Aqueous Li-ion Batteries Research Articles

A Flexible Multifunctional Cyanoethyl-Modified Bacterial Cellulose Nanofiber Framework for High-Energy and High-Power Density Aqueous Li-Ion Batteries.

Aqueous rechargeable lithium-ion batteries (ARLIBs) are extensively researched due to their inherent safety, typical affordability, and potential high energy density. However, fabricating ARLIBs with both high energy density and power performance remains challenging. Herein, based on cyanoethyl-modified bacterial cellulose nanofibers (CBCNs), a multifunctional fast ion transport framework is developed to construct the flexible free-standing ARLIBs with high areal loading and excellent rate performance. Benefiting from the unique merits of CBCNs, such as ultra-high aspect ratio, excellent toughness, superior adhesion, good lithiophilicity and ideal stability, the flexible free-standing and highly robust electrodes are fabricated and exhibit a long-term stable cycling of 1200 cycles with a high specific capacity of 117 mAh∙g-1 at 15 C. Remarkably, the corresponding full cell with the free-standing high mass loading (45.5 mg∙cm-2) electrodes under the condition of ultra-low addition of battery binder demonstrates a cycle lifespan of over 1000 cycles with a specific capacity of 120 mAh∙g-1 and a capacity decay as low as 0.03% per cycle, which is far superior to those of almost all previous reports. This work provides a strategy for constructing ARLIBs with high energy density and power performance by introducing a unique fast ion transport nanofiber framework.

Superior electrochemical performances of Lithium vanadium oxide with coconut shell-based porous carbon as the anode of the aqueous Li ion battery

Carbon materials, as the skeleton structure of electrode materials, are composited with lithium-ion anode materials, which not only increase the electrical conductivity of the materials, but also enhance the electrochemical performance of the electrode materials. In this paper, LiV3O8@C composites were prepared by using coconut shell-based porous carbon to structurally modulate aqueous lithium-ion anode materials. And three composites with different structures and sizes were successfully synthesized by hydrothermal method, hydrothermal stirring method and improved solid-phase method. After XRD and SEM analyses, it was found that all three composites maintained the monoclinic crystal system structure of LiV3O8, and the materials prepared by the hydrothermal method showed a smooth layer structure, while the materials prepared by the hydrothermal stirring method and the solid-phase method showed nanorods with different sizes. The prepared anode materials and LiFePO4 cathode materials were assembled into an aqueous lithium-ion full battery, and were subjected to charge/discharge tests, cyclic voltammetry and electrochemical impedance spectroscopy. The results indicate that the electrochemical performances of the three composites are significantly improved compared with the pure LiV3O8. Specifically, the discharge capacities of the two groups of nanorod-like composites were 112.2 mAh/g and 85.5 mAh/g at a rate of 0.2 C, which were improved by as much as two times compared with the pure LiV3O8. However, the composite material with layered structure not only reaches an initial discharge specific capacity of 148.39 mAh/g, which is 2.7 times higher than that of the pure LiV3O8, but also effectively slows down the dissolution effect of LiV3O8 by compositing with the carbon material, and at the same time, it shows excellent rate performance.

The enhancement and impact of Se doping on the electrochemical properties of LiMn2O4 cathode material for aqueous Li-ion batteries

Spinel LiMn2O4 is a promising cathode material for lithium-ion batteries. However, due to the Jahn-Teller effect and Mn dissolution, its capacity decreases seriously in the cycle process, which hinders its wider application. In the course of our research, we discovered that a modest infusion of Se-doping is capable of significantly augmenting the oxygen vacancy within the material, improve the conductivity of the LiMn2O4 material and promotes superior battery performance. Moreover, due to Se-doped the average valence state of Mn is raised, which effectively mitigates the Jahn-Teller effect. The optimized sample exhibits high capacity, long cycle life, and superior rate capability, with an initial discharge specific capacity of 101.0 mAh·g−1 at 7 C and capacity retention of 87.3 % after 200 cycles. The maximum specific discharge capacity of the full battery during the cycle was 97.9 mAh·g−1, the capacity retention rate after 200 cycles was 78.2 %, and the maximum energy density during the cycle is 145.1 Wh·Kg−1, which was nearly twice that of the single lithium-ion battery in this paper. The effect of Se-doped on the properties of LiMn2O4 cathode materials provides a new idea for the development of high-performance spinel lithium manganese oxide cathode materials.

