.

The elimination of uranium from radioactive wastewater is crucial for the safe management and operation of environmental remediation. Here, we present a layered vanadate with high acid/base stability, [Me2NH2]V3O7, as an excellent ion exchanger capturing uranyl from highly complex aqueous solutions. The material possesses an indirect band gap, ferromagnetic characteristic and a flower-like morphology comprising parallel nanosheets. The layered structure of [Me2NH2]V3O7 is predominantly upheld by the H-bond interaction between anionic framework [V3O7]nn- and intercalated [Me2NH2]+. The [Me2NH2]+ within [Me2NH2]V3O7 can be readily exchanged with UO22+. [Me2NH2]V3O7 exhibits high exchange capacity (qm = 176.19 mg/g), fast kinetics (within 15 min), high removal efficiencies (>99%), and good selectivity against an excess of interfering ions. It also displays activity for UO22+ ion exchange over a wide pH range (2.00-7.12). More importantly, [Me2NH2]V3O7 has the capability to effectively remove low-concentration uranium, yielding a residual U concentration of 13 ppb, which falls below the EPA-defined acceptable limit of 30 ppb in typical drinking water. [Me2NH2]V3O7 can also efficiently separate UO22+ from Cs+ or Sr2+ achieving the highest separation factors (SFU/Cs of 589 and SFU/Sr of 227) to date. The BOMD and DFT calculations reveal that the driving force of ion exchange is dominated by the interaction between UO22+ and [V3O7]nn-, whereas the ion exchange rate is influenced by the mobility of UO22+ and [Me2NH2]+. Our experimental findings indicate that [Me2NH2]V3O7 can be considered as a promising uranium scavenger for environmental remediation. Additionally, the simulation results provide valuable mechanistic interpretations for ion exchange and serve as a reference for designing novel ion exchangers.

{SeO2(OH)} Bridging Lanthanide-Containing Antimono-Seleno-Tungstates.

A series of new trigonal pyramidal {SeO2(OH)} bridging lanthanide-containing antimono-seleno-tungstates [H2N(CH3)2]8Na8Cs4H9[Ln2SeW4O11(OH)(H2O)4(SbW9O33)(SeW9O33)(Se1/2Sb1/2W9O33)]2·32H2O [Ln = Tb (1), Dy (2), Ho (3), Er (4)] have been prepared by the synthetic strategy of simultaneously using the antimonotungstate precursor and simple material in an acidic aqueous solution and structurally characterized by single-crystal X-ray diffraction, powder X-ray diffraction, IR spectrometry, and thermogravimetric analysis. Their molecular structures contain an unprecedented hexameric polyoxoanion [Ln2SeW4O11(OH)(H2O)4(SbW9O33)(SeW9O33)(Se1/2Sb1/2W9O33)]229- constituted by two equivalent trimeric subunits Ln2W4O9(H2O)4(SbW9O33)(SeW9O33)(Se1/2Sb1/2W9O33) bridged via two μ2-{SeO2(OH)} linkers. Furthermore, the catalytic oxidation of various aromatic sulfides and sulfur mustard simulant 2-chloroethyl ethyl sulfide (CEES) by compound 3 as the heterogeneous catalyst has been investigated, exhibiting high conversion and selectivity as well as good stability and recyclability.

Sensitivity, precision, and accuracy of fs-LIBS for heavy metal detection in flowing aqueous solutions

Sensitivity, precision, and accuracy of fs-LIBS for heavy metal detection in flowing aqueous solutions

Efficient Capture and Electroreduction of Dilute CO2 into Highly Pure and Concentrated Formic Acid Aqueous Solution.

