Antenna Performance Research Articles

Embedded system controlled switching system for reconfigurable antennas

AbstractA multiband and reconfigurable antenna is the one of the main aspects in the communication system which has an extremely important role. An embedded based solution for the fast operation of a reconfigurable antenna to work in a specific operating frequency band is the solution of future technologies. Embedded based solution increases the speed by avoiding the dependence on manual control of the RF switching elements. In this paper, the proposed embedded system‐controlled switching mechanism operate the reconfigurable antenna in any one of the operating bands by a single command to be send from a remote location. The embedded system receives the command and configure a set of PIN diodes as per the modes. The proposed solution consists an Arduino UNO board as motherboard, SIM900A as GSM module to receive the command from user, biasing circuit to control the operation of PIN diode, PIN diode to reconfigure the patch pattern and a user mobile for sending AT command.The proposed model is successful and tested on proteus software 8.0. The model is also deployed on the newly designed multiple‐input‐multiple‐output antenna where the result shows the successful operation to achieve multiband frequency operation.

A low-profile 3-D printable metastructure for performance improvement of aperture antennas

In order to increase the radiation performance of aperture-type antennas, this paper demonstrates a low-profile, planar, single-layer, three-dimensional (3-D) printable metastructure. The proposed hybridized metastructure is highly transparent as it is made out of novel hybrid meta-atoms having transmission coefficient magnitudes greater than – 0.72 dB and fully complies with the near-field phase transformation principle. The hybridized design approach makes the metastructure planar, low-profile, light in weight, and compatible with additive printing technology. For the proof-of-concept, such metastructure is developed and numerically verified to enhance the radiation performance of a resonant cavity antenna (RCA). With the proposed metastructure, the peak directivity of the RCA is improved by 8.6 dBi (from 11.4 dBi to 20 dBi) at the operating frequency of 12.4 GHz. The aperture efficiency and 3-dB directivity bandwidth of the RCA with the metastructure are 41.46% and 16.5%, respectively. Using readily accessible thermoplastics or polymers and copper with cost-effective fused deposition modeling (FDM) 3-D printing technology, the proposed planar hybridized metastructure can be prototyped commercially.

Feasibility and performance of TiCN-based patch antennas for microwave antenna applications

Feasibility and performance of TiCN-based patch antennas for microwave antenna applications

A comparative study of dielectric substrate materials effects on the performance of microstrip patch antenna for 5G/6G application

A comparative study of dielectric substrate materials effects on the performance of microstrip patch antenna for 5G/6G application

Study on the Conductivity Effect on the Characteristics of a Wideband Printed Dipole Antenna Implemented with Silver Nanoparticle Ink

This study examined a flexible composite wideband dipole antenna implemented with conductive silver nanoparticle ink having different conductivities. Two identical split ring resonators (SRRs) were designed to encompass each arm of a dipole element, and each dipole arm and its coupled SRR were printed on the top and bottom sides of a dielectric substrate. The overall dimensions of the compact antenna were 10 mm × 74.8 mm × 0.254 mm (0.053λo × 0.399λo × 0.0014λo at 1.6 GHz). The characteristics of the antenna with different conductivities were numerically investigated and experimentally confirmed. Our investigation aimed to ascertain the proposed antenna's response to different conductivity values and to determine the range of conductivity values that generates major changes in the antenna's performance characteristics in terms of impedance bandwidth, gain, and radiation efficiency. At conductivity values less than approximately 6.0 × 104 S/m, the number of generated resonances changed from three to two, and the antenna experienced a nearly 3-dB gain reduction when the conductivity approached 5.8 × 104 S/m.

A Circular Shape Arc Slot Ultra-Wideband Antenna for Biomedical Applications

In modern communication systems, ultra-wideband (UWB) technology has garnered substantial attention due to its superior attributes compared to traditional narrowband communication systems. Over the past decade, UWB technology has also found applications in microwave-based imaging systems. This study introduces a simple planar coplanar waveguide-fed circular shape arc slot antenna designed specifically for biomedicine and microwave medical imaging applications. The proposed design is implemented on a 1.6-mm-thick FR4 substrate with a relative permittivity of 4.4 and a loss tangent of 0.0009. The antenna has physical dimensions of 26 mm × 29 mm and achieves an impressive bandwidth of 16.6 GHz, spanning 2.4 to 19 GHz. It exhibits a peak gain of 2.5 dBi and consistent omnidirectional radiation characteristics. Thorough temporal analysis validates the antenna's performance within acceptable limits, which is further affirmed through practical fabrication and testing, demonstrating strong agreement with simulation results.

