Ambient Ionization Techniques Research Articles

A Low-Cost, Simplified Platform of Interchangeable, Ambient Ionization Sources for Rapid, Forensic Evidence Screening on Portable Mass Spectrometric Instrumentation

Portable mass spectrometers (MS) are becoming more prevalent due to improved instrumentation, commercialization, and the robustness of new ionization methodologies. To increase utility towards diverse field-based applications, there is an inherent need for rugged ionization source platforms that are simple, yet robust towards analytical scenarios that may arise. Ambient ionization methodologies have evolved to target specific real-world problems and fulfill requirements of the analysis at hand. Ambient ionization techniques continue to advance towards higher performance, with specific sources showing variable proficiency depending on application area. To realize the full potential and applicability of ambient ionization methods, a selection of sources may be more prudent, showing a need for a low-cost, flexible ionization source platform. This manuscript describes a centralized system that was developed for portable MS systems that incorporates modular, rapidly-interchangeable ionization sources comprised of low-cost, commercially-available parts. Herein, design considerations are reported for a suite of ambient ionization sources that can be crafted with minimal machining or customization. Representative spectral data is included to demonstrate applicability towards field processing of forensic evidence. While this platform is demonstrated on portable instrumentation, retrofitting to lab-scale MS systems is anticipated.

Detection of Hydrocarbons by Laser Assisted Paper Spray Ionization Mass Spectrometry (LAPSI MS).

Here we introduce a new ambient ionization technique named laser assisted paper spray ionization mass spectrometry (LAPSI MS). In it, a 532 ± 10 nm, ≤10 mW laser pointer was shone on a triangularly cut paper along with high voltage, to effect ionization. The analyte solution was continuously pushed through a fused silica capillary, using a syringe pump, at a preferred infusion rate. LAPSI MS promises enhanced ionization with high signal intensity of polycyclic aromatic hydrocarbons (PAHs), which are normally not ionizable with similar ionization methods involving solvent sprays. LAPSI MS works both in positive and negative modes of ionization. A clear enhancement of signal intensity was visualized in the total ion chronogram for most analytes in the presence of the laser. We speculate that the mechanism of ionization is field assisted photoionization. The field-induced distortion of the potential well can be large in paper spray as the fibers comprising the paper are separated at tens of nanometers apart, and consequently, the analyte molecules are subjected to very large electric fields of the order of 107 Vcm-1. Ionization occurs from their distorted electronic states of reduced ionization energy, using the laser. Negative ion detection is also demonstrated, occurring due to the capture of produced photoelectrons. LAPSI MS can be used for monitoring in situ photoassisted reactions like the decarboxylation of mercaptobenzoic acid in the presence of gold and silver nanoparticles and the dehydrogenation reaction of 2,3-dihydro-1 H-isoindole, which were chosen as examples. As an application, we have shown that paraffin oil, which is usually nonionizable by paper spray or by electrospray ionization can be efficiently detected using this technique. Impurities like mineral oils were detected easily in commercially available coconut oil, pointing the way to applications of social relevance.

In Vivo Real-Time Monitoring System Using Probe Electrospray Ionization/Tandem Mass Spectrometry for Metabolites in Mouse Brain.

Recent improvements in ambient ionization techniques combined with mass spectrometry has enabled to achieve real-time monitoring of analytes of interest, even for biogenic molecules in living animals. Here, we demonstrate a newly developed system for in vivo real-time monitoring of metabolites in a living mouse brain. It consists of a semiautomated manipulation system and a unique probe electrospray ionization unit, which uses an extremely thin solid needle (tip dia.: 700 nm) for direct sampling and ionization, coupled to a conventional tandem mass spectrometer. The system successfully monitored 8 cerebrum metabolites related to central energy metabolism in an isoflurane-anesthetized mouse in real time with a 20 s interval. Moreover, our system succeeded in capturing dynamics of energy metabolism in a mouse administered with cannabinoid type-1 receptor agonist, which is known to disrupt cerebrum energy metabolism. The present system now opens the door to the next stage of cutting-edge technique in achieving in vivo real-time monitoring.

Detection of potential new biomarkers of atherosclerosis by probe electrospray ionization mass spectrometry.