Solvation Structures and Transport Mechanisms of Cations in Water-in-Bisalt Electrolytes for High-Concentration Lithium-Ion Batteries Revealed by Molecular Dynamics Simulations.

The development of safe and cost-effective electrolytes for rechargeable batteries is currently underway. While water-based electrolytes hold promise, their restricted electrochemical stability window poses a challenge. Combining multiple ionic species emerges as a promising strategy to broaden this stability window and optimize Li-ion battery performance. This study focuses on dual-cation electrolytes, which blend lithium and potassium acetates to enhance the electrochemical characteristics of the solution at high concentrations. We investigated the solvation structure of each ion and its interactions on a molecular level. Our analysis reveals that ion clusters and aggregates are formed through shared acetate and water molecules at high salt concentrations. Furthermore, the residence time analyses of atom pairs indicate that cations diffuse in vehicular mode at low concentrations. In contrast, they switch to a structural mode at high concentrations due to diminishing water content. This study offers a comprehensive model for exploring diverse solvation structures of cations and gaining insights into their diffusion mechanisms within water-in-bisalt electrolytes for aqueous Li-ion batteries.

Order-disorder structural engineering of vanadium oxide anode: Balancing ionic and electronic dynamic for fast-charging aqueous Li-ion battery

Fast-charging aqueous lithium-ion batteries (ALIBs) are considered as promising energy storage devices because of their non-flammability and environmentally friendly characteristics. However, how to balance the ionic and electronic dynamics for fast charging reactions remains a significant challenge under the current research status. Here, the order-disorder structural engineering strategy is adopted to resolve this issue, considering the difference between ion and electron transportation in the crystalline and amorphous phases, respectively. Vanadium oxide anodes were developed with optimized ionic and electronic dynamics by using an organic-inorganic hybrid material as a precursor along with refined regulation on the calcination temperature and time. This facile and large-scale extendable approach harnesses the benefits of the order-disorder structure to optimize Li+ storage efficiency and facilitate the high reversibility of Li-ion during fast charging. Consequently, the order-disorder V2O5-based full cell with LiMn2O4 as a cathode exhibits high specific capacity (262.71 mAh g−1, 89.35 % of the theoretical capacity of V2O5), high energy density (166.04 Wh kg−1), fast Li-ion diffusion coefficient (7.34×10−5 cm2 s−1) and fast-charging performance (only 6 min achieves 82.84 % of initial state-of-charge capacity). This work explores the ionic and electronic dynamic of ordered-disorder structure and offers new insights into the development of fast-charging metal ion batteries.

Aluminum corrosion–passivation regulation prolongs aqueous batteries life

Aluminum current collectors are widely used in nonaqueous batteries owing to their cost-effectiveness, lightweightness, and ease of fabrication. However, they are excluded from aqueous batteries due to their severe corrosion in aqueous solutions. Here, we propose hydrolyzation-type anodic additives to form a robust passivation layer to suppress corrosion. These additives dramatically lower the corrosion current density of aluminum by nearly three orders of magnitude to ~10−6 A cm−2. In addition, realizing that electrochemical corrosion accompanies anode prelithiation, we propose a prototype of self-prolonging aqueous Li-ion batteries (Al ||LiMn2O4 ||TiO2), whose capacity retention rises from 49.5% to 70.1% after 200 cycles. A sacrificial aluminum electrode where electrochemical corrosion is utilized is introduced as an electron supplement to prolong the cycling life of aqueous batteries. Our work addresses the short-life issue of aqueous batteries resulting from the corrosion of the current collector and lithium loss from side reactions.