Analysis of tumor detection using polydimethylsiloxane based wearable antenna

Abstract A Polydimethylsiloxane (PDMS) based antenna is designed for skin tumor detection. The antenna functions at 2.45 GHz with a bandwidth of 2.30–2.64 GHz working in the ISM (Industrial, Scientific, and Medical) band. The size of the antenna is 40 × 40 × 1 mm3. This antenna detects tumors in the skin by considering the variations in values of the E-field, J-surf, and H-field. Various analyses such as the distance between the patch and stacked layer skin phantom for different tumor sizes and input power to the antenna are changed and antenna performance is observed. A significant amount of changes is attained which denotes the presence of the tumor. The proposed antenna is fabricated and the corresponding results are analyzed in the Anechoic Chamber. The antenna has an efficiency of 99 % with a Specific Absorption Rate of 1.3846 W/kg which is lower than 1.6 W/kg as per the recommendations of FCC standard.

Broadband Antenna Operating in Sub 6GHz Frequency for Long Range 5G Communication

Abstract: A novel broadband antenna designed for long-range 5G communication in the sub-6GHz frequency band is presented. Through rigorous optimization and simulation, the antenna achieved high gain, low side-lobe levels, and uniform radiationpatterns. Experimental validation confirms its efficacy, offering a compact and robust solution for advancing global connectivity in next-generation wireless networks

Individually adjustable emission from a quantum emitter embedded in a double bowtie-bullseye plasmonic nanoantenna

Single-photon sources have a wide range of applications in fields such as quantum computing and quantum communications. These applications require single-photon sources to possess both high emission directionality and a high Purcell factor. However, currently, there is no satisfactory solution that can meet both of these characteristics. Here, we present a novel hybrid plasmonic nanoantenna that addresses this challenge. The hybrid nanoantenna comprises a bullseye antenna with a double bowtie antenna placed at its center. This design enables the simultaneous achievement of high directionality and a high Purcell factor. Specifically, the Purcell factor can reach up to 10,000, and the emitted photons are predominantly concentrated in the 0° direction in the far-field emission pattern. To characterize the hybrid nanoantenna and investigate the influence of its dimensions on directionality and Purcell factor, we conducted Finite-Difference Time-Domain (FDTD) simulations. The results demonstrate promising findings for enhancing the performance of plasmonic antennas. Moreover, this platform holds potential for the development of efficient single-photon sources, thereby facilitating advancements in photonic integrated circuits and quantum devices.

Antena Dwi Port Dwi Pengutuban Bulat terinspirasi Bahan Meta untuk Sistem Komunikasi Satelit Kecil

This paper presents a dual circular polarized C-band patch antenna for a small satellite communication system The antenna consists of two different annular patch structure with three split ring resonators. The antenna is designed considering space environment and the smallest form of satellite structure. The antenna is fabricated space qualified substrate material Rogers 5880 with overall dimension of 85.22× 48.59 × 1.575 mm3. The antenna achieves circular polarization at 5.1 GHz and 5.2 GHz frequency for port 2 and port 1, respectively. The split ring resonator structures contribute to enhance antenna gain and axial beamwidth. Realized gain of 7.29 dB and 7.33 dB are achieved at 5.1 GHz and 5.2 GHz operating frequency with 3dB axial beamwidth of 170 ̊ and 153 ̊ , respectively. Antenna size and performance show that the antenna can be a potential candidate for smooth operation of small satellite communication system.

Antena Tatasusun Grid Lut Sinar dengan Sel Suria Terpeka Pewarna (DSSC)

Wireless communication systems require electrical energy to operate and function. Whereas standalone applications require reliable power sources which can be realised by photovoltaic technology. Typically, photovoltaic cells and antennas are two separate devices. These devices compete for space in mobile or standalone systems, where available space is generally very limited. To address this issue, a combination of an antenna and a solar cell into a single device is needed. Integrating an antenna with a solar cell is challenging due to the importance of maintaining a compact, simple design while achieving optimal efficiency for both elements. This study focuses on designing a transparent grid array antenna integrated with Dye-Sensitized Solar Cells (DSSC) for Ku-band applications. The grid array design aims to improve antenna performance and is chosen for its suitability with the design and structure of the solar antenna device. The integrated antenna and solar cell were simulated using Computer Simulation Technology (CST) software at a frequency of 14 GHz for Ku-band applications. A prototype of the antenna and solar cell was fabricated, then tested and measured for the efficiency of both the antenna and solar elements. For the solar element, performance measurements were conducted using a halide lamp to mimic sunlight, with results presented in the form of current-voltage curves. In summary, by the end of this study, a transparent solar antenna for Ku-band applications was successfully designed with a gain exceeding 10 dBi. The solar cell’s performance showed an open-circuit voltage (V<sub>OC</sub>) of 0.6733 V, a short-circuit current density (J<sub>SC</sub>) of 2.06 mA/cm², a fill factor (f<sub>F</sub>) of 29.31%, and a power conversion efficiency (η) of 0.407%.