Atherosclerotic diseases are the leading cause of death worldwide. Biomarkers of atherosclerosis are required to monitor and prevent disease progression. While mass spectrometry is a promising technique to search for such biomarkers, its clinical application is hampered by the laborious processes for sample preparation and analysis. We developed a rapid method to detect plasma metabolites by probe electrospray ionization mass spectrometry (PESI-MS), which employs an ambient ionization technique enabling atmospheric pressure rapid mass spectrometry. To create an automatic diagnosis system of atherosclerotic disorders, we applied machine learning techniques to the obtained spectra. Using our system, we successfully discriminated between rabbits with and without dyslipidemia. The causes of dyslipidemia (genetic lipoprotein receptor deficiency or dietary cholesterol overload) were also distinguishable by this method. Furthermore, after induction of atherosclerosis in rabbits with a cholesterol-rich diet, we were able to detect dynamic changes in plasma metabolites. The major metabolites detected by PESI-MS included cholesterol sulfate and a phospholipid (PE18:0/20:4), which are promising new biomarkers of atherosclerosis. We developed a remarkably fast and easy method to detect potential new biomarkers of atherosclerosis in plasma using PESI-MS.

Effect-directed analysis via hyphenated high-performance thin-layer chromatography for bioanalytical profiling of sunflower leaves

High-performance thin-layer chromatography (HPTLC) coupled with effect-directed analysis was used for non-targeted screening of sunflower leaf extract for components exhibiting antioxidant, antibacterial and/or cholinesterase enzyme inhibitory effects. The active compounds were characterized by HPTLC-electrospray ionization-high resolution mass spectrometry (ESI-HRMS) and HPTLC-Direct Analysis in Real Time (DART)-MS/MS. The latter ambient ionization technique (less soft than ESI) resulted in oxidation and fragmentation products and characteristic fragment ions. NMR spectroscopy after targeted isolation via preparative normal phase flash chromatography and semi-preparative reversed phase high-performance liquid chromatography supported the identification of two diterpenes to be (-)-kaur-16-en-19-oic acid and 15-α-angeloyloxy-ent-kaur-16-en-19-oic acid. Both compounds found to be multi-potent as they inhibited acetylcholinesterase and butyrylcholinesterase and showed antibacterial effects against Gram-positive Bacillus subtilis and Gram-negative Aliivibrio fischeri bacteria. Kaurenoic acid was also active against the Gram-negative pepper pathogenic Xanthomonas euvesicatoria bacteria.

Monitoring Dopamine ex Vivo during Electrical Stimulation Using Liquid-Microjunction Surface Sampling.

Liquid-microjunction surface sampling (LMJ-SS) is an ambient ionization technique based on the continuous flow of solvent using an in situ microextraction device in which solvent moves through the probe, drawing in the analytes in preparation for ionization using an electrospray ionization source. However, unlike traditional mass spectrometry (MS) techniques, it operates under ambient pressure and requires no sample preparation, thereby making it ideal for rapid sampling of thicker tissue sections for electrophysiological and other neuroscientific research studies. Studies interrogating neural synapses, or a specific neural circuit, typically employ thick, ex vivo tissue sections maintained under near-physiological conditions to preserve tissue viability and maintain the neural networks. Deep brain stimulation (DBS) is a surgical procedure used to treat the neurological symptoms that are associated with certain neurodegenerative and neuropsychiatric diseases. Parkinson's disease (PD) is a neurological disorder which is commonly treated with DBS therapy. PD is characterized by the degeneration of dopaminergic neurons in the substantia nigra pars compacta portion of the brain. Here, we demonstrate that the LMJ-SS methodology can provide a platform for ex vivo analysis of the brain during electrical stimulation, such as DBS. We employ LMJ-SS in the ex vivo analysis of mouse brain tissue for monitoring dopamine during electrical stimulation of the striatum region. The mouse brain tissue was sectioned fresh post sacrifice and maintained in artificial cerebrospinal fluid to create near-physiological conditions before direct sampling using LMJ-SS. A selection of metabolites, including time-sensitive metabolites involved in energy regulation in the brain, were identified using standards, and the mass spectral database mzCloud was used to assess the feasibility of the methodology. Thereafter, the intensity of m/z 154 corresponding to protonated dopamine was monitored before and after electrical stimulation of the striatum region, showing an increase in signal directly following a stimulation event. Dopamine is the key neurotransmitter implicated in PD, and although electrochemical detectors have shown such increases in dopamine post-DBS, this is the first study to do so using MS methodologies.