High-purity CO2 rather than dilute CO2 (15 vol %, CO2/N2/O2 = 15:80:5, v/v/v) similar to the flue gas is currently used as the feedstock for the electroreduction of CO2, and the liquid products are usually mixed up with the cathode electrolyte, resulting in high product separation costs. In this work, we showed that a microporous conductive Bi-based metal-organic framework (Bi-HHTP, HHTP = 2,3,6,7,10,11-hexahydroxytriphenylene) can not only efficiently capture CO2 from the dilute CO2 under high humidity but also catalyze the electroreduction of the adsorbed CO2 into formic acid with a high current density of 80 mA cm-2 and a Faradaic efficiency of 90% at a very low cell voltage of 2.6 V. Importantly, the performance in a dilute CO2 atmosphere was close to that under a high-purity CO2 atmosphere. This is the first catalyst that can maintain exceptional eCO2RR performance in the presence of both O2 and N2. Moreover, by using dilute CO2 as the feedstock, a 1 cm-2 working electrode coating with Bi-HHTP can continuously produce a 200 mM formic acid aqueous solution with a relative purity of 100% for at least 30 h in a membrane electrode assembly (MEA) electrolyzer. The product does not contain electrolytes, and such a highly concentrated and pure formic acid aqueous solution can be directly used as an electrolyte for formic acid fuel cells. Comprehensive studies revealed that such a high performance might be ascribed to the CO2 capture ability of the micropores on Bi-HHTP and the lower Gibbs free energy of formation of the key intermediate *OCHO on the open Bi sites.

New strategy for structure rearrangement of thin-film composite (TFC) polyamide (PA) membranes and offering potential use in both aqueous and organic solvents

The purity of sodium hexafluorophosphate (NaPF6) is crucial for the preparation of electrolytes in manufacturing. We propose a simple process in order to induce membrane structure rearrangement process (SRP) by activating thin-film composite (TFC) membranes with polyamide (PA) structure and explore their potential green recycling application in concentrating sodium-ion batteries (SIBs) electrolyte. The method utilizes a solution containing polar aprotic solvent as the soaking and activating solution to swell and disintegrate the loosely cross-linked PA layer, and a non-solvent solidification solution complete the SRP, enhancing the permeability of the PA layer while maintaining high rejection rates for divalent ions. Subsequently, during the further treatment of the membrane surface in structure rearrangement, tert-butanol (TBA) is introduced into the aqueous solution to reconstruct the surface PA layer, further improving the permeability. The optimal D8010T10 achieved a permeation flux of 24.2 L m−2 h−1·bar−1, with rejection rates for sodium sulfate (Na2SO4), magnesium chloride (MgCl2), and magnesium sulfate (MgSO4) reaching 94.7 %, 98.4 %, and 99.1 % respectively. And the mechanism of SRP with different solvent is analyzed and explained through dissipative particle dynamics (DPD) simulations. This study provides a commercially viable approach for manufacturing high-performance membranes. The D8010T10 membrane achieves more than 90 % separation efficiency for sodium hexafluorophosphate (NaPF6) dissolved in different solvents, providing a potential solution for the concentration and recovery of NaPF6 in lab-scale, verified its potential use in the organic solvent nanofiltration (OSN) and a path way for waste membrane recycling and degrading use in the industry.

Sorption Characteristics and Chromatographic Separation of 90Y3+ from 90Sr2+ from Aqueous Media by Chelex-100 (Anion Ion Exchange) Packed Column