Study the potential of micro laser sintering additive manufacturing technology for metallic 3D printing horn antenna structure

AbstractApplications for an antenna structure produced with additive manufacturing technology are numerous and promising. This study focuses explicitly on utilizing micro‐laser sintering (MLS) three‐dimensional (3D) printing technology to fabricate two rectangular horn antennas identical to a standard Pasternack® horn antenna, making the fabrication straightforward. The objective is to investigate how surface roughness affects antenna performance in a frequency range of 18 to 26.5 GHz. One antenna is polished and the other is left untouched, resulting in surface roughness of 4 and 6 µm, respectively, measured using a profilometer. Then, a vector network analyzer was used to assess their reflection coefficient, transmission characteristics, and radiation pattern and determine gains of 8.83 and 9.14 dBi for the polished and unpolished antennas, respectively. The study finds that both polished and unpolished antennas perform similarly, and their characteristics closely resembling simulated and standard antennas. Finally, the performance of the MLS‐printed metallic antennas is compared with horn antennas created using other 3D printing techniques. It reveals that the MLS‐printed metallic structures exhibit better performance, indicating that the MLS technology has great potential to print 3D metallic electromagnetic designs.

A high-performance sub-THz planar antenna array for THz sensing and imaging applications

Terahertz (THz) spectral region from 0.1 to 3 THz is envisaged to hold immense potential in the next generation of wireless technologies. Recently, research has focused on this terahertz gap, because of its unprecedented channel capacities. At the physical layer, the design complexities and fabrication of THz devices, especially antennas are the prime bottlenecks to realize its full potential. This article introduces a cost-effective, easy-to-fabricate, and reproducible sub-THz antenna design based on a single-layer planar printed circuit board technology. The antenna incorporates carefully designed quasi-cross slots and applied machine learning-assisted global optimization techniques to achieve the desired performance metrics. The antenna performance is elucidated through numerical simulations and verified through a rigorous in-house THz experimental framework around 100–110 GHz. The proposed antenna offers a peak gain of 13.90 dBi with less than 1 dB variation within the entire band of 100–110 GHz. The antenna holds the potential to achieve terabits per second data rates and futuristic high-resolution short-range THz imaging applications.

Correction to: A Modified Regression Model for Analysing the Performance of Metamaterial Antenna Using Machine Learning and Deep Learning

Correction to: A Modified Regression Model for Analysing the Performance of Metamaterial Antenna Using Machine Learning and Deep Learning

Compact CPW-fed Antenna with Controllable WLAN Band-rejection for Microwave Imaging

This work presents the design and experimental validation of a compact frequency reconfigurable coplanar waveguide (CPW)-fed ultra-wideband (UWB) antenna with a capability to on-demand reject WLAN frequencies within the range of 5.15 GHz to 5.85 GHz, specifically tailored for applications in microwave imaging. The design and experimental results are presented and discussed. The bandwidth enhancement is obtained by using T-shaped slots between the feedline and the ground plane of the antenna, and the WLAN band is rejected by using an open loop resonator (OLR) placed on the antenna backside. Switching between UWB with and without WLAN band-notched modes is performed using a PIN diode and a bias circuit. The simulation results corroborate well with the experimental data and clearly showed an interesting frequency reconfigurable behavior for use in microwave imaging applications. An antenna performance simulation and analysis model is presented for breast tumor detection, and the tumor effect has been noticed for both operating modes of the antenna.