A Comparative Study of Degradation Behaviors of LiFePO4, LiMn2O4, and LiNi0.8Mn0.1Co0.1O2 in Different Aqueous Electrolytes

Aqueous Li-ion batteries (ALIBs) are an important class of battery chemistries owing to the intrinsic non-flammability of aqueous electrolytes. However, water is detrimental to most cathode materials and could result in rapid cell failure. Identifying the degradation mechanisms and evaluating the pros and cons of different cathode materials are crucial to guide the materials selection and maximize their electrochemical performance in ALIBs. In this study, we investigate the stability of LiFePO4 (LFP), LiMn2O4 (LMO) and LiNi0.8Mn0.1Co0.1O2 (NMC) cathodes, without protective coating, in three different aqueous electrolytes, i.e., salt-in-water, water-in-salt, and molecular crowding electrolytes. The latter two are the widely reported “water-deficient electrolytes.” LFP cycled in the molecular crowding electrolyte exhibits the best cycle life in both symmetric and full cells owing to the stable crystal structure. Mn dissolution and surface reduction accelerate the capacity decay of LMO in water-rich electrolyte. On the other hand, the bulk structural collapse leads to the degradation of NMC cathodes. LMO demonstrates better full-cell performance than NMC in water-deficient aqueous electrolytes. LFP is shown to be more promising than LMO and NMC for long-cycle-life ALIB full cells, especially in the molecular crowding electrolyte. However, none of the aqueous electrolytes studied here provide enough battery performance that can compete with conventional non-aqueous electrolytes. This work reveals the degradation mechanisms of olivine, spinel, and layered cathodes in different aqueous electrolytes and yields insights into improving electrode materials and electrolytes for ALIBs.

A thin, intrinsically stretchable MXene-MWCNTs/polymer current collector for deformable aqueous Li-ion batteries

By integrating Ti3C2Tx with MWCNTs on an elastic SEBS film, a thin, intrinsically stretchable hybrid conductor was constructed and used to fabricate deformable aqueous Li-ion batteries.

Bridging Aqueous and Organic Electrolytes: Intercalation Mechanism of TiS2 in Sustainable Aqueous Li-Ion Batteries

Aqueous Li-ion batteries (ALiBs) are a promising alternative for large-scale grid storage owing to water's non-flammability, low cost, and ease of purification. However, the narrow electrochemical stability window (ESW) of water (1.23 V) significantly limits the energy density of ALiBs, compared to their non-aqueous counterpart. The use of a highly concentrated electrolyte, such as 21 mol kg-1 (molality, m) of LiTFSI in water, known as the “water-in-salt” (WiS) electrolyte, can widen the water ESW to ~3 V, but its high cost and low environmental sustainability hinder the commercialization of ALiBs. Therefore, we explored the feasibility of cycling layered TiS2 anodes in ALiBs containing dilute electrolytes (i.e. 2 m LiTFSI in water).We obtained a reversible discharge capacity of ca. 80 mAh g-1 at a current density of 50 mA g-1. By employing three-electrode cycling with online electrochemical mass spectrometry, we identified potential-dependent gas evolution from the cell triggered by multiple chemical/electrochemical reactions, such as (1) solvent co-intercalation, (2) partial TiS2 exfoliation, and (3) TiS2-catalyzed water splitting in dilute aqueous electrolytes. We also identified a completely different potential profile of TiS2, when cycled in an aqueous electrolyte, with two distinct redox plateaus at 2.95 V and 2.88 V, followed by a sloping region until 2.3 V (all vs. Li+/Li0). Recall that in classic non-aqueous electrolytes, TiS2 shows a characteristic sloping profile centered at ca. 2.2 V, the peculiar potential profile suggests a different intercalation mechanism of TiS2 in aqueous electrolytes.In this presentation, we will share our latest findings from complementary physicochemical and computational methods to tackle the complex interfacial reactivity between layered anodes and aqueous electrolytes. Operando synchrotron X-ray diffraction data revealed the reversible uptake-release of water molecules between TiS2 layers, which was also confirmed energetically favorable by theoretical modeling. By introducing triethyl phosphate (TEP) as a co-solvent, we successfully tuned the electrochemical intercalation behavior of TiS2 from purely Li-intercalation (as in non-aqueous systems, when using only TEP as the solvent) to hydrated-Li-intercalation (as in concentrated and dilute aqueous electrolytes, when using water/TEP mixtures as the solvent). These findings suggest that solvent co-intercalation can be a promising strategy for ALiBs. The general implication of these results on the electrode-electrolyte interface and interphase in aqueous batteries will be systematically discussed in the talk. Overall, our work provides new perspectives on developing sustainable energy storage technologies. Figure 1

Interfacial Chemistry in Aqueous Lithium-Ion Batteries with Dilute Aqueous Electrolytes: A Case Study with V2O5

Aqueous lithium ion batteries (ALIBs) are promising candidates for large-scale energy storage systems, benefiting from the intrinsic safe and environmentally friendly properties of aqueous electrolytes. However, its practical application is impeded due to the narrow electrochemical stability windows (ESWs) of aqueous electrolytes. Despite that increasing electrolyte concentration can achieve a wide ESW with the protection of SEI layer, it brings numerous disadvantages induced by excessive salt as well. Therefore, understanding the SEI formation mechanism and further widening the ESWs of dilute aqueous electrolytes are critical for the breakthrough of next-generation ALIBs.Herein, the interphase chemistry of V2O5 electrode with dilute aqueous electrolyte was systematic investigated by conducting various Operando characterizations with LMO||V2O5 cell system. Dynamic SEI, which consists of Li2CO3, LiF and V2O4, was formed during charge and disappeared during the following discharge, which is strongly affected by electrolyte pH fluctuation. Moreover, its evolution process is reversible during cycling. There are several impacts affect the pH fluctuation during cycling. First, V2O5 dissolution, which turns electrolyte into acidic before cycling, and is aggravated by electrolyte concentration decrease. Second, proton/hydronium ion insertion, which takes place on electrode surface in dilute electrolyte, while it is suppressed by concentration increase due to reduced proton concentration. Third, the redox reaction of dissolved V2O5, which is controlled by both potential and electrolyte pH change according to the V-H2O poubaix diagram. Along with the anode potential decrease and the alkalinisation of electrolyte, V2O4 is formed on anode surface by the reduction of HV10O28 5- and V4O12 4- and this reduction process further produces hydroxide ion into electrolyte. Last, the carbon oxidation, which takes place on cathode side during charge and on anode side during the final discharge. Therefore, the acidification of electrolyte during cycling is detrimental to SEI stability in aqueous electrolytes. This systematic research work provides new perspectives to the understanding of the interphase chemistry evolution in aqueous Li-ion batteries using dilute electrolytes, which guides the building of effective SEI layer in aqueous Li-ion batteries and beyond. Figure 1

(Invited) Engineering Local Chemical Environments in Electrolytes and at Electrode-Electrolyte Interface for Efficient Aqueous Batteries

Electrolytes are an essential component of energy storage devices. Electrolyte composition has a significant impact on the environmental footprint, safety, price and performance of a battery. Aqueous electrolytes are non-flammable and can offer safer battery operation and lower toxicity. However, they suffer from a smaller electrochemical stability window compared to traditional organic electrolytes, which leads to lower energy density. To circumvent the small electrochemical stability window, highly concentrated “water-in-salt” (WIS) electrolytes, which demonstrate significantly wider stability window, were proposed and successfully applied to various aqueous energy storage systems including Li-ion and Zn metal batteries that are highly attractive for grid energy storage. However, since WIS electrolytes require large amounts of salt (often toxic) and have dramatically increased viscosity, it in turn limits their transport properties, charge-discharge rates, and usability in batteries.In this talk, the use of highly concentrated "water-in-salt" (WIS) electrolytes as a means of achieving increased charging efficiency and a wider stability window will be discussed in the context of aqueous Li-ion and Zn metal batteries. Further, we elaborate the role of cation solvation environment, electrolyte structure and hydrogen bonding on the physicochemical properties and electrochemical response of the system. We show that electrolyte composition affects the interfacial kinetics of Zn plating/stripping as well as the kinetics of the parasitic processes of electrolyte decomposition. Finally, we discuss how relatively dilute electrolytes can be engineered for efficient aqueous batteries. References Suo, O. Borodin, T. Gao, M. Olguin, J. Ho, X. Fan, C. Luo, C. Wang and K. Xu, Science, 2015, 350, 938Yamada, K. Usui, K. Sodeyama, S. Ko, Y. Tateyama and A. Yamada, Nat. Energy, 2016, 1, 16129R. Lukatskaya, J.I. Feldblyum, D.G. Mackanic, F. Lissel, D.L. Michels, Y. Cui, Z. Bao, Energy Environ. Sci., 2018, 11, 2876-2883 D.G. Vazquez, T. P. Pollard, J. Mars, J.M. Yoo, H.G. Steinrück, S. E. Bone, O. V. Safonova, M. F. Toney, O. Borodin, M.R. Lukatskaya, Energy Environ. Sci., 2023, DOI: 10.1039/D3EE00205E

Highly Efficient Spatially-Temporally Synchronized Construction of Robust Li3 PO4 -rich Solid-Electrolyte Interphases in Aqueous Li-ion Batteries.

Solid electrolyte interphase (SEI) makes the electrochemical window of aqueous electrolytes beyond the thermodynamics limitation of water. However, achieving the energetic and robust SEI is more challenging in aqueous electrolytes because the low SEI formation efficiency (SFE) only contributed from anion-reduced products, and the low SEI formation quality (SFQ) negatively impacted by the hydrogen evolution, resulting in a high Li loss to compensate for SEI formation. Herein, we propose a highly efficient strategy to construct Spatially-Temporally Synchronized (STS) robust SEI by the involvement of synergistic chemical precipitation-electrochemical reduction. In this case, a robust Li3 PO4 -rich SEI enables intelligent inherent growth at the active site of the hydrogen by the chemical capture of the OH- stemmed from the HER to trigger the ionization balance of dihydrogen phosphate (H2 PO4 - ) shift to insoluble solid Li3 PO4 . It is worth highlighting that the Li3 PO4 formation does not extra-consume lithium derived from the cathode but makes good use of the product of HER (OH- ), prompting the SEI to achieve 100 % SFE and pushing the HER potential into -1.8 V vs. Ag/AgCl. This energetic and robust SEI offers a new way to achieve anion/concentration-independent interfacial chemistry for the aqueous batteries.

The potentials of LiMnPO4 cathode material for aqueous Li-ion batteries: An investigation into solid state and green chemistry approaches

The phospho-olivine LiMnPO4 nanocrystal holds promise as a cathode material for next-generation Li-ion batteries (LIBs). In this study, we employed solid-state and green chemistry approaches to prepare LiMnPO4 powders, with aloe vera extract serving as a capping agent for the latter approach. Selective synthesis of nanoparticles with more active sites for efficient Li+ intercalation-deintercalation was achieved. The phase purity, morphology, and composition of the nanoparticles were characterized using XRD, SEM/TEM, and EDS, respectively. Electrochemical performance was evaluated through cyclic voltammetry, galvanostatic charge-discharge, and electrochemical impedance spectroscopy (EIS) in an aqueous environment. The solid-state synthesized LiMnPO4 nanoparticles (LiMnPO4-SS) exhibited electrolyte-dependent performance but demonstrated good reversibility of Li+ extraction and insertion. Specific capacity, retention of discharge capacity, and Coulombic efficiency were found to be 92.3 ± 0.5 mAhg−1, 98 %, and 93 %, respectively, after 50 cycles at 0.2 C. Additionally, energy density was measured as 15.8 ± 1.4 Whkg−1 at 189.2 ± 1.9 Wkg−1 power density. The green-synthesized LiMnPO4 nanoparticles (LiMnPO4-GS) showed a specific capacity of 106.4 ± 0.9 mAhg−1 (corresponding to ∼62 % of theoretical capacity) after 50 cycles, with capacity retention of ∼97 % and ∼80 % Coulombic efficiency. The energy density was 18.2 ± 1.7 Whkg−1 at 218.1 ± 2.1 Wkg−1 power density. EIS measurements indicated reduced charge transfer resistance for LiMnPO4-GS, optimizing interfacial electrochemical reaction activity. The observed regular micromorphology and (200) plane of nanosized LiMnPO4 contributed to the excellent electrochemical performance. Overall, this investigation highlights the correlation among synthesis method, calcination temperature, electrolyte, crystal structure, and morphology, providing insights for the design of next-generation LIBs.

Passivated Bi2Se3 electrode in Na2CO3 solution to improve anode efficiency in aqueous Li-ion batteries

Efficient anode materials are crucial for the success of aqueous rechargeable lithium-ion batteries (ALIBs) since many materials degrade significantly during electrochemical reactions. In this study, the modification of Bi2Se3 with Na2CO3 was explored to enhance the charge–discharge characteristics of the anode. The passivated Bi2Se3 electrode exhibited improved electrochemical performance, maintaining high charge and discharge capacities of 816 mAh·g−1 after the 5th cycle and 570 mAh·g−1 after the 100th cycle with stable Coulombic efficiency of 98.0 ± 1.2 %. Charge-discharge profiles and cyclic voltammetry revealed the lithium intercalation and deintercalation, while impedance spectroscopy indicated changes in the electrode structure during cycling. These findings highlight the potential of using Bi2Se3 electrodes with a pre-formed surface film to enhance the stability and performance of ALIBs.

Dual Electrolyte Additives Enabling Bilayer SEI to Suppress Hydrogen Evolution Reaction in Aqueous Li-Ion Batteries

Aqueous Li-ion batteries (LIBs) feature safe operation, low cost, and environmental friendliness, but suffer from low energy density due to narrow electrochemical stability window (ESW) of aqueous electrolytes. While exploiting high-salt-concentration strategy of water-in-salt electrolytes (WiSEs) is effective in improving the electrochemical stability, the improvement is still insufficient to ensure practical feasibility of aqueous LIBs. In particular, the reduction stability of WiSEs needs further improvement to enable stable operation of low-voltage anode materials including Li4Ti5O12.This talk reports that the co-use of two electrolyte additives can effectively expand the cathodic limit of various WiSE systems. The synergistic effect between the two additives is attributed to the formation of unique solid-electrolyte interphase composed of organic and inorganic bilayers. The inner inorganic layer suppresses hydrogen evolution reaction, while the outer hydrophobic organic polymer mitigates the dissolution of inner SEI. LiMn2O4/Li4Ti5O12 cells employing 21 m LiTFSI WISE with the dual additives exhibit excellent long-term cycling (>70% retention after 400 cycles at 25 oC) and good rate capability (110 mAh/g at 6 mA/cm2). The efficacy of the dual-additive approach is also demonstrated for other WiSE solutions including water-in-bisalt, hydrate melt, and aqueous/organic hybrid electrolytes, suggesting the general applicability of the dual-additive strategy. Figure 1

Strengthening Aqueous Electrolytes without Strengthening Water.

Aqueous electrolytes typically suffer from poor electrochemical stability; however, eutectic aqueous solutions-25 wt.% LiCl and 62 wt.% H3 PO4 -cooled to -78 °C exhibit a significantly widened stability window. Integrated experimental and simulation results reveal that, upon cooling, Li+ ions become less hydrated and pair up with Cl- , ice-like water clusters form, and H⋅⋅⋅Cl- bonding strengthens. Surprisingly, this low-temperature solvation structure does not strengthen water molecules' O-H bond, bucking the conventional wisdom that increasing water's stability requires stiffening the O-H covalent bond. We propose a more general mechanism for water's low temperature inertness in the electrolyte: less favorable solvation of OH- and H+ , the byproducts of hydrogen and oxygen evolution reactions. To showcase this stability, we demonstrate an aqueous Li-ion battery using LiMn2 O4 cathode and CuSe anode with a high energy density of 109 Wh/kg. These results highlight the potential of aqueous batteries for polar and extraterrestrial missions.

Anion-Induced Interfacial Liquid Layers on LiCoO2 in Salt-in-Water Lithium-Ion Batteries.

The incompatibility of lithium intercalation electrodes with water has impeded the development of aqueous Li-ion batteries. The key challenge is protons which are generated by water dissociation and deform the electrode structures through intercalation. Distinct from previous approaches utilizing large amounts of electrolyte salts or artificial solid-protective films, we developed liquid-phase protective layers on LiCoO2 (LCO) using a moderate concentration of 0.5∼3 mol kg-1 lithium sulfate. Sulfate ion strengthened the hydrogen-bond network and easily formed ion pairs with Li+, showing strong kosmotropic and hard base characteristics. Our quantum mechanics/molecular mechanics (QM/MM) simulations revealed that sulfate ion paired with Li+ helped stabilize the LCO surface and reduced the density of free water in the interface region below the point of zero charge (PZC) potential. In addition, in situ electrochemical surface-enhanced infrared absorption spectroscopy (SEIRAS) proved the appearance of inner-sphere sulfate complexes above the PZC potential, serving as the protective layers of LCO. The role of anions in stabilizing LCO was correlated with kosmotropic strength (sulfate > nitrate > perchlorate > bistriflimide (TFSI-)) and explained better galvanostatic cyclability in LCO cells.

Water-in-salt electrolytes made saltier by Gemini ionic liquids for highly efficient Li-ion batteries

The water-in-salt electrolytes have promoted aqueous Li-ion batteries to become one of the most promising candidates to overcome safety concerns/issues of traditional Li-ion batteries. A simple increase of Li-salt concentration in electrolytes can successfully expand the electrochemical stability window of aqueous electrolytes beyond 2 V. However, necessary stability improvements require an increase in complexity of the ternary electrolytes. Here, we have explored the effects of novel, Gemini-type ionic liquids (GILs) as a co-solvent systems in aqueous Li[TFSI] mixtures and investigated the transport properties of the resulting electrolytes, as well as their electrochemical performance. The devices containing pyrrolidinium-based GILs show superior cycling stability and promising specific capacity in the cells based on the commonly used electrode materials LTO (Li4Ti5O12) and LMO (LiMn2O4).

Layered transition metal oxides (LTMO) for oxygen evolution reactions and aqueous Li-ion batteries.

This perspective paper comprehensively explores recent electrochemical studies on layered transition metal oxides (LTMO) in aqueous media and specifically encompasses two topics: catalysis of the oxygen evolution reaction (OER) and cathodes of aqueous lithium-ion batteries (LiBs). They involve conflicting requirements; OER catalysts aim to facilitate water dissociation, while for cathodes in aqueous LiBs it is essential to suppress water dissociation. The interfacial reactions taking place at the LTMO in these two distinct systems are of particular significance. We show various strategies for designing LTMO materials for each desired aim based on an in-depth understanding of electrochemical interfacial reactions. This paper sheds light on how regulating the LTMO interface can contribute to efficient water splitting and economical energy storage, all with a single material.

Solid‐Electrolyte Interphase for Ultra‐Stable Aqueous Dual‐Ion Storage

AbstractThe solid‐electrolyte interphase (SEI) is the key component of the electrochemical electrode as a passivation layer, which enables a long calendar life for commercial applications. However, owing to the poor understanding of aqueous SEI in conventional aqueous electrolytes, the adoption of aqueous Li‐ion batteries (ALIBs) has been drastically limited. Herein, the construction of a robust aqueous SEI is successfully demonstrated by introducing a ladderized heterocyclic polymer electrode into a water‐in‐salt electrolyte, leading to ultra‐stable dual‐ion storage with long‐term calendar life. The sophisticated SEI composed of fluorinated/oxygenated species is revealed. Electrochemical and structural analysis confirm that such SEI formation is characterized by a proton co‐intercalation, which consumes the water in the Li+'s solvation shell to trigger the subsequent decomposition of organic anions. This new SEI formation path is expected to broaden the horizons of aqueous SEI and open new avenues for the design of versatile electrode materials for further advances in ALIBs.