There is growing demand for separation of 90Y carrier free from 90Sr coexisting to produce high purity 90Y essential for radiopharmaceutical uses. Thus, in this context the sorption profiles of Y3+ and Sr2+ from aqueous solutions containing diethylenetriaminepenta acetic acid (DTPA), ethylenediaminetetra-acetic acid (EDTA), acetic acid, citric acid, or NaCl onto Chelex-100 (anion ion exchange) solid sorbent were critically studied for developing an efficient and low-cost methodology for selective separation of Y3+ from Sr2+ ions (1.0 × 10−5 M). Batch experiments displayed relative chemical extraction percentage (98 ± 5.4%) of Y3+ from aqueous acetic acid solution onto Chelex-100 (anion ion exchanger), whereas Sr2+ species showed no sorption. Hence, a selective separation of Y3+ from its parent 90Sr2+ has been established based upon percolation of the aqueous solution of Y3+ and Sr2+ ions containing acetic acid at pH 1-2 through Chelex-100 sorbent packed column at a 2 mL min−1 flow rate. Y3+ species were retained quantitatively while Sr2+ ions were not sorbed and passed through the sorbent packed column without extraction. The sorbed Y3+ species were then recovered from the sorbent packed column with HNO3 (1.0 M) at a 1.0 mL min−1 flow rate. A dual extraction mechanism comprising absorption associated to “weak-base anion exchanger” and “solvent extraction” of Y3+ as (YCl6)3− and an extra part for “surface adsorption” of Y3+ by the sorbent is proposed. The established method was validated by measuring the radiochemical (99.2 ± 2 1%), radionuclide purity and retardation factor (Rf = 10.0 ± 0.1 cm) of 90Y3+ recovered in the eluate. Ultimately, the sorbent packed column also presented high stability for reusing 2-3 cycles without drop in its efficiency (±5%) towards Y3+ uptake and relative chemical recovery. A proposed flow sheet describing the analytical procedures for the separation of 90Y3+ from 90Sr2+ using chelating Chelex 100 (anion exchange) packed column is also included.

Highly Selective Photooxidation of Benzyl Alcohol to Benzaldehyde by Bi–Mo/g-C3N4 in Aqueous Solution

Highly Selective Photooxidation of Benzyl Alcohol to Benzaldehyde by Bi–Mo/g-C₃N₄ in Aqueous Solution

Effects of Gamma Irradiation on Polyethylene Terephthalate and Detection of Microplastic Particles Down to 1 μm.

In response to increasing concern about the impact of plastic degradation on the environment, this study investigates the degradation of virgin and recycled polyethylene terephthalate (PET) under γ-irradiation in aqueous solutions, with particular focus on the resulting formation of microplastic particles (MP). By exposing both virgin and recycled PET samples to different doses of γ-irradiation (10, 50, and 100 kGy), a comprehensive analysis using UV-vis spectroscopy, dynamic light scattering (DLS) and micro-Raman spectroscopy is presented. The results, highlighted by micro-Raman spectroscopy, show that γ-irradiation produces micrometer-sized plastic particles, with the recycled PET having a significantly higher MP content than its original counterpart. Careful examination reveals the presence of a stabilizer in samples of recycled PET juice bottles. This study not only contributes to our understanding of the effects of γ-irradiation on PET but also highlights the need for further research into the environmental impact of such processes. The insights gained shed light on the behavior of PET under γ-irradiation and the resulting impact on microplastic pollution and make an important contribution to our understanding of the broader environmental context.

The hydrates of chlorogenic acid in its aqueous solution and in stored food products

AbstractChlorogenic acids (CQAs), a large family of naturally occurring esters of quinic acid with one, two or even three cinnamic acids moieties and/or moieties of cinnamic acids derivatives, supplied to human organisms mainly with coffee, tea, fruit and vegetables, have been among the most frequently studied polyphenols. Of these, caffeic acid esters predominate, and 5-O-caffeoylquinic acid (5-CQA) is their main and most widespread representative. Recently performed studies have shown that after removing water from the aqueous solution of 5-CQA, its dry residue contains two hydrates of this compound, each consisting of two 5-CQA molecules and two molecules of H2O (2 × 5-CQA*2xH2O). The results presented in the paper not only define the characteristic features of 5-CQA but, more importantly, offer solid evidence that 5-CQA hydrates begin to form already in the aqueous solution of 5-CQA immediately after the dissolution of this compound and that the analogous process can occur in food products containing 5-CQA during their storage. Moreover, the performed experiments indicate the validity of the hypothesis that 5-CQA hydrates are formed by active collisions of 5-CQA molecules with monomeric/dimeric water molecules existing in trace amount in strongly associated aqueous systems. The presence of 5-CQA hydrates in liquid food products may have a significant impact on the assessment of some of their physicochemical properties as well as their biochemical activity.