A compact wideband low‐profile all textile on/off body antenna for Satcom and defense applications

SummaryA compact, flexible, low‐profile end‐fire broadband wearable antenna operating in Ku‐band /X‐band is proposed in this manuscript for defense and satellite communications (Satcom) applications. The main objective of this work is cross‐polarization reduction by the defected ground structure (DGS), which offers a wider bandwidth. Due to its flexibility and ability to absolutely conform to the curved‐shaped human body, denim fabric is used as a substrate, whereas copper tape is used as a conductor, which allows for the integration of the antenna into garments and makes it appropriate for a wide range of wearable applications in various bands. The prototype has been developed with a size of mm3 for experimental validation. The measured results from a fabricated prototype are well matched with the simulated ones of the proposed design, which indicate a wide bandwidth of 57.35% (7.76–14 GHz) appropriate for use in applications such as defense operating from 8 to 12 GHz, satellite TV (11.7–12.2 GHz), Ku‐band downlink (10.95–11.7 GHz), Ku‐band uplink (11.7–14.5 GHz), and a high gain of 5.1 dBi. The specific absorption rate (SAR) is much below the permissible limit of 1.6 W/kg, with better radiation characteristics. Thus, the proposed antenna is more compact, and it clearly achieves a smaller footprint, larger impedance bandwidths, and a low SAR with potential prospect for Satcom and defense purposes.

Comprehensive accuracy analysis for large closed-loop deployable structures based on matrix structure analysis and linear-complementarity-based contact analysis of spatial joint clearances

The surface accuracy of the deployable structure is crucial in determining the electromagnetic performance of the large satellite antenna. This paper proposes a comprehensive accuracy analysis framework for deployable structures considering clearances of spatial joints, geometric deviations, elastic deformations, external loads, and preloads, all of which can affect surface accuracy during the assembly process. Surface accuracy is calculated by combining the global equilibrium analysis of the deployable structure with the local equilibrium analysis of clearance-affected joints. First, a global elastostatic equilibrium analysis of the deployable structure is performed based on a unified mathematical formulation that describes the elasticity of beams and joints. Then, the local equilibrium analysis for the clearance-affected joints is transformed into a quadratic optimization problem through a linear-complementarity-based method. This method avoids the necessity for a combinatorial search for several traditional discontinuous contact configurations. Considering both global and local equilibrium in iterative analysis, the surface accuracy of the antenna is calculated. This integration avoids prior artificial assumptions about contact configurations of the joints. Finally, the proposed method is validated by comparing it with simulations and experimental results.

A Miniaturized Dual-Band Circularly Polarized Implantable Antenna for Use in Hemodialysis.

Hemodialysis is achieved by implanting a smart arteriovenous graft (AVG) to build a vascular pathway, but reliability and stability in data transmission cannot be guaranteed. To address this issue, a miniaturized dual-band circularly polarized implantable antenna operating at 1.4 GHz (for energy transmission) and 2.45 GHz (for wireless telemetry), implanted in a wireless arteriovenous graft monitoring device (WAGMD), has been designed. The antenna design incorporates a rectangular serpentine structure on the radiation surface to reduce its volume to 9.144 mm3. Furthermore, matching rectangular slots on the radiation surface and the ground plane enhance the antenna's circular polarization performance. The simulated effective 3 dB axial ratio (AR) bandwidths are 11.43% (1.4 GHz) and 12.65% (2.45 GHz). The simulated peak gains of the antenna are -19.55 dBi and -22.85 dBi at 1.4 GHz and 2.45 GHz, respectively. The designed antenna is implanted in a WAGMD both in the simulation and the experiment. The performance of the system is simulated in homogeneous human tissue models of skin, fat, and muscle layers, as well as a realistic adult male forearm model. The measurement results in a minced pork environment align closely with the simulation results.

Design and Performance of Dual Band Microstrip Nano-Fractal Patch Antenna

Design and Performance of Dual Band Microstrip Nano-Fractal Patch Antenna

Metasurface loaded dual band antenna for high gain on- and off- body communication

Metasurfaces are specially made materials designed to have unique properties not found in nature. They are categorized into different types, such as artificial magnetic conductor (AMC), partial reflecting surfaces (PRS), and frequency selective surfaces (FSS). Among these, FSS is commonly used in today’s technology to improve antenna performance, especially in boosting signal strength by blocking unwanted radiation. Recent research is focused on creating FSS-based antennas for Ultra-wideband (UWB) or single band applications, with a significant emphasis on enhancing signal strength. Unlike traditional methods, this study concentrates on designing antennas that are both simple in shape and offers broader frequency coverage, specifically for 2.45 GHz and 5.8 GHz applications. To enhance antenna performance, a dual-band FSS is employed, optimizing the system for improved operation at both resonating frequencies. This results in a high-gain antenna system, which is further investigated for body area network (BAN) systems, considering the crucial performance metric of specific absorption rate (SAR). The findings are compared with recently reported FSS-based antennas to underscore their scientific contribution and potential for high gain, low SAR applications within the 2.45 GHz and 5.8 GHz frequency bands.