Forensic Sampling and Analysis from a Single Substrate: Surface-Enhanced Raman Spectroscopy Followed by Paper Spray Mass Spectrometry

Sample preparation is the most common bottleneck in the analysis and processing of forensic evidence. Time-consuming steps in many forensic tests involve complex separations, such as liquid and gas chromatography or various types of extraction techniques, typically coupled with mass spectrometry (e.g., LC-MS). Ambient ionization ameliorates these slow steps by reducing or even eliminating sample preparation. While some ambient ionization techniques have been adopted by the forensic community, there is significant resistance to discarding chromatography as most forensic analyses require both an identification and a confirmation technique. Here, we describe the use of a paper substrate, the surface of which has been inkjet printed with silver nanoparticles, for surface enhanced Raman spectroscopy (SERS). The same substrate can also act as the paper substrate for paper spray mass spectrometry. The coupling of SERS and paper spray ionization creates a quick, forensically feasible combination.

Direct detection of surface localized specialized metabolites from Glycyrrhiza lepidota (American licorice) by leaf spray mass spectrometry

Leaf spray-MS minimizes tissue manipulation by effectively and quickly assessing in vivo specialized metabolites from intact plant tissue surfaces, including trichome metabolites. Intact leaves of Glycyrrhiza lepidota Pursh. (American licorice) were analyzed by direct electrospray leaf spray-MS, an ambient ionization technique. Comparison of metabolites detected by leaf spray-MS to those from LC-MS of bulk tissue and trichome enriched extracts showed dramatic differences. Leaf spray-MS results suggest that in specific situations this approach could complement traditional LC-MS analysis of bulk extracts. Leaf spray-MS as a metabolomics technique eliminates sample pretreatment and preparation allowing for rapid sampling in real time of living intact tissues. Specialized metabolites on the surface of tissues such as glandular trichomes metabolites are detected by leaf spray-MS.

Rapid fingerprinting of lignin by ambient ionization high resolution mass spectrometry and simplified data mining

Ambient ionization techniques are typically used to analyze samples in their native states with minimal or no sample pretreatment prior to mass spectrometric (MS) analysis. Desorption electrospray ionization (DESI) and direct analysis in real time (DART) were systematically investigated in this work for direct solid analysis of depolymerized lignin samples, with the goal of rapidly fingerprinting these samples, to efficiently characterize the subunits of this renewable energy source. High resolution MS was required for enhanced selectivity in this study due to the inherent structural complexity of lignin. DESI provided results across a broader mass range (up to m/z 700) than DART and also ionized saturated compounds of low oxygen-to-carbon (O/C) ratios and low double bond equivalents (DBE). While DART detected the same core lignin monomeric and dimeric compounds as seen with DESI and electrospray ionization (ESI), results were restricted to a narrower mass range to m/z 500, due to thermal degradation and losses of methoxy groups. In contrast to DESI and ESI, the DART spectra were nearly void of saturated components. On a structural level, the core lignin compounds were visually fingerprinted and ionization method performances critically assessed by employing simplified Kendrick-based data mining approaches. A novel simplified data visualization approach was developed in this work based on modified Kendrick mass defect (KMD) filtering for lignin subunits and plotting the mass defect values against the degree of unsaturation. Direct visualization of monomeric, dimeric and trimeric lignin species was simplified by the KMD separation plots, easily allowing the core lignin compounds to be visually identified and compared. Modified KMD bases, namely methoxy and phenol bases, which represent monomer-specific lignin constituents, were successfully used to classify and group the complex mixture of lignin species. Further separation of methoxy-related lignin species was successfully achieved by employing the more specific phenolic KMD base.

A cautionary note on the effects of laboratory air contaminants on ambient ionization mass spectrometry measurements.

Ambient ionization mass spectrometry methods are convenient, sensitive and require little sample preparation. However, they are susceptible to species present in air surrounding the mass spectrometer. This study identifies some challenges associated with the potential impacts of indoor air contaminants on ionization and analysis involving open-air methods. Unexpected effects of volatile organic compounds (VOCs) from floor maintenance activities on ambient ionization mass spectrometry were studied using three different ambient ionization techniques. Extractive electrospray ionization (EESI), direct analysis in real time (DART) and ionization by piezoelectric direct discharge (PDD) plasma were demonstrated in this study to be affected by indoor air contaminants. Identification of contaminant vapors was verified by comparison with standards using EESI-MS/MS product ion scans. Emissions of diethylene glycol monoethyl ether and ethylene glycol monobutyl ether are identified from floor stripping and waxing solutions using three ambient ionization mass spectrometry techniques. These unexpected indoor air contaminants are capable of more than 75% ion suppression of target analytes due to their high volatility, proton affinity and solubility compared with the target analytes. The contaminant vapors are also shown to form adducts with one of the target analytes. The common practice in MS analysis of subtracting a background air spectrum may not be appropriate if the presence of ionizable air contaminants alters the spectrum in unexpected ways. For example, VOCs released into air from floor stripping and waxing are capable of causing ion suppression of target analytes.

Application of paper spray ionization for explosives analysis.

A desired feature in the analysis of explosives is to decrease the time of the entire analysis procedure, including sampling. A recently utilized ambient ionization technique, paper spray ionization (PSI), provides the possibility of combining sampling and ionization. However, an interesting phenomenon that occurs in generating negatively charged ions pose some challenges in applying PSI to explosives analysis. The goal of this work is to investigate the possible solutions for generating explosives ions in negative mode PSI. The analysis of 2,4,6-trinitrotoluene (TNT), pentaerythritol tetranitrate (PETN), octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX), and 1,3,5-trinitroperhydro-1,3,5-triazine (RDX) was performed. Several solvent systems with different surface tensions and additives were compared to determine their effect on the ionization of explosives. The solvents tested include tert-butanol, isopropanol, methanol, and acetonitrile. The additives tested were carbon tetrachloride and ammonium nitrate. Of the solvents tested, isopropanol yielded the best results. In addition, adding ammonium nitrate to the isopropanol enhanced the analyte signal. Experimentally determined limits of detection (LODs) as low as 0.06ng for PETN, on paper, were observed with isopropanol and the addition of 0.4mM ammonium nitrate as the spray solution. In addition, the explosive components of two plastic explosive samples, Composition 4 and Semtex, were successfully analyzed via surface sampling when using the developed method. The analysis of explosives using PSI-MS in negative ion mode was achieved. The addition of ammonium nitrate to isopropanol, in general, enhanced the analyte signal and yielded better ionization stability. Real-world explosive samples were analyzed, which demonstrates one of the potential applications of PSI-MS analysis.

Intact metabolite profiling of mouse brain by probe electrospray ionization/triple quadrupole tandem mass spectrometry (PESI/MS/MS) and its potential use for local distribution analysis of the brain

Probe electrospray ionization (PESI), which is an ambient ionization technique, enables us to analyze intact endogenous metabolites without sample preparation. In this study, we applied the newly developed method of PESI coupled to tandem mass spectrometry (PESI/MS/MS) to analyze metabolites in mouse brain, where its lipid composition often interfere with MS-based metabolome analysis. As a result, PESI/MS/MS directly detected 25 metabolites in a mouse frontal cortex, and clearly discriminated the metabolic profiles of mice model with energy metabolism disruption from control mice. PESI/MS/MS also allowed us to perform local distribution analysis of the hippocampus as well as the frontal cortex in each mouse (n = 5), discriminating their subtle metabolic differences. These results showed high potential of PESI/MS/MS for direct metabolome profiling of mouse brain.

On-line reaction monitoring by mass spectrometry, modern approaches for the analysis of chemical reactions.

The application of on-line mass spectrometry for direct analysis of chemical and other types of process continues to grow in importance and impact. The ability of the technique to characterize many aspects of a chemical reaction such as product and impurity formation, along with reactant consumption in a single experiment is key to its adoption and development. Innovations in ionization techniques and mass spectrometry instrumentation are enabling this adoption. An increasing range of ambient ionization techniques make on-line mass spectrometry applicable to a large range of chemistries. The academic development and commercialization of small footprint portable/transportable mass spectrometers is providing technology that can be positioned with any process under investigation. These developments, coupled with research into new ways of sampling representatively from both the condensed and gaseous phases, are positioning mass spectrometry as an essential technology for on-line process optimization, understanding and intelligent control. It is recognized that quantitative capability of mass spectrometry in this application can cause some resistance to its adoption, but research activities to tackle this limitation are on-going.

Rapid analysis of forensic-related samples using two ambient ionization techniques coupled to high-resolution mass spectrometers.

This paper highlights the versatility of interfacing two ambient ionization techniques, Laser Diode Thermal Desorption (LDTD) and Atmospheric Solids Analysis Probe (ASAP), to high-resolution mass spectrometers and demonstrate the method's capability to rapidly generate high-quality data from multiple sample types with minimal, if any, sample preparation. For ASAP-MS analysis of solid and liquid samples, the material was transferred to a capillary surface before being introduced into the mass spectrometer. For LDTD-MS analysis, samples were solvent extracted, spotted in a 96-well plate, and the solvent was evaporated before being introduced into the mass spectrometer. All analyses were performed using Atmospheric Pressure Chemical Ionization in positive mode. Seven consumer "Spice" packets were combined and analyzed by both ASAP and LDTD, which identified 11 synthetic cannabinoids/cathinones by full MS and MS/MS experiments. To further show the usefulness of these techniques, black tar heroin was analyzed, which resulted in the identification of heroin and its impurities (monoacetylmorphine, papaverine, and noscapine). These experiments were performed on the LTQ-Orbitrap to demonstrate the ability to perform both parallel and serial MS and MSn experiments. Interfacing LDTD and ASAP to high-resolution mass spectrometers allows for expeditious analysis of a wide range of samples, with minimal or no sample preparation. Both allow for rapid full scan, MS/MS, and/or MSn experiments from a single sample introduction. Published in 2017. This article is a U.S. Government work and is in the public domain in the USA.

Analysis of synthetic phenethylamine street drugs using direct sample analysis coupled to accurate mass time of flight mass spectrometry

Serious health complications and fatal overdoses have brought phenethylamine, otherwise known as 2C, drug abuse to the public’s attention. These compounds are 2C-X series analogs of mescaline. The name “2C” results from the two carbons in the ethyl chain. The substituents on these emerging drugs are constantly changed in order to avoid listing as controlled substances. These synthetic drugs are marketed as having affects similar to LSD and MDMA and are typically consumed sublingually via blotter paper. Twenty-six commercially available standards were analyzed using a direct sample analysis technique coupled to accurate mass time of flight mass spectrometry. Direct sample analysis is an ambient ionization technique employing direct charge transfer from nitrogen reagent gas resulting in ionization and in-source collision induced dissociation. Mass spectral analysis was used to determine the fragmentation patterns of the 2C compounds. While the mass spectral data for the compounds are similar in fragmentation, they also display differences that allow the analyst to distinguish which compound is present. The fragmentation patterns, high-resolution mass spectral data, and isotope ratios are used to qualitatively identify two blotter paper street samples that were extracted together. As these drugs are emerging substances of abuse, there are no generally accepted protocols for this analysis. Additionally, presumptive, or screening, tests have not been widely developed for these materials. Direct sample analysis allows for a quick screening of seized compounds resulting in a preliminary identification, which can then be analyzed and confirmed using other analytical techniques.

Clinical Application of Ambient Ionization Mass Spectrometry.

Ambient ionization allows mass spectrometry analysis directly on the sample surface under atmospheric pressure with almost zero sample pretreatment. Since the development of desorption electrospray ionization (DESI) in 2004, many other ambient ionization techniques were developed. Due to their simplicity and low operation cost, rapid and on-site clinical mass spectrometry analysis becomes real. In this review, we will highlight some of the most widely used ambient ionization mass spectrometry approaches and their applications in clinical study.

Solvent gradient electrospray for laser ablation electrospray ionization mass spectrometry.

Most electrospray based ambient ionization techniques, e.g., laser ablation electrospray ionization (LAESI), utilize a fixed spray solution composition. Complex samples often contain compounds of different polarity that exhibit a wide range of solubilities in the electrospray solvent. Thus, the fixed spray solution composition limits the molecular coverage of these approaches. Two-barrel theta glass capillaries have been used for the rapid mixing of two solutions for manipulating fast reactions including protein folding, unfolding, and charge state distributions. Here, we present a new variant of LAESI mass spectrometry (MS) by scanning the high voltages applied to the two barrels of a theta glass capillary containing two different solvents. In the resulting gradient LAESI (g-LAESI), the composition of the spray solution is ramped between the two solvents in the barrels to facilitate the detection of compounds of diverse polarity and solubility. Dynamic ranges and limits of detection achieved for g-LAESI-MS were comparable to conventional LAESI-MS. We have demonstrated simultaneous detection of different types of chemical standards, and polar and less polar compounds from Escherichia coli cell pellets using g-LAESI-MS. Varying the spray solution composition in a gradient electrospray can benefit from the enhanced solubilities of different analytes in polar and less polar solvents, ultimately improving the molecular coverage in the direct analysis of biological samples.

Analytical Validation of a Portable Mass Spectrometer Featuring Interchangeable, Ambient Ionization Sources for High Throughput Forensic Evidence Screening.

Forensic evidentiary backlogs are indicative of the growing need for cost-effective, high-throughput instrumental methods. One such emerging technology that shows high promise in meeting this demand while also allowing on-site forensic investigation is portable mass spectrometric (MS) instrumentation, particularly that which enables the coupling to ambient ionization techniques. While the benefits of rapid, on-site screening of contraband can be anticipated, the inherent legal implications of field-collected data necessitates that the analytical performance of technology employed be commensurate with accepted techniques. To this end, comprehensive analytical validation studies are required before broad incorporation by forensic practitioners can be considered, and are the focus of this work. Pertinent performance characteristics such as throughput, selectivity, accuracy/precision, method robustness, and ruggedness have been investigated. Reliability in the form of false positive/negative response rates is also assessed, examining the effect of variables such as user training and experience level. To provide flexibility toward broad chemical evidence analysis, a suite of rapidly-interchangeable ion sources has been developed and characterized through the analysis of common illicit chemicals and emerging threats like substituted phenethylamines. Graphical Abstract ᅟ.

Metal Cationization Extractive Electrospray Ionization Mass Spectrometry of Compounds Containing Multiple Oxygens.

Extractive electrospray ionization is an ambient ionization technique that allows real-time sampling of liquid samples, including organic aerosols. Similar to electrospray ionization, the composition of the electrospray solvent used in extractive electrospray ionization can easily be altered to form metal cationized molecules during ionization simply by adding a metal salt to the electrospray solvent. An increase in sensitivity is observed for some molecules that are lithium, sodium, or silver cationized compared with the protonated molecule formed in extractive electrospray ionization with an acid additive. Tandem mass spectrometry of metal cationized molecules can also significantly improve the ability to identify a compound. Tandem mass spectrometry of lithium and silver cationized molecules can result in an increase in the number and uniqueness of dissociation pathways relative to [M + H]+. These results highlight the potential for extractive electrospray ionization with metal cationization in analyzing complex aerosol mixtures. Graphical Abstract ᅟ.

Comparison of paper spray mass spectrometry analysis of dried blood spots from devices used for in-field collection of clinical samples

Paper spray (PS) is an ambient ionization technique applicable to ionizing analytes from untreated dried biofluid samples. In-field sample analysis could benefit from the capability to use a finger prick of blood to measure drugs in whole blood at low cost and in a short time. Some studies may require specialized blood collection devices that can be used in remote areas. In this study, four different dried blood spot (DBS) devices are used with PS sources and tested for rapid quantification of imatinib and N-desmethyl-imatinib. A triple quadrupole mass spectrometer allows analyte detection with high sensitivity. Analytical figures of merit for the four devices are compared, and it is concluded that several of the novel devices successfully deploy DBS with PS and yield similar results to traditional manual PS methods. Clinical samples collected in a remote location were analyzed as a proof of concept for in-field blood collection and subsequent rapid laboratory analysis. Graphical abstract Dried blood spot analyis by paper spray ionization MS/MS for in field sample collection.