Anode Spot Mode Research Articles

Investigation of ion behavior associated with anode-spot mode transition in vacuum arcs

The ion behavior phenomenon associated with transitions of the anode discharge mode to the anode-spot mode is studied by measuring the wall ion current and by spectroscopic observation in vacuum arcs. The anode mode transfers when the wall ion current attains a certain magnitude that is independent of the cathode, but dependent on the anode. The ion-current function to the arc current increases when the arc current increases in the diffuse arc. Spectral-line intensity of Cu III emitted from the plasma in the anode region increases with an instantaneous arc current of a 5-kA peak (kAp) sinusoidal half-wave. These findings suggest an idea for the mode transition, that an ion generation region appears, and that an increase in the ion density produces a positive potential hump near the anode, which results in the negative anode voltage drop triggering the mode transition. After the mode transition, an arc current is found to reduce the ion current near the crest of a sinusoidal current in a copper arc. This appears to be significant for the arc on a small anode. The decrease in the ion current is attributed to the recombination of ions decelerated by anode vapor with electrons emitted from the hot spot on the anode. >

A Review of Anode Phenomena in Vacuum Arcs

This paper discusses arc modes at the anode, anode temperature measurments, anode ions, transitions of the arc into various modes (principally the anode-spot mode), and theoretical explanations of anode phenomena. A vacuum arc can exhibit five anode discharge modes: 1) a low-current mode in which the anode is basically passive, acting only as a collector of particles emitted from the cathode; 2) a second low-current mode that can occur if the electrode material is readily sputtered (a flux of sputtered atoms will be emitted by the anode); 3) a footpoint mode, characterized by the appearance of one or more luminous spots on the anode (footpoints are much cooler than the true anode spots present in the last two modes); 4) an anode-spot mode in which one large or several small anode spots are present (such spots are very luminous, have a temperature near the atmospheric boiling point of the anode material, and are a copious source of vapor and ions); and 5) an intense-arc mode where an anode spot is present, but accompanied by severe cathode erosion. The arc voltage is relatively low and quiet in the two low-current modes and the intense-arc mode. It is usually high and noisy in the footpoint mode, and it can be either in the anode-spot mode. Anode erosion is low, indeed negative, in the two low-current modes, and it is low to moderate in the footpoint mode. Severe anode erosion occurs in both the anode-spot and intense-arc modes.

Time- and Spatially Resolved Spectroscopy of the Plasma State Prior to and during Anode-Spot Formation in High-Current Vacuum Arcs

The emission of numerous lines was measured from a vacuum arc between an Al cathode and Cu anode in which the diffuse, anode-spot, and intense arc modes are observed during a single pulse. An increase in Cu emission and a decrease in Al emission are observed at the transition to the anode-spot mode, and increases in both Al and Cu emission are observed at the transition to the intense-arc mode. Spatial profiles of the excited-state density and Boltzmann-distribution temperatures could be obtained at several positions in the gap. The results show not only a clear correspondence between arc voltage and the arc appearance during different arc modes, but also distinctly different spectral emission properties and droplet behavior.

Vacuum Arc Anode Phenomena

This paper briefly reviews anode phenomena in vacuum arcs, specially experimental work. It discusses, in succession, arc modes at the anode, anode temperature measurements, anode ions, transitions of the arc into various modes (principally the anode spot mode), and theoretical explanations of anode phenomena. The two most common anode modes in a vacuum arc are a low current mode where the anode is basically passive, acting only as a collector of particles emitted from the cathode, and a high current mode with a fully developed anode spot. Characteristically this anode spot has a temperature near the atmospheric boiling point of the anode material and is a copious source of vapor and energetic ions. However, other anode modes can exist. A low current vacuum arc with electrodes of readily sputterable material may emit a flux of sputtered atoms from the anode. Usually this sputtered flux will have little effect upon the vacuum arc, but in certain circumstances it could be significant. A vacuum arc doesn't always transfer directly from a low current mode to the anode spot mode. In appropriate experimental conditions, formation of an anode spot may be preceded by the formation of an anode footpoint. This footpoint is luminous, but much cooler than a true anode spot. Finally, (again in appropriate circumstances) several small anode spots may form instead of one large anode spot. With sufficient increase in arc current or arcing time these will usually combine to form a single large active